2020 Van Hool TDX25

Recalls

1 recall names the 2020 Van Hool TDX25. Newest first.

• Fuel system, diesel › Fuel injection system › Fuel rail

  May 25, 2021NHTSA 21V385000681 vehicles

  Van Hool N.V. (Van Hool) is recalling certain 2018-2021 CX35, TDX25, 2018-2019 CX45, TX45, 2021 AG300, and 2018 TD925 vehicles. The sealing washer may not seat correctly in the pilot bore holes, allowing the high pressure fuel rail assembly to leak.

  Risk and remedy

  Risk

  A fuel leak in the presence of an ignition source increases the risk of a fire.

  Remedy

  Dealers will inspect the rail threads, and replace the rail as necessary, free of charge. Owner notification letters were mailed on July 30, 2021. Owners may contact Van Hool customer service at 1-877-427-7278 or 1-407-656-7977. Van Hool's number for this recall is P1489.

  Full recall details →

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010424This service bulletin provides you with information about the location of emergency side window decals so that the vehicle meets the National Highway Traffic Safety Administrations (NHTSA) Federal Motor Vehicle Safety Standards (FMVSS) in the U.S and the Canadian Motor Vehicle Safety Standards (CMVSS) in Canada about this subject.
• 10250324an Hool feels very strongly about quality and constantly focuses on product improvement. This is why we would like to ask you to provide us with the correct information as quickly as possible when filing a warranty request. A fully documented diagnostic is key in this process. The more precise and complete the supplied information is, the quicker we can finalize your request, with financial compensation when applicable. For this reason, follow the procedure below as closely as possible
• 10248730This service bulletin provides you with information about the location of emergency side window decals so that the vehicle meets the National Highway Traffic Safety Administrations (NHTSA) Federal Motor Vehicle Safety Standards (FMVSS) in the U.S and the Canadian Motor Vehicle Safety Standards (CMVSS) in Canada about this subject.
• 10245018Van Hool regularly receives questions regarding the bolts securing the wheel suspension arms of the front axle and tag axles to the chassis. The purpose of this service information bulletin is to inform and is partly a reminder of what already is mentioned in the maintenance manual.
• 10233467Service Information: In its production process, Bock, manufacturer of refrigerant compressors, has switched to a new type of motor protection switch for the electric motor of the refrigerant compressor. As the MP10 motor protection switch (VH11472802) is no longer made available as a spare part, as of now you will receive the new INT69G motor protection switch (VH11691810) when ordering. The MP10 and the INT69G are interchangeable, but fastening and electric connection are different.
• 10219652Product Improvement: ALL VEHICLES WITH LIGHT-ALLOY WHEELS - Introduction of wheel-end monitoring system (WEM). Van Hool has released a wheel-end monitoring system (WEM) which can be installed on all vehicles equipped with light-alloy wheels. The WEM is installed at the outboard side of the wheel and monitors vibrations produced by the wheel bearing. It warns in case of bearing raceway spalling by flashing a red LED on the unit. The WEM is delivered with a magnet which is used to change from "transport" to "standstill" mode.
• 10210015Service Information: Removal and installation of Shaw DEF tank sensor unit The purpose of this service information bulletin is to inform you about the removal and installation of a Shaw DEF tank sensor unit.
• 10209998Product Improvement: Introduction of new generation DEF tank sensor unit Some previous manufactured DEF tank sensor units are no longer available as spare part. This service bulletin gives you information about the visual points of difference between the generations and which one to order in case of replacement. Most of the replacements are direct fit, except for the sensor units with an asterisk in the table which must be secured with a split mounting ring consisting of two halves instead of the original closed mounting ring.
• 10209996Field Change Program: Check refrigerant compressor wiring A rubber protection will be added at the top of the plate that holds the connectors. Missing plug seals will be added to the back of the 4-pin connector and the missing connector socket to the open connector on the compressor as well. Check for corrosion, bad pins should be replaced.
• 10209994Service Information - Introduction of new 4/2 solenoid valve in compressed-air circuit Van Hool has switched over into production to a new type of 4/2 solenoid valve in the compressed-air system. As the previous Knorr-Bremse (Bosch) solenoid valve (VH11102170) is no longer made available as spare part, customers will receive a Wabco solenoid valve (VH660526759) when ordering. Both valves are interchangeable, but some differences must be considered. Consult the information in this service bulletin for a proper installation.
• 10209992Service Information - Maintenance operations related to refrigerant compressor oil This service information bulletin is a reminder/update about refrigerant compressor oil maintenance. To ensure a reliable system, it is important to perform the maintenance on a regular base as mentioned further on.
• 10206914Introducion to electronic contrlolled air suspension(ELC).
• 10201570SERVICE INFORMATION BULLETIN: Van Hool has switched over into production to a new type of 4/2 solenoid valve in the compressed-air system. As the previous Knorr-Bremse (Bosch) solenoid valve (VH11102170) is no longer made available as spare part, you will receive a Wabco solenoid valve (VH660526759) when ordering. Both valves are interchangeable, but some differences must be considered. Consult the information in this service bulletin for a proper installation.
• 10190134Service Information Bulletin: What to do in case of prolonged vehicle standstill. This service bulletin provides an overview of works to be performed during prolonged vehicle standstill.
• 10182688Work Procedure: To reinforce structure of trailing axle module (fix on fail) This procedure has been released to assist in successfully reinforce the connection between the diagonals and horizontal tube in the trailing axle module.
• 10182687Service information Bulletin: Stress-free installation of flex pipe This service bulletin gives step-by-step instructions on how to install the flex pipe properly. The flexible part of the flex pipe handles thermal expansion and engine vibration, and is prone to premature breakdown in case of incorrect installation.
• 10180789Van Hool has optimized the multiplex program regarding to the foot brake functionally of the retarder. Owners and operators are requested to load the new multiplex program according to the step-by-step instructions given in this service bulletin.
• 10179511Van Hool N.V. and ABC Companies did not release any new service bulletins during the month of August 2020.
• 10176935Service Information Bulletin: The purpose of this bulletin is to inform you about how to align the cooling fan drive. This should be performed every time components of the fan drive have been removed, and when evidence of contact damage has been noticed on fan or shroud.
• 10174976Field Change Program: It has come to the attention of Van Hool that the fire suppression system, when activated while driving, shuts down the engine after 15 seconds. As a result of this, the door brake is automatically applied. To prevent this from happening while driving, it is necessary to load the newest version of the multiplex program. The newest version of multiplex program 11468111 is available through the Van Hool customer portal under the "Software" section.

Every Van Hool TDX25 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.