2008 Dodge Caliber

Owner complaints

What owners report most

1. Suspension113
2. Structure88
3. Electrical system59
4. Engine43
5. Power train38
6. Steering35
7. Unknown or other28
8. Vehicle speed control27
9. Air bags23
10. Wheels16

Latest complaints

• Aug 2, 2023OH
  Engine · Steering · Wheels

  My vehicle has created a rotten subframe that holds my engine

• Jan 18, 2023CA120,000 mi
  Engine · Steering
  The contact owns a 2008 Dodge Caliber. The contact stated that while driving at various speeds in the rain, the vehicle stalled. The contact stated that the power steering became inoperable. The battery warning light was illuminated. The vehicle was taken to the local dealer where it was diagnosed…

  The contact owns a 2008 Dodge Caliber. The contact stated that while driving at various speeds in the rain, the vehicle stalled. The contact stated that the power steering became inoperable. The battery warning light was illuminated. The vehicle was taken to the local dealer where it was diagnosed and determined that an unstated computer needed to be replaced. The vehicle was not repaired. The manufacturer was contacted but no additional assistance was provided. The approximate failure mileage was 120,000. The contact stated that the vehicle is unsafe to drive and the mechanics has not found a resolution to the problem yet.

• Jan 16, 2023CA
  Unknown or other

  My car shuts down while driving These cars recalled July10 2008 Mine was made April18 2008 but has the same issue It could cost lives

• Dec 11, 2022PA
  Suspension
  Rear subframe rusted right through control rods snapped rear end of car dropped down. Upon researching they know that this is bad and unsafe even gave a 10 year extended warranty for front and rear subframe so how long will and how many complaints before this is an actual recall. I see here in your…

  Rear subframe rusted right through control rods snapped rear end of car dropped down. Upon researching they know that this is bad and unsafe even gave a 10 year extended warranty for front and rear subframe so how long will and how many complaints before this is an actual recall. I see here in your complaints that there is a large number of complaints on this issue. How are they getting away with this and nothing being done. I will have photos also police had said if this happened while it was on interstate would have crashed and could have been fatal. The tire would have ripped right off. So not only was my safety but the safety of the others being jeopardized cause everyone just keeps looking away at this issue. I would love to know how many of these subframes have had to be replaced I bet if you do research there is not one of them out there that either should be replaced have been replaced or will need to be replaced. Stop allowing these car companies to use sub standard parts. I am sure this will fall to the wayside along with the other 100 complaints. I will try my hardest to make sure everyone knows this is a problem that the car company is fully aware of and nobody has done anything about and keep researching on how many more this has happened to and try to get everyone to file a complaint. There was NO WARNING SIGN just broke loose passenger side of car was practically on the ground the broken control arm is what held everything up. Please can we really check into this if there is a recall at least people will know the problem exist.

• Dec 8, 2022OH
  Engine · Suspension · Vehicle speed control
  I’ve only had the car since Aug. Im the second owner, it drove just fine. Then I got an oil change. Then the car began to rev down hill and struggled to make it uphill. Then my exhaust became excessively loud. Then the wheel became loose ,and started pulling ALOT. I was on my way to get an…

  I’ve only had the car since Aug. Im the second owner, it drove just fine. Then I got an oil change. Then the car began to rev down hill and struggled to make it uphill. Then my exhaust became excessively loud. Then the wheel became loose ,and started pulling ALOT. I was on my way to get an alignment this morning and the whole front end began to buckle not even a minute down the road. I tmade it in back the driveway before the front end collapsed completely

• Nov 24, 2022NC
  Electrical system · Structure › Body · Suspension
  The entire underneath of my car is rusted out. I was driving to work one day when someone pulled out in front of me and I had to hit the brakes. That resulted in the subframe and front drivers axel to break as I’m driving! The sunroof leaks when it rains and half the time the electricity doesn’t…

  The entire underneath of my car is rusted out. I was driving to work one day when someone pulled out in front of me and I had to hit the brakes. That resulted in the subframe and front drivers axel to break as I’m driving! The sunroof leaks when it rains and half the time the electricity doesn’t work on the sunroof button. My doors have completely stopped auto locking and my hazards will randomly start flashing without pushing the button. Steering is absolutely terrible, it feels like you’re skidding on ice or hydroplaning the entire drive.

• Nov 12, 2022IA
  Suspension

  Rear crossmember/ subframe rusted thru and broke. Replaced front several years ago. Car has always been garaged.

• Jul 7, 2022MN
  Unknown or other

  2008 Dodge Caliber with approx. 135,000 miles on it. Rotted subframe and rusted crossbar. Vehicle started swerving as if driving on ice (in the summertime!). Took it to a reputable mechanic and he wouldn't even put it on a lift. He said it was too much of a risk. I understand this is common on this vehicle, it's dangerous and should be recalled! NO more Dodge vehicles for me, ever!

• Apr 15, 2022NJ
  Structure › Body · Unknown or other

  Subframe rusted front and rear Was driving tire axel/rod broke entire underneath rusted rotted

• Jan 12, 2022MO
  Steering · Suspension · Unknown or other
  I was informed at inspection that the main front cross member has a huge hole in the center of it and is rusting out badly. At 162,356 miles this car will not pass safety inspection. This car is not safe for me or my family. No warning lamps or messages. I was told that one bad bump could do us in.…

  I was informed at inspection that the main front cross member has a huge hole in the center of it and is rusting out badly. At 162,356 miles this car will not pass safety inspection. This car is not safe for me or my family. No warning lamps or messages. I was told that one bad bump could do us in. We were told to contact the dealership and found out about the extended warranty that had already passed during the previous owners time. This should have been a recall, but what else can you expect from dodge.

• Sep 23, 2021NH159,000 mi
  Structure › Frame and members › Underbody shields

  The contact owns a 2008 Dodge Caliber. The contact stated while taking the vehicle into a local state inspection, he was notified that the vehicle did not pass inspection due to the K-frame of the undercarriage was fractured due to corrosion and rust. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 159,000.

• Apr 7, 2021NJ99,999 mi
  Structure › Body · Suspension
  2008 dodge caliber sub frame/k-frame front end crossmember completely rusted thru causing the driver side lower control arm to rip free from frame (seperating part of frame, with lower control arm) from rest of frame. This left driver with no control of affected wheel which turning it 90 degrees…

  2008 dodge caliber sub frame/k-frame front end crossmember completely rusted thru causing the driver side lower control arm to rip free from frame (seperating part of frame, with lower control arm) from rest of frame. This left driver with no control of affected wheel which turning it 90 degrees out from normal operating position. Left operator with no ability to steer while driving on main primary (35 mph speed limit) two lane road. Car slid to halt in middle of road. Car needed to be towed. Dodge/chrysler apparently knew of this problem and never notified owner. Please see attached notice. front and rear crossmember corrosion (X69 warranty extension) - 2008-2012 dodge caliber & jeep compass/patriot oemdtc july 17, 2017 15 comments nhtsa ID number: 10140027 manufacturer communication number: 23-007-17 rev. B summary front and rear crossmember corrosion (X69 warranty extension) the driver of this car could have been killed or seriously hurt. It IS unfathomable that dodge chrysler was allowed to get away with not notifying potential crash victims

• Jan 2, 2021AL283,000 mi
  Electrical system · Service brakes · Wheels
  The front calipers will not engage when brake pedal IS pressed. The brake pedal sinks to the floor and has no stopping power. The master cylinder was replaced and calipers are new replacements. After replacing these parts it now smell of burnt brake fluid but there IS no leak and the problem seems…

  The front calipers will not engage when brake pedal IS pressed. The brake pedal sinks to the floor and has no stopping power. The master cylinder was replaced and calipers are new replacements. After replacing these parts it now smell of burnt brake fluid but there IS no leak and the problem seems to worsen. The first time I was doing 45-50 on a county rd when a another car pulled out 20 feet away and I was trying to slow down when I lost the front brakes as pished in on the pushed in on the brakes the pedal sank and they didn't engage. I then bought the new calipers and it was fine for about a month. The second time I was stuck in traffic on a busy city street when the ABS brakes failed resulting in me running a red light and almost getting hit. It has corroded and took hunks off aluminum from my front driver rim. I have not been able to figure out what the problem and keep replacing parts for it to tear up new ones

• Jan 1, 2021DE
  Unknown or other
  Took vehicle in for maintenance, technician told us the front crossmember IS rusted throughout and needs replacement. technician advised it's a safety issue and this model was given extended warranty under X69 notice, however warranty may have already expired. I contacted chrysler representative…

  Took vehicle in for maintenance, technician told us the front crossmember IS rusted throughout and needs replacement. technician advised it's a safety issue and this model was given extended warranty under X69 notice, however warranty may have already expired. I contacted chrysler representative and they advised the vehicle was part of the X69 notice but was beyond the extended warranty that expired in june 2018. I am the second owner of vehicle band never received notice of the issue from chrysler/dodge. the crossmember rust issue appears to be a common problem with this model. I am requesting an investigation and recall for this part.

• Sep 20, 2020FL100,000 mi
  Power train

  After reaching 100K miles, I took the car to the dealership to have the transmission flushed. Since then my transmission over heats when I drive 65 or more mph. I brought it back to the same dealer about a year later and they wanted to charge me $1500. I walked out! I drive 64 mph to keep it from over heating.

• Sep 20, 2020FL
  Suspension

  I have had my 2008 dodge caliber since 2009. Since then I have replaced both tie rods 4 times. I just had them done again about 1 1/2 years ago and they are broken again. I have changed the ball joints as well.. This IS ridiculous and should have been recalled I read a lot of forums and everybody complains about the same thing.

• Jul 18, 2020WI133,687 mi
  Suspension

  My 2008 dodge caliber cross-member broken in the midst of me driving

• Jun 30, 2020OH190,000 mi
  Structure › Body · Suspension
  Recently purchased a 2008 dodge caliber(ohio). On initial drive returning with vehicle I noticed a vibration coming through steering wheel. Upon inspection, was informed the tie rod ends and control arms both could use replacement, but could have been caused by the more important bad front and rear…

  Recently purchased a 2008 dodge caliber(ohio). On initial drive returning with vehicle I noticed a vibration coming through steering wheel. Upon inspection, was informed the tie rod ends and control arms both could use replacement, but could have been caused by the more important bad front and rear crossmembers as well as front and rear crash bars, both have severe rust development with metal deterioration which could impose a safety concern down the road. Was advise to look into replacement. Reached out to one of the local dealerships and was informed it was a bulletin, had an extended warranty, but am outside of 10 year period. Rust from crossmember IS now in process of transferring to actual frame and coming through as holes in rockers now as well. Dealership offering no help after stating the enhanced safety concern. Hard to believe an 08 can deteriorate so fast. You would think with the complaints and t.s.b. As well as safety concerns, seeing still original parts that have been warrantied to replace but have not on this vin, gets no help at all. *tr

• Jun 26, 2020OH48,000 mi
  Steering · Suspension

  Making noise going around bend 06052020. *tr

• May 31, 2020MN240,000 mi
  Electrical system · Electronic stability control (esc) · Power train

  While driving my car speed lowered and the trans temp light and esp light and traction control and etb module light came car won't go over 40 and remains in limp mode even after taking it to the shop

• May 26, 2020OH104,392 mi
  Structure › Body · Suspension · Unknown or other
  While my wife was driving, the front subframe crossmember rusted through, causing her to lose control of the car and she could not safely operate it without repair. I managed to get it to a firestone for them to look at and they referred me to a dealer and told me not to drive it anymore because it…

  While my wife was driving, the front subframe crossmember rusted through, causing her to lose control of the car and she could not safely operate it without repair. I managed to get it to a firestone for them to look at and they referred me to a dealer and told me not to drive it anymore because it IS unsafe. This IS a problem that dodge knew about, but failed to notify me about. I only found out about the problem from the dealership, who told me that the extended warranty that covers this problem had expired in 2018 and that I would be responsible for the cost of any repairs. I owned the car during that time and I did not know of this problem, so I could not act on getting it repaired. This never should have been an extended warranty, this should have been a recall because of the potential to kill people when the subframe rusts out. My wife was driving in a parking lot at the time at a relatively low speed, but had this happened on a highway it could have killed her and my son, as well as others on the road. number: 23-007-17 rev. B group: body date: march 10, 2017 *tr

• May 11, 2020MO90,000 mi
  Electrical system · Engine
  Luckily, I was on a city street. The vehicle lost power and slowed significantly, almost stopping completely and began to reboot as if it were just being started. I am complaining because I do not feel it to be safe for consumers on any road. I have a 3 year old son and I would very much like dodge…

  Luckily, I was on a city street. The vehicle lost power and slowed significantly, almost stopping completely and began to reboot as if it were just being started. I am complaining because I do not feel it to be safe for consumers on any road. I have a 3 year old son and I would very much like dodge to fix this problem before my, or anyone else's family, gets whiplash from a rear collision. I'm reaching out to nhtsa because, I lack the tools and knowledge to fix it myself, and don't find it fair that I pay for a mistake that dodge made in making the car. *tr

• Jan 13, 2020IL
  Suspension
  I previously called regarding odi 11282835. The front and rear cross-members were completely rusted away. There was an extended warranty and the original owner never repaired the issue the warranty expired 04/2018. Chrysler refuses to fix the issue. I purchased the vehicle 09/2019 and discovered…

  I previously called regarding odi 11282835. The front and rear cross-members were completely rusted away. There was an extended warranty and the original owner never repaired the issue the warranty expired 04/2018. Chrysler refuses to fix the issue. I purchased the vehicle 09/2019 and discovered the entire suspension had rotted out. This IS extremely dangerous. It IS pursuant to this bulletin. Chrysler IS refusing to repair it. service bulletin number: 23-012-14 group: body date: may 19, 2014 this bulletin IS supplied as technical information only and IS not an authorization for repair. note: this only applies to vehicles in the canadian market and in salt belt states which include connecticut, delaware, illinois, indiana, iowa, maine, maryland, massachusetts, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, washington, d.c., west virginia and wisconsin. subject: front and rear crossmember corrosion (X58 10 years unlimited mileage) overview: this bulletin involves inspecting the front and rear crossmembers for perforation / rust through and if necessary, replace the crossmember(s). models: 2007 pm caliber 2007 mk compass, patriot note: this bulletin applies to vehicles built on or after august 26, 2005 (mdh 0826xx) and on or before july 23, 2007 (mdh 0723xx). symptom/condition: the customer may describe a vibration at the steering wheel or may have been informed by a technician or state vehicle inspection that the front and / or rear cross-member IS severely corroded. policy: warranty period for cross-member perforation / rust through IS extended to 10 years. reimbursable within the provisions of the warranty.

• Jan 10, 2020PA97,000 mi
  Air bags

  My airbag light started giving me problems in september 2019, the airbag light comes on and off when stationary, and in motion.

• Dec 3, 2019NC124,000 mi
  Steering · Suspension · Wheels
  I was turning in my vehicle for a trade in and during the appraisal test drive the axel broke and it had to be towed. the gentlemen stated that IS was due to rust build up. over the years, I have complain about the power steering feeling off, the car not driving right, etc and it has been in…

  I was turning in my vehicle for a trade in and during the appraisal test drive the axel broke and it had to be towed. the gentlemen stated that IS was due to rust build up. over the years, I have complain about the power steering feeling off, the car not driving right, etc and it has been in three places where the maintenance folks said nothing was wrong. according to the bulletin, these same issues should have been caught somewhere to prevent this from happening. I may have been notified but I am active duty military and move every two years to include deployments where I easily could have not received the notice. My car value was 1500 dollars before it was wrecked, but I should be reimbursed for the previous maintenance totals and the lost days of not having my car the other times it should have been fixed. below, I will show pictures of the rust, inspections that was done in june 2018 showing that underneath was good, and previous work on my vehicle when I complaint of issues with steering, tires, suspension. Number: 23-007-17 rev. C group: 23 - body date: july 13, 2017

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
• 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
• 10229181Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
• 10223854Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].
• 10223602Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
• 10223599Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
• 10223512THROTTLE BODY For clarification, only use 68414676A$ on 2010 & earlier vehicles as supply is limited.
• 10223509TRANSMISSION, 5 Speed On replacing OE transmission 05106567A$/68042567A$ with reman transmission R8142074A$ replace with new Hydraulic Clutch Tube 05273429A$ to avoid interference with shift lever
• 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
• 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
• 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
• 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
• 10218307Flash: UConnect and Voice Recognition Inoperative This bulletin involves replacing the Hands Free Module (HFM). The customer may describe the following conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality
• 10217559Front And Rear Crossmember Corrosion (X69 Warranty Extension) This bulletin involves inspecting the front and rear crossmembers for perforation/rust through and if necessary, replacing the crossmember(s). Customers may describe a vibration at the steering wheel or may have been informed by a technician or state vehicle inspection that the front and/or rear crossmember is severely corroded.If the customer describes the symptom/condition listed above, perform the Diagnostic Procedure.
• 10216395Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
• 10191460Valve Body. These may cause over drive cycling.
• 10177457THROTTLE BODY For clarification, only use 68414676A$ on 2010 & earlier vehicles as supply is limited.
• 10177454TRANSMISSION, 5 Speed On replacing OE transmission 05106567A$/68042567A$ with reman transmission R8142074A$ replace with new Hydraulic Clutch Tube 05273429A$ to avoid interference with shift lever
• 10175743Disinfectant Solution Recommended for COVID-19
• 10175735Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
• 10169249Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
• 10169247Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
• 10169245Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
• 10166537RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
• 10140258Flash: UConnect and Voice Recognition Inoperative This bulletin involves replacing the Hands Free Module (HFM). The customer may describe the following conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality
• 10140065Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
• 10140027Front And Rear Crossmember Corrosion (X69 Warranty Extension) This bulletin involves inspecting the front and rear crossmembers for perforation/rust through and if necessary, replacing the crossmember(s). Customers may describe a vibration at the steering wheel or may have been informed by a technician or state vehicle inspection that the front and/or rear crossmember is severely corroded.If the customer describes the symptom/condition listed above, perform the Diagnostic Procedure.
• 10139985Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
• 10139978Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
• 10138987Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
• 1012900882212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
• 10128948Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
• 10121927NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
• 10076509SUBJECT: Flash: UConnect and Voice Recognition Inoperative SYMPTOM/CONDITION: The customer may describe the following conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality
• 10064501Summary to be provided on a future date.
• 10034545Dodge: fuel gauge fluctuation. Fuel gauge IS not accurate or fluctuates at 3/4 of a tank or above. This bulletin involves replacing the fuel sending unit, clocking the fuel module and installing a fuel jumper hose.
• 10032766Chrysler/jeep/dodge: california emissions warranty addendum. The warranty book on certain vehicles may contain errors or may be missing information regarding the coponents covered by the california emissions warranty. Dodge-caravan/grand caravan, charge/charger SRT8, magnum/magnum SRT8, viper, avenger, nitro, challenger/challenger SRT8, durango/durango hybrid, journey, RAM 2500/3500, caliber/caliber SRT4; jeep commander, grand cherokee/grand cherokeesrt8, compass, patroit, liberty; chrysler town&country, pacifica, 300 SRT8, ptcruiser, sebring/sebring conv., aspen/aspen hybrid.
• 10026829Chrysler: lower control arm to crossmember mounting bolts. Vehicles were shipped with front lower control arm to crossmember mounting bolts that may not be tightened to specification.
• 10026764Chrysler\dodge service campaign: see document search button for owner letter. Vehicles may have been inadvertently programmed with software that disabled three engine diagnostic monitors. Without monitors, an improperly operating component may go undetected and result in excessive exhaust emissions. Csc letter was received. 1/23/09.
• 10025384Flash: mil illumination with dtc p0139 or 02270. This bulletin involves selectively erasing and reprogramming the powertrain control module (pcm).

Every Dodge Caliber model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.