2005 Infiniti Q45

Recalls

3 recalls name the 2005 Infiniti Q45. Newest first.

• Air bags › Side/window

  Feb 28, 2012NHTSA 12V0790001,349 vehicles

  Nissan IS recalling certain model year 2003-2005 infiniti Q45 vehicles. a wiring connector for the seat mounted airbag may experience increased electrical resistance, resulting in the non-deployment of the side air bags.

  Risk and remedy

  Risk

  Non-deployment of side air bags could increase the risk of personal injury.

  Remedy

  Nissan will notify owners, and dealers will modify the wiring connector, free of charge. the safety recall began on march 19, 2012. owners may contact nissan customer service at 1-800-647-7261.

  Full recall details →

• Exterior lighting › Brake lights

  Oct 13, 2006NHTSA 06V3950001,863 vehicles

  Certain vehicles fail to comply with the stop lamp and reflex reflector requirements of federal motor vehicle safety standard no. 108, 'lamps, reflective devices, and associated equipment."

  Risk and remedy

  Risk

  This standard IS to reduce crashes, injuries and deaths by providing adequate illumination of the roadway, and by enhancing the conspicuity of motor vehicles on the public roads so that their presence IS perceived and their signals understood, both in daylight and in darkness or other conditions of reduced visibility.

  Remedy

  Dealers will replace the rear combination lamp assemblies free of charge. the recall IS expected to begin on or about april 16, 2007. owners may contact infiniti at 1-800-662-6200.

  Full recall details →

• Child seat › Latch strap

  Aug 29, 2005NHTSA 05V374000167 vehicles

  Certain passenger vehicles equipped with power rear seats fail to conform to the requirements of federal motor vehicle safety standard no. 225, "child restraint anchorage systems." the lower anchorage brackets in the rear seats do not meet the location requirement in this standard. this may cause difficulty in attaching some child seats to these…

  Risk and remedy

  Risk

  If a child seat IS not secured, there IS an increased risk of injury in a crash.

  Remedy

  Dealers will replace the lower anchorage brackets with modified ones to ensure that the standard IS met. the recall began on october 17, 2005. owners may contact infiniti at 1-800-662-6200.

  Full recall details →

Owner complaints

What owners report most

1. Air bags1
2. Electrical system1
3. Seats1
4. Tires1
5. Vehicle speed control1

Latest complaints

• Jan 26, 2019TN87,000 mi
  Vehicle speed control
  When cruise control IS set, and the need to pass or speed up IS required, if you press the gas pedal to the floor the car takes off and *then stops responding and drops back to set cruise control speed while you are still flooring it. It bucks back and forth. I spoke to several owners on a infiniti…

  When cruise control IS set, and the need to pass or speed up IS required, if you press the gas pedal to the floor the car takes off and *then stops responding and drops back to set cruise control speed while you are still flooring it. It bucks back and forth. I spoke to several owners on a infiniti owners site and theres performs the same. Its dangerous if the need to speed up occurs. This IS a problem in the coding of the parameters in the ecu and could be deadly with unexpected performance. This happened on I40 in knoxville tennessee in heavy traffic. This condition can be repeated back to back multiple times.

• Jun 20, 2012SC117,000 miCrash1 injury
  Air bags · Seats
  TL* the contact owns a 2005 infiniti Q45. The contact stated that while driving 35 mph, another vehicle crashed into her passenger side. The air bags did not deploy and the front driver's seat twisted toward the driver's door during the crash. The contact suffered injuries and was taken to the…

  TL* the contact owns a 2005 infiniti Q45. The contact stated that while driving 35 mph, another vehicle crashed into her passenger side. The air bags did not deploy and the front driver's seat twisted toward the driver's door during the crash. The contact suffered injuries and was taken to the hospital. The vehicle was towed to the contact's home. The failure was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was 117,000.

• Jan 14, 2011FL81,600 mi
  Tires
  I purchased 4 new tires for my vehicle on 7/24/2010 the tires in question are michelin p245/45r18 primacy MXV4 96V. After only 3500 miles the rear right tire blew on the highway, fortunately for me there was heavy traffic and I was not doing over 30mph. The tire was replaced with the spare tire and…

  I purchased 4 new tires for my vehicle on 7/24/2010 the tires in question are michelin p245/45r18 primacy MXV4 96V. After only 3500 miles the rear right tire blew on the highway, fortunately for me there was heavy traffic and I was not doing over 30mph. The tire was replaced with the spare tire and then it was discovered a 3" gash from the side wall to the first thread. No foreign objects were found in the tire to suggest that I picked something on the road,however I did notice that the reinforcements were ripped I am concerned about the safety of these tires and have kept the damaged tire for inspection for anyone who may want to investigate. Thank you. *Tr

• Oct 17, 2007MD17,000 mi
  Electrical system › Ignition

  Tl*the contact owns a 2005 infiniti Q45. while the vehicle was parked, the contact attempted to start the vehicle; however, the key would not turn in the ignition. she called aaa to get the vehicle to start. the vehicle was taken to the dealer for service, but no failures were found at that time. the current mileage was 28,000 and failure mileage was 17,000. Updated 01/02/08. *lj updated 12/12/07 *tr

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Non-deployment of Side Thorax Air Bags

  EA09005Opened Apr 1, 2009Closed Apr 3, 2012Recall 12V079000
  The subject vehicles are equipped with seat-mounted, side thorax air bags for the driver and front passenger.This investigation revealed that faulty side air bag module electrical connectors located under the driver and front passenger seats can cause an interruption in the electrical circuit that will drop the input…

  The subject vehicles are equipped with seat-mounted, side thorax air bags for the driver and front passenger.This investigation revealed that faulty side air bag module electrical connectors located under the driver and front passenger seats can cause an interruption in the electrical circuit that will drop the input voltage below the specified range.As a result, the air bag warning lamp illuminates on the instrument panel and the affected side air bag becomes deactivated.In June 2009, Nissan conducted a service campaign to repair the defective air bag electrical connectors in the subject vehicles (both Infiniti Q45 and M45 models).In June 2010, Nissan sent a second notification concerning the 2009 campaign to owners of vehicles that have not been remedied.Nissan is now conducting a safety recall of the Q45 vehicles not remedied under the service campaign (approximately 1,349 vehicles; see NHTSA Safety Recall No. 12V-079 for further details).The M45 vehicles are not included in the recall; however, Nissan is re-notifying owners of M45 vehicles that were not remedied under the previous service campaign.See attached report for more information.A safety-related defect trend has not been identified in the Infiniti M45 vehicles at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.The ODI reports cited above can be reviewed online at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers: 10327196 and 10402282

• Side air bag non-deployment

  PE08067Opened Dec 2, 2008Closed Apr 1, 2009
  The subject vehicles are equipped with seat-mounted, side torso air bags for the driver and front passenger.this investigation has revealed that faulty side air bag module connectors located under the front seats can cause an interruption in the electrical current that will drop the input voltage below the specified…

  The subject vehicles are equipped with seat-mounted, side torso air bags for the driver and front passenger.this investigation has revealed that faulty side air bag module connectors located under the front seats can cause an interruption in the electrical current that will drop the input voltage below the specified range.as a result, the air bag warning lamp illuminates and the affected side air bag IS deactivated.the rates of complaints, field reports and warranty claims related to the subject issue are very high.for example, nissan submitted 4,853 warranty claims on 3,551 distinct subject vehicles out of 13,836 total subject vehicles.also, analyses of warranty claims indicate an increasing failure trend over time.this preliminary evaluation has been upgraded to an engineering analysis (ea09-005) to further study the issue.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11002539INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 11002537CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 11001653CAN COMMUNICATION CODES DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 11001182WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 11001179REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 11001177WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 10233611ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 10232646REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 10232645WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 10232644WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 10208930CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 10207844CAN COMMUNICATION CODES DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 10192822SERVICE INFORMATION Replacement 5-speed rear wheel drive Automatic Transmission (A/T) assemblies and replacement control valves (valve bodies) now come with blank Transmission Control Modules (TCMs). Blank TCMs come without software and must be programmed (not reprogrammed) and then configured after they are installed. When ordering a replacement A/T or control valve, use the Infiniti electronic parts information systems to obtain the correct software program part number See this bulletin for further detail.
• 10192806IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location, ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
• 10192802SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Infiniti by request if certain criteria are met. This bulletinlists the criteria and provides an application form for such replacements. See this bulletin for further detail.
• 10192728SERVICE INFORMATION The purpose of this bulletin is to give Infiniti dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
• 10192693SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulleitn for further details.
• 10192639SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
• 10192589SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
• 10192514SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Infiniti STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
• 10192505SERVICE INFORMATION Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.infinitinavigation.com and is mailed update disc(s) or SD card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
• 10192475SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
• 10192314SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
• 10192235Infiniti Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Infiniti design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Infiniti's standards. Infiniti Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Infiniti most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletin for further details.
• 10192232SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulletin for further details.
• 10192219SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. See this bulletin for further details.
• 10192218If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see ITB00-024). See this bulletin for further detail.
• 10192191As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
• 10192146SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
• 10190150INFINITI; FRONT SONAR PARKING SENSOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 10190026NAVIGATION MAP DATA UPDATE MATRIX This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
• 101853752005-2015 INFINITI VEHICLES; ECM REPROGRAMMING SERVICE INFORMATION This bulletin is no longer active. Please discard previous versions of ITB15-024.
• 10160176EXTERIOR CLEANING INFORMATION SERVICE INFORMATION When cleaning the exterior of an Infiniti vehicle, damage may occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.
• 10149809PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT: All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.
• 10149806TRANSMISSION & ENGINE AUTOMATED DATA COLLECTION AND DIAGNOSTIC REPORTING SERVICE INFORMATION To support proper diagnosis and to promote Fixed-Right-First-Time ? Infiniti may review CONSULT-III plus (CIII plus) data relating to vehicle operation and function to help with vehicle diagnosis and diagnostic validation. IMPORTANT: For transmission/engine repair or replacement, retailers are required to connect C-III plus and perform ?Diagnosis (All Systems)?. Performing C-III plus ?Diagnosis (All Systems)? is also required prior to contacting any Infiniti call center (i.e. TECH-LINE, PCC, or WCC) for diagnostic support or claim preauthorization. NOTE: For additional information regarding Automated Vehicle Data Collection, refer to IWBI/18-019. To support Automated Vehicle Data Collection, your C-III plus must have the Diagnosis result reporting function-Setting turned ON. If Diagnosis result reporting function-Setting is OFF: - It may cause dealer consideration for Audit or the Anomalous Repair Control (ARC) program, where applicable. - It may result in a repair being non-warrantable. Refer to the Service Procedure on the next page to confirm your C-III plus ?Diagnosis result reporting function-Setting? is turned ON.
• 10149803Infiniti USA Electronic Field Communication Subject: Takata Completion Objectives for Q3 INFINITI is continuing to ask its retailers to urgently help increase customer participation in the Takata recalls to help it achieve 100% customer recall participation for the following vehicles: ? 2001 I30 ? 2002-04 I35 ? 2003-08 FX ? 2002-03 QX4 ? 2006-10 M Sedan INFINITI expects to upload the next refreshed owner list to DBS within the next week. We will also be reassigning VINs to retailers based on information changes. We didn?t reassign any VINs in Q2 to avoid any mid-quarter objective impact. If VINs were repaired out of network, the retailer/region with the original assignment received credit for the repair. This is an extremely serious safety issue and INFINITI is taking significant and unprecedented steps to increase client recall participation but it needs retailer help to achieve its remedy goals. A separate communication will be released later this month informing regional personnel of the requirements for bonus payout in Q3 and Q2 results. The Q3 objective is based on the average number of repairs in Q2 multiplied by the number of service days in Q3 (Mon-Sat minus any holidays). Retailer engagement is critical with this effort. It is a company-wide responsibility to make it a priority to replace these dangerous airbag inflators in affected vehicles. Further, increasing recall participation represents significant gross profit opportunity for our retailers.
• 10149802Infiniti USA Electronic Field Communication Subject: Retailed Vehicle Open Campaign Report Lists Updated The lists for each retailer?s Retailed Vehicle Open Campaign Report has been updated today in DBS. We made our best effort to reassign vehicles to retailers based on the most recent owner information we received. The complexity of filtering out brokers (banks, salvage yards, and insurance companies) and reassigning VINs based on updated owner information affected over 123K records between INFINITI and Nissan, so we are unable to summarize the changes at a regional or retailer level. We suggest the retailers download their lists and have their outbound call centers compare information if necessary. If you have questions, please let us know. Additionally, we will have some enhancements coming in DBS effective November 17, 2018: Owner Data Updates (NNA side): 1. VIN, Campaign Code, and Source are the unique fields 2. Compare all fields except Remove Flag and Comments to see if there is a difference. a. If there is same VIN, Camp ID, and Source and all other fields are also the same then the record will be updated without changing Remove Flag and Comment field b. If there is same VIN, Camp ID, and Source and any other field is different, then the record will be inserted, in this case Remove Flag and Comment field will be blank as this is new record. The remove flag is being removed so the retailer will understand the information they previously flagged for removal has been updated and should be tried again before reapplying the removal flag. c. The retailer benefit of A & B above is duplicate records for the same VIN, Camp ID, and information source with the same customer contact information will no longer display in DBS on the Retailed Vehicle Open Campaign Report.
• 10145541DBS Enhancement: Retailed Vehicle Open Campaign Report INFINITI announced the availability of a new DBS enhancement tool to the Service > Campaign screen: Retailed Vehicle Open Campaign Report on July 9, 2018, which identifies owner contact information for specific campaigns. Currently, only Takata campaign owner lists are available. The following personnel will have access to this tool: - Retailer: Dealer Principal, Executive Managers, General Managers, Parts/Service Managers, and/or Parts/Service Directors - Regions: Regional Aftersales Manager (RAM), Regional Operations Managers (ROM), Fixed Operations Manager (FOM), Dealer Operation Managers (DOM), Regional Service Operation Managers (RSOM), and Client Experience Managers (CEM) The report can be viewed on screen or exported to Microsoft Excel and identifies the following: - VIN - Campaign ID & Campaign Description - Model & Model Year - Data Source o Up to three data sources can be provided for each VIN - RO Info: If this VIN has visited an Infiniti retailer anywhere in the U.S. within the last twelve months, the RO information will be displayed. - Campaign Mailing List: This is DMV data for the VIN listed - Marketing List: If an owner is on your marketing list, their contact information from that list will be displayed here. DMV data is not used for marketing list owner information. - Contact Name - Last Name/First Name & Address (City, State, Zip) - Phone (1-3) & Email (1-3) - Remove Flag o This defaults to ?N? unless the retailer or INFINITI USA flags this VIN for removal. o The removed information will still show on the DBS screen and exported report, but can be filtered on the exported file to only display the records with ?N? in this column.
• 10145053OBD II EVAP Tube Warranty Enhancement UPDATE August 17, 2018 Please discard earlier versions of this bulletin. The announcement from March 21, 2017 has been revised to include: - Clarification that the refueling concern is extremely hard to fill, not intermittent, and occurs at multiple fueling stations and fuel pumps - Customer expense may be applicable if the vehicle is out of warranty
• 10145052OBD II EVAP Tube Warranty Enhancement UPDATE August 17, 2018 Please discard earlier versions of this bulletin The announcement from March 21, 2017 has been revised to include: o Clarification that the refueling concern is extremely hard to fill, not intermittent, and occurs at multiple fueling stations and fuel pumps o Client expense may be applicable if the vehicle is out of warranty

Every Infiniti Q45 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.