Temsa global (temsa) IS recalling certain model year 2007-2012 TS35 buses for failing to comply with the requirements of federal motor vehicle safety standard no. 217, bus emergency exits and window retention and release. some of the emergency exit mechanism instruction labels may have been installed farther than 16 cm from the release mechanism.
Risk and remedy
Risk
Due to the distance between the operating instructions and the windows release mechanism, in the event of an emergency, passengers may not recognize and follow the instructions for releasing the emergency exit windows delaying their safe exit from the bus and , increasing the risk of personal injury.
Remedy
Temsa will notify owners, and new labels will be mailed to owners free of charge. the safety recall IS expected to begin on or before may 23, 2012. owners may contact temsa at 1-404-602-0151.
Temsa global (temsa) IS recalling certain model year 2011-2012 TS35 buses for failing to comply with the requirements of federal motor vehicle safety standard no. 121, air brake systems. the anti-lock brake system (ABS) malfunction warning indicator does not illuminate in a check lamp function when the ignition IS turned to the on or run position.
Risk and remedy
Risk
Without the check lamp feature, the driver may not be aware that the indicator lamp IS not working properly, and if there were an ABS problem, the driver would not receive a warning. a malfunctioning anti-lock brake system may increase the risk of a crash.
Remedy
Temsa will notify owners, and dealers will repair the buses free of charge. the safety recall began on march 15, 2012. owners may contact temsa at 1-407-601-7801.
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
10186878This bulletin defines alignment specifications of the TS35 vehicle. Alignment of TS 30.
10186278Bathroom lock latch bolt
10185889FIRE INSTRUCTIONS: Actions to Be Taken In The Event Of a Fire.
10185885New flap is to be installed in fuel tank filler cap
10185884New flap is to be installed in fuel tank filler cap
10185883Relocating Transmission Oil Dipstick
10185882Following document shows how to set tag axle steering system cylinders and bleeding the tag axle steering system
10184238Alignment Sepcifications of TS35. This bulletin defines alignment specifications of the TS35 vehicle.
10183910Information Document sheet.
10183888Preventing fuel leaking out
10183887Preventing fuel leaking out
10183886Relocating transmission oil dipstick.
10183885Instructions on how to set tag axle steering system cylinders and bleeding the axle steering system.
10183856Vehicle Schematics
10183855Temsa Non Exclusive Authorised Service Center Agreement
10183854TS 35 Epa13 Wiring. Refer to Section 6 and Section for hardware pin-out of MOKI, ZR32, MULTIPLEXERS, and CAN lines. As the multiplex unites are controlled by special algorithm, in case needed, the latest vehicle program should be downloaded from online system E-DOC.
10128114ZF Service Information Bulletin for retrofitting seal carrier and readjustment of king pin
10056629Temsa: information explaining the installation of the ventilation hose. Model TS35.
10056006Temsa: information provided regarding the replacement of hydraulic hoses in some buses.
10053765Temsa: information provided regarding the installation of an expansion tank modification. Model ts 35. No years.
10045882Temsa: information provided regarding the torque value for intercooler clamp improvement. Model TS-35. No model years listed.
10044446Temsa bus: when ignition IS off or key switch IS removed, door control switch can not be use. A new relay flasher buzzer sound under dashboard will be installed. Modification to door control switch inside bus allows usage when ignition IS off or key switch IS removed.
10043256Temsa: on some model buses, there IS an issue with low voltage charge modification on the alternator.
Every Temsa TS35 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.