2022 Mercedes-Benz S 580 4MATIC
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › S 580 4MATIC › 2022
These records cover every 2022 Mercedes-Benz S 580 4MATIC. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
8 recalls name the 2022 Mercedes-Benz S 580 4MATIC. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2022-2025 S 500 4MATIC, Maybach S 580 4MATIC, Maybach S 680 4MATIC, S 580 4MATIC, 2023-2025 S 580 E 4MATIC, and 2024-2025 AMG S 63 E Performance vehicles. The front brake hoses may rupture and leak brake fluid.
Risk and remedy
Risk
A brake fluid leak can extend the distance needed to stop the vehicle, increasing the risk of a crash.
Remedy
Dealers will replace the front brake hoses, free of charge. Owner notification letters are expected to be mailed November 27, 2026. Owners may contact MBUSA customer service at 1-800-367-6372. This recall expands previous NHTSA recall number 25V116. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 9, 2026.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2022 S 500, Maybach S 580 4MATIC, 2021-2023 S 580 4MATIC, 2022 S 680 4MATIC, and 2023 S 580e 4MATIC vehicles. The front brake hoses may rupture and leak brake fluid.
Risk and remedy
Risk
A brake fluid leak can extend the distance needed to stop the vehicle, increasing the risk of a crash.
Remedy
Dealers will replace the front brake hoses, free of charge. Owner notification letters were mailed April 25, 2025. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2025030007.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2023 S580, and Maybach S580 vehicles. In the event of a mechanical failure in the engine Camtronic system, the engine control unit (ECU) software may cause the engine to overheat or stall.
Risk and remedy
Risk
An engine stall can increase the risk of a crash. In addition, an engine that overheats can increase the risk of a fire.
Remedy
Dealers will update the ECU software, free of charge. Owner notification letters were mailed on November 15, 2024. Owner notification letters will be mailed in phases, on November 15, 2024, January 10, 2025, and February 21, 2025. Owners can contact Mercedes-Benz Customer Service at 1-877-496-3691. MBUSA's number for this recall is 2024100007.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2024 GLE, GLS, C-Class, E-Class, S-Class, SL, GLC, CLS, AMG GT, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, causing a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 28, 2024. Owner notification letters will be mailed in phases, on February 23, 2024, April 19, 2024, June 28, 2024, August 9, 2024, October 1, 2024, and December 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 23V-445.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2023 C-Class, E-Class, S-Class, CLS, SL, GT, GLC, GLE, GLS, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, which can result in a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 14, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023070012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2022 S580Z, S500V, and S580V vehicles. The sub frame weld for the thrust arm on the rear axle carrier may have been improperly welded, causing the thrust arm to break and detach.
Risk and remedy
Risk
A detached thrust arm can cause a sudden loss of vehicle control, or cause the vehicle to pull to one side during emergency braking, increasing the risk of a crash.
Remedy
Owners are advised not to drive their vehicles until the remedy has been performed. Dealers will inspect the sub frame weld on the rear axle carrier and replace the rear axle carrier as necessary, free of charge. Owner notification letters were mailed April 8, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for the recall is 2022030028.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2022 C-Class, E-Class, S-Class, SL, EClass Coupe/Convertible, CLS, AMG GT 4-doors Coupe, and EQS vehicles with a heated leather steering wheel. Due to a software error in the hand detection control unit, the hands-off detection might not detect when the driver's hands are away from the steering wheel…
Risk and remedy
Risk
Deactivated hands-off detection will prevent DISTRONIC system features from functioning, including warnings to grab the steering wheel and calling first responders as part of the Active Emergency Stop Assist, which can increase the risk of a crash or injury.
Remedy
Dealers will update the hand detection control unit software for the DISTRONIC system, free of charge. Owner notification letters were mailed May 6, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022040010.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2022 EQS450, S500, and S580 vehicles. The communication module software may restrict or disable the emergency call system (eCall).
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting emergency services through the call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed February 23, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022010006.
Owner complaints
25 complaints1 involved a fire
What owners report most
Latest complaints
- Forward collision avoidance › Automatic emergency braking · Power train · Steering
The contact owns a 2022 Mercedes-Benz S 580. The contact stated that while driving at an undisclosed speed, the messages "Active Brake Assist Functions Currently Limited - See Owner's Manual", "Risk of Vehicle Rolling Away - N Activated Manually No Automatic Change To P", "Service Required Do Not…
The contact owns a 2022 Mercedes-Benz S 580. The contact stated that while driving at an undisclosed speed, the messages "Active Brake Assist Functions Currently Limited - See Owner's Manual", "Risk of Vehicle Rolling Away - N Activated Manually No Automatic Change To P", "Service Required Do Not Change Transmission Position", and "Active Parking Assist And Parktronic Inoperative - See Owner's Manual" were displayed, and an unknown warning light was illuminated. Additionally, the vehicle had experienced phantom braking and the transmission failed to shift into park(P) as needed. The contact moved the gear shifter back and forth before the proper gear was recognized. The vehicle was taken to the dealer, who determined that the steering column needed to be replaced. The contact emailed the manufacturer regarding the failure, but the email was returned as undeliverable. The failure mileage was approximately 18,000.
- Engine · Power train · Service brakes
Vehicle: 2022 Mercedes-Benz S580 The vehicle is experiencing a severe and violent drivetrain "jolt" or "push" during gear transitions, specifically when shifting from 5th to 6th gear at cruising speeds. On multiple occasions, the jolt was so forceful that passengers believed the vehicle had been…
Vehicle: 2022 Mercedes-Benz S580 The vehicle is experiencing a severe and violent drivetrain "jolt" or "push" during gear transitions, specifically when shifting from 5th to 6th gear at cruising speeds. On multiple occasions, the jolt was so forceful that passengers believed the vehicle had been rear-ended by another car. This behavior is unpredictable and creates a significant safety hazard, as it causes a sudden change in vehicle momentum while driving in traffic. The issue has been reported to the authorized dealer (Fields Mercedes Lakeland) multiple times. The dealer kept the vehicle for over 40 cumulative days and performed motor/transmission mount replacements and "software calibrations," yet the violent shifting persists. Additionally, the engine produces an excessive vibration and loud noise during extended operation in high temperatures, which ceases only when the ECO/Auto-stop mode engages. I am concerned that the transmission or torque converter may fail abruptly while at highway speeds, potentially leading to a loss of propulsion or a rear-end collision due to the unexpected deceleration/jolt behavior. The vehicle is suffering from chronic oil consumption issues. The 'Check Engine Oil Level (Add 1 Quart)' message has appeared twice: once on 10/31/2025 and again on 04/17/2026. This is despite the vehicle being exclusively serviced by Mercedes-Benz Lakeland. This recurring engine issue, combined with the violent drivetrain jolts and shifting failures, significantly compromises the vehicle's safety and reliability."
- Forward collision avoidance › Automatic emergency braking · Service brakes
On multiple occasions, after the vehicle had been parked and not driven for approximately five days or more, the automatic parking brake locked in place and would not release. I attempted standard methods to disengage the brake, including manual release procedures and lightly rocking the vehicle…
On multiple occasions, after the vehicle had been parked and not driven for approximately five days or more, the automatic parking brake locked in place and would not release. I attempted standard methods to disengage the brake, including manual release procedures and lightly rocking the vehicle, without success. The only way to release the brake was to apply significant pressure to the accelerator while in reverse, which caused the brake to suddenly unlock. The first incident occurred while the vehicle was parked in my home garage. At the time, my grandson was playing nearby. The sudden release of the brake after applying the accelerator created a dangerous situation and was extremely alarming. A second incident occurred several days later while I was on vacation. In this instance, I made sure no one was near the vehicle before attempting to release the brake. Anticipating the issue, I had my left foot ready to push on the breaks when I accelerated using my right foot which releases the parking. I brought the vehicle to a Mercedes-Benz dealership on January 5, 2026, where the car remained for nearly ten days. The dealership was able to replicate the issue exactly as described. The service advisor also had to apply significant accelerator pressure to release the locked parking brake. A certified Mercedes-Benz technician inspected the vehicle thoroughly, including scanning for fault codes and checking for rust or mechanical issues, but ultimately advised that this behavior was considered “normal operation.” I find this explanation concerning. Having to apply forceful acceleration to release a locked parking brake presents a clear safety risk, particularly in confined spaces such as garages or parking structures, and could easily result in property damage or personal injury
- Back over prevention › Warnings · Electrical system · Forward collision avoidance › Adaptive cruise control
Was driving the car at 3:00 P.M. and all of a sudden thr dash display when total black out nothing on the display screen. Speed,fuel,turnning singles nothing total black out. Took it to the dealership to fix as this can and would be a life threathing at loss of life could and can happen in a traffic sistiution
- Service brakes · Suspension · Wheels
Mercedes-Benz S580 equipped with 21-inch wheels has experienced numerous tire blowouts over the course of ownership — too many to count. The blowouts occurred during normal driving on typical roads. Several blowouts caused rim damage and created a dangerous situation, including moments where I…
Mercedes-Benz S580 equipped with 21-inch wheels has experienced numerous tire blowouts over the course of ownership — too many to count. The blowouts occurred during normal driving on typical roads. Several blowouts caused rim damage and created a dangerous situation, including moments where I nearly lost control of the vehicle. This appears to be a design defect involving the 21-inch wheel and low-profile tire configuration, which seems structurally inadequate for normal road conditions. The failures are recurring and not due to isolated hazards. Other S580 owners have reported identical issues with repeated blowouts on 21-inch wheels. This presents a serious safety hazard, and a permanent remedy is needed.
- Engine and engine cooling
The contact owns a 2022 Mercedes-Benz S 580. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated and the engine stalled. The vehicle was taken to the dealer, where it was diagnosed with a failed CAM shaft solenoid. The contact was informed that…
The contact owns a 2022 Mercedes-Benz S 580. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated and the engine stalled. The vehicle was taken to the dealer, where it was diagnosed with a failed CAM shaft solenoid. The contact was informed that the CAM shaft solenoid needed to be replaced. In addition, the contact was informed that the engine needed to be dismantled. The vehicle was not repaired. The manufacturer was made aware of the failure. The contact referenced an unknown recall with a similar failure description; however, the VIN was not under recall. The failure mileage was approximately 55,000.
- Electrical system · Engine · Unknown or other
Over ~3 years of ownership, the vehicle has experienced recurrent electrical and engine-management issues, resulting in 15+ service visits and ~100 cumulative days out of service at an authorized dealer. Patterns include: (1) electrical—keyless entry intermittently unresponsive, instrument cluster…
Over ~3 years of ownership, the vehicle has experienced recurrent electrical and engine-management issues, resulting in 15+ service visits and ~100 cumulative days out of service at an authorized dealer. Patterns include: (1) electrical—keyless entry intermittently unresponsive, instrument cluster flickering/rebooting, multiple warning messages including a battery/electrical icon, HVAC/A/C becoming inoperative without cooling; and (2) powertrain/engine—check-engine light (MIL) illuminated, hesitation/limited power on initial acceleration, and rough operation after start. Safety risk: intermittent failure to unlock/start can leave occupants stranded; loss of power/hesitation creates risk when merging or crossing intersections; multiple warning messages/flicker are distracting; and loss of A/C in hot conditions has required operation with windows down to avoid heat stress. Reproduction/confirmation: The concerns have been observed by the dealer on multiple visits with fault codes recorded (codes UNKNOWN to me). Repairs/updates have been attempted, but symptoms recur after service. The vehicle has been inspected repeatedly by the authorized dealer and remains available for inspection upon request. Warnings/symptoms prior to failure: intermittent MIL, battery/electrical warning, cluster glitches/flicker, and A/C blowing warm air; some events followed periods where the vehicle would not unlock or start on the first attempt. Root cause: UNKNOWN.
- Structure › Body · Visibility/wiper
Subject: Report of Spontaneous Sunroof Explosion - Mercedes S580 2022 Model Dear National Highway Traffic Safety Administration, I am writing to report a concerning incident that occurred on [XXX] at approximately [XXX] while I was driving my 2022 Mercedes S580 to work on [XXX] N. During my…
Subject: Report of Spontaneous Sunroof Explosion - Mercedes S580 2022 Model Dear National Highway Traffic Safety Administration, I am writing to report a concerning incident that occurred on [XXX] at approximately [XXX] while I was driving my 2022 Mercedes S580 to work on [XXX] N. During my drive, I experienced a sudden, loud explosion within the vehicle. Initially, I believed it was either a gunshot or that I had been rear-ended. In a state of confusion, I quickly pulled over to the shoulder to assess the situation. Upon closer inspection, I discovered that my sunroof had shattered spontaneously. I am certain that this was not caused by an external object, such as a falling stone. There were no overpasses, bridges, or surrounding traffic that could have contributed to the damage. This was an extremely frightening experience, and I believe it is important to bring this matter to your attention for safety considerations. I have also reported this incident to my local Mercedes-Benz dealership. Thank you for your attention to this serious safety concern. Sincerely, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Service brakes · Suspension · Wheels
mechanical and safety-related failures observed in a Mercedes-Benz vehicle, specifically involving the suspension system, wheels, and braking components. Despite extensive repair efforts—including replacement of all four wheels and tires, complete AWD four-wheel alignment, and diagnostics performed…
mechanical and safety-related failures observed in a Mercedes-Benz vehicle, specifically involving the suspension system, wheels, and braking components. Despite extensive repair efforts—including replacement of all four wheels and tires, complete AWD four-wheel alignment, and diagnostics performed at authorized Mercedes-Benz dealerships—the underlying issues persist. To date, the total cost incurred in attempting to remedy these defects exceeds $15,848. The vehicle and its components have been inspected by two independent Mercedes-Benz dealer service centers and a certified third-party auto inspection firm. All parties have confirmed, through drive testing and diagnostics, that the problems are reproducible and continue to impair vehicle safety and performance. The suspension and associated hardware have been identified as the root cause of instability and braking inconsistencies. These findings align with broader patterns observed in similar vehicles, suggesting a recurring defect that warrants intervention by the manufacturer. Despite clear evidence from multiple independent sources, the manufacturer has failed to initiate a recall or implement corrective measures. This failure poses an ongoing safety risk to operators and the general public. The vehicle remains available for further inspection upon request. Immediate attention to this matter is expected to prevent further liabilities and protect consumer welfare.
- Engine and engine cooling
The contact owns a 2022 Mercedes-Benz S580. The contact received notification of NHTSA Campaign Number: 24V704000 (Engine and Engine Cooling); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a…
The contact owns a 2022 Mercedes-Benz S580. The contact received notification of NHTSA Campaign Number: 24V704000 (Engine and Engine Cooling); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
- Electrical system · Engine · Forward collision avoidance › Adaptive cruise control
Check engine light came on few occasions. Took to the dealer and told it’s just a false alarm no problems. On the night of sept 12th 2024, I’m my way home I lost the ac cooling all of a sudden. I was only 5 mts from home. Once inside my garage I saw to my horror some smoke coming from under yhe…
Check engine light came on few occasions. Took to the dealer and told it’s just a false alarm no problems. On the night of sept 12th 2024, I’m my way home I lost the ac cooling all of a sudden. I was only 5 mts from home. Once inside my garage I saw to my horror some smoke coming from under yhe hood. Upon opening saw some charred wires and some wire smoldering and smoke was coming out of it. Scared for my family I parked my car outside overnite and called the dealer. They had the car towed away the next day. Got my car back on 6 th of November 2024, with a laundry list of problems and issues, that they had supposedly fixed. Three or four various engine wiring harnesses were replaced, due to charring or melting, probably due to the heat. The engine and transmission were lifted off to fix all the wires and what not. I have all the invoices. And video and pictures of some wires and smoke. They don’t have an explanation for this. The recent recall about ecu maybe suggests the overheating of engine and causing the wires to burn out and some wires started burning almost causing fire if not caught in time. Called Mbusa and they didn’t show any concern. But one week after this incident they issued that ecu engine heating warning. Off course there is no repair for that. This is a fire hazard waiting to happen.
- Service brakes
Brakes seize when wet. That is, after a car wash or following exposure to rain, the accelerator must be pressed with abnormally greater pressure to get car moving from parked position. Loud, screeching sound emanates when brake releases. This malady continues severally. Resting lightly on brake…
Brakes seize when wet. That is, after a car wash or following exposure to rain, the accelerator must be pressed with abnormally greater pressure to get car moving from parked position. Loud, screeching sound emanates when brake releases. This malady continues severally. Resting lightly on brake pedal to dry out turning brake rotors, does not help. Eventually, problem disappears until the next wet episode. -Per Mercedes Authorized Dealer, there is no fix; problem is common to Mercedes 223 series. -Risk of collision exists in both modes, Drive as well as Reverse. This, due to sudden jump forward or rearward under brake-seize conditions. -Issue is ongoing, not a single incident. Remains unresolved. [At age [XXX] , I have over [XXX] driving experience. The above is an abnormal-with-risk, issue.] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Tires
The contact owns a 2022 Mercedes-Benz S580 equipped with Pirelli Tires, Tire Line: PZero PZ4, Tire Size: 255/35/R21, DOT Number: [XXX] . The contact stated that the vehicle was purchased 6 months prior and while observing the vehicle, both the front original tires had bubbles. The vehicle was taken…
The contact owns a 2022 Mercedes-Benz S580 equipped with Pirelli Tires, Tire Line: PZero PZ4, Tire Size: 255/35/R21, DOT Number: [XXX] . The contact stated that the vehicle was purchased 6 months prior and while observing the vehicle, both the front original tires had bubbles. The vehicle was taken to the dealer. The tires were replaced with the same brand and tire line. The contact stated that while driving approximately 40 MPH 4-months later, the passenger's side front tire had a blowout. The vehicle was towed to a different dealer. The tire was replaced with the same brand and tire line. The contact stated that 2 months later, the failure recurred with the passenger's side front tire where there were bubbles on the tire. The vehicle was taken to the initial dealer. The tire was replaced with the same tire and tire line. The failure recurred 5 months later. The vehicle was taken to the initial dealer where the tire was replaced with the same tire and tire line. The contact stated that the failure recurred 3 months later. The tire was not replaced. The manufacturer was not made aware of the failure. The vehicle failure mileage was approximately 2,815, and the tire failure mileage was approximately 2,815. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Engine · Fuel system, gasoline
The contact owns a 2022 Mercedes-Benz S580. The contact stated while driving 70 MPH, the vehicle lost motive power. The contact was able to veer to the side of the road. The contact stated that the failure reoccurred several times while driving. The check engine warning light was illuminated. The…
The contact owns a 2022 Mercedes-Benz S580. The contact stated while driving 70 MPH, the vehicle lost motive power. The contact was able to veer to the side of the road. The contact stated that the failure reoccurred several times while driving. The check engine warning light was illuminated. The vehicle was taken to the dealer, where the cam adjuster was replaced; however, the failure persisted. The vehicle was taken back to the dealer. The vehicle was not repaired. Additionally, the contact received notification of NHTSA Campaign Number: 23V445000 (Fuel System, Gasoline) however, the part to do the recall repair was not yet available. The manufacturer was notified of the failure and a case was opened; however, no further assistance was provided. The failure mileage was approximately 5,000.
- Power train · Suspension
The contact owns a 2022 Mercedes-Benz S580. The contact stated that while driving at an undisclosed speed, the vehicle vibrated violently. The low tire air pressure warning light was illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the front driver’s side tire. The…
The contact owns a 2022 Mercedes-Benz S580. The contact stated that while driving at an undisclosed speed, the vehicle vibrated violently. The low tire air pressure warning light was illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the front driver’s side tire. The contact was informed that bubbles had developed on the tire side wall, requiring a replacement. The vehicle was repaired, but the failure reoccurred. The vehicle was taken back to the dealer, who diagnosed an additional failure with the front driver’s side wheel requiring a replacement. The vehicle was repaired, but the failure reoccurred. The vehicle was taken back to the dealer, who determined that the vehicle required tire rebalancing. The vehicle was repaired, but the failure reoccurred. The vehicle was taken back to the dealer, who determined that the vehicle required an alignment. The vehicle was repaired, but the failure reoccurred. After investigating the failure, the contact related it to NHTSA Campaign Number 22V194000 (Suspension, Power Train), but the VIN was not included. The manufacturer was notified of the failure, and a case was opened. The failure mileage was 300.
- Tires
1. The tires//rims on this vehicle are causing extremely excessive tire blowouts. I have had at least 5 tire blowouts in the last 6 months alone along with 8-10 tire changes due to bubble forming on sidewall. This is a widespread issue on this vehicle in which I have read that many others are…
1. The tires//rims on this vehicle are causing extremely excessive tire blowouts. I have had at least 5 tire blowouts in the last 6 months alone along with 8-10 tire changes due to bubble forming on sidewall. This is a widespread issue on this vehicle in which I have read that many others are also experiencing the same. The vehicle is available for inspection. 2. A tire blowout while driving can be extremely hazardous especially on the freeway. 3. The problem with this vehicle has been confirmed with the dealer. However, they are unable to pinpoint what is exactly causing these excessive tire blowouts. 4. No, the vehicle has not been inspected. 5. No warnings prior to incidents.
- Engine · Fuel system, gasoline
The contact owns a 2022 Mercedes-Benz S580. The contact received notification of NHTSA Campaign Number: 23V445000 (Fuel System, Gasoline) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall…
The contact owns a 2022 Mercedes-Benz S580. The contact received notification of NHTSA Campaign Number: 23V445000 (Fuel System, Gasoline) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated while driving at an undisclosed speed, the vehicle stalled and inadvertently lost motive power with the check engine warning light illuminated. The contact stated that the vehicle was towed to the dealer to be diagnosed; however, the vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 4,000. VIN tool confirms parts not available.
- Electrical system · Engine · Power train
While driving on the freeway at approximately 40 mph on May 10, the yellow check engine light came on. I was approximately 200 miles into the current tank of gas, I stopped and checked to make sure the gas cap was properly secured. There were no obvious drivability issues. I immediately dropped the…
While driving on the freeway at approximately 40 mph on May 10, the yellow check engine light came on. I was approximately 200 miles into the current tank of gas, I stopped and checked to make sure the gas cap was properly secured. There were no obvious drivability issues. I immediately dropped the car off at Mercedes of Ontario, California, and they were able to confirm the problem, but could not clear the code, or determine the root cause of failure. Ontario Mercedes has now had my car for 6, days and that they are waiting for a M/B factory technician to tell them what to do.
- Service brakes
The contact owns a 2022 Mercedes-Benz S580. The contact stated that while driving approximately 50 MPH and entering the highway, the vehicle experienced an inadvertent brake failure. There was no warning light illuminated. The vehicle was taken to the local dealer where it was diagnosed and…
The contact owns a 2022 Mercedes-Benz S580. The contact stated that while driving approximately 50 MPH and entering the highway, the vehicle experienced an inadvertent brake failure. There was no warning light illuminated. The vehicle was taken to the local dealer where it was diagnosed and determined that a software update was needed. The vehicle was repaired; however, the failure persisted. The contact stated that on another occasion while driving approximately 15 MPH, the failure recurred. The contact was able to depress the brake pedal and then continued driving. The contact stated that several unknown warning lights became illuminated. The contact called the local dealer, but the vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 1,000.
- Electrical system · Forward collision avoidance › Automatic emergency braking · Service brakes
Was driver the car at 35 mph when the automated emergency breaks activated and made the car into a full stop. No cars or anyone was in front of the car. This happed again two days later doing about 30mph with no one around the car. Car had proximity 3000 miles My heads-up display stopped…
Was driver the car at 35 mph when the automated emergency breaks activated and made the car into a full stop. No cars or anyone was in front of the car. This happed again two days later doing about 30mph with no one around the car. Car had proximity 3000 miles My heads-up display stopped working on the car twice. First time it stopped the dealer had to order a new one and replace it. Same problem happed again after 2 month. Car lock does open when the car is running. I had a dad sitting the car and I came out with the keys with engine was running. The car locked itself and when pressed the unlock button on the key it doesn’t open. Have this problem multiple time.
- Forward collision avoidance › Adaptive cruise control
The contact owns a 2022 Mercedes-Benz S580. The contact stated that while driving at 30 MPH with the cruise control activated, the vehicle inadvertently accelerated due to the cruise control feature failing to recognize the correct speed limit sign. The dealer was made aware of the failure and…
The contact owns a 2022 Mercedes-Benz S580. The contact stated that while driving at 30 MPH with the cruise control activated, the vehicle inadvertently accelerated due to the cruise control feature failing to recognize the correct speed limit sign. The dealer was made aware of the failure and informed the contact to deactivate the cruise control feature. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 8,000.
- Forward collision avoidance › Automatic emergency braking
I was going at 70 miles without any car in the front and abruptly the break assistant activate , that happened twice , yesterday and today , and I am scare because instead of prevent an accident it will be causing one
- Forward collision avoidance › Automatic emergency braking
The contact owns a 2022 Mercedes-Benz S580. The contact stated while driving 35 MPH, the vehicle experienced phantom braking with the Active Brake Assist warning light illuminated. The contact stated that the vehicle operated normally after the failure. The dealer was contacted and the vehicle was picked up by a representative. The manufacturer was not contacted about the failure. The failure mileage was 6,003.
- Tires
I am an owner of a 2022 Mercedes Benz. The car is equipped with optional 21" AMG wheels paired with Pirelli P Zero MO-S (Mercedes original equipment) tires. P255/35R21 front and P285/30R21 rear. With only 490 miles on the odometer I experienced a catastrophic failure of the front passenger-side…
I am an owner of a 2022 Mercedes Benz. The car is equipped with optional 21" AMG wheels paired with Pirelli P Zero MO-S (Mercedes original equipment) tires. P255/35R21 front and P285/30R21 rear. With only 490 miles on the odometer I experienced a catastrophic failure of the front passenger-side tire after going over what seemed to be an insignificant pothole. While at the servicing dealer I noticed same car as mine with 21" wheels with a blown front driver-side tire and destroyed rim, I even took a picture of it. My service advisor confirmed that this is a very common issue that they see at least once or twice a month. That's in a city with maybe a 100 of these cars in total. "This should be a class action lawsuit" were his exact words. I had to wait over a week to get the car back as there is a nationwide shortage of this particular tire. My service advisor agreed that this also points to a higher than normal rate of failures that creates this shortage. I am an active member of the MBWorld.org forums where Mercedes owners come to discuss their vehicles. There are multiple threads about this very tire and a number of owners that experienced multiple failures, some as many as three times. It is common to have both the front and the rear tire fail after going over the same pothole, or in some instances the front tire failed while the rear developed a bubble and needed to be replaced as well. The only solution that people found was to replace Pirelli tires with Michelin Pilot 4S tires in the same size. I escalated this case to Mercedes-Benz Customer Advocacy and after several days was informed that Mercedes is not accepting responsibility for this faulty equipment and advised to seek resolution with Pirelli. This is clearly unacceptable and is not a matter of expenses or inconvenience. This is a huge safety risk as these tires seem to be either defective or unsuitable for such a heavy vehicle. At high speeds this could lead to fatal accidents.
- Seat belts
New 2022 S580 defective passenger seat belt buckle (female) fails to engage. Appears to be a manufacturing defect and/or poor quality control. Latch flange appears to be engaged even without seatbelt (male) buckle to restrain. Seatbelt therefore unusable. Additional risk that latch may not disengage and leave occupant trapped in seat unable to release buckle.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11010435Complaint -Check engine light(MIL) is ON. -Current and stored fault code in DCCU and PTCU : P2E9873 The position sensor of the exterior socket flap of the vehicle socket (direct current) has an electrical fault. The actuator does not open. -Starting the vehicle or Charging the vehicle is normal without any issues. Cause Software in the "N116/5 - Direct current charge connection unit (DCCU)" control unit. Remedy SW remedy for N116/5(DC-Charging control unit box) is in progress. Once the software is available, update the software for N116/5 and perform SCN coding of N116/5 For this issue, the vehicle starting or charging functions are not typically affected. Do not replace any parts. Replacing parts will not bring a solution for this issue.
- 11009204Complaint The flush-mounted door handle could jam when it is pulled out and may move in a jerky manner when doing so. In the area of the paneling section of the door, paint damage could be present (picture 1) and/or an abrasion point could be present at the door handle (picture 2). Cause The door handle could be installed too low in the y direction and/or the z direction (picture 3); as a result, the door handle could brush the door at the paneling section of the door. Remedy 1.) Loosen screws from bearing bracket (picture 4, step 1). 2.) Remove bearing bracket (see picture 4, step 2) from door. The door handle must be in pulled-in position. Open the affected door and push the door lock's rotary tumbler into the main catch. Lock the vehicle using the transmitter key so that the door handle is pulled in. Detach plug connector from bearing bracket (center slot). 3.) Paint over paint damage at door paneling (see picture 1) according to manufacturer specifications, using spot repair procedure if necessary. 4.) Loosen old assembly frame (picture 5, step 3). The assembly frame is bonded. Remove adhesive residue at front door. Bonding surfaces must be free of dust, oil, grease, wax, dirt residues and other adhesive components. Otherwise, this can lead to bonding problems. See "Parts" for part number of cleaning agent. 5.) Position new assembly frame (picture 5, step 3) at door. Remove protective film of tape at assembly frame beforehand. The assembly frame (picture 5, step 3) must have the same clearance all around the flange. 6.) Replace door handle, if an abrasion point (picture 2) is present. 7.) Screw in WITOL fasteners (picture 6) completely at mounting points of bearing bracket (picture 7, step 1) and align screws so that they are flush (picture 7, step 2). 8.) Position bearing bracket (picture 4, step 2). The door handle must have the same clearance all around in relation to the paneling section of the door (picture 8). 9.) Press the bearing bracket firmly against the paneling of the door and tighten the screws (picture 4, step 1) (=> torque: 6 Nm). 10.) Check the positioning of the bearing bracket. If necessary, loosen the screws slightly, readjust the bearing bracket slightly, then retighten the screws (=> torque: 6 Nm).
- 11009139Complaint When driving on rough ground, there may be noises from the 4-way head restraint of the front seats. The fault profile is not present at the limit stops (head restraint entirely retracted or entirely extended). Cause Head restraint has increased play between the worm and gearwheel in the head restraint mechanism. Remedy Check play/noise (see video attachment, headrest OK/headrest not OK). Please exchange the head restraint in the event of a not OK result.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11009036Complaint "Active Emergency Stop Assist Currently Unavailable" and "Active Steering Assist Inoperative" instrument cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.
- 11009025Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2018 - 2024 E-Class, S-Class & AMG GT (213, 217, 222, 223 and 290 platforms) vehicles, the low pressure fuel line does not meet current production specifications. Therefore, it is possible that accelerated aging in the area of connection could occur, resulting in a leak. A risk of fire can be ruled out. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will replace the braided hose of low-pressure fuel line and install a heat shield over the new braided hose.
- 11008977Complaint Combustion engine could no longer be started, only electric driving possible. Cause High-voltage belt-driven starter-alternator faulty. Remedy Requirement: Prior to the implementation of the test work, it must be ensured that the person carrying out this work has successfully completed the required HV qualification to work on HV system.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008080Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2024 S-Class and EQS (223 and 297 platform) vehicles, the DRIVE PILOT Supplemental Booklet does not correspond to current production specifications. What Were Doing MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the DRIVE PILOT supplemental booklet.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007966Complaint Display dark (total or partial) of one or more ASCM (AMG) steering wheel button displays - see attachment. Note: There is no loss of vehicle functionality due to this complaint. Cause Software can cause a partial display on the ASCM. Remedy Please perform the following steps in the event of a total or partial display of the ASCM displays: 1. Perform a hard reset (disconnect power supply) of control unit A74/2 (ASCM) for 2 minutes. 2. Perform a software update of the A74/2 (ASCM), N145 (DRVU) and A26/17 (HU). 3. Reset the user profile via the head unit settings menu. (Full factory reset)
- 11007960Complaint Vehicles with option code 200, DRIVE PILOT. "DRIVE PILOT cannot be activated system currently unavailable" on instrument cluster after pressing one of the DRIVE PILOT steering wheel activation button. Cause The instrument cluster message can be presented for multiple reasons. See "Remedy" section below. Remedy 1.Check for DTC's related to the system. If yes, process DTC. If no, proceed to 2. 2.If vehicle is low mileage or during a PDI, verify calibration of the short range radar sensors. Print control unit log of any Short Range Radar B29/11-14 (NBR-XX). Proceed to the bottom of the log, "Result of Calibration". Check "Alignment_quality XX" for each radar and confirm they are "Mature alignment". If all "Mature alignment" - Continue to step 3. If not all "Mature alignment" - Continue to "Calibration Process". Calibration Process Bring Xentry. Find a shopping center nearby that has a grid road, parking lots with reflective signs while safely being able to drive slow and make 90 degree turns are recommended. Park vehicle and key cycle twice. Drive at low speeds in the area for approximately 15 minutes. Complete 90 degree turns and pass reflective signs and parked vehicles when possible. Connect Xentry and print control unit log of any Short Range Radar B29/11-14 (NBR-XX). Verify if the radars are "Mature alignment". If yes, vehicle should be ready for DRIVE PILOT use. If no, begin process again with the park and key cycle. If after a second attempt the radars are not calibrated to "Mature". Try a different plaza. If radars still do not calibrate to "Mature", open a TIPS case. 3.Verify all system activation conditions are met as prescribed by the Owner's Manual and Drive Pilot Supplement. 4.If after verifying all short range radars have been calibrated and the system activation conditions are met yet the cluster message still appears, open a TIPS case.
- 11007796Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 110077311. Connect XENTRY Diagnosis. 2. Update Fuel System Control Unit (FSCU10) software. To do this, select menu item "Quick test view . N118/3 Control unit Fuel pump (FSCU10) . Adaptations . Control unit update . Updating of control unit software". Then follow the user guidance in XENTRY Diagnosis. 3. Disconnect XENTRY Diagnosis.
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11007673Complaint Damage or discoloration to paint protection films on vehicle. Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.
- 11006710Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class (206 platform), EQE (294 and 296 platform), EQS (295 and 297 platform), GLC (254 platform), AMG GT (192 platform), S-Class (223 platform), and AMG SL (232 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The communication module will receive an OTA software update that includes product improvements. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers will be mailed a letter informing them of this software update.
- 11006700Complaint Once the head unit A26/17 is updated to the FUP4 software release E445.0, it may be the case that online connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.
- 11006699Complaint Radio reception interference and the following DTCs are displayed in the A26/17 - MBUX multimedia system control unit as "active and stored": B19B313 - Antenna 1 open load B19B413 - Antenna 2 open load B19B513 - Antenna 3 open load B19B613 - Antenna 4 open load Cause Antenna amplifier Remedy Replace the antenna amplifier.
- 11006593Complaint The oil level is not correctly displayed while the instrument cluster display is in workshop mode. The oil level is reported in an inverted fashion when a correction is carried out. I.e. instead of an instruction to refill the oil quantity, an instruction to reduce the oil level is displayed, or vice versa. Cause Previous software release for instrument cluster control unit (N133/1) Boot software A2239049101, A2239046801, A2239040802 Remedy Update instrument cluster control unit (N133/1) software using XENTRY Diagnosis
- 11006547Complaint Customer states that wireless Apple Carplay does not initiate at start-up. The MBUX Display states "Apple Carplay could not be started. Your device has been connected as a bluetooth phone" Cause Previous MBUX Multimedia System (A26/17) software Remedy Update the MBUX Multimedia System (A26/17) software to version E330.x or newer.
- 11006545Complaint Yellow information message in driver display (instrument cluster): "Switch on motor to charge the 12V battery" Cause The state of charge (SOC) of the 12V battery has dropped to 45% or less. Remedy This warning message appears as soon as the state of charge (SOC) of the 12V primary battery drops below 45%. This message is displayed to safeguard the vehicle's starting ability. At the same time as the display appears in the instrument cluster, customers with a linked Mercedes me connect account also receive a push notification via the app/by email (if this function is activated). The battery must be charged to a state of charge (SOC) of at least 50%. To do this, an external charger can be connected (please comply with AR54.10-P-1133S) or the vehicle can be driven (by the customer) for 30 to 60 minutes. Please make customers aware of how the vehicle behaves: If the vehicle is used for short journeys, the battery state of charge may slowly drop to less than 45% a negative charge balance A negative charge balance will also occur if the vehicle is used while stationary without running the engine, e.g. if the head unit is used, the ignition is switched on, or other comfort & convenience power consumers, e.g. seat heating/seat ventilation, are active. An unlocked vehicle may increase consumption, because certain vehicle functions are actively kept ready for the customer. In combination with Keyless-Go or flush-mounted door handles, the vehicle may be woken up if the vehicle key is detected in the vicinity of the vehicle. The cause of the discharge can be identified with the aid of the onboard electrical system data in the EZS using XENTRY Diagnosis. See attached examples for identifying typical customer situations (e.g. operation with ignition on, operation of head unit while stationary or vehicle unlocked while parked).
- 11006544Complaint Vehicle not AC charging. Check engine light on. PTCU/N127 with fault code P0D9100 "The lock for the charging cable has an open circuit". Cause Possible Hardware and/or Software. Investigation is ongoing. Remedy Please open TIPS case. TIPS case: Needed customer feedback: When did the complaint/IC message occur? While driving and /or charging / or parking? If the complaint occurred while charging, how long after did the complaint/IC message occur? Which charging station was used, which provider (picture if possible)? Attach HV CUL and QT to the case Attach picture of label of AC charger to the case Attach screenshot of AV AC charger Provide the results of the test below Test: Verify AC charging Erase fault codes and verify if fault code P0D9100 The lock for the charging cable has an open circuit returns Check AV of AC charger
- 11005350Complaint Child seat detected message is shown in the central display and no child seat is installed on the front passenger seat at the time the display message is shown. Cause In certain circumstances, the gesture recognition system may interpret the occupancy status as a child seat present. The following possible conditions may lead to this: 1. Front passenger seat occupied by passenger 2. Object on front passenger seat, e.g. bag or backpack 3. Front passenger seat not occupied The gesture recognition system uses optical imaging to assess the front passenger seat and whether it is occupied and is independent from the occupant classification system input used for airbag deployment. The gesture recognition assessment has no connection to the airbag system. As this is an optical measurement, in certain circumstances a child seat message may be displayed based on the results of the interpretation. There is no influence on airbag system. There is no connection to airbag system. Remedy Software update of control unit N168 - Gesture recognition system OMSH223
- 11005349Complaint Vehicle not AC charging. Check engine light on. PTCU/N127 with fault code P0D9100 "The lock for the charging cable has an open circuit". Cause Possible Hardware and/or Software. Investigation is ongoing. Remedy Please open TIPS case. TIPS case: Needed customer feedback: When did the complaint/IC message occur? While driving and/or charging? If the complaint occurred while charging, how long after did the complaint/IC message occur? Attach HV CUL and QT to the case Attach picture of label of AC charger to the case Attach screenshot of AV AC charger Provide the results of the test below. Test: Verify AC charging Erase fault codes and verify if fault code P0D9100 The lock for the charging cable has an open circuit returns Check AV of AC charger Test with different charging station
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005337Complaint Mercedes me connect services inoperative (me-Call, Remote Status, etc.). Mercedes me services - activation not possible Notes: - The event code "B129C00 - Malfunction in control unit for telematics services" is active and stored - The head unit shows no internet connection Cause Under analysis. Remedy Please create a TIPS case, attach a RAMSES control unit log to the case.
- 11005336Complaint Digital light pop-up messages (warnings, notes, spotlight and dyn. low beam) appear in the instrument cluster (picture in attachment), even though the same digital light settings are stored in all MBUX profiles Note: The pop-up messages are intended to indicate different settings when changing MBUX profiles Cause - ECU software error Remedy - Reset MBUX to manufacturer default settings. Software update expected to be available YoM24/2 (Year of Modification - Code can be found in VeDoc): - A26/17 - MBUX multimedia system (head unit) -This document will be updated when the software is available.
- 11005334Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005315Complaint The oil level is not correctly displayed while the instrument cluster display is in workshop mode. The oil level is reported in an inverted fashion when a correction is carried out. I.e. instead of an instruction to refill the oil quantity, an instruction to reduce the oil level is displayed, or vice versa. Cause Previous software release for instrument cluster control unit (N133/1) Remedy Update instrument cluster control unit (N133/1) software using XENTRY Diagnosis
Every Mercedes-Benz S 580 4MATIC model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.