2012 Mercedes-Benz ML550

Recalls

3 recalls name the 2012 Mercedes-Benz ML550. Newest first.

• Fuel system, diesel › Delivery › Fuel pump › Control/drive module

  Dec 23, 2022NHTSA 22V955000348,183 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML550, 2012-2015 ML350, AMG ML63, 2015 ML250, ML400, 2016 GLE450, GLE300, 2016-2018 GLE350, GLE550, 2016-2019 GLE400, 2017-2019 AMG GLE43, and 2016-2020 AMG GLE63 vehicles. Water might accumulate in the spare tire wheel well and damage the fuel pump control unit, which could cause an engine…

  Risk and remedy

  Risk

  An engine stall while driving increases the risk of a crash.

  Remedy

  Dealers will install a water drain plug, inspect for water intrusion, and replace the fuel pump control unit as necessary, free of charge. Owner notification letters were mailed February 15, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers for this recall are 2023010002 and 2023010003.

  Full recall details →

• Suspension › Front

  Apr 27, 2018NHTSA 18V2720009,725 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML350 Bluetec 4Matic and ML550 4Matic, 2012-2015 ML63 AMG 4Matic and ML350 4Matic, 2013-2016 GL350 Bluetec 4Matic, GL550 4Matic and GL63 AMG 4Matic, 2017 GLS350d 4Matic, GLS450 4Matic, GLS550 4Matic and GLS63 AMG 4Matic, 2015 ML400 4Matic, 2016 GLE400 4Matic, GLE350 4Matic, GLE63 AMG 4Matic…

  Risk and remedy

  Risk

  The leaking oil in the presence of an ignition source can increase the risk of a fire.

  Remedy

  MBUSA will notify owners, and dealers will correct the oil level as necessary and replace the reservoir sealing cap to prevent oil foam from leaking out, free of charge. The recall began August 30, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018070015.

  Full recall details →

• Equipment

  Aug 9, 2012NHTSA 12E0280008,879 vehiclesEquipment

  Mercedes-Benz is recalling certain accessory all-season floor mats sold for use in model year 2012 and 2013 Mercedes-Benz ML-Class vehicles. This all-season floor mat may not fully conform to the contour of the vehicle's floor plan as intended. Clearance between the mat and the gas pedal may be reduced, possibly allowing the pedal to become trapped.

  Risk and remedy

  Risk

  This interference could prevent the gas pedal from retracting and the vehicle may not decelerate as expected when the driver lifts their foot from the gas pedal, which could increase the risk of a crash. Should the pedal become trapped, steady application of the brakes will allow the vehicle to be brought to a stop.

  Remedy

  Mercedes-Benz will notify owners, and dealers will replace the floor mats free of charge. Until replacement mats become available, consumers are advised to remove their floor mats from the vehicle. The safety recall began on December 21, 2012. Only vehicles equipped with the accessory floor mats are affected. Owners may contact Mercedes-Benz for more information at 1-800-367-6372.

  Full recall details →

Owner complaints

What owners report most

1. Electrical system1
2. Engine1
3. Fuel/propulsion system1
4. Lane departure1

Latest complaints

• Oct 27, 2026MN
  Fuel/propulsion system
  *2012 ML550 benz fuel pump control module Re: Formal Demand for Repair – Fuel Pump Control Unit Replacement Vehicle: Mercedes‑Benz ML550 VIN: [XXX] Recall: NHTSA Recall Campaign No. XXX To Mercedes‑Benz USA: I am submitting this formal demand for repair of the cost to replace the fuel pump…

  *2012 ML550 benz fuel pump control module Re: Formal Demand for Repair – Fuel Pump Control Unit Replacement Vehicle: Mercedes‑Benz ML550 VIN: [XXX] Recall: NHTSA Recall Campaign No. XXX To Mercedes‑Benz USA: I am submitting this formal demand for repair of the cost to replace the fuel pump control unit in my Mercedes‑Benz ML550. The vehicle stalled without warning while in operation, creating an immediate safety hazard. A certified mechanic diagnosed the issue and confirmed that the fuel pump control unit was reporting a fault through the onboard diagnostics system, accompanied by an illuminated check engine light. Due to the intermittent nature of the defect and the risk of sudden failure, replacement of the fuel pump control unit was the only available remedy. During my extensive research, I become aware of NHTSA Recall Campaign No. XXX, which identifies defective fuel pump control units in this vehicle model. The failure I experienced, the diagnostic findings, and the circumstances of the stall are consistent with the defect described in the recall. I purchased this vehicle from an authorized Mercedes‑Benz USA dealer, and my personal contact information was collected at the time of sale. I did not receive any recall notification from Mercedes‑Benz USA. As a result of this failure to notify, I strongly recommend repair expenses should be covered under the recall campaign. The defective fuel pump control unit was identified by the mechanic after the symptoms and diagnostic information acquired. Thanks you INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• Mar 15, 2023RI
  Electrical system · Engine · Lane departure › Blind spot detection
  In the last year, randomly, when starting the vehicle, the yellow check engine light comes on. Turn the vehicle off, it is gone. The side view mirrors have the yellow lights lit up on them when driving down any road, the red warning lights that tell you there's something behind or in front of…

  In the last year, randomly, when starting the vehicle, the yellow check engine light comes on. Turn the vehicle off, it is gone. The side view mirrors have the yellow lights lit up on them when driving down any road, the red warning lights that tell you there's something behind or in front of you start going off for no reason while driving down any road, all the "safety" and lane assist features seem to have a ghost controlling them. The radio will also glitch out from time to time. It will swap through the channels or pull up list of channels when there is Nobody in the vehicle messing with it at all. Yesterday, I received the message that the backup assist was not working and another about lane assist not working. This morning, both messages are gone and things seem to be normal. This is very distracting! I've been on the highway, in the high speed lane and my alert is flashing and loudly sounding. It startled me, caused me to abruptly slow down and start looking all around; I was concerned someone was about to hit me or worse, I was about to hit something I couldn't see; it turns out there was nothing in front of, behind or around me at all. This needs to get resolved, asap. It appears to me to be a computer/electrical issue. It seems that there are many others complaining about very similar issues! Come on Mercedes-Benz, let's put out the recall already! The dealership just says "unless it's doing it while it's here, there's not much I can do". Of course it is never doing it then! Unreal!!!!

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
• 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
• 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11010750Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to FIN vehicle identification end number. If vehicle falls outside of FIN range, create a TIPS case. Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
• 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11008070Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to VIN vehicle identification end number. If vehicle falls outside of VIN range, create a TIPS case. Model series 192: xxx xxx xx 182881 Model series 232: xxx xxx xx 182883 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
• 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10248173Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2009-2012 GL-Class, ML-Class, R-Class, and S-Class (164/166, 251, 221 platforms) vehicles, the coding for the engine control unit does not correspond to the specifications as part of the BlueTEC update diesel field measure (aka Emission Modification). This could result in the VIN number not being read out from the vehicle. This could affect the vehicle smog check. MBUSA will conduct an Emission Service Campaign in which an authorized Mercedes-Benz dealer will update the SCN coding for the engine control unit on the affected vehicles.
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10233794Why the warranty extension? On certain Model Year 2011-2016 CL/CLS/S/E/ML/SL/G/GL/GLE-Class vehicles with V8 engines, the exhaust valve assembly might not work properly and result in an engine misfire and potential illumination of the check engine Malfunction Indicator Lamp (MIL).
• 10233778In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the exhaust valve system in certain Model Year (MY) vehicles listed below as follows: - MY2011: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 12 years / 120,000 miles (whichever occurs first) - MY2012: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 11 years / 120,000 miles (whichever occurs first) - MY2013 MY 2016: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 10 years / 120,000 miles (whichever occurs first) This extended warranty applies to the following condition that may necessitate the repair or replacement of components related to the exhaust valve assembly (e.g. exhaust valve, cylinderhead) related to: Over time, increased lateral forces may lead to wear in the valve guide and/or seat ring. This issue could potentially cause combustion misfire for cylinder 1 through 8 (right and/or left cylinder head), resulting in an activation of the check engine Malfunction Indicator Lamp (MIL) .
• 10208744Complaint The touchpad dimming function does not work and the search lighting is either at maximum brightness or fully off (dependent upon dimming signal). Note: The dimming functions of the instrument cluster and head unit display are not affected and remain fully functional. Cause Touchpad (A105) hardware Remedy The serial numbers of the potentially affected parts can be found in the attached list. The serial number can be found on the touchpad itself or in Vedoc (Vedoc -> control units -> TPAD -> serial number). If the serial number listed in VeDoc or on the part (these numbers should be identical) matches one of the serial numbers in the attachment and the described complaint is present, then the touchpad may be replaced.
• 10205234Software update of COMAND Online control unit.
• 10205233Mobile phone cotacts are not transferred completely.
• 10202531Touch pad: Search lighting does not dim or does not turn on.
• 10186145Creaking noise from fixed glass section of panoramic roof in area of rear passenger compartment grab handles
• 10186144Armrest In Center Console (Front) Only Opens On One Side Or Not At All - Model Series 167
• 10184799Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain Mercedes-Benz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or caused to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed.
• 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
• 10178745The aluminum bolts of the steering gear housing cover and the aluminum bolts on the powerpack may corrode in corrosion-critical countries where exposed combination with particularly aggressive thawing agents (saltwater mixtures) in certain vehicles of the model series 166, 292, W/X 204, 212, 213, 205, 253, 218, 222, 217, 207. This fault pr expected in countries that do not use these thawing agents. In the case of advanced corrosion, the bolt strength may be impaired. Over time and with ongoing corrosion in combination with associated with driving, it cannot be excluded that a corroded bolt may break in individual cases. If all 3 mounting bolts of the powerpack were to break over time, this could detach from the The power steering would as a result fail.
• 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
• 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
• 10167577Since 12/2012 (model 166) and since 06/2013 (model 242) the glass breakage loops are no longer in the side windows and rear window. Suitable interior protection ensures that the interior monitoring function continues to operate correctly.
• 10167565A flapping/rattling noise can be heard from the area of the center console towards the rear.
• 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
• 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
• 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
• 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
• 10167549Thumping noises at the front axle when driving over road bumps
• 101675481. In vehicles up to VIN 166 ### #A 097760 without code 803, the following fault code is logged in the quick test: P1C9B00. The control unit 'Roll control' has a malfunction. 2. In vehicles up to VIN 166 ### #A 097760 with code 803 or vehicles as of VIN 166 ### #A 097761, the following fault code is logged in the quick test: P1C9564. The rotation direction valve of the torsion bar ''Front axle'' has a malfunction.
• 10167546FC 2783 (Friction power of torque converter lockup clutch is too high) or FC 0741 (Actuation of torque converter lockup clutch not possible) stored in transmission control unit. One possible additional customer complaint could be "poor acceleration" e.g. due to engine intervention. This can affect all NAT2FE+ (7G-TRONIC PLUS) vehicles with engines OM651, OM642LS and M278 in the production period from 04/2011 to 02/2012 and with more than 10,000 km. The two fault codes can also occur in combination with rpm sensor faults (see also GI27.50-P-035556). The rpm sensor fault is not connected with this complaint.

Every Mercedes-Benz ML550 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.