2001 Hyundai Accent
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Hyundai › Accent › 2001
These records cover every 2001 Hyundai Accent. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
2 recalls name the 2001 Hyundai Accent. Newest first.
Certain passenger vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 201, "occupant protection in interior impact." during testing, the 3-door hatchback exceeded the performance criterion in the standard midway along the length of the windshield support pillar (a-pillar).
Risk and remedy
Risk
An occupant's head that contacts the a-pillar during a crash could experience an increased risk of a head injury as a result of this condition.
Remedy
Dealers will install new energy management brackets to support the a-pillar covers and increase the energy absorbing performance of the a-pillar in the relevant area. owner notification began october 28, 2002. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact hyundai at 1-800-633-5151.
Vehicle description: passenger vehicles equipped with 1.5 liter or 1.6 liter engines that were originally sold in or currently registered in the states of alaska, colorado, idaho, illinois, indiana, iowa, kansas, maine, massachusetts, michigan, minnesota, missouri, montana, north dakota, nebraska, new hampshire, new york, ohio, pennsylvania, south dakota…
Risk and remedy
Risk
Moisture in the combustion chamber blowby gases may freeze inside the throttle body bore and throttle body idle speed control circuit resulting in the throttle valve not closing fully and a higher than normal idle speed when the accelerator pedal IS released.
Remedy
Dealers will install a new, relocated pcv hose and will additionally install a heated throttle body on the 2000-2001 accents equipped with 1.5 liter engines that were produced through january 31, 2001. owner notification began april 15, 2002. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact hyundai at 1-800-633-5151.
Owner complaints
112 complaints25 involved a crash4 involved a fire20 injuries
What owners report most
Latest complaints
- Suspension
Repair shop did not perform alignment requested on 2001 Hyundai Accent. One reason was: "Cradle is rusted through" Similar recalls exist for Hyundai Elantra (similar design) and Sonata (engine cradle) for same model year. This represents a dangerous condition. Vehicle is operated in Wisconsin, where roads are salted in winter.
- Structure · Suspension
My mechanic told me in april 2020 my 2001 hyundai accent IS not safe to drive because the sub frame has decayed up to were it connects to the body underneath. *tr
- Service brakes · Structure › Body
TL* the contact owns a 2001 hyundai accent. The contact stated that the brake pedal traveled to the floorboard when depressed. The vehicle was taken to an independent mechanic who noticed extensive rusting on the brake lines and was deteriorating. The vehicle was repaired. On another occasion, the…
TL* the contact owns a 2001 hyundai accent. The contact stated that the brake pedal traveled to the floorboard when depressed. The vehicle was taken to an independent mechanic who noticed extensive rusting on the brake lines and was deteriorating. The vehicle was repaired. On another occasion, the vehicle was inspected and it was noticed that there was extensive rust and corrosion near the front of the framing near the front wheels and the motor mount. The mechanic diagnosed that the frame needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 93,000.
- Structure · Structure › Frame and members › Underbody shields · Suspension
Both control arms and drivers side of sub frame completely rotted out. there IS a recall for the 2001-2003 elantra and tiberon, yet not the accent? somebody isn't doing their job!! *tr
- Structure › Frame and members › Underbody shields · Suspension
Front sub frame IS severely corroded between drivers lower control arm and sub frame mount at radiator core support. corrosion has created a hole on each side of the frame rail that will allow for passage of an object similar in size to a deck of cards. passenger side IS similarly corroded. Front…
Front sub frame IS severely corroded between drivers lower control arm and sub frame mount at radiator core support. corrosion has created a hole on each side of the frame rail that will allow for passage of an object similar in size to a deck of cards. passenger side IS similarly corroded. Front sub frame replacement will be necessary in order maintain safe vehicle operation. The degree of front sub frame corrosion IS not in line with the condition of the balance of the vehicle. balance of the vehicle exhibits minimal corrosion. *tr
- Structure › Body
TL* the contact owns a 2001 hyundai accent. The contact stated that the front frame had become severely corroded. The vehicle was not diagnosed or repaired. The manufacturer was not notified. The failure mileage was 64,000.
- Suspension
TL* the contact owns a 2001 hyundai accent. The contact stated that the sub frame and control arms were completely corroded. The vehicle was not repaired and the manufacturer was notified. The approximate failure mileage was 85,000. ...updated 11-12-13 *bf
- Steering · Suspension
Front control arm corroded and broke apart. unable to steer. towed to and confirmed by mechanic. *tr
- Tires
Tire does not have the required dot treadwear, temp. Rates listed on the sidewall. this tire should have that information on it. see nhtsa hotline center; case: tire information; case number: [xxx] for details. information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(B)(6). *tr information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(B)(6). *Tr
- Seat belts
The retractor assembly for the front passenger seatbelt no longer functions properly. An unusual noise IS heard from the assembly when it IS extended or retracted and it fails to lock when the seat belt IS tugged on. I have contacted both my local dealer and hyundai customer service, both refuse to cover any repairs. *tr
- Structure › Body
TL* the contact owns a 2001 hyundai accent. The contact stated that after inspecting the vehicle, he noticed that the sub frame was corroded. The vehicle was taken to the dealer. The technician verified the failure and stated that the sub frame needed to be replaced. The manufacturer was made…
TL* the contact owns a 2001 hyundai accent. The contact stated that after inspecting the vehicle, he noticed that the sub frame was corroded. The vehicle was taken to the dealer. The technician verified the failure and stated that the sub frame needed to be replaced. The manufacturer was made aware of the failure but did not offer any assistance since the vehicle was not included in any recalls. The vehicle was not repaired. The failure and current mileage was 100,000. ..Updated 03-13-13 *bf updated 04/09/2013 *js
- Structure › Body
TL* the contact owns a 2001 hyundai accent. The contact stated that the front frame was completely corroded. The vehicle was inspected by a mechanic, who determined that the failure was a direct result of the salt being used during the winter on the roadways. The manufacturer was made aware of the…
TL* the contact owns a 2001 hyundai accent. The contact stated that the front frame was completely corroded. The vehicle was inspected by a mechanic, who determined that the failure was a direct result of the salt being used during the winter on the roadways. The manufacturer was made aware of the failure and did not offer any assistance since the vehicle was not included in any recalls. The vin was not available. The vehicle was not repaired. The failure and current mileages were 150,000.
- Suspension
TL* the contact owns a 2001 hyundai accent. The contact stated that the vehicle experienced the same failures mentioned in nhtsa campaign ID number: 09v125000 (suspension:front:control arm), including a perforated front lower control arm. The manufacturer was notified and stated that the vin was not included in the recall. The vehicle had not been repaired.the failure and current mileages were 77,000.
- Power train
The transmission slips or doesn't catch from reverse to drive for a few seconds. Also from drive to reverse. *tr
- Air bags › Frontal
2001 hyundai accent. Consumer states airbags deployed without being involved in an accident destroying the windshield and seizing the seat belts *tgw the consumer stated after two months of phone calls, hyundai finally responded and claimed the system detected an impact and no assistance would be provided and the matter was closed. *Jb
- Power train › Automatic transmission · Visibility › Defroster/defogger/hvac system › Rear window
TL* the contact owns a 2001 hyundai accent. The contact stated that the rear window defroster was engaged and when he shut off the defroster, there was a loud explosion sound. The contact then noticed that there was a large hole in the rear window with small web0like fractures surrounding the hole.…
TL* the contact owns a 2001 hyundai accent. The contact stated that the rear window defroster was engaged and when he shut off the defroster, there was a loud explosion sound. The contact then noticed that there was a large hole in the rear window with small web0like fractures surrounding the hole. The window then disintegrated and fell in the rear seat of the vehicle. In addition, the contact stated that when attempting to accelerate, the vehicle was hesitant to engage. The vehicle was not repaired. Neither the dealer nor the manufacturer was contacted in regards to the failures. the failure mileage was approximately 10,000 and the current mileage was 15,955.
- Air bags › Frontal
My family was driving our 2001 hyundai accent in which another vehicle collided with ours except the dash board air bags didn't inflate. Afterwards within two weeks I stopped at the nearest dealership and asked who should I inquire why the air bags didn't work. The vehicle was totaled and I did…
My family was driving our 2001 hyundai accent in which another vehicle collided with ours except the dash board air bags didn't inflate. Afterwards within two weeks I stopped at the nearest dealership and asked who should I inquire why the air bags didn't work. The vehicle was totaled and I did send an email to the address the dealership provided but have heard nothing. My wife and daughter got banged up but are okay now. My concern IS that it could of been much serious and why I haven't heard anything from hyundai. The accident occurred on october 20, 2009 in el centro, california. Thank you. *tr
- Air bags › Frontal
My client was seriously injured when the car her husband was driving struck a telephone pole head-on and the airbags failed to deploy. the airbag system had not given any warning that it was not working at any time before the crash. *Tr
- Engine and engine cooling
Approximately 3000 miles after having a 60,000 mile service involving replacement of all belts, including timing belt using high quality belts of known quality, a high voltage arching condition IS observed on the face of the harmonic balancer (hb). Arch IS approx. .250-.500 inch in length and…
Approximately 3000 miles after having a 60,000 mile service involving replacement of all belts, including timing belt using high quality belts of known quality, a high voltage arching condition IS observed on the face of the harmonic balancer (hb). Arch IS approx. .250-.500 inch in length and projects from the outermost edge of the hb toward the center of same. Using a jumper cable connected to the negative battery terminal, arch can be pulled from the outer edge of harmonic balancer, but no other pulley surface nor belt surface. Condition IS intermittent and forced reproduction has not been possible, but occurs with sufficient frequency to permit troubleshooting. Condition has not been previously observed. After extensive diagnosis, it appears the insulator rubber between mating parts of the hb has degraded resulting in excessive internal resistance which results in static charge generated by belts to escape pulley interior, discharging over the exterior surface. Under the right conditions, this could result in an explosive event should a combustion fuel be present; therefore this should be investigated as a safety issue. Dealer states no knowledge of this being an issue. Replacement hb on order and IS expected in about one week. *Tr
- Suspension › Front
TL* - the contact owns 2001 hyundai accent. while driving at 45 mph on a very nice day the vehicle began drifting on the road. the front passenger tire went off the road and the rear tire went off the road as well. the vehicle slowed down to approximately 40 mph when the driver lost complete…
TL* - the contact owns 2001 hyundai accent. while driving at 45 mph on a very nice day the vehicle began drifting on the road. the front passenger tire went off the road and the rear tire went off the road as well. the vehicle slowed down to approximately 40 mph when the driver lost complete control. he stated that only the driver's side tire was steering correctly, the other tires were going side to side. the contact could not control the vehicle and was rear ended. he sustained minor injuries. the contact had taken some pictures, and said that there was a bolt that sheared off. the rubber bushing was wide open and deformed. the contact had a police report. the current and failure mileage were both 100,000. *ak
- Engine and engine cooling
Dt*: the contact stated while accelerating at various speeds, the engine hesitated, and stalled without warning. the vehicle was inspected by an independent repair shop, who determined the engine coils were worn and needed to be replaced. the manufacturer was alerted.
- Visibility › Windshield wiper/washer
2001 hyundai accent. While in use, the driver's side wiper swung off without warning while driving in rain on 95 north. Wiper was inoperable. The car was taken into the local dealership the next day. The replaced the wiper. The old part IS not available. driver's side wiper swung off again in rain…
2001 hyundai accent. While in use, the driver's side wiper swung off without warning while driving in rain on 95 north. Wiper was inoperable. The car was taken into the local dealership the next day. The replaced the wiper. The old part IS not available. driver's side wiper swung off again in rain while on the road several other times. Each time, the bolt was tightened and the wiper was operable again. in 2006, the wiper swung off again during heavy rain. Was not able to tighten bolt. Took car into dealership. They replaced wiper again. although there were no injuries, there IS no warning when the wiper suddenly swings off during operation. The driver suddenly loses visibility out of the driver's side windshield during heavy rain. *jb
- Power train › Automatic transmission
Car would not reverse, and jerks when shifting from 2-3RD gear. contacted dealer and was told transmission IS completely shot, and must be replaced, at a cost of $2500. found that when shifting from reverse to drive prior car would jolt. *Jb
- Power train › Automatic transmission
Since we bought the car, it has been to the dealership repair shop 5 times, for the same problem. The car begins to have problems shifting gears, it loses power, as not going higher than 20-30 miles. When the gas pedal IS applied, the car gets stuck for several seconds before it jerks and begins to…
Since we bought the car, it has been to the dealership repair shop 5 times, for the same problem. The car begins to have problems shifting gears, it loses power, as not going higher than 20-30 miles. When the gas pedal IS applied, the car gets stuck for several seconds before it jerks and begins to run again. Everytime we take it in they repair the pulse generator. The pulse generator has been changes two time in the last three months alone (june, august), and now its ready to go back into the shop again. It IS getting worse, it IS becoming a safety issue because it gets stuck anywhere, and can get hit from behind, or get into an accident when it stops in the middle of a cross section. *jb
- Electrical system › Alternator/generator/regulator · Engine and engine cooling
Alternator pulley not aligned with crank pulley. tried shimming, tightening and nothing works. causes belt to slip off and car to overheat. car overheated and warped head and collapsed piston rings. engine IS available. *jb
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10251285This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.
- 10247189This bulletin provides important checkpoint guidelines when performing engine oil and filter change services.
- 10235566Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
- 10230904This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
- 10217258Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.
- 10217251Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement.
- 10196546Hyundai approves only the ATF, DCT gear oil and IVT gear oil specified in the vehicles owners manual. Use of other ATF may result in improper shift quality or other drivability conditions. Use of other DCT and IVT gear oil may result in reduced durability. Hyundai does not approve the use of any aftermarket ATF or gear oil additives.
- 10190044This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.
- 10190038This bulletin provides best practice recommendations when performing brake service procedures.
- 10189989This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below.
- 10183963This bulletin describes the procedure to inspect and identify fluid which may appear around the brake caliper area.
- 10183960This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.
- 10178175This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.
- 10176182This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance.
- 10176178This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products.
- 10174808This bulletin provides information on identifying dealer stock vehicles with either: A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. A 30 Day alert - vehicle has not started and reported an SOC in 30 days.
- 10174807The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions:
- 10173546This bulletin describes the general guidelines to disinfect and protect vehicle interior surfaces using certain safe chemical products.
- 10172142This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years.
- 10170883This bulletin provides guidelines to inspect the USB, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.
- 10169370The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.
- 10167253This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.
- 10030984Hyundai: automatic transaxle range switch diagnostic trouble codes p0705 (range switch signal problems), p0707 (range switch open circuit), and p0708 (range switch short circuit or multiple inputs). An improperly adjusted or improperly operating range switch may result in the above mentioned conditions. Malfunction indicator light (mil) illuminated; impossible engine start in p or n.
- 10020913Automatic transaxle diagnostic trouble code (dtc) list.
- 10019362Remanufactured automatic transaxle differential oil seal.
- 10018890Automatic transaxle diagnostic trouble codes list.
- 10018734Reprograms are available for automatic transaxle driveability issues. Technet times. Hyundai.
- 100158532000-2004 1.5L & 1.6L accent p0130 (oxygen sensor) and p0530 (speed sensor).
- 10015733Automatic transaxle diagnostic trouble codes list.
- 10015328Diagnostic trouble code (dtc) p0130 (oxygen sensor malfunction); diagnostic trouble code (dtc) p0503 (speed sensor malfunction; reverse to drive lurch while rolling backwards (on automatic transaxle equipped vehicles only).
- 10014323Fd46xg poly alkylen glycol (pag) oil specifications for air conditioning component replacement.
- 10014315Replacement cigarette lighter.
- 10009777Fd46xg pag oil specifications for air conditioning component replacement.
- 10005268Automatic transaxle pulse generator diagnostic trouble codes p0717 & p0722. 2004 accent included.
- 10004627Slower than usual acceleration after an initial cold start; greater than usual rpm drop when engaging drive or reverse; check engine light on and p0116 stored.
- 10004616Resistance values for idle speed control actuator (isca). Various models including the 2004 sonata.
- 10004469Diagnostic trouble code (dtc) p0722 - pulse generator-b inspection and tcm reprogramming.
- 10003285Shock or delayed engagement during park to reverse or park to drive shift transmission control module (tcm) reprogramming instructions.
- 10002344Ata solenoid diagnostic trouble codes p0740, p0741, p0742, p0743, p0745, p0747, p0748, p0750, p0752, p0753, p0755, p0757, p0758, p0760, p0765.
- 10002065Atm diode pin corrosion in the control wiring harness located behind the dash panel.
Every Hyundai Accent model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.