2013 Toyota Prius C

Owner complaints

What owners report most

1. Electrical system23
2. Service brakes16
3. Engine7
4. Unknown or other5
5. Fuel/propulsion system5
6. Hybrid propulsion system5
7. Air bags4
8. Exterior lighting4
9. Power train4
10. Vehicle speed control4

Latest complaints

• Aug 28, 2026AZ
  Electrical system · Power train · Vehicle speed control
  While I was driving on the freeway the dash lit up with multiple lights. Simultaneously, I lost power to the car and could not accelerate and only break. The steering was tight and I could not steer correctly. Then a message that said, CHECK HYBRID SYSTEM STOP THE VEHICLE IN A SAFE PLACE…

  While I was driving on the freeway the dash lit up with multiple lights. Simultaneously, I lost power to the car and could not accelerate and only break. The steering was tight and I could not steer correctly. Then a message that said, CHECK HYBRID SYSTEM STOP THE VEHICLE IN A SAFE PLACE IMMEDIATELY. The was slowing down and I had to pull over on the side of the freeway. There were no fluids leaking from the car.The car did not power back on nor run for over 10 minutes. The incident put my safety and other safety at risk by turning off while driving highway speeds. I was afraid for my life. There is an open recall which has not yet been resolved Major Safety Recalls for the 2013 Prius •The Hybrid Inverter Module (Critical Recall): Excessive voltage inside the Intelligent Power Module (IPM) can cause the hybrid system to overheat, shut down completely, or put the car into "limp home" mode while you are driving.

• Feb 5, 2026CT150,000 mi
  Hybrid propulsion system
  The contact owns a 2013 Toyota Prius C. The contact stated that while his wife was attempting to cold-start the vehicle, the vehicle failed to start. The contact stated that on several occasions the vehicle was started; however, the instrument cluster and other electrical devices failed to operate…

  The contact owns a 2013 Toyota Prius C. The contact stated that while his wife was attempting to cold-start the vehicle, the vehicle failed to start. The contact stated that on several occasions the vehicle was started; however, the instrument cluster and other electrical devices failed to operate as needed. The contact replaced the auxiliary battery. The vehicle was repaired, but the failure reoccurred, and the vehicle needed to be jump-started. The vehicle was not taken to a local dealer or independent mechanic to be diagnosed or repaired. The contact researched online and related the failure to NHTSA Campaign Number: 20V369000 (Hybrid Propulsion System); however, the VIN was not included in the recall. The manufacturer was not informed of the failure. The failure mileage was approximately 150,000.

• Jan 23, 2026TX
  Electrical system · Service brakes

  Brake master cylinder failure.

• Jan 2, 2026CA
  Service brakes
  Car suddenly needed a jump start and again after a day or two of non-use. On the third day Brakes, ABS and traction control warnings were lighted up and remains. Brakes are mostly ineffective. My own scan returns the code C1252 and C1256 that says brake booster system failing. Took it to the dealer…

  Car suddenly needed a jump start and again after a day or two of non-use. On the third day Brakes, ABS and traction control warnings were lighted up and remains. Brakes are mostly ineffective. My own scan returns the code C1252 and C1256 that says brake booster system failing. Took it to the dealer who charged $290 again to scan and came up with failed brake booster and pump assembly. The dealers is quoting total $4000 to fix. Toyota Customer Support Program Bulletin dated 8/2018 and revised on 8/2019 extends the warranty on for this issue (for Toyota Prius C 2013) for 10 years or 150000 miles. I was never informed by Toyota or the seller (Stevens Creek Toyota, San Jose CA) about this defect under warranty that I could have gotten repaired well before the dead line of 10 years. Now Both Toyota or the dealer's service department refuse to bear the repair cost.

• Dec 20, 2025FL
  Service brakes
  Warning lamps for ABS and others and the chiming dings came on while pulling away from the bank drive through and parking for a second. I shut the engine off and turned back on with no success. I was barely able to park in a spot because of difficulties braking. My car had been making an electric…

  Warning lamps for ABS and others and the chiming dings came on while pulling away from the bank drive through and parking for a second. I shut the engine off and turned back on with no success. I was barely able to park in a spot because of difficulties braking. My car had been making an electric noise every 15 seconds or so previously, at different times when parked, but I thought it was the hybrid engine. Now I think it was the brake pump trying to build up pressure due to a faulty, leaking brake actuator.

• Oct 1, 2025TX
  Electrical system · Unknown or other
  My 2013 Toyota Prius has a failed inverter/converter assembly, including the Intelligent Power Module (IPM). This component is critical for vehicle operation and designed to last the life of the car. Premature IPM shorting and inverter failure is a known defect acknowledged by Toyota through…

  My 2013 Toyota Prius has a failed inverter/converter assembly, including the Intelligent Power Module (IPM). This component is critical for vehicle operation and designed to last the life of the car. Premature IPM shorting and inverter failure is a known defect acknowledged by Toyota through multiple recalls and service campaigns for other VINs with the same part number. My vehicle is giving codes P0A94 and P0A1A which are also listed in the recalls for other Prius models of similar age. My vehicle experiences the same failure, yet Toyota has denied goodwill coverage, claiming “insufficient service history.” Routine maintenance like oil changes and brake inspections does not affect this component, making the denial unreasonable. There is nothing to service on the inverter. This defect poses a serious safety risk, sudden inverter failure caused total loss of power while driving and loss of power steering, it was difficult to pull my car off the road. This poses a danger to drivers, passengers, and others on the road. Toyota’s exclusion of my VIN from coverage leaves me financially responsible for a known safety defect. I request NHTSA to investigate Toyota’s handling of inverter/IPM failures, the denial of goodwill assistance for affected VINs, and ensure that Toyota addresses this life-threatening defect consistently across all affected vehicles instead of narrowing the scope on who gets coverage when this is a dangerous electrical malfunction.

• Sep 3, 2025MA75,421 mi
  Hybrid propulsion system › Inverter
  The contact owns a 2013 Toyota Prius C. The contact stated that while driving at 25 MPH, the vehicle stalled and failed to restart. The contact stated that he and his wife were in the vehicle during the failure, and the vehicle was almost crashed into. The contact stated that he and his wife were…

  The contact owns a 2013 Toyota Prius C. The contact stated that while driving at 25 MPH, the vehicle stalled and failed to restart. The contact stated that he and his wife were in the vehicle during the failure, and the vehicle was almost crashed into. The contact stated that he and his wife were left stranded in oncoming traffic. The vehicle was towed to the dealer, where it was diagnosed that there was a computer failure and that the inverter converter assembly needed to be replaced. The vehicle was repaired. The manufacturer was notified of the failure. The failure mileage was 75,421.

• Jul 29, 2025FL
  Electrical system · Engine

  failure of the Intelligent Power Module (IPM) within the inverter assembly

• Jul 1, 2025GA
  Service brakes
  Recently the dash board lights started intermittently coming on. When they are on, the brakes do not work until pressed all the way to the floor and even then the car takes a long time to stop. The lights will randomly turn off and suddenly the car brakes work normally again. It is happening…

  Recently the dash board lights started intermittently coming on. When they are on, the brakes do not work until pressed all the way to the floor and even then the car takes a long time to stop. The lights will randomly turn off and suddenly the car brakes work normally again. It is happening intermittently with no rhyme or reason as to when it will happen. It's scary to drive because I dont know if the brakes will work or not and I almost ran into another car when trying to stop at a stop light. I took the car to be inspected at the Toyota service center for $190 and after inspection they said the brake booster and master cylinder assembly need to be replaced and it will cost $2300.

• Jun 19, 2025VA
  Service brakes

  Require replacement of brake booster pump, decreased braking ability

• Apr 3, 2025MICrash
  Air bags · Forward collision avoidance › Automatic emergency braking · Unknown or other
  There was a driver side collision and the airbags did not deploy. Brakes do not slowly apply they slam down causing vehicle to slide/skid in emergency braking, ABS does not function properly. The dealership recently did an appraisal (4/2/25) on the vehicle that states “Lost communication with side…

  There was a driver side collision and the airbags did not deploy. Brakes do not slowly apply they slam down causing vehicle to slide/skid in emergency braking, ABS does not function properly. The dealership recently did an appraisal (4/2/25) on the vehicle that states “Lost communication with side airbag sensor LH, Side airbag sensor LH initialization incomplete, front speed sensor RH & LH circuit, and D- Door Motor ECU communication stop”. Insurance company inspected vehicle after crash, and there was a police report filed. There were no warning indicators prior to incident or after.

• Dec 23, 2024OH
  Service brakes
  the vehicle exhibits several warning lights on the dash including ABS, VSC brake and handbrake. Diagnosed code as C1391 which toyota had released a bulletin to admit this issue, but they don’t make a recall instead of only repair it when occurred within their limited time line. now my vehicle…

  the vehicle exhibits several warning lights on the dash including ABS, VSC brake and handbrake. Diagnosed code as C1391 which toyota had released a bulletin to admit this issue, but they don’t make a recall instead of only repair it when occurred within their limited time line. now my vehicle falls in their bulletin scope but out of their “warranty “ scope. and quoted for thousands of repair. as a matter of fact, this put me at a great risk in driving it. and toyota didn’t make a public recall to solve this problem.

• Sep 14, 2024FL
  Service brakes
  Driving on the highway at 70mph my warning lights for my ABS, traction control, and other brake related warning lights came on. My brakes became soft and hard to stop the car. Immediately brought to dealer who said that my booster accumulator was leaking and needed to replace both the accumulator…

  Driving on the highway at 70mph my warning lights for my ABS, traction control, and other brake related warning lights came on. My brakes became soft and hard to stop the car. Immediately brought to dealer who said that my booster accumulator was leaking and needed to replace both the accumulator and pump for over $3,500. This is a know. Issue with Toyota because they have a service bulletin that they wouldn’t honor because my car is more than 10 years old. This is a serious issue and someone is going to get badly hurt.

• Sep 14, 2024MACrash
  Electrical system · Service brakes · Steering
  Immobilized failure due to combination of brake hose failure preventing hybrid control/shift actuator. Hybrid steering lock became disengaged and could not communicate with the certification ecu due constant power being disabled due to complete main body failure. Hybrid system cannot go back into…

  Immobilized failure due to combination of brake hose failure preventing hybrid control/shift actuator. Hybrid steering lock became disengaged and could not communicate with the certification ecu due constant power being disabled due to complete main body failure. Hybrid system cannot go back into park however ecm side did. Ecm was not receiving power as dealer coded main body as a plug in hybrid effectively disabling fuel systems (including emissions/fuel safety) causing full misclassification in the smart key certification process. Car starts, goes into ready and disables LIN comms alongside cutting main relay due to tailgate and fuel constant powers being cut while driving.

• Aug 12, 2024FL133,000 mi
  Service brakes, hydraulic · Traction control system
  The contact owns a 2013 Toyota Prius C. The contact stated while driving approximately 5 MPH and pulling out of the driveway, while attempting to depress the brake pedal, excessive amount of force was needed to depress the brake pedal. The contact stated that the braking distance was extended, and…

  The contact owns a 2013 Toyota Prius C. The contact stated while driving approximately 5 MPH and pulling out of the driveway, while attempting to depress the brake pedal, excessive amount of force was needed to depress the brake pedal. The contact stated that the braking distance was extended, and the vehicle was jerking while stopping. The contact stated that the ABS, Brakes, and traction control warning lights were illuminated. The vehicle was taken to the dealer to be diagnosed. The contact was informed that the hydraulic brake booster pump actuator and accumulator had failed and needed to be replaced. The dealer confirmed related the failure to Customer Satisfaction Program under NHTSA ID Number: 10181735 (Equipment Adaptive/Mobility, Equipment, Service Brakes) however the vehicle was no longer covered for the repair. The vehicle had not been repaired. The manufacturer was made aware of the failure and confirmed that the vehicle was not included in the Customer Service Program. The manufacturer referred the contact to the NHTSA Hotline to report. The failure mileage was 133,000.

• Jun 26, 2024VA
  Exterior lighting

  Head low beam lights no work

• Feb 15, 2024CA
  Service brakes
  I purchased this car July 14th 2023 from a dealership that wasn't Toyota for my daughter to go back and forth to school and as soon as we drove off the lot all kinds of lights came on I called the dealership asked what they were he acted like he didn't know what I was talking about so I've had it…

  I purchased this car July 14th 2023 from a dealership that wasn't Toyota for my daughter to go back and forth to school and as soon as we drove off the lot all kinds of lights came on I called the dealership asked what they were he acted like he didn't know what I was talking about so I've had it at a couple different shops finally Toyota looked at it the service manager let me know that there used to be a recall on the brake booster with master cylinder assembly and that that recall the extended warranty on it had expired I'm not sure how anything thats to do with safety expires when it's regarding your braking

• Aug 16, 2023CA
  Fuel/propulsion system · Vehicle speed control

  I was going on my way to work on the freeway at approximately 65 miles per hour, suddenly I felt as if my car shut off will driving and I lost power. I pressed on the gas Pedal as I was pulled into the emergency lane to the right of the freeway, the gas pedal did not work. I pulled to the side and I shut the car off. I waited about 20 minutes and I turned the car back on.

• May 31, 2023MA104,000 mi
  Hybrid propulsion system
  The contact owns a 2013 Toyota Prius C. The contact stated that while driving at an undisclosed speed, the check Hybrid Propulsion System warning light illuminated, and the vehicle the stalled. The vehicle was towed to the dealer to be diagnosed. The contact was informed that the inverter module…

  The contact owns a 2013 Toyota Prius C. The contact stated that while driving at an undisclosed speed, the check Hybrid Propulsion System warning light illuminated, and the vehicle the stalled. The vehicle was towed to the dealer to be diagnosed. The contact was informed that the inverter module needed to be replaced. The vehicle was not repaired. The VIN was not included in NHTSA Campaign Number: 20V369000 (Hybrid Propulsion System) and 18V684000 (Hybrid Propulsion System). The manufacturer was notified of the failure and a case was opened. The approximate failure mileage was 104,000.

• May 5, 2023CA
  Electrical system · Engine

  My vehicle has under 150,000 miles. I was driving on the highway and my Prius lost power and left me on the side of the road. I took it to Toyota to run a diagnostic in Elk Grove Ca. I was told the ipm inverter, control computer had to be replaced and it would cost me $5,200.00. This is a real disappointment because I don’t have this money to fix the vehicle.

• Feb 25, 2023CA
  Back over prevention › Warnings · Structure › Body

  A tree fell on my car during a storm. The tree remains on top of my car. Waiting for your party to remove it off of my car.

• Jan 9, 2023CA
  Electrical system · Power train
  According to Toyota Dealership, "WILL NEED TO REPLACE (MG1) HV TRANSAXLE UNIT AS 1ST STEP IN ORDER TO TO BE ABLE TO PROCEED WITH DIAGNOSE AND CHECKED FOR ANY OTHER SHORTED COMPONENTS". Vehicle is available for inspection. Vehicle was being driven on a city street towards a red light when the…

  According to Toyota Dealership, "WILL NEED TO REPLACE (MG1) HV TRANSAXLE UNIT AS 1ST STEP IN ORDER TO TO BE ABLE TO PROCEED WITH DIAGNOSE AND CHECKED FOR ANY OTHER SHORTED COMPONENTS". Vehicle is available for inspection. Vehicle was being driven on a city street towards a red light when the vehicle experienced a jolt and lost complete acceleration power and a "Check Hybrid System" was displayed on the dashboard. Luckily all vehicles behind were already coming to a stop for the red light, otherwise, the safety of my family and myself may have been put in more serious harm. Vehicle able to crawl to a nearby gas station. Attempted to use remaining battery power to drive back to residence nearby, but lost all battery power/function and puled into a bus lane where vehicle was towed from. There were no warning lights or messages displayed prior to the incident. Toyota Dealership performed DTC verification 3 times and found to verify P0A94 detail code 172 is the persistent DTC when memory is cleared. They also inspected the vehicle for concern and were able to verify Check Engine Light is ON, vehicle is on "Limp Mode" and does not "Ready ON". The vehicle has not been inspected by anyone else other than the Toyota Dealership.

• Oct 23, 2022TX
  Service brakes

  The break master cylinder is lighted up on the dashboard and the ABS system is not working which makes me sliding when I'm trying to use brakes. Too much noise coming when starting the engine for like a minute then it cool down The front chairs are not good for diver and passenger nick as it is one piece chairs with build in head stand and now I'm reviewing chiropractor for my nick frequently since I used this car

• Jun 30, 2022TX66,000 mi
  Electrical system · Hybrid propulsion system
  The contact owns a 2013 Toyota Prius C. The contact stated that while driving at slow speeds, the vehicle stalled as a system failure warning message appeared on the instrument panel. The vehicle inadvertently turned. The vehicle was restarted but shifted into limp mode with the message displayed.…

  The contact owns a 2013 Toyota Prius C. The contact stated that while driving at slow speeds, the vehicle stalled as a system failure warning message appeared on the instrument panel. The vehicle inadvertently turned. The vehicle was restarted but shifted into limp mode with the message displayed. The contact was able to restart the vehicle and then drove the vehicle to the residence. Upon investigation, the contact discovered NHTSA Campaign Number: 20V369000 (Hybrid Propulsion System) and 14V053000 (Hybrid Propulsion System, Electrical System) which she linked to the failure. Neither the dealer nor the manufacturer was notified of the failure. The vehicle was not repaired. The failure mileage was approximately 66,000.

• May 2, 2022TX
  Service brakes
  I bought my car as used, 3 months after that i hear a weird noise when i use the break, then I replace the break pads but it doesn’t solve the problem after that I got alert C1391, I went to mechanic shop he told me it needs to replace the break booster pump part number 4707052020, I did that but…

  I bought my car as used, 3 months after that i hear a weird noise when i use the break, then I replace the break pads but it doesn’t solve the problem after that I got alert C1391, I went to mechanic shop he told me it needs to replace the break booster pump part number 4707052020, I did that but doesn’t solve the problem and still the alert come and go. I want to know if this is general safety issue for this model and should be fixed by the dealer or i should fix it on my own

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Pedestrian alert sounds

  DP22005Opened Jan 27, 2023Closed Aug 7, 2023Recall 22V063000
  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for…

  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11007455Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
• 11007445The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
• 11007444To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
• 11007443Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
• 11006161Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
• 11006151The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
• 11006150To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
• 11006149Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
• 11005153Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
• 11005149Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
• 11005122Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
• 11005064Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
• 11003649The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
• 11003647To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
• 11003644Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
• 11003594The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
• 11003592To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
• 11003589Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
• 10253223This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
• 10251070OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
• 10244115TSB: The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks
• 10244113TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
• 10238157TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
• 10230369DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
• 10230368DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
• 10230367DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
• 10227920DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
• 10227919DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
• 10227918DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
• 10227916DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
• 10227915TI: TECHNICAL INSTRUCTIONS Customer Support Program ZKG Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
• 10227914CSP: Customer Support Program ZKG ? Paint Repair Process
• 10227913DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
• 10227912DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
• 10227898TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
• 10224108TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
• 10220183TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
• 10220174TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
• 10214323TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
• 10213902TSB: This bulletin includes basic procedures for performing a rescue charge on Ni-MH high voltage (HV) batteries. This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing a rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger

Every Toyota Prius C model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.