2013 MINI Clubman

Owner complaints

What owners report most

1. Electrical system7
2. Exterior lighting3
3. Unknown or other3
4. Air bags2
5. Engine2
6. Service brakes2

Latest complaints

• Mar 24, 2026NC
  Air bags · Electrical system · Service brakes
  Vehicle: MINI Cooper Clubman (Model R55) VIN: [XXX] Recall: NHTSA 23V-337 Dealer: Flow MINI of Raleigh, NC 1. COMPONENT FAILED: The Junction Box Electronics (JBE) failed due to moisture/water intrusion, producing electrical fault codes across all core systems including airbags, brakes, and a JBE…

  Vehicle: MINI Cooper Clubman (Model R55) VIN: [XXX] Recall: NHTSA 23V-337 Dealer: Flow MINI of Raleigh, NC 1. COMPONENT FAILED: The Junction Box Electronics (JBE) failed due to moisture/water intrusion, producing electrical fault codes across all core systems including airbags, brakes, and a JBE communication fault. The vehicle is located at Flow MINI of Raleigh and is available for inspection. 2. SAFETY RISK: Recall 23V-337 identifies that moisture intrusion into the JBE can lead to corrosion, short circuit, and in rare cases a thermal event (fire). My vehicle's carpet is wet, confirming active water intrusion into the footwell where the JBE is installed. Airbag and brake faults appear exclusively when it rains or when the vehicle is washed, directly and unambiguously linking all symptoms to water intrusion. The vehicle is currently unsafe to operate. 3. DEALER CONFIRMATION: Flow MINI of Raleigh confirmed moisture/water intrusion is causing the JBE faults — directly reproducing the failure during a dealer-performed wash. The dealer declined the recall repair solely because [XXX] is not listed among covered states. 4. MANUFACTURER RESPONSE: MINI USA denied coverage exclusively on the basis that North Carolina is not included in the recall's geographic region. The defect itself has not been disputed. 5. BASIS FOR COMPLAINT: The recall's geographic restriction was established based on road salt usage. North Carolina roads do receive road salt treatment during winter weather events. The recall documentation (RCRIT-23V337-7125.pdf, Page 4, Item 12) explicitly names the JBE as a covered component. I request that NHTSA: (1) treat this as urgent given confirmed airbag and brake faults, (2) review whether NC should be included in the recall's geographic scope, and (3) compel MINI USA to perform the recall repair on VIN [XXX] at no cost. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• Jun 2, 2025NY
  Air bags
  The 'Passenger air bag off' alert recurs without apparent cause, suggesting a system malfunction. I took my vehicle to a MINI dealership for evaluation, only to be informed that this is a known issue requiring replacement of the entire system at a cost of $1,800 + tax. Online research reveals that…

  The 'Passenger air bag off' alert recurs without apparent cause, suggesting a system malfunction. I took my vehicle to a MINI dealership for evaluation, only to be informed that this is a known issue requiring replacement of the entire system at a cost of $1,800 + tax. Online research reveals that many MINI owners with similar models face this safety issue. Given the severity and prevalence of this problem, I respectfully request that your agency consider ordering a recall for affected vehicles to ensure a free and safe repair."

• May 20, 2025AL
  Electrical system · Exterior lighting · Unknown or other

  Footwell module failure. No longer have turn signals, brake lights, power windows, dash lights, etc. When it rains, all warning lights go off and on continuously until it dries out.

• May 14, 2025AL134,000 mi
  Electrical system
  The contact owns a 2013 Mini Cooper Clubman. The contact stated that several unknown warning lights were occasionally remain illuminated while it was raining and while the vehicle was being washed, simultaneously causing the brake lights, turn signals, power windows, and other electrical components…

  The contact owns a 2013 Mini Cooper Clubman. The contact stated that several unknown warning lights were occasionally remain illuminated while it was raining and while the vehicle was being washed, simultaneously causing the brake lights, turn signals, power windows, and other electrical components to malfunction. The local dealer was contacted; however, the vehicle was not diagnosed. The contact was informed that the VIN was not under recall. The vehicle was not repaired. The contact referenced NHTSA Campaign Number: 23V337000 (ELECTRICAL SYSTEM); as a possible cause for the failure. The manufacturer was notified of the failure. The approximate failure mileage was 134,000.

• Sep 16, 2024WV
  Electrical system · Exterior lighting
  Car is not starting when sitting over night or parked at a lot. Windows will not roll down. Blinkers will not work. Difficulty when transporting my special needs child places as it is difficulty when car will not function as it should. Near accidents have almost occurred due to blinkers not…

  Car is not starting when sitting over night or parked at a lot. Windows will not roll down. Blinkers will not work. Difficulty when transporting my special needs child places as it is difficulty when car will not function as it should. Near accidents have almost occurred due to blinkers not working. I have been told by two different mechanics after diagnostic that the Foot Wheel Module is the problem identified.

• Jul 2, 2024NY
  Electrical system
  The contact owns a 2013 Mini Cooper Clubman. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable…

  The contact owns a 2013 Mini Cooper Clubman. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

• Apr 17, 2024MI130,000 mi
  Electrical system
  The contact owns a 2013 Mini Cooper Clubman. The contact stated that while driving at an undisclosed speed, the headlight failed to illuminate and the turn signals failed to engage. Additionally, the contact stated that the interior lights failed to turn off causing the battery to drain. The…

  The contact owns a 2013 Mini Cooper Clubman. The contact stated that while driving at an undisclosed speed, the headlight failed to illuminate and the turn signals failed to engage. Additionally, the contact stated that the interior lights failed to turn off causing the battery to drain. The vehicle was taken to an independent mechanic, where it was diagnosed with electrical system failure. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System); however, the part to do the recall repair was not yet available. The dealer was contacted.  The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure . The failure mileage was 130,000. VIN tool confirms parts not available.

• Mar 13, 2024SC52,747 mi
  Exterior lighting › Back up lights
  The contact owns a 2013 Mini Cooper Clubman. The contact stated that the driver’s side backup light was inoperable. No warning light was illuminated. The vehicle was taken to a local mechanic who performed a diagnostic test and stated there was a failure with the driver’s side backup light, and a…

  The contact owns a 2013 Mini Cooper Clubman. The contact stated that the driver’s side backup light was inoperable. No warning light was illuminated. The vehicle was taken to a local mechanic who performed a diagnostic test and stated there was a failure with the driver’s side backup light, and a defective footwell module. The vehicle was not repaired due to the cost. The manufacturer was not made aware of the failure. The approximate failure mileage was 52,747. The contact stated the defective footwell module was a recall and never informed of the recall.

• Jan 5, 2024FL
  Unknown or other

  UNKNOWN I was informed in July about the recall for my vehicle for the footwell control module. I have since taken my car in twice, the most being December 22, and they informed me that the fix for the recap was still not available. The recall was initially issued in May of last year, so it has been almost 8 months without being able to resolve the recall.

• Oct 10, 2020CA77,000 mi
  Engine

  Please refer to uploaded document

• Oct 5, 2020CA77,000 mi
  Engine · Unknown or other
  Driving down 680 from berkeley, ca at around 2:30pm: I was heading home and temperature light appears on dash. I notice it and try to pull off freeway trying to get to safe area to stop. before I could pull over to safety, the car stopped running (engine shut off). immediately steam was coming…

  Driving down 680 from berkeley, ca at around 2:30pm: I was heading home and temperature light appears on dash. I notice it and try to pull off freeway trying to get to safe area to stop. before I could pull over to safety, the car stopped running (engine shut off). immediately steam was coming from engine compartment and I could not get engine to start again. I called tow truck and the car was towed to pleasanton, ca MINI dealership/service department. I was unaware that MINI had extended the temperature housing part of engine to 10 year warranty due to the part being faulty. the first and last time the temperature guage warning light appeared was the last time I was able to start or drive the car! no warning.... None! the car overheated and destroyed the engine requiring a new engine that will cost more that the car IS worth. the car IS a 2013 MINI clubman and the temperature housing part of engine IS still under warranty. I was driving in the slow lane of the freeway and if I had not been, the car would have stalled in the middle of freeway! I or someone else could have been killed. the part IS a known defect yet the only remedy from MINI corporation was to extend warranty from 3 years to 10 years. That did nothing for me. I had no warning, no light, no nothing to make me aware that the car was going to get so hot that the engine would fail nearly immediately. the faulty temperature housing part should have been recalled rather than extend warranty. again, I was on freeway and no warning indicating the engine was getting dangerously hot. Not only a safety issue but clearly an issue for the engine and car being worthless due to engine failure. we regularly get the car serviced and have taken care of the engine and car. the last time it was serviced was march 2020 and this occurred october 2020.

• Jan 4, 2019LA52,000 mi
  Electrical system
  Ignition coil failed causing vehicle to disable while moving on a 4 lane parkway. There IS a "limited warranty extension" on this part (the ignition coil) for this make and model, suggesting that a defect IS known, but it has not been declared a recall (yet) the part failing blew the fuse for…

  Ignition coil failed causing vehicle to disable while moving on a 4 lane parkway. There IS a "limited warranty extension" on this part (the ignition coil) for this make and model, suggesting that a defect IS known, but it has not been declared a recall (yet) the part failing blew the fuse for the coil circuit and also took out the vehicle's electronic control unit, causing thousands of dollars in damage, for which the manufacturer only consider the ignition coil to be covered under the extended warranty. this part failing caused an extremely unsafe situation in that my vehicle completely disabled blocking a lane of traffic. I then waited in the rain for nearly 2 hours on new year's eve for a tow truck. I want others to know that this part can potentially fail to hopefully keep them from having this situation. I am still waiting for invoice from repair shop but will upload it later.

• Jan 27, 2014CA8,749 mi
  Service brakes
  I have a 2013 MINI clubman s with only 8K miles on it. as I started it today and was driving out of my garage the brakes would not function as the brake pedal was very hard, (like stepping on a brick) and was unable to bring the car to a stop using the brake pedal? luckily I was able to stop the…

  I have a 2013 MINI clubman s with only 8K miles on it. as I started it today and was driving out of my garage the brakes would not function as the brake pedal was very hard, (like stepping on a brick) and was unable to bring the car to a stop using the brake pedal? luckily I was able to stop the car with the parking brake lever before I hit anything... (Thank god my wife wasn't driving...) as it, of course IS still under warranty it IS going into the dealer tomorrow, but they claim "they have never herd of this problem"? this was very frightening and am now concerned about a recurrence of the brakes failing again and causing a serious accident if it were to reoccur on the highway and higher speeds... The car, (brakes) were functioning properly when I parked the car in the garage the night before... I'm confident the dealer will correct the problem, but I'm very unnerved by the implications of this incident... *tr

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 10250379Customers with a genuine MINI Click and Drive System (C&D) accessory installed may complain of steering system check control messages (CCM) and reduced steering functionality. The concern starts after a software update to 4.28.1.x (21-03-500) or greater, and the issue can be duplicated after placing a device on the MINI (C&D) Click and Drive accessory. One or more of the following CCM may be stored: Steering effort increased Driving Stabilization failed Speed control failed Collision warning failed Pedestrian warning failed
• 10249431Customer complains of a musty odor or damp front footwell carpet.
• 10245428Cavity protection applied to underside of the hood is leaking out onto the wheel arch trim and grille.
• 10244507MINI electrical systems have continued to develop over the past few years. As a result, the demand on the batteries has increased. Breakdowns due to an empty battery or problems in the vehicles electrical system can have various causes, most of which are not due to the battery itself. For this reason, a battery replacement will permanently eliminate the problem only in the rarest of cases. The energy diagnosis test module helps to localize these causes. This document covers important information for the dealer on how to handle discharged battery complaints. Without performing the energy diagnosis test plan, the root cause of a discharged battery cannot be identified. In order to properly repair the vehicle the first time, it is very important that the diagnostic test plan is performed to completion; with all results taken into consideration.
• 10216784XM Satellite Radio Recekption - Audio, Navigation, Monitors, Alarms, SRS
• 10206696New RDC wheel electronics will be introduced with future generation MINI models. The new wheel electronics are identified as Huf Generation 5. These new wheel electronics will need to be programmed using the new tool when replaced or when depressurized (0 psi) for more than 2 minutes.
• 10179827OC3 SEAT OCCUPANCY MAT - LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES: Component-Specific Limited Warranty Extension For the above-referenced vehicles, MINI USA, a division of BMW of North America, LLC (MINI USA) is extending the limited warranty for the front passenger's OC3 seat occupancy mat (shown) to: 10 years/120,000 miles as determined by the vehicle's original in-service date.
• 10160298N18 THERMOSTAT WITH THERMOSTAT HOUSING: LIMITED WARRANTY EXTENSION TO 10 YEARS/ This Service Information bulletin supersedes SI M01 02 18 dated May 2018.
• 10160229N18 THERMOSTAT WITH THERMOSTAT HOUSING: LIMITED WARRANTYEXTENSION TO 10 YEARS/ This Service Information bulletin supersedes SI M01 02 18 dated May 2018.
• 10153778OC3 seat occupancy mat: limited warranty extension to 10 years/120.
• 10152680"MANUAL TRANSMISSION - STIFF DIAGONAL GEARSHIFT LEVER MOVEMENT. The customer may complain of a ""stiff diagonal shift"" (e.g., N-R, R-N, 2-3/3-2 or 4-5/5-4). Also, in some cases, gears cannot be selected, or the selector gear does not go into the neutral position. CAUSE 1. The deflection lever circlip of the gearshift mechanism is damaged or missing. 2. Possible corrosion at the gearshift mechanism (shift cables or transmission gearshift unit)"
• 10152359N18 Engine: FC 37DE Engine Ventilation, Heating, Triggering Stored in the DME After Programming. The Service Engine Soon lamp is illuminated after reprogramming the vehicle to integration level R056-11-11503 (ISTA/P P45.1.3.0) or higher. When diagnosed, the following fault code is stored in DME fault memory: ??37DE Engine ventilation, heating, triggering: open circuit CAUSE Due to a DME software change, the diagnostic monitoring capability is improved for the engine ventilation heating system. However, a fault will be stored in the fault memory because the engine ventilation heater circuit has a malfunction currently present.
• 10152335Brake Fluid Maintenance Service: 36-Month Interval. The CBS displays the first brake fluid service as a 36-month interval from the date of production, instead of the appropriate 24-month interval. Only vehicles within the specified production range can be serviced and covered by this bulletin. For vehicles outside of the production range specified in this bulletin, refer to the CBS and/or Key Read information for the brake fluid service.
• 10151423CAS Module Fails Programming with CoAPI Error 2082. During vehicle programming, the CAS (Car Access System) module fails to program with CoAPI error 2082 displayed. Refer to the attachment, which lists the affected CAS serial numbers. The following part numbers are affected: 61 35 9 287 534 61 35 9 226 238 61 35 9 227 053 61 35 9 287 535
• 10151349Bluetooth Connection Failures This Service Information bulletin supersedes SI M84 01 14 dated February 2016.. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware
• 10151347Delay in Automatic Driving Light Switching on/off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes. Shut-off period varies based on detected situation. This is normal operational behavior.
• 10151060This Service Information bulletin supersedes SI M84 01 14 dated November 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: z Apple iPhones z Samsung S6 and the S6 Edge. Connectivity failure examples are: z Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. z Contact List incomplete z General connection failures z Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) z Samsung S6 and S6 Edge device firmware
• 10150985?OC3 SEAT OCCUPANCY MAT: LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES. This Service Information bulletin supersedes SI 01 11 16 dated December 2016.
• 10150399"Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a ""Service Engine Soon"" lamp being illuminated."
• 10150357?SUBJECT DWA (Anti-theft Alarm System): False Alarm Is Triggered Intermittently. When the vehicle is parked and locked (DWA active), the alarm system is triggered intermittently. One or more of the following conditions may trigger the alarm system: Sun roof in the tilted/open position, Window partially open, Excessive local noise (for example, near an airport, on a busy road, or in heavy rain) CAUSE Normal sensitivity of the interior ultrasonic sensor.
• 10150356"Discharged Battery: Energy Diagnosis Must Be Performed. MINI electrical systems and advancements in vehicle technology have resulted in an increased demand on the vehicle battery. This SI will help the dealer handle ""discharged battery"" complaints. A discharged battery can have various causes, most unrelated to the battery. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to http://www.batteryuniversity.com/parttwo-42B.htm. For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. To properly repair the vehicle the first time in the workshop, the diagnostic test plans must be performed to completion, with all results taken into consideration. The procedure below will guide the technician to properly repairing the vehicle and getting paid for a warranty claim. CAUSE Discharged battery."
• 10150353"Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a ""Service Engine Soon"" lamp being illuminated."
• 10150352"Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a ""Service Engine Soon"" lamp being illuminated."
• 10150351"Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a ""Service Engine Soon"" lamp being illuminated."
• 10150347During Engine Oil Service a Small O-Ring Is Found in the Oil Filter Housing. No customer complaint has been received. During the scheduled engine oil service, the technician notices a black rubber o-ring lying on the bottom of the engine oil filter housing. The o-ring has been dislodged from the non-return valve inside the engine oil filter housing. No subsequent engine damage occurs from the dislodged o-ring. Engine oil filter housing (1) Rubber o-ring (2) The material dimensions of the rubber o-ring are not satisfactory, allowing it to become dislodged from its installation location.
• 10150309Squeaking Noise from Front Seat. A noise may be heard from the front driver's seat back when the customer applies sideways pressure during cornering. CAUSE Surface corrosion on the metal seat back frame can make a squeaking noise when rubbing against the foam rubber padding of the seat back.
• 10150306"Erroneous ""Service due"" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness."
• 10150305Adjusting Rear Camber. Rear camber cannot be adjusted properly. CAUSE Repair instructions not followed properly
• 10150269Intermittent Humming or Buzzing Noise from Speedometer. When the vehicle is decelerating, an intermittent humming or buzzing noise coming from the instrument cluster may be heard when the speedometer needle is between 0 and 12 mph. Hardware error in the instrument cluster
• 10150268Battery Charge Condition Not Available in Energy Diagnosis. When performing an Energy Diagnosis test plan, the battery charge condition information is not available. CAUSE The power management system was not reset properly at the end of vehicle production, leaving the IBS in a failsafe mode.
• 10150241Incorrect Customer Relations Telephone Number Is Saved in the Vehicle. The customer is not connected to MINI Customer Relations after dialing the number displayed in the vehicle Kombi or radio. CAUSE During the Pre-Delivery Inspection (PDI), the incorrect telephone number is being written into the vehicle. INFORMATION 1. When performing the PDI test plan, it is extremely important that you select MINI if the ISID is configured for both BMW and MINI. 2. After completion of the PDI test plan, verify that the customer relations number stored in the vehicle is correct. 3. The correct customer relations phone number is 1(866) 275-6464. 4. If the number stored in the vehicle is incorrect and the correct test plan was used, contact your 3g Administrator and have him or her verify the number stored in the ISID. 5.This picture shows the correct number stored in the Combox control unit. Note: To read out telephone number:
• 10150238"N14 and N18 Engine: High-pressure Pump Repair Instruction. INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, ""Removing and installing or replacing high-pressure pump (N14, N18)"" has a procedure error. The current version of the Repair Instruction states to replace the highpressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15601.2.M130113... 8/30/2013 Page 2 of 2 All vehicles equipped with the N18 engine and produced from 3/2012 and later. When the engine is fitted with a Bosch High-pressure Pump (1) the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightning torques are correct. Refer to EPC for the applicable part numbers when making repairs. "
• 10150237?N18 Engine: FC 2BF2 Rail Pressure Sensor Is Stored in DME Fault Memory. The customer states that the Service Engine Soon lamp is illuminated and the following fault is stored in the DME: FC 2BF2 Rail pressure sensor, workspace: pressure too high CAUSE A DME calibration error in the fuel pressure diagnostics results in an increased sensitivity.
• 10150205"?SI M34 01 13 November 2013 BrakesTechnical Service This Service Information bulletin supersedes SI 34 01 13 dated October 2013. designates changes to this revision SUBJECT Erroneous ""Service due"" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness."
• 10150148Basic SVS: Voice Recognition Inoperative After Programming. After programming the vehicle with ISTA/P 2.48.x, the voice recognition (Basic SVS) is inoperative. NOTE: The Basic SVS only includes voice recognition for phone functions. Error in the coding data of ISTA/P 2.48.x The voice recognition function is unintentionally deactivated.
• 10150147"CHAMP2: Stored Radio Stations Deleted After Ignition Off. After ignition off, the stored radio stations (AM/FM and Satellite radio) are no longer available in: * Menu ""PRESETS"" * Preset buttons on the head unit Hardware error in the CHAMP2 head unit"
• 10150145Clutch Is Slipping or Grabbing. The customer states that the clutch is slipping or grabbing.
• 10150091"DWA (Anti-theft Alarm System): False Alarm Is Triggered Intermittently. INFORMATION Parts replacement will not solve the problem if one or more of the conditions described in the situation above caused the alarm to trigger. The sensitivity of the interior ultrasonic sensor cannot be reduced. If the customer wishes to park the vehicle with the sunroof tilted, the window partially open, and/or in an area with excessive local noise, the interior sensor must be switched off by using the following procedure: Press the lock button on the remote control twice in succession. The LEDs flash in short succession for approx. 2 seconds. The interior ultrasonic sensor is switched off until the vehicle is unlocked and locked the next time. NOTE: This information can be found in the Owner's Manual in the ""Controls"" section under ""Switching off the tilt alarm sensor and interior movement detector."""
• 10150090"HAMP2: Stored Radio Stations Deleted After Ignition Off. After ignition off, the stored radio stations (AM/FM and Satellite radio) are no longer available in: * Menu ""PRESETS"" * Preset buttons on the head unit Hardware error in the CHAMP2 head unit"
• 10150088"PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. SUBJECT Service Action: Retrofit of Engine Coolant Temperature Sensor. Internal corrosion can form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading can lead to difficulty in the engine starting and/or a ""Service Engine Soon"" lamp being illuminated."

Every MINI Clubman model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.