2006 Chrysler Sebring
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Chrysler › Sebring › 2006
These records cover every 2006 Chrysler Sebring. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
2 recalls name the 2006 Chrysler Sebring. Newest first.
Qualis automotive IS recalling certain aftermarket ball joints sold for use on certain passenger vehicles. the socket may have been excessively hardened which could cause it to crack near the retaining ring groove allowing the ball stud to separate under impact load. the subject ball joints were sold as four part numbers, d10945, d10946, g10945, and…
Risk and remedy
Risk
Separation of the ball stud from the socket of the ball joint housing would allow the control arm to collapse and the wheel to fold in causing loss of steering control, possibly resulting in a crash.
Remedy
Qualis automotive will replace the ball joints free of charge. the safety recall began on november 9, 2009. owners may contact qualis automotive at 1-800-493-4128.
Certain cardone master cylinders with part numbers 10-2925, 10-2987, 10-2987mza, 10-3083, 11-3015, 11-3042, 11-3044, 11-3045, 11-3047, 11-3064, and 11-3156, and with date codes lower than dca7078 sold as replacement equipment for use on the vehicles listed above. the seal on master cylinder can fail and leak brake fluid.
Risk and remedy
Risk
Loss of brake fluid can result in poor braking performance, possibly resulting in a vehicle crash.
Remedy
Cardone will notify owners and offer to repurchase any defective master cylinders. the recall began during april 2007. owners can contact cardone at 1-800-777-4780.
Owner complaints
120 complaints10 involved a crash11 injuries
What owners report most
Latest complaints
- Air bags
My passenger airbag spontaneously deployed without an impact when it was parked. This shattered the windshield and expelled plastic dashboard pieces and glass everywhere. My daughter and I had just exited the car so there were no injuries. Had we not stopped this may have deployed on the road or if…
My passenger airbag spontaneously deployed without an impact when it was parked. This shattered the windshield and expelled plastic dashboard pieces and glass everywhere. My daughter and I had just exited the car so there were no injuries. Had we not stopped this may have deployed on the road or if my passenger had waited in the car caused serious injuries. I contacted Chrystler to report this safety issue and they said this is no longer their responsibility due to my cars age and environmental factors. This happened 7/9/25 and the damages and airbag system is available to inspect. I have witnesses to seeing the deployment without impact and awaiting video footage from the business. No warning lights on the dashboard occurred. This is a very well maintained vehicle with very low miles.
- Seat belts
This is part of complaint 11630942. The incident on Nov 25, 2024. These are two separate complaints which occurred in the same crash that resulted in serious injuries. In the event of the crash the seatbelt failed to restrain me. Allowing my head to collide into the windshield and my chest to…
This is part of complaint 11630942. The incident on Nov 25, 2024. These are two separate complaints which occurred in the same crash that resulted in serious injuries. In the event of the crash the seatbelt failed to restrain me. Allowing my head to collide into the windshield and my chest to forcefully hit the steering wheel. I have serious injuries to many body parts as result of this incident. The vehicle is available for inspection and I have photos and medical reports available upon request.
- Air bags
At the time of collision the airbags did not deploy correctly. The airbag seems to have burst at the seams and projectlies of debris and chemicals came from the air bag instead. I hit my head on the windshield and hit my chest on steering wheel. I was burned on my arms, hands and ribs/chest. I…
At the time of collision the airbags did not deploy correctly. The airbag seems to have burst at the seams and projectlies of debris and chemicals came from the air bag instead. I hit my head on the windshield and hit my chest on steering wheel. I was burned on my arms, hands and ribs/chest. I have pulmonary and neurological injury. as well as changes to my sight and hearing. My car filled with thick "smoke" that was hot and made us choke and gasp for air. We breathed in these chemicals. My two disabled children were also injured by the chemicals.
- Air bags
The contact owned a 2006 Chrysler Sebring. The contact stated while driving at an undisclosed speed, the contact vehicle was involved in a crash. The contact rear-ended the vehicle that was in front of the contact vehicle. The contact's vehicle was damaged to the front driver's side of the…
The contact owned a 2006 Chrysler Sebring. The contact stated while driving at an undisclosed speed, the contact vehicle was involved in a crash. The contact rear-ended the vehicle that was in front of the contact vehicle. The contact's vehicle was damaged to the front driver's side of the vehicle. In addition, the air bags were deployed. The contact stated that the vehicle had a burning odor and lots of smoke. The Police and paramedics were at the crash scene. A Police report was filed. The vehicle was towed to a local tow yard. The vehicle was condemned to total loss by the insurance company. The contact's two minor children were occupants in the vehicle at the time of the crash. The contact was transported to the local hospital. The contact sustained burns to both left and right forearms, her right thumb, nerve damage to her left forearm, and bruised ribs. In addition, the chemical from the air bags entered the contact's nose and the contact had a continuous cough. The manufacturer was not made aware of the failure. The failure mileage was approximately 96,000.
- Steering
Mt ball joint separated from control arm housing
- Service brakes · Structure · Vehicle speed control › Accelerator pedal
The contact owns a 2006 Chrysler Sebring. The contact stated the accelerator pedal and the brake pedal were significantly close to each other causing him to depress both pedals at the same time. The contact stated while driving at 3 MPH and attempting to make a stop, his foot inadvertently…
The contact owns a 2006 Chrysler Sebring. The contact stated the accelerator pedal and the brake pedal were significantly close to each other causing him to depress both pedals at the same time. The contact stated while driving at 3 MPH and attempting to make a stop, his foot inadvertently depressed both the accelerator pedal and the brake pedal, causing the vehicle to crash into another vehicle. The air bags failed to deploy. There were no injuries sustained. A police report was filed. The contact stated the failure reoccurred while he was at a drive-through. He attempted to depress the brake pedal but depressed both the accelerator pedal and the brake pedal at the same time, causing the vehicle to lightly crashed into another vehicle. The air bags did not deploy. There were no injuries sustained. A police report was not filed. The dealer and the manufacturer were not notified of the failure. The vehicle was not diagnosed nor repaired. The approximate failure mileage was 145,000.
- Suspension
Front ball joint came off and caused car to come to crash into road. It is now in a repair shop where I had it towed as it was causing problems sitting on road. If I had been going faster I m not sure how serious a problem to me or others on road it would cause. Possible death. It is being…
Front ball joint came off and caused car to come to crash into road. It is now in a repair shop where I had it towed as it was causing problems sitting on road. If I had been going faster I m not sure how serious a problem to me or others on road it would cause. Possible death. It is being inspected by Advanced Automotive, 503-364-2046. The car has less than 50,000 miles on it and I don't understand how a front end (ball Joint) can go wrong that quickly. The only warning I had was a squeaking in the front end. Is this something normal? The mechanic said that there was a RECALL on this problem. Since I bought it used from a Chrysler dealer you would think they would clue me to the problems. HA HA.
- Engine · Seat belts
Drivers side seat belt Does Not Retract. Engine Piston Rod Bearings are defective heat up melt and may cause an Engine Fire like in Hyundai Rod Bearing Recall. Common on Chrysler V6 Engine. May cause Blown engine, snapped Piston Rods, Heat and Engine Fire.
- Unknown or other · Visibility/wiper
Turn signals, wipers and radio stopped working but intermittently.
- Seat belts
Front driver seat belt does not retract. Very dangerous. *tr
- Engine
My engine overheated due to a water pump leak. The temperature gauge remained in the normal operating range during my trip which was about 30 miles of mostly highway driving. I had no indication that anything was wrong with my car until it shut off at a stop light.
- Air bags · Exterior lighting · Structure › Body
We were in a car accident and although we were hit in the front, the air bags did not deploy.
- Suspension
While driving I was hearing noise under car. Then front drivers wheel came off damaging car above the tire while I was driving on the street at about 35 miles. Car was towed in to firestone where they had to replace ball joint and arm. Among the maintenance after that I was then told on passengers side the lower control arm ball joint was about to fall off.
- Unknown or other
Horn going off while driving or parked.
- Wheels
TL* the contact owns a 2006 chrysler sebring. While driving 10 mph, the front passenger wheel detached from the vehicle without warning. The body of the vehicle fell to the ground and sustained damages. The vehicle was towed to an independent mechanic who was unable to determine the cause of the failure. The manufacturer was not notified of the failure. The failure mileage was approximately 94,000.
- Service brakes · Vehicle speed control › Cruise control
TL* the contact owns a 2006 chrysler sebring. While driving, the cruise control inadvertently fluctuated. In addition, there was a grinding noise when the brake pedal was depressed. The vehicle was taken to the dealer, but was not diagnosed or repaired. The manufacturer was not made aware of the failure. The vin was unknown. The failure mileage was 80,000. ...updated 03/13/17 *bf *cn
- Engine
Engine light stay on all the time always serviced and changed oils on time or before, replaced all sensors, plugs, engine does shake on idle and shut itself off even while driving and/or in moving motion, engine light always on.
- Electrical system
Horn goes off on its own while driving. Same sometimes when it's parked unattended. this recurs once a week or so.
- Unknown or other
Horn goes off all by it's self when car IS off any time of day or night only way I could get it to stop was to pull horn fuse witch may disable airbag .possible cause IS a clock spring in witch dealer claims to have never heard of before but when typed on line about it the problem it finishes your sentence. Sounds pretty common to me.this problem could cause the airbag to fail and cause injury to the driver or death
- Electrical system › Horn
TL* the contact owns a 2006 chrysler sebring. Without warning, the horn continued to sound and the noise continued randomly for weeks. The vehicle was inspected by an independent mechanic and taken to a dealer for inspection and diagnostic testing. The manufacturer was notified of the failure. The approximate failure mileage was 61,000.
- Unknown or other
The horn goes off without warning. the first time IS happened was a couple of months ago while driving down a city street at 6:10am (taking my child to school). the horn went off a various times (while driving down major city streets) for a few days. on saturday 1/2/16 I started (in my driveway)…
The horn goes off without warning. the first time IS happened was a couple of months ago while driving down a city street at 6:10am (taking my child to school). the horn went off a various times (while driving down major city streets) for a few days. on saturday 1/2/16 I started (in my driveway) the car and the horn went off. I pushed the steering wheel the horn stayed on, next I pushed the panic button, it stayed on until I pushed the panic button a second time about 2 minutes later. then on the same day while driving on a (main city street) the horn went off four times within five minutes. however, each time it the horn turned off when I pushed the steering wheel. This morning 1/4/16 the horn went off several times back to back for about a minute, only turning off when I pushed the steering wheel. Did a google search and found 57 complaints (complaint.com) about the same horn problem. Suggested I add my voice to what IS clearly a problem.
- Unknown or other
My horn goes off for no apparent reason. while driving down the road it goes off and to get it to stop I had to hold my hand lightly over the air bag and horn buttons on the steering wheel.
- Unknown or other
I am writing to the national highway traffic safety administration to file a complaint against the fiat-chrysler company. Since the beginning of february 2015, my horn has been going off when my IS parked at night time, and therefore many complaints have been reported by my neighbors, when my horn…
I am writing to the national highway traffic safety administration to file a complaint against the fiat-chrysler company. Since the beginning of february 2015, my horn has been going off when my IS parked at night time, and therefore many complaints have been reported by my neighbors, when my horn automatically goes on during the hours of the night, it IS very upsetting having to explain my situation to the neighbors. a technician at one of the fiat-chrysler repair centers diagnosed the problem and stated that the problem was the due to a bad switch that controls the driver's side airbag and horn, and that would cost over $1,000 to repair. The dealership stated that I would have to repair it because it wasn't recall issue. Because of the fact that I am on permanent disability and on a very low income, I am unable to afford to repair it. after realizing that there IS no light in sight, I began to research as to how many other consumers/or chrysler sebring owners are experiencing the same problem as I am presently experiencing. I have discovered that there were approximately 52 complaints from sebring car owners listed in the following site: http://www.carcomplaints.com/chrysler/sebring/2006/accessories-interior/horn_goes_off_by_itself. Shtml thus I must request that the nhtsa's launch an investigation against the fiat-chrysler company by setting forth a recall to this subject matter. I am requesting a prompt reply for an immediate resolution to my situation, hoping the nhtsa can take this matter seriously before fatalities do occur on my behalf. please contact me on my email at [xxx]@gmail.com of by phone [xxx]. [xxx] information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(B)(6).' *jb
- Suspension
Ball joint cracked badly which IS causing the ball stud to wear through the control arm housing resulting in noise and/or separation of the ball stud from the housing.
- Engine and engine cooling
2006 chrysler sebring. consumer writes in regards to oil leak in vehicle engine area. *smd the consumer stated the water pump and timing belt were replaced on january 27, 2015 after which, an oil leak developed. After two crankshaft oil seal replacements the consumer was informed the problem…
2006 chrysler sebring. consumer writes in regards to oil leak in vehicle engine area. *smd the consumer stated the water pump and timing belt were replaced on january 27, 2015 after which, an oil leak developed. After two crankshaft oil seal replacements the consumer was informed the problem appeared serious enough to contact chrysler about a further diagnosis. The consumer was able to identify a problem which resulted in a technical service bulletin identifying the problem as crankshaft end play resulting in oil seal performance and leakage. The recommended action was to install a second thrust bearing to eliminate crankshaft vibration/movement. *jb updated 09/21/15*lj updated 12/06/2017*cn
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10229256KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.
- 10229181Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10229178Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10223602Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223599Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10221686KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.
- 10221515Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10221512Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
- 10220489Valve Body. These may cause over drive cycling.
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 1021645482212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
- 10191460Valve Body. These may cause over drive cycling.
- 10175743Disinfectant Solution Recommended for COVID-19
- 10175735Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
- 10169249Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10169247Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10169245Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10130081Return: Wiring Assy - Engine You have been identified as either having stock, or have stock in transit to your dealership. Please return stock packaged before 2016/07/31 (31 July, 2016)of follow ing part numbers:68176457AF, 68176459AF. Please return suspect parts back to your facing depot using Return Code 02, before 13 September, 2016.
- 1013008005182535AD - Lamp Assy ?Tail Light LT You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05182535AD . See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
- 10130079Inspect and Return: Trim Cover Assy - A-Pillar Rt/Lt You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part numbers: 1ZA04DX9AE, 1ZA05DX9AE. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
- 10129047Warranty Operations Newsletter Updates from Warranty Operations
- 10129046Warranty Operations Newsletter Updates from Warranty Operations
- 10129045CBXDP361AA Return: Spacer Kit - Visor You have been identified as either having stock, or have stock in transit to your dealership. Please return stock of part number CBXDP361AA. Replacement part number is CBXDP361AB w hich is in stock and available for order. Please return suspect parts back to your facing depot using Return Code 02, before 16 September, 2016.
- 101290441NT30XDVAC - Inspect and Return: Panel - Instrument Panel You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 1N T30XDVAC. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
- 10129043Inspect and Return: Solenoid Module - Transmission You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of follow ing part numbers:52120000AA, 52119435AF, 05078709AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
- 10129042Return: Lamp Assy - CHMSL& Cargo Light You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of follow ing part numbers:55372082AE, 55372082AD, 55372082AC, 55372082AB, 55372082AA. Replacement part number is 55372082AF w hich is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
- 10129041P/N CBSZR068AA: Inspect & Return: Module Kit - Occupant Restraint You have been identified as either having stock, or have stock in transit to your dealership. Please return part number CBSZR068AA as per the QIR attached. Replacement part can be obtained by ordering the same part number (CBSZR068AA) Please return suspect parts back to your facing depot using Return Code 02, before 02 September, 2016.
- 1012900882212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
- 10121927NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
- 10121832Wiper If Mopar OE wipers are unavailable, the below alternatives can be offered instead. 05066964A$ = WBRW0011A$ 05066973A$ = WB000019A$ or WBF00019A$ 05096134A$ = WB000027A$ or WBF00028A$ 55154762A$ = WB000013A$ 68001330A$ = WB000019A$ or WBF00019A$ 05012611A$ = WB000021A$ or WBF00021A$ 05102881A$ = WBRW0011A$
- 10023351Exterior lamp - lens fogging.
- 10021248Cracked windshield due to being hit by a foreign object like a stone.
- 10021239Powertrain control module initialization.
- 10019743Rough idle, malfunction indicator lamp illumination, diagnostic trouble code p0303.
- 10019538Valve seat not properly seated in the cylinder head.
- 10017651Revised power steering system bleeding procedures.
- 10016603Air conditioning (a/c) cooling coil odor.
Every Chrysler Sebring model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.