2013 Hyundai Veloster

Recalls

3 recalls name the 2013 Hyundai Veloster. Newest first.

• Service brakes, hydraulic › Antilock/traction control/electronic limited slip › Control unit/module

  Sep 22, 2023NHTSA 23V6510001,649,478 vehicles

  Hyundai Motor America (Hyundai) is recalling certain 2011-2015 Elantra, Genesis Coupe, Sonata Hybrid, 2012-2015 Accent, Azera, Veloster, 2013-2015 Elantra Coupe, Santa Fe, 2014-2015 Equus, 2010-2012 Veracruz, 2010-2013 Tucson, 2015 Tucson Fuel Cell, and 2013 Santa Fe Sport vehicles. The Anti-Lock Brake System (ABS) module may leak brake fluid internally…

  Risk and remedy

  Risk

  An engine compartment fire while parked or driving can increase the risk of injury.

  Remedy

  Owners are advised to park outside and away from structures until the recall repair is complete. Dealers will replace the ABS fuse, free of charge. Owner notification letters were mailed April 10, 2024 through October 11, 2024. Owners may contact Hyundai customer service at 1-855-371-9460. Hyundai's number for this recall is 251.

  Full recall details →

• Electrical system

  Feb 28, 2023NHTSA 23V13200025,715 vehicles

  Hyundai Motor America (Hyundai) is recalling certain 2012-2014 Veloster vehicles. High conductive liquid may leak into the Reverse Park Aid Sensor (RPAS), which can result in an electrical short circuit.

  Risk and remedy

  Risk

  An electrical short circuit increases the risk of a fire.

  Remedy

  Dealers will inspect and replace the RPAS fuse and sensor, as necessary, free of charge. Owner notification letters were mailed July 28, 2023. Owners may contact Hyundai customer service at 1-855-371-9460. Hyundai's number for this recall is 242.

  Full recall details →

• Electrical system › Software

  Mar 14, 2019NHTSA 19V20400016,487 vehicles

  Hyundai Motor America (Hyundai) is recalling certain 2013 Veloster vehicles that are equipped with 1.6 liter turbo engines. The engine management software may cause premature ignition (pre-ignition) of the air/fuel mixture in the engine. The resulting excessive cylinder pressure may damage the engine.

  Risk and remedy

  Risk

  Engine damage can increase the risk of a fire or cause an engine stall, increasing the risk of a crash.

  Remedy

  Hyundai will notify owners, and dealers will update the engine management software, free of charge. The recall began May 14, 2019. Owners may contact Hyundai customer service at 1-855-371-9460. Hyundai's number for this recall is 182.

  Full recall details →

Owner complaints

What owners report most

1. Engine172
2. Electrical system99
3. Steering59
4. Unknown or other53
5. Power train35
6. Visibility24
7. Fuel/propulsion system22
8. Structure20
9. Service brakes, hydraulic17
10. Vehicle speed control14

Latest complaints

• Oct 28, 2026TN
  Fuel/propulsion system · Unknown or other
  1. COMPONENT FAILED / INSPECTION AVAILABLE: The EVAP canister system failed to retain fuel vapors due to a leak at a structural bracket bolt hole drilled by a technician. The vent valve wiring harness malfunctioned after being physically severed by the shop. All photos, video proof, and OBD2 logs…

  1. COMPONENT FAILED / INSPECTION AVAILABLE: The EVAP canister system failed to retain fuel vapors due to a leak at a structural bracket bolt hole drilled by a technician. The vent valve wiring harness malfunctioned after being physically severed by the shop. All photos, video proof, and OBD2 logs are preserved and available for inspection upon request. 2. SAFETY RISK: Safety was compromised by fuel vapor emissions. The dealer falsified Special Parts Order (SPO) recall records, releasing the vehicle into public operation with an active fuel vapor leak, creating an immediate fire hazard and exposure to toxic fumes. Severing the vent valve wiring rendered emission diagnostics completely non-operational. 3. CONFIRMED BY DEALER/INDEPENDENT: The original canister failure was confirmed by a manufacturer warranty authorization. The failure of the dealer's bracket remedy was confirmed via a home smoke test with clear video evidence of the leak. Physical damage to the electrical harness was visually confirmed via before/after photos taken immediately upon picking up the vehicle. 4. INSPECTION BY OTHERS: Inspected by manufacturer representatives at Twin City Hyundai (Alcoa, TN) under open safety campaigns. The service department falsified safety recall metrics to hide non-compliance, misdiagnosed leaks to solicit $1,100+ in fraudulent repairs, and issued a lifetime service ban to cover up their actions when confronted with proof. 5. WARNING LAMPS & SYMPTOMS: Check Engine Light displayed permanent trouble code P0442 (EVAP small leak). Following the dealer's canister installation and damage to the wiring, a new electrical circuit code triggered immediately. Following my manual repair of the dealer-inflicted harness damage, the permanent P0442 code completely cleared on its own, proving the dealership's diagnosis was fraudulent.

• Oct 15, 2026IA
  Steering

  Clunking sound in steering wheel caused by disintegration of EPS rubber coupler. This is due to a design flaw in the OEM part where the rubber turns gummy.

• Oct 5, 2026TXFire1 injury
  Electrical system · Engine · Service brakes

  My 2013 Hyundai Veloster caught fire spontaneously while it was turned off and parked in my garage. The fire originated in the engine compartment, specifically around the ABS module area. The vehicle has an open and incomplete safety recall for this exact issue (Recall 251 / NHTSA Campaign 23V-651000). The Mission Fire Department responded to the scene to extinguish the fire

• Sep 30, 2026CT194,000 mi
  Air bags
  The contact owns a 2013 Hyundai Veloster. The contact stated that while starting the vehicle, the check engine and air bag warning lights intermittently illuminated. Additionally, the vehicle was driven over deep potholes on the highway, which damaged the steering column and caused the steering…

  The contact owns a 2013 Hyundai Veloster. The contact stated that while starting the vehicle, the check engine and air bag warning lights intermittently illuminated. Additionally, the vehicle was driven over deep potholes on the highway, which damaged the steering column and caused the steering wheel to become loose. The contact filed a Police report after the issue, and the vehicle was towed to an independent mechanic, and it was determined that the driver's side air bag was inoperable and needed to be replaced. The vehicle was being repaired by the insurance company. The failure mileage was approximately 194,000.

• Sep 20, 2026LA
  Electrical system · Service brakes
  My 2013 Hyundai Veloster experienced a catastrophic failure of the ABS module covered under Recall 23V-651 (Campaign 251). The brakes went completely to the floor while operating, and the ABS module is shorting out every replacement fuse, creating an imminent engine fire hazard. Hyundai Corporate…

  My 2013 Hyundai Veloster experienced a catastrophic failure of the ABS module covered under Recall 23V-651 (Campaign 251). The brakes went completely to the floor while operating, and the ABS module is shorting out every replacement fuse, creating an imminent engine fire hazard. Hyundai Corporate has explicitly refused to remedy the underlying defective component causing this fire hazard, only offering to replace the blown fuse. This is a direct failure by the manufacturer to safely remedy a federally recalled defect."

• Aug 31, 2026TX90,000 mi
  Engine
  The contact owns a 2013 Hyundai Veloster. The contact stated that while driving at various speeds on several occasions, abnormal sounds emanated from the engine compartment, and the check oil light illuminated while making left turns. The vehicle was taken to a dealer, where it was diagnosed that…

  The contact owns a 2013 Hyundai Veloster. The contact stated that while driving at various speeds on several occasions, abnormal sounds emanated from the engine compartment, and the check oil light illuminated while making left turns. The vehicle was taken to a dealer, where it was diagnosed that an engine cleaning was needed; however, the service was not performed. The vehicle was later returned to the same dealer, where the same diagnosis was provided. The service was performed, but the failure persisted. The manufacturer was notified of the failure. The failure mileage was approximately 90,000.

• Aug 26, 2026NM
  Unknown or other
  Complaint: Manufacture has not remedied the issue in a timely manner. No incident YET but we limit driving the vehicle because of: Manufacturer Recall Number251 NHTSA Recall Number23V651000 Recall Status Recall Incomplete This recall is from September 22, 2023. It's been nearly 3 years. Our…

  Complaint: Manufacture has not remedied the issue in a timely manner. No incident YET but we limit driving the vehicle because of: Manufacturer Recall Number251 NHTSA Recall Number23V651000 Recall Status Recall Incomplete This recall is from September 22, 2023. It's been nearly 3 years. Our vehicle also has an issue with the headlight constantly going out and the battery being drained. I'm not sure if this is related to this particular recall or just a totally new issue to deal with.

• Aug 3, 2026FLFire
  Service brakes, hydraulic
  The contact's daughter owns a 2013 Hyundai Veloster. The contact stated that while the vehicle was parked, it caught on fire. The vehicle became engulfed in flames, and the authorities were called to the scene. The Fire Department extinguished the fire. The vehicle was later towed to an impound lot…

  The contact's daughter owns a 2013 Hyundai Veloster. The contact stated that while the vehicle was parked, it caught on fire. The vehicle became engulfed in flames, and the authorities were called to the scene. The Fire Department extinguished the fire. The vehicle was later towed to an impound lot where it was deemed a total loss. No injuries were reported. A police report was filed. A nearby roadside electrical box was damaged due to the heat from the fire. Prior to the fire, the vehicle was taken to the dealer to be repaired under NHTSA Campaign Number: 23V132000 (Electrical System). The contact was informed by the dealer that the vehicle did not have a parking sensor, and the recall repair would not apply to the vehicle. Upon investigation, the contact later discovered that the vehicle was included in NHTSA Campaign Number: 23V651000 (Service Brakes, Hydraulic); however, the owner was not made aware of the recall. The manufacturer was not notified of the failure. The failure mileage was unknown.

• Jun 20, 2026AZ
  Electrical system

  Ac selector switch burnt up

• Apr 22, 2026NE
  Engine
  The car goes into limp mode in the middle of driving on the interstate or usually at higher speeds and loses speed quickly. This has put me at high risk for accidents when traveling between cities and has left me stranded on dangerous parts of the interstate at times. I have taken it to my Hyundai…

  The car goes into limp mode in the middle of driving on the interstate or usually at higher speeds and loses speed quickly. This has put me at high risk for accidents when traveling between cities and has left me stranded on dangerous parts of the interstate at times. I have taken it to my Hyundai dealer I bought the car from and they said there is a knock in the engine and the whole engine would need replaced and I cannot afford that ($12k) but the car only has 125k miles on it and I want to keep it for as long as possible because it’s my baby. I do not think it has been inspected by anyone but my dealer yet but I am willing to let anyone look at it in order to get it fixed without paying an arm and a leg. The car did have some issues prior to this issue that were recalled and fixed, but this happened out of nowhere and when it does happen the engine light flashes and it goes into limp mode. The light currently stays on because of the O2 Sensor though, but that is not a big issue. I have to use a OBD2 Scanner to clear the engine knock code every time it goes into limp mode in order to drive it properly and even then it will go back into limp mode eventually. My car started having issues probably a year or two ago. I also want to note I know a girl who used to have the exact same year, make and model of car as me and had the exact same issues of going into limp mode and such so it is not just a random issue of mine.

• Mar 18, 2026NC
  Engine
  As my [XXX] son was driving, his car, out of nowhere, stopped working and the steering wheel became incredibly hard to turn. It put him and other vehicles around him at risk as he was doing 50mph and his car suddenly stalled. No warning. No dash lights. It was hard for him to pull over to safety.…

  As my [XXX] son was driving, his car, out of nowhere, stopped working and the steering wheel became incredibly hard to turn. It put him and other vehicles around him at risk as he was doing 50mph and his car suddenly stalled. No warning. No dash lights. It was hard for him to pull over to safety. We replaced the battery and tried to restart the car, then the engine started smoking. We immediately called for a tow. Our local shop said his engine seized. We then towed it to Hyundai and they confirmed the same thing, "it definitely locked right up." The car has been well taken care of, no warning signs prior to engine failure, no warning lights, etc. His car is also under 100k miles. There is literally no reason for an engine failure. In 2019 there was a NHTSA Recall 19V204, Hyundai Recall #182 ECU Software update; this was supposed to fix the issue but here we are... the engine STILL BLEW. Hyundai is refusing to help. They won't do anything. There's known issues with Hyundai's 1.6 GDI turbo engine. They should be held responsible. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• Feb 27, 2026OH
  Electrical system
  I am writing regarding a serious safety issue with my 2013 Hyundai Veloster, purchased new. Over the life of the vehicle, I have replaced the manual AC/heat control head three times due to repeated failure. During the most recent installation, I left the trim panel off to monitor the wiring…

  I am writing regarding a serious safety issue with my 2013 Hyundai Veloster, purchased new. Over the life of the vehicle, I have replaced the manual AC/heat control head three times due to repeated failure. During the most recent installation, I left the trim panel off to monitor the wiring harness and found it becomes extremely hot while operating. A local repair technician examined it and immediately advised me not to use the heating system due to potential fire risk. Research specific to my vehicle shows documented issues including blower control overheating, burning smell/smoke, burned internal contacts, wiring harness heat damage, and repeat control failure. These match exactly what is occurring with my car. I previously spoke with my dealership’s parts department and was told there may be known concerns involving the wiring harness and blower resistor. I also contacted Hyundai Motor America Consumer Affairs but did not receive assistance. After inspection, the dealership informed me the wiring harness and resistor must be replaced at a cost of approximately $2,450. Given the repeated failures and overheating electrical components, I do not believe I should be responsible for this expense, especially considering the potential safety hazard. The vehicle has been carefully maintained, stored properly, and rarely driven in winter. I had planned to use it for travel after retirement but now feel unsafe operating it. I respectfully request a formal safety review and goodwill repair assistance, as this appears to be a defect rather than normal wear. I am also filing a complaint with the National Highway Traffic Safety Administration due to the documented fire risk. I appreciate your prompt attention to this matter. I am respectfully requesting: A formal safety review of this issue. Goodwill repair assistance or full coverage of the repair costs. Clarification as to whether this issue has been evaluated for recall consideration. [XXX] , [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION

• Feb 24, 2026CA
  Electrical system · Engine · Fuel/propulsion system
  "CATASTROPHIC ENGINE FAILURE & INEFFECTIVE RECALL REMEDY (NHTSA 19V-204): ​While traveling at highway speeds, with my two children and boyfriend, the vehicle went completely black. Car loss complete power, going into a limp mode( 'Loss of Motive Power') The Check Engine Light began flashing before…

  "CATASTROPHIC ENGINE FAILURE & INEFFECTIVE RECALL REMEDY (NHTSA 19V-204): ​While traveling at highway speeds, with my two children and boyfriend, the vehicle went completely black. Car loss complete power, going into a limp mode( 'Loss of Motive Power') The Check Engine Light began flashing before going solid. When I was able to pull to the shoulder, I tried to start the car and noticed the radio screen was black and stayed black(before this time, the screen would some times go blank or completely black and then turn back on). Car would start and shake really hard with noise coming from engine, and then car would die. Since then I have been going back and forth with Hyundai Motors and Hyundai dealer, telling them that this is not a warranty issue, but a safety issue and they both have ignored and didn't enology this at all. This happened October 4th, 2025 Recall of 182 was completed but it failed. The vehicle is at the Dalton Hyundai dealer in Nation City. Dealer confirmed zero compression in engine and want $5000 to tare engine to see if it would be under warranty but I keep telling them this is a safety issue that is still accruing and under the 573 Recall/19v-204 I tried to get help throw the BBB and got denied because of age and being the second owner and they told me to contact NHTSA I am a single mother of two young kids, I bought car on 01/26/25 and still owe money on car. Since 10/4/25 I have had to pay out of pocket for a car rental just get to work. My car is up for repo due to me not able to pay for a rental and my monthly car payment. I am lost and don't know what else I can do to get this matter seen. When buying this car the sale person said it is a good car, it will save money on gas, and it has been a nightmare.

• Feb 19, 2026MO
  Engine
  2013 Hyundai Veloster 2013 turbo had 69000 miles when the engine stalled on the highway and promptly slowed to 40 mph. Midas stated engine blew due to a recall so I had it towed to the closest dealership in Oct 2022. They denied the repair and sent it to corporate for authorization and it was…

  2013 Hyundai Veloster 2013 turbo had 69000 miles when the engine stalled on the highway and promptly slowed to 40 mph. Midas stated engine blew due to a recall so I had it towed to the closest dealership in Oct 2022. They denied the repair and sent it to corporate for authorization and it was denied. Dealership attempted to charge 150 for checking the recall. They then told me to talk to Corporate hyundai. I have went back and forth with them trying to get an explanation for the denial to fix the recall. They wouldn't send the explanation. I refiled the claim again sending them recall laws as well. Recently I received a call from the dealership stating they had the car towed and destroyed. Help

• Jan 29, 2026OH
  Electrical system
  Electrical wiring harness and connector melting and blower transistor overheating with know Hyundai internal documentation, all causing a smoke smell and fire hazard. I'm on my 3rd manual Heater / HVAC Control Unit. Fire risk acknowledged by Hyundai dealership and customer affairs. Forced to pay…

  Electrical wiring harness and connector melting and blower transistor overheating with know Hyundai internal documentation, all causing a smoke smell and fire hazard. I'm on my 3rd manual Heater / HVAC Control Unit. Fire risk acknowledged by Hyundai dealership and customer affairs. Forced to pay diagnostics fees despite know safety issues, Cost for repairs out the door around 2,450 out the door. Car sitting at the Hyundai dealership waiting for me to repair or not. I cant be driving a fire hazard vehical.

• Jan 1, 2026MO
  Engine
  Purchased car from Premier Auto in Kansas City, KS in January of 2023. The car had 70,000 miles on it. In July of 2023 I was driving on a 4 lane HWY with a speedlimit of 65. The car suddenly jerked to and slowed to 35 MPH. The car behind me nearly hit me. I had it towed to Midas to have it…

  Purchased car from Premier Auto in Kansas City, KS in January of 2023. The car had 70,000 miles on it. In July of 2023 I was driving on a 4 lane HWY with a speedlimit of 65. The car suddenly jerked to and slowed to 35 MPH. The car behind me nearly hit me. I had it towed to Midas to have it checked out. They informed me the engine had failed and it was because of a manufacturer recall. I then had it towed to a Hyundai dealership in October 2023. They stated to me that it was engine failure due to a recall but they would not fix it. They stated not under recall. The dealership then sent me a notice saying that I owed them 150 dollars and they would keep the car. I filed a claim with Hyundai corporate and they denied repairs stating not under warranty. I appealed that which was a denied response with the reason as not under warranty. I then filed a claim with BBB warranty department and their response was "we only assist with new car warranty issues. I then filed another claim with Hyundai corporate and the dealership and both denied it because of the warrant expiration. While that was happening I lost my spouse of 23 years. The car has been at the dealership for 2.5 years now and I continue to submit requests that are continuously denied.

• Dec 29, 2025NY123,000 mi
  Visibility › Defroster/defogger/hvac system
  The contact owns a 2013 Hyundai Veloster. The contact stated that the highest dial setting of the A/C unit had failed to operate as needed. Upon repairing the dial setting on his own, the contact discovered that the dial had burned out. The contact stated that after the repair, the failure recurred…

  The contact owns a 2013 Hyundai Veloster. The contact stated that the highest dial setting of the A/C unit had failed to operate as needed. Upon repairing the dial setting on his own, the contact discovered that the dial had burned out. The contact stated that after the repair, the failure recurred nearly a week later. The contact discovered that the dial had burned out again. The dealer was notified of the failure, and the contact was given an estimate for a diagnostic test. The contact stated that failure had caused the defrost system to function poorly, which reduced the road's visibility while driving. The vehicle was not repaired. The manufacturer had yet to be notified of the failure. The failure mileage was approximately 123,000.

• Sep 30, 2025MO100,000 mi
  Engine
  The contact owns a 2013 Hyundai Veloster. The contact stated that while driving at 70 MPH, the vehicle stopped and failed to accelerate. There were no warning lights illuminated. The vehicle was towed to the local dealer, where it was diagnosed and determined that the engine needed to be replaced.…

  The contact owns a 2013 Hyundai Veloster. The contact stated that while driving at 70 MPH, the vehicle stopped and failed to accelerate. There were no warning lights illuminated. The vehicle was towed to the local dealer, where it was diagnosed and determined that the engine needed to be replaced. The vehicle was not repaired. The dealer informed the contact that there was no special warranty coverage on the vehicle for the repair. The manufacturer was not contacted. The failure mileage was approximately 100,000.

• Sep 2, 2025NCFire
  Electrical system · Engine · Unknown or other
  On or about May 1, 2025, I was operating my 2013 Hyundai Veloster when flames were observed emanating from under the hood. I immediately pulled into the median and, upon opening the hood, observed an active fire beneath the plastic engine cover. I contacted 911. Before the fire department arrived…

  On or about May 1, 2025, I was operating my 2013 Hyundai Veloster when flames were observed emanating from under the hood. I immediately pulled into the median and, upon opening the hood, observed an active fire beneath the plastic engine cover. I contacted 911. Before the fire department arrived, a passerby extinguished the flames with a fire extinguisher. Firefighters from a nearby station arrived shortly thereafter and fully doused the engine compartment. The vehicle was subsequently towed to a Hyundai dealership. At that time, I was aware of an active recall related to potential brake line issues that could result in an engine compartment fire. After the vehicle remained at the dealership for an extended period, I was informed that Hyundai Motor America (“HMA”) would send an inspector. Approximately 30 days later, I was contacted by HMA’s corporate office and asked to provide documentation, including a copy of the title and insurance information. During this call, I was advised that while repair or replacement of the vehicle was unlikely, HMA would “make me whole.” Shortly thereafter, I received written correspondence from HMA stating that, following its review of the inspection results, documents, and other information, no product defect was identified as the cause of the incident. The letter concluded that HMA would not accept responsibility and denied my request for assistance or compensation.

• Aug 16, 2025TXFire
  Electrical system

  Smoke, burning smell came from ac control unit. Ac wiring unit, knob completely burned/melted. Reported to Hyundai local and corporate office no resolution other then I just have to replace the unit. Please note this happened in 2022 (40,000 miles today vehicle had 58,000miles) and I paid in full for the replacement the 1st time.

• Jul 18, 2025FL
  Engine
  While driving under normal conditions at approximately 65 mph, the engine emitted a sudden “bang” and severe knock. Over the following week, the vehicle stalled several times. Inspection revealed one piston crown was chipped, which then scored the cylinder wall and caused an oil leak. No other…

  While driving under normal conditions at approximately 65 mph, the engine emitted a sudden “bang” and severe knock. Over the following week, the vehicle stalled several times. Inspection revealed one piston crown was chipped, which then scored the cylinder wall and caused an oil leak. No other pistons or bearings showed wear. This failure pattern is consistent with low‐speed pre-ignition events documented in numerous online owner reports—many describing identical piston or rod breakage in 2013–2015 Veloster Turbos under Recall 19V204000, which addresses exactly this defect. The vehicle was partially disassembled for inspection, and Hyundai dealers have refused to perform the federally mandated Recall 19V204000 remedy. Instead, they deceptively insist on treating this as a warranty work request—despite me having told them more than five times (on multiple recorded calls), in two portal updates, and via certified letters, that this is a safety recall issue, not a warranty claim. Their refusal has forced me to incur several thousand dollars worth of expenses and spend dozens of hours pursuing a remedy. Hyundai representatives have repeatedly argued that this engine malfunction may stem from previous accident damage. However, the vehicle’s only collisions occurred in June 2014, when it sustained moderate to severe front-end damage at approximately 1,000 miles and was subsequently repaired at a certified dealer, and in 2019, when it incurred rear-end damage under 30,000 miles. The piston-crown failure I experienced in 2024—at 90,000–95,000 miles—cannot be attributed to either of those incidents. Its nature and timing are fully consistent with low-speed pre-ignition, the exact defect addressed by Recall 19V204000. An 11-page CARFAX report and full call‐recordings are available upon request.

• Jun 25, 2025NH
  Engine
  My 2013 Hyundai Veloster (VIN: [XXX] ) has the known P1326 fault related to the Theta II engine defect. Despite a rod bearing test that passed, the engine now requires replacement, confirmed by the dealer, who quoted me $8,494. Hyundai refuses to assist, even though I am under the 150,000-mile…

  My 2013 Hyundai Veloster (VIN: [XXX] ) has the known P1326 fault related to the Theta II engine defect. Despite a rod bearing test that passed, the engine now requires replacement, confirmed by the dealer, who quoted me $8,494. Hyundai refuses to assist, even though I am under the 150,000-mile extended warranty. This is a safety risk and fits the class-action defect criteria. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• Jun 25, 2025NH
  Engine
  Vehicle Info: 2013 Hyundai Veloster VIN: [XXX] Odometer: 75,000 miles Problem Description: My check engine light began flashing and the vehicle entered limp mode. Diagnostic codes showed P1326 and U1103, which are linked to a known Theta II engine defect involving rod bearing failure. Hyundai…

  Vehicle Info: 2013 Hyundai Veloster VIN: [XXX] Odometer: 75,000 miles Problem Description: My check engine light began flashing and the vehicle entered limp mode. Diagnostic codes showed P1326 and U1103, which are linked to a known Theta II engine defect involving rod bearing failure. Hyundai issued a 15-year / 150,000-mile warranty extension and settled a class-action lawsuit to cover these failures. However, my request for coverage was denied due to “time in service” despite being well below the mileage limit (only 75k miles). This is a serious safety concern that may result in sudden engine failure. I am requesting that NHTSA investigate Hyundai's denial and handling of such cases INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• Jun 9, 2025OK
  Service brakes, hydraulic

  See attached document for complaint.

• Jun 4, 2025PA
  Electrical system
  The knob for the A/C can not handle the amperage when in the 4 position, it gets too hot, melts, and shuts off the system. It is available for inspection. Hyundai is acutely aware of this problem and recalled it in other years, the same as their junk engines, but once again the owners of the 2013…

  The knob for the A/C can not handle the amperage when in the 4 position, it gets too hot, melts, and shuts off the system. It is available for inspection. Hyundai is acutely aware of this problem and recalled it in other years, the same as their junk engines, but once again the owners of the 2013 are left out in the dark. This is a fire hazard that the manufacturer is trying to sweep under the rug, there are service bulletins out on it for other years.

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Hyundai and Kia ABS Module Fires

  AQ23002Opened Nov 17, 2023Open
  The Office of Defects Investigation (ODI) has received eight Hyundai Motor America (Hyundai) and eight Kia America, Inc. (Kia) Part 573 Recall Reports between 2016 and 2023. The combined 16 safety recalls all involve the antilock braking system (ABS) modules or Hydraulic Electronic Control Units (HECU) manufactured by…

  The Office of Defects Investigation (ODI) has received eight Hyundai Motor America (Hyundai) and eight Kia America, Inc. (Kia) Part 573 Recall Reports between 2016 and 2023. The combined 16 safety recalls all involve the antilock braking system (ABS) modules or Hydraulic Electronic Control Units (HECU) manufactured by the equipment supplier Mando. The Part 573 Recall Reports contain varying defect descriptions and differing remedy descriptions for the same or similar equipment supplied by Mando. Safety recalls included in this Audit Query (AQ) review include: Hyundai recalls 20V-520, 20V-543, 21V-161, 21V-160, 21V-303, 22V-056, 22V-810, and 23V-651. Kia recalls 16V-815, 20V-518, 20V-519, 21V-137, 21V-331, 22V-051, 22V-800, and 23V-652 The purpose of this AQ is to evaluate the timeliness and scoping of Hyundai and Kia’s defect decision making and adherence with reporting requirements; and understand the varying defect descriptions and remedies between these recalls.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11006829Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
• 11000788A class settlement against Hyundai Motor America (HMA) that had alleged that certain 2011 2022 model year Hyundai vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.
• 11000314A class settlement against Hyundai Motor America (HMA) that had alleged that certain 2011 2022 model year Hyundai vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.
• 10253275This TSB provides a procedure to diagnose and replace, if necessary, an automatic transmission with Incorrect Ratio DTC (transmission clutch slip in gear above limit) listed on Page 2.
• 10251285This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.
• 10251282Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.
• 10251276This bulletin provides the service procedure to: 1) Upgrade the IBU/BCM (Integrated Body Control Unit/Body Control Module) to revise the OEM Hyundai burglar alarm system operation and ignition start logic and 2) Install two anti-theft decals for the front windows. Additional decals may also be installed in the rear windows at customers discretion.
• 10251275Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealers.
• 10249707Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
• 10247611Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
• 10247189This bulletin provides important checkpoint guidelines when performing engine oil and filter change services.
• 10245579Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
• 10245578Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
• 10244992Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
• 10241874Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
• 10241849Some models from service campaign 993 (IBU/BCM Software Update and Decals Application) equipped with the Hyundai OEM remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.
• 10240082A class action lawsuit against Hyundai Motor America (HMA) alleges that certain Hyundai vehicles (Class Vehicles) were manufactured, marketed, sold, and/or leased with an engine defect that can result in sudden engine seizure, stalling, engine failure, and in some circumstances, engine fire, and that some owners and lessees of Class Vehicles have been improperly denied repairs under warranty. Neither HMA nor Hyundai Motor Company have been found liable for any of the claims alleged in the lawsuit. The parties have instead reached a voluntary settlement (the Settlement) to avoid lengthy litigation and to provide owners of Class Vehicles certain benefits.
• 10240081Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32).
• 10240080Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
• 10238353Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
• 10237189Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
• 10235566Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
• 10235556Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
• 10235555Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993) in response to an increase in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.
• 10235341Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
• 10233549Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993) in response to an increase in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.
• 10233547Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
• 10230904This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
• 10228219In certain areas, a vehicles underbody may exhibit corrosion due to road-salt usage. As a preventative measure, a cavity wax coating is applied to the internal surfaces of underbody components and an undercoating spray is applied to exterior surfaces of specified underbody components. This bulletin describes the procedure to perform this preventative service on certain 2012 2017MY Velosters (FS).
• 10228218In certain areas, a vehicles underbody may exhibit corrosion due to road-salt usage. As a preventative measure, a cavity wax coating is applied to the internal surfaces of underbody components and an undercoating spray is applied to exterior surfaces of specified underbody components. This bulletin describes the procedure to perform this preventative service on certain 2012 2017MY Velosters (FS).
• 10227320Certain vehicles may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit abnormal noise, or no crank/no start condition related to connecting rod bearing wear or damage. This Dealer Best Practice outlines the service process to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results, as well as related warranty coverage for the conditions outlined above.
• 10227317Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.
• 10227316The warranty coverage for engine repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners. Commercial entities and individuals engaged in the buying, selling, leasing, or renting of motor vehicles, as well as salvaged vehicles, are ineligible for the extended warranty.
• 10227313Op code/part number (reference guide for service campaign T6G)
• 10217258Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.
• 10217251Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement.
• 10211675The Powertrain warranty coverage for certain engine repairs and/or replacement where the engine damage or malfunction is related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
• 10211667Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
• 10211666Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.
• 10211664Hyundai is conducting a service campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

Every Hyundai Veloster model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.