2018 International Transtar
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › International › Transtar › 2018
These records cover every 2018 International Transtar. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
2 recalls name the 2018 International Transtar. Newest first.
Navistar, Inc. (Navistar) is recalling certain 2019 International HV, MV, 2018-2019 HX, LT, RH, LoneStar, ProStar, WorkStar, and 2018 TranStar automated manual transmission vehicles, equipped with certain Eaton ECA heavy-duty truck clutches. An internal component in the clutch assembly may fail, possibly resulting in unintended vehicle movement.
Risk and remedy
Risk
Unintended vehicle movement can increase the risk of a crash.
Remedy
Navistar will notify owners, and dealers will recalibrate the Transmission Control Module (TCM), free of charge. The recall began January 18, 2019. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for this recall is 18518.
Navistar, Inc. (Navistar) is recalling certain 2018-2019 International WorkStar, DuraStar, LoneStar, LT, ProStar, RH and IC Bus HC, 2018 International TranStar, 2019 International HV and MV trucks and transit buses. The front driver and passenger seat belt anchor D-ring bolt may break in the event of a crash. As such, these vehicles fail to comply with…
Risk and remedy
Risk
If the D-ring bolt breaks during a crash, the seat occupant may not be properly restrained, increasing their risk of injury.
Remedy
Navistar has notified owners, and dealers will replace the D-ring bolt depending on the information found on the seat belt label, free of charge. The recall began May 23, 2018. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for this recall is 18505.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010428This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
- 10253960This document covers battery diagnostics, maintenance and storage requirement.
- 10251414Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine.
- 10251409Suggested alignment target values when performing a vehicle axle alignment.
- 10246231J1939 Data Link Source Address Information
- 10244926Rebuilding Cylinder Heads on Certain MaxxForce 11/13, N13, and A26 engines; 2010 to present.
- 10243610How to request a horsepower quote; all International and Cummins engines
- 10243596General Wheel Speed Sensor Troubleshooting
- 10243595Diagnosis of chassis wander complaints.
- 10243594Certain International N13 engines may be noncompliant to the required On Board Diagnostics (OBD) Monitor, Manufacturers Self-Test (MST) for over-boost, Exhaust Gas Recirculation (EGR) low flow, and EGR high flow monitors. Under certain conditions, this noncompliance may result in the failure to detect an increase in regulated air pollutants.
- 10241555J1939 Data Link Source Address Information
- 10241554J1939 Data Link Troubleshooting
- 10240193Snap-On torque wrench requirement for all big bore engine connecting rod bolts; A26, MaxxForce 13, N13 engines
- 10238858QLS Emergency Calibration Revert Process
- 10237468New air compressor incorporates an oil feed dowel O-ring. Only models equipped with 2010 and newer MaxxForce 11/13 engines, all N13, and A26 engines
- 10236042New Air compressor Incorporates an oil feed dowel O-ring; only models built with MaxxForce 11/13, N13, or A26 Engines
- 10234021Rebuilding cylinder heads on certain EPA 2010 MaxxForce 11/13, N13, and A26 Engines
- 10234015Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
- 10234007Telematics installation guidelines - Only units with 500K data link
- 10234000Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI engines or Cummins ISB engine with Allison transmissions
- 10232616Rebuilding Cylinder Heads on Certain International MaxxForce 11/13 engines and all International N13 and A26 engines
- 10231068QLS Emergency ECM Calibration; only models equipped with Cummins B6.7, X15, L9, or International A26 engines
- 10227455J1939 Data link source address information
- 10227446QLS Emergency Calibration. applies to 2016 and newer Cummins B6.6, X15, and L9 engines and all A26 engines
- 10222490Pico Scope CCOS (Crankcase Separator Test)
- 10219330PicoScope Test One Channel RCT
- 10219328PicoScope Wheel Speed Sensor Test
- 10219325PicoScope Test Resistance and Ohmmeter
- 10219319PicoScope Test for Datalink (CAN) Health Shorts & opens
- 10219314PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
- 10219308PicoScope Test 12V Electrical Noise Detection
- 10219307PicoScope Test 5V & 12V Intermittent Open and Short circuit diagnostics
- 10215243Cab water leak trouble shooting tips
- 10209484Cab water leak troubleshooting tips; HX with steel cab only
- 10208431J1939 Data Link Source Address Information
- 10206043High Pressure Fuel Pump external leaks from weep hole. only trucks with 2010 MaxxForce 11/13L, all N13, or A26 engines
- 10204139Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
- 10204137J1939 Data Link Troubleshooting
- 10202883New or replacement body control Module (BC,BCM) not detected; Gen 4 BCM
- 10202882How to obtain As built parameter list
Every International Transtar model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.