2013 Lexus GS
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2013 Lexus GS. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Owner complaints
19 complaints3 involved a crash1 involved a fire4 injuries
What owners report most
Latest complaints
- Unknown or other
Battery life is very short sometimes lasting no more than 9 months.
- Unknown or other
2013 Lexus GS350, VIN [XXX], manufactured 04/2013. Mileage at repair was approximately 117,310–117,485 miles. During diagnosis for check-engine/EVAP codes, liquid gasoline was found inside the EVAP canister / Leak Detection Pump assembly. This EVAP component is intended to handle fuel vapor, and…
2013 Lexus GS350, VIN [XXX], manufactured 04/2013. Mileage at repair was approximately 117,310–117,485 miles. During diagnosis for check-engine/EVAP codes, liquid gasoline was found inside the EVAP canister / Leak Detection Pump assembly. This EVAP component is intended to handle fuel vapor, and the presence of liquid fuel appears abnormal. The vehicle had multiple EVAP codes confirmed by both an independent scanner and the Lexus dealer’s Toyota TIS/Techstream system: P2401, P2402, P2419, P043E, and P043F. Park Place Lexus in [XXX] documented that the Leak Detection Pump was mechanically “stuck ON/OFF” and the Pressure Switching Valve was “stuck ON.” This appears consistent with fuel contamination or internal restriction of the EVAP canister/LDP assembly, not just a simple sensor or wiring issue. My safety concern is that liquid gasoline was present in or around an electrically actuated EVAP component located near the vehicle underbody. If fuel migrates further into the pump, connector, wiring, or surrounding area, it may create a potential fire safety risk. This component should not normally contain liquid gasoline. Park Place Lexus replaced the EVAP Emission Canister and Leak Detection Pump assembly, part #77740-30350, with 3.0 hours labor. The vehicle was dropped off XXX and ready XXX. Repair Order #1229991. After repair, the EVAP system re-test passed and the Texas emissions inspection passed. I paid $1,205.88 out of pocket; the repair was not covered by any recall or free-of-charge remedy. I have photos, videos, scan results, and the dealer repair invoice available. I am filing this complaint so NHTSA can track whether other Lexus/Toyota owners experience the same pattern of liquid fuel intrusion, mechanically stuck Leak Detection Pump / Pressure Switching Valve failure, and related EVAP codes. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Electrical system
The servo motor is bad per Lexus dealership. There is a recall for this exact problem for newer models. Years 2013 - 2016 should be included. My daughter has a 2006 Lexus, and it has the exact same problem. Lexus has a problem with their HVAC systems. The air conditioning stalls when turning on and goes from cold to warm when car is is idling.
- Steering
The contact called on behalf of the owner of a 2013 Lexus GS 350. The contact stated that while his daughter was driving at an undisclosed speed, there was an abnormal sound coming from the vehicle while making a right or left turn, and the steering wheel was moved all the way. The contact stated…
The contact called on behalf of the owner of a 2013 Lexus GS 350. The contact stated that while his daughter was driving at an undisclosed speed, there was an abnormal sound coming from the vehicle while making a right or left turn, and the steering wheel was moved all the way. The contact stated that it felt like the tires were driving over a bumpy road. In addition, the vehicle independently veered to the left while driving. No warning lights were illuminated. The vehicle was taken to an independent mechanic, who diagnosed the vehicle and determined that the steering wheel electronic control unit had failed. The vehicle was not repaired due to the cost. The contact related the failure to NHTSA Campaign Number: 12V221000 (STEERING); however, the VIN was not included. The manufacturer was not contacted. The failure mileage was approximately 71,000.
- Service brakes
Brake actuator or booster accumulator, always has been failing on Toyota/lexus hybrids, they need to do another bulletin or TSD because the malfunction is unsafe and many drivers are reporting it
- Engine
I started my car in the morning and when I started the engine it was an instant extreme rough idle with the engine light and traction control light blinking on my dashboard and the engine cuts out on its own. I have my car at a Toyota dealership since it’s closer than the Lexus dealership and they…
I started my car in the morning and when I started the engine it was an instant extreme rough idle with the engine light and traction control light blinking on my dashboard and the engine cuts out on its own. I have my car at a Toyota dealership since it’s closer than the Lexus dealership and they have ran an extensive testing diagnostic on my car resulting in a valve stuck open and a valve spring fell out. I have kept up the regular maintenance on my car, like every 5,000 miles fully synthetic oil changes, premium gas, regularly checking for recalls, always checking my fluids, correct tires and tire pressure, and I have in no way misused my car since it’s the only car I have to drive. I found that Lexus had a recall on the GS 350 for the 2007 to 2011 years for the problem I’m currently dealing with. In 2012 Lexus did not make a GS 350 but 2013 they were offered again and I feel like they didn’t resolve the engine problem before putting out the new production, at least for the 2013 year. Now as my car sits I have to pay $9,200 to fix the problem and I don’t have that type of money. I would have to sell my house to pay for my car to get fixed. Luckily the car didn’t stop running while I had my family in the car. I don’t feel that I did anything wrong to make the internal engine have a valve issue. This car should still be running at 148,100 miles.
- Steering
I own a 2013 GS350 RWD BASE MODEL. I have been having issues with the steering in this car since it was purchased in 2021 with100k miles. It seems to do great at lower speeds or on curvy roads, but when I drive on interstate going straight at around 70 to 80 mph is where it really becomes…
I own a 2013 GS350 RWD BASE MODEL. I have been having issues with the steering in this car since it was purchased in 2021 with100k miles. It seems to do great at lower speeds or on curvy roads, but when I drive on interstate going straight at around 70 to 80 mph is where it really becomes noticeable. The vehicle does not want to drive straight for anything. It does not pull in one certain direction; it is literally all over the road. I'd like to note that i have new shocks and upper shock mounts in the front, as well as tires all the way around, also replaced the sway bar linkages on the front and did an alignment. But the vehicle will veer from left to right with no rhyme or reason so bad that you cannot take your eyes off of the road to even adjust the ac or radio from fear of running into the concrete barricade or another vehicle. Something I'd like to add is that it really becomes prominent after about 10 to 15 min of interstate driving. I have taken it to two different Lexus dealerships and called Lexus directly. No one seems to know what I'm talking about; the first dealership told me to replace all of the parts that I previously mentioned. So, I did with no success. I have seen other GS owners complain about this online, so I know it is not just my car. This to me is a major safety concern because it had almost caused me to have several accidents personally not to mention it's just extremely annoying to buy a Lexus and to have to constantly pay attention and adjust the steering so as to not destroy the car and hit or hurt another driver. I always feel like I am going to get pulled over for a DUI. That is how bad it is. I own a 1999 Toyota corolla and that car is effortless to drive straight, I do not have to even think about it. I hope this in some way will help another GS owner to know that you are not alone if you experience this issue and maybe enough of us can cause Lexus to do the right thing here. THX, unhappy GS owner
- Seats · Unknown or other
Customer notice deterioration of the seat and proceeding monitoring the seat it was observed in 2021, 2023 & 2014 that while utilizing the seat heating electrical component the seat developed cracks as the heat released a burning sensation to the skin.
- Service brakes · Vehicle speed control
This was an unintended acceleration with non functional braking of a Lexus GS 350. This occured on December 18 around 8:00 AM. The driver noticed an orange triangular light in the dash while travelling slowly through a neighborhood less than a mile from the incident. While approaching a lighted…
This was an unintended acceleration with non functional braking of a Lexus GS 350. This occured on December 18 around 8:00 AM. The driver noticed an orange triangular light in the dash while travelling slowly through a neighborhood less than a mile from the incident. While approaching a lighted intersection, the car suddenly accelerated when the brake pedal was depressed. The brake pedal was stiff and did not work. The driver tried to avoid another vehicle by veering right. The car hit a curb, travelled over a small hill and ended up in a parking lot after the ensuing damage disabled the car. The driver was able to escape from the drivers door before a fire erupted on the drivers side of the engine bay. The driver's safety and any other cars or persons in the vicinity were obviously put at grave risk.
- Electrical system · Seats
clock inoperable Lumber Support Button/ Motor is inoperable. Lexus Dealership found that the cable is broken and needs to be replaced on the Driver and Passenger side. As the cable is broken it makes the driver side seat loose
- Steering
When driving at highway speeds for more than 10 minutes the steering becomes increasingly stiff until it starts locking the wheel in position. It takes quite a bit of force to get it to unlock and then whatever new position it's in it will lock that new position. It will lock in a straight line or…
When driving at highway speeds for more than 10 minutes the steering becomes increasingly stiff until it starts locking the wheel in position. It takes quite a bit of force to get it to unlock and then whatever new position it's in it will lock that new position. It will lock in a straight line or in a turn so I could let go of the wheel and it will keep turning. This leads to a potentially dangerous ping ponging back and forth until I get it to lock in a position that matches the road to stay in my lane. If I slow down to below 40mph it resets back to a normal steering feel until I speed up again. The alignment and wheel balance are both good. The suspension components are not warn out to cause a change in alignment. The car does not have lane keep assist or anything that might do that on purpose. It seems quite a few other people are having this same issue and dealerships do not seem to know what it is or how to fix it. Some people have had success with replacing the steering rack and associated control unit. No warning lamps or messages appear when this happens and the steering feels perfect at lower speeds and at higher speeds for short durations. This is only a problem when I drive on the highway for an extended period. Some people think it is heat related but it happens to me in the winter as well.
- Visibility/wiper
2013 Lexus GS 350 Stuck Wiper blades; DANGER LEVEL EXTREMELY HIGH - MAY AFFECT 2013-2015 AND 2016-2020 GS MODELS When using the wipes in either automatic mode or manual speed selection they can become stuck in the rain in the up position blocking the windshield's view. This is EXTREMELY…
2013 Lexus GS 350 Stuck Wiper blades; DANGER LEVEL EXTREMELY HIGH - MAY AFFECT 2013-2015 AND 2016-2020 GS MODELS When using the wipes in either automatic mode or manual speed selection they can become stuck in the rain in the up position blocking the windshield's view. This is EXTREMELY DANGEROUS. Deemed a MAJOR FLAW, the wiper blades can get stuck in any position while wiping. This occurs when the wiper blades are used and it is raining. This is very hard to replicate with windshield wiper fluid. To remedy the malfunction to survive in a LIFE or DEATH moment of LIMITED VISIBILITY, the driver must quickly push the wiper lever activator up and down to reset it and or pushing in the automatic rain sensing function button. Also, when stopped at a stoplight and resuming acceleration, the rain sensor does not pick up rain at low, medium, or heavy rain and does not engage the wipers. Again, the user must re-engage the wiper system by turning it on and off again multiple times while driving over and over again, multiple times during a trip. The car should not be driven on highways at high speed during when raining or above 20 MPH.
- Structure › Interior panels › Dashboard
Sticky and cracked dashboard
- Steering
Notchy steering feel at highway speed. The steering exhibit an intermittent non-binding, notchy steering feeling and/or steering wheel does not self-center condition when driving at highway speeds. Life threatening. Veers to left or right and needs quick correction.
- Fuel/propulsion system
Fuel economy became very poor. Following day had a check engine light for car running lean. Went to fill up car at gas station, and after it was filled it would not start and just crank. After 5 attempts and throttling the gas pedal the car began to sputter and finally started. Car was then parked after moving to a safe location.
- Visibility/wiper
Windshield wipers get stuck in the up position and do not work. Malfunctioning wipers, no error code with no fix. Very dangerous under extreme weather condtions where wipers are needed. Not what IS expected from a toyota product. I demand this be fixed as I've had much older cars with no issues of…
Windshield wipers get stuck in the up position and do not work. Malfunctioning wipers, no error code with no fix. Very dangerous under extreme weather condtions where wipers are needed. Not what IS expected from a toyota product. I demand this be fixed as I've had much older cars with no issues of wipers malfunction. I could crash, die or injury someone because of this failure. The car has only 41,900 miles on it and the wipers are barely used. This should not be happening! It IS not because I did something to the wipers either. I have never gone through an automatic car wash and even if I did they should be able to sustain that. This IS a lexus, where IS the perfection?
- Electrical system · Suspension
The struts are failing (leaking) and this IS a known problem across the internet. Also, the door lock actuators stop working periodically. And finally, the rear defroster stoped working. I've owned much cheaper cars with well over 100,000 miles and never experienced these problems. This car only has 82,000 and well taken care of as I have another car that I lease and the lexus IS usually in the garage.
- Air bags · Seat belts · Steering
September 27TH 2017 - 2013 lexus GS 350 for 26432 from santa monica lexus in los angeles california sold the car without the dealer revealing recalls on the car by california law it IS illegal to not disclose information on november 2ND 2018 17 he was my one airbag deployed later I found out that…
September 27TH 2017 - 2013 lexus GS 350 for 26432 from santa monica lexus in los angeles california sold the car without the dealer revealing recalls on the car by california law it IS illegal to not disclose information on november 2ND 2018 17 he was my one airbag deployed later I found out that her hair back would not even have to believe in the dealer did not disclose that at the time of purchase which IS a loofah january 1ST of 2019 I received a letter from the manufacturer telling me to return a car because of dashboard recall dealership dealership refuse to fix the dashboard send with a later on I found out that they have performed two or three set temp to fix electronic control module flash software twice from my understanding that void your warranty I turn my car in january 5TH 2019 send a receipt to return my car with they have no legal right to hold he claimed it done work on my car but they have not been in the service records to not that they didn't work on my car and I never signed any documents to give him permission to work on my car
- Air bags · Seat belts · Service brakes
Air bag or selt belt did not deploy
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11007456Some 2005 2024 Lexus vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11006162Some 2005 2024 Lexus vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11005121Some 2005 2024 Lexus vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11005063Some 2005 2024 Lexus vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11003650To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11003648The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Lexus paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. BO029-91. The entire bulletin has been updated. Service Bulletin No. BO029-91 is obsolete
- 11003643Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Lexus vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11003642Lexus vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. L-PG004-94. The entire bulletin has been updated.
- 11003641Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
- 11003595To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11003593The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Lexus paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. BO029-91. The entire bulletin has been updated. Service Bulletin No. BO029-91 is obsolete
- 11003588Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Lexus vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11003587Lexus vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. L-PG004-94. The entire bulletin has been updated.
- 11003586Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
- 10244114TSB: The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks.
- 10214355Lexus Safety Recall and Service Campaign - Technician Certification Requirements 4.13.2022
- 10209023TSB: Some 2005 ? 2022 model year Lexus vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
- 10207945POL: This consolidated Tire Warranty Guide contains the complete warranty terms for all brands of ground and spare tires currently in use by Lexus. This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Lexus.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.
- 10205383Spots in Window Glass - vehicle exterior
- 10205366Navigation/Multi Info Display Day Mode Operation - Audio/Visaul/Telematics
- 10205363Suspension - Best Practice for Tire Totation/Nitrogen Filling
- 10205361Adhesive & Sealant Cross Reference Information/ Engine Hybrid System
- 10205360Adhesive & Sealant Cross Reference Information/ Engine Hybrid System
- 10205359Oil Viscosity Applicability and Cfhange Interval Guide
- 10205358Oil Viscosity Applicability and Cfhange Interval Guide
- 10205352Windshield Wiper Blade Maintenance and cleaning
- 10205346Auto matic Transmission Replacement kPrecautions
- 10205331Immobilizer and Smart Key Reset
- 10190468Lexus Safety Recall and Service Campaign - Technician Certification Requirements
- 10179782Ti: technical instructions for limited service campaign klg customer support program 19le05 safety connect system ? Vehicle location inaccurate
- 10179738Ti: technical instructions for limited service campaign klg customer support program 19le05 safety connect system ? Vehicle location inaccurate
- 10179697TSB: Vehicles may display evidence of a fluid leak or fluid seep from powertrain components. This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address this condition.
- 10179601TSB: Vehicles may display evidence of a fluid leak or fluid seep from powertrain components. This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address this condition.
- 10177780TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. ST004-01, SU001-08, and L-SB-0174-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Lexus vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.
- 10176283Safety Recall and Service Campaign - Technician Certification Requirements
- 10174889TSB: OBSOLETE NOTICE April 06, 2020: This bulletin is now obsolete. Please see L-SB-0008-20. Replacement Certification Labels and VIN Plates
- 10174888TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. L-SB-0048-08, PG007-07, PG016-01, PG015-01, PG004-97, PG003-97, PG003-93, PG002-90, L-SB-0048-08, PG007-07, PG016-01, PG015-01, PG004-97, PG003-97, PG003 93, and PG002-90. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1990 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin.
- 10172827TSB: February 06, 2020: This bulletin is now obsolete. Please see L-SB-0003-20.
- 10172821The Data Communication Module (DCM) in the subject vehicles is equipped with software to identify the location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated
- 10168534Technical instructions: technical instructions for limited service campaign klg customer support program 19le05 safety connect system ? Vehicle location inaccurate certain 2011 ? 2017 model year LS, 2013 ? 2016 model year LS hybrid, 2011 ? 2017 model year GS, 2016 ? 2017 model year gs-f, 2013 ? 2017 model year GS hybrid, 2010 ? 2017 model year IS, 2011 ? 2015 model year is-c, 2013 ? 2014 model year is-f, 2015 ? 2017 model year RC, 2015 ? 2017 model year rc-f, 2011 ? 2017 model year ct, 2010 ? 2017 model year RX, 2010 ? 2017 model year RX hybrid, 2015 ? 2017 model year NX, 2015 ? 2017 model year NX hybrid, 2010 ? 2017 model year LX, 2010 ? 2018 model year GX, 2010 ? 2017 model year ES, 2013 ? 2017 model year ES hybrid updated 10/17/2019
Every Lexus GS model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.