2009 Hino NJ8J
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2009 Hino NJ8J. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2009 Hino NJ8J. Newest first.
Hino Motors Sales U.S.A., Inc. (Hino) is recalling certain 2007-2019 NJ8J (258ALP) vehicles. These vehicles do not have dust shields on the front brake assemblies. During wet conditions, uneven water saturation on the front brake assemblies may result in the vehicle pulling to the left during hard braking.
Risk and remedy
Risk
If the vehicle pulls left, it may cross into another lane unexpectedly, increasing the risk of crash.
Remedy
Hino will notify owners, and dealers will install new brake drums with dust shields, free of charge. The recall began March 19, 2019. Owners may contact Hino customer service at 1-248-699-9390. Hino's number for this recall is AACL0.
Hino is recalling certain model year 2005 through 2013 medium duty trucks, models NA6J, NB6J, NC6J, ND8J, NE8J, NJ8J, NF8J, and NV8J, manufactured from August 18, 2003, through November 16, 2011. Over time, the main B+ circuit from the battery to the starter could potentially short to ground due to wear that accumulates as a result of interference between…
Risk and remedy
Risk
If the B+ circuit shorts to ground, it may lead to a fire.
Remedy
Hino will notify owners, and dealers will repair the vehicles free of charge. The recall began on January 17, 2013. Owners may contact Hino at 1-248-699-9390.
Hino IS recalling certain trucks with vertical exhaust pipes. certain bolts attaching the exhaust system to the truck may not have been properly tightened during the manufacturing process. The bolts could fail allowing the exhaust system to separate from the truck.
Risk and remedy
Risk
The exhaust system could fall onto the roadway and be struck by a following vehicle resulting in a crash.
Remedy
Hino will notify owners and dealers will repair the vehicles free of charge. the safety recall began on november 9, 2010. owners may contact hino at 248-699-9330.
Hino IS recalling 130 my 2008-2009 ND8J, NE8J, NJ8J, and NV8J conventional trucks. the rear axle u-bolts were not properly tightened. the lower spring seat may not contact the axle housing properly, producing a gap on the front or rear side of the axle housing.
Risk and remedy
Risk
This gap could allow the u-bolts to loosen and/or cause the lower spring seat to crack. the axle could become misaligned and/or separated from the mountings increasing the risk of a crash.
Remedy
Dealers will inspect the rear air suspension lower spring seat for a gap between the rear axle and lower spring seat. the u-bolts will be tightened to the specified torque. the recall began on january 19, 2009. owners may contact hino at 1-248-699-9330.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11000898This article will provide dealership technicians with information on how to open a tech assist case and discuss what is required when opening a Tech Assist Case.
- 11000897After connecting to a truck using DX3, it may be necessary to review or create a DX Diagnostic Report for review.
- 10185627When replacing an engine block with service part no., 11401E0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have these 2 oil passage plugs, you will need to install them before proceeding
- 10185598In the event that one of the subject vehicles is driven while the ABS warning lamp is illuminated, operation of the torque converter clutch will be suspended. Driving the vehicle with an ABS warning lamp illuminated can lead to overheating of the transmission fluid due to the torque converter clutch not functioning. A jumper harness has been made available that will allow operation of the torque converter clutch in the event that the vehicle is driven while the ABS warning lamp is illuminated.
- 10184199This bulletin provides diagnostic information for monitoring the engine running data to determine if the Suction Control Valve is defective, and a service procedure for replacing the Suction Control Valve when necessary. The SCV should be tested and replaced when necessary before replacing the supply pump assembly for a fuel pressure related concern.
- 10184170Hino Quick Reference Guide 2005-2010 Model Years
- 10182811This document is to inform dealers and workshops of the design change to the supply pump and SCV for J08E-TV, TW engine series.
- 10182810This document is to inform dealers and work shops to the update of inlet and outlet fuel pipes on the Davco fuel filter assembly.
- 10159329Sa-19-011 aacl0 conventional alp drum and dust shield procedure changes
- 10119458TT-16-013 The procedure for installing the rocker shaft bolts into the cam housing has been updated. It is recommended to lightly lubricate the threads and flange of the bolts with clean engine oil before installing them. The torque specification has also been reduced as a result of adding lubricant to the bolts.
- 10118109TT-15-016 The purpose of this publication is to communicate the standard measuring positions on the Hino chassis. In some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards the driver side or passenger side. The following publication can be referenced to obtain the manufacture?s measurement positions and specifications. Should the truck not meet the specifications, you should consider the following potential causes noted in the inspection guideline section below.
- 1011810507 - 006 voltage drop test
- 10118099SB-13-009 This bulletin is to inform dealers and workshops of proper paint codes for all Hino models. ALL MODELS
- 1011809413-008 Design Change of the Idler Gear Case and Idler Gear Bolt. Abnormal load such as a stuck supply pump was applied to gear train then causing the bolt to loosen. Therefore, an enhancement to the case and bolt were carried out. The idler gear case and bolt were changed to increase the robustness for the abnormal load. The details are as follows.
- 10118085Sb-11-002 requirements of biofuel usage for 2008my thru 2012my vehicles all applied models
- 10117752SB-16-021 CORRECTION OF WORKSHOP MANUAL FOR HINO600 SERIES Correction of Electrical Wiring Diagram
- 10117748SB-16-010 Correction of the inspection of the DPR filter.
- 10117728TT-14-029 A subject vehicle at 200,000 miles may exhibit a "DPR Maintenance" message displayed on the Instrument Cluster message center. The following procedure will instruct how to check the DPF and reset the displayed message.
- 10117723TT-14-021 This procedure illustrates a worst case scenario repair procedure, the process and materials being used are the same for all repairs. Depending on the location of the repair, access may be limited in some cases. Ensure that the repair area extends at least 2 inches on either side of the cracked area.
- 10117680SB-15-026 A subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. An improved head gasket has been made available as a service part and should be used if replacement of the head gasket is necessary. Improvement of the head gasket includes the addition of rubber seals around the engine oil and engine coolant port holes.
- 10117678SB-15-022 In the rare event that a subject vehicle equipped with the 23k Comfort Ride air suspension experiences a premature main leaf failure, a 23k HD Comfort Ride air suspension may be installed with PRIOR APPROVAL from HMM QA.
- 10117673SB-15-017 New parts are available to prevent repeat exhaust manifold stud failures on the J05 engine. This bulletin provides instructions for an exhaust manifold attachment modification at the #1 and #4 cylinder locations. Modifications to the manifold insulator shield and the turbocharger water return pipe have also been made to accommodate the longer studs.
- 10117671SB-15-015 Information of Troubleshooting Procedure for Engine Lacked Power during the DPR Automatic Regeneration
- 10117661Sb-15-003 correction of workshop manual for hino 2015my (revision of troubleshooting procedure for the dtc p0421)
- 10117660Sb-15-002 correction of workshop manual for 2013 - 2015my (revision of troubleshooting procedure for the dtc p2123)
- 10117655SB-14-003 The following is to inform you of the revision of the inspection procedure for the DTC?s P0340 and P0341. You are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to use for servicing.
- 10116069SB - 08 - 005 This document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
- 10116060SB ? 06 - 002 Fuel Filter Usage. This bulletin provides technical information for proper Fuel Filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel filter.
- 10116059SB ? 06 - 001 DESIGN CHANGE OF ENGINE OIL COOLER HOUSING. The casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. These grooves aid in the retention of liquid gasket used during engine production. This changed the appearance of the engine oil cooler housing but does not affect function or applicability.
- 10116057Sb - 05 - 005 proper maintenance procedures for grease lubricated front axles
- 10116055SB ? 05 - 008 This document is to inform the dealers about the addition of the pressure sensor cover and related part for the J08E engine.
- 10116054Sb ? 05 - 007 design change of water pipe for J08E
- 10116053SB - 05 - 003 This document is to inform dealers and workshops on procedures to activate exhaust brake operation.
- 10116052SB ? 05 - 010 CORRECTION TO WORKSHOP MANUALS FOR THE J08E ENGINE. a) Resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 Ohms b) Illustration of the air intake pre-heater terminal should be revised. c) Resistance between terminals of the main relay should be 111 Ohms
- 10116051SB - 05 - 004 SPEEDOMETER RECALIBRATION. This document is to inform of the procedure to calibrate the Pulse Adjust Module whenneeded (ex. tire size change, rear carrier ratio change).
- 1011605005 - 011 CORRECTIONS TO WORKSHOP MANUALS FOR J08 ENGINES. The standard gap between ends of the second piston ring and the oil ring.
- 1011603013-008 Injection Pump Drive Case. Please note the following part number changes to the Injection Pump Bearing Case. Not replacing the correct replacement parts WILL result in major engine damage. The Hino Ordering system has been modified to make the below changes into a kit that consist of the correct parts when ordering the kit ID number. The below information illustrates the kit components per engine and date ranges.
- 10116025PTB 01-08 Complete Engine Assembly Part Numbers
- 10028859Hino trucks: abnormal noise and vibration within the engine occurs due to the impeded operation of the injector needle which IS caused by the formation of deposits in the fuel.
- 10028857Hino trucks: abnormal noise and vibration within the engine occurs due to the impeded operation of the injector needle which IS caused by the formation of deposits in the fuel.
Every Hino NJ8J model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.