2013 Mazda CX-5
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mazda › CX-5 › 2013
These records cover every 2013 Mazda CX-5. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
1 recall names the 2013 Mazda CX-5. Newest first.
Mazda North American Operations (Mazda) is recalling certain model year 2010-2013 Mazda3 and Mazdaspeed3 vehicles manufactured November 18, 2008, to June 8, 2013, 2012-2015 Mazda5 vehicles manufactured October 26, 2010, to June 22, 2015, 2016 CX-3 vehicles manufactured June 1, 2015, to December 26, 2015, and 2013-2016 CX-5 vehicles manufactured December 15…
Risk and remedy
Risk
If the lift gate falls unexpectedly, it may hit the user, increasing their risk of injury.
Remedy
Mazda dealers will replace the both lift gate supports, free of charge, however parts are not currently available. The recall began April 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9916H.
Owner complaints
194 complaints6 involved a crash1 involved a fire8 injuries
What owners report most
Latest complaints
- Unknown or other
Shifter switch has gone out and no longer recognizes the car is in park, causes battery drainage because car cannot fully turn off. Car not recognizing gears can cause car accidents and possible loss of life. This issue can be found online as a known defect in mazda cx-5 that has not been recalled.…
Shifter switch has gone out and no longer recognizes the car is in park, causes battery drainage because car cannot fully turn off. Car not recognizing gears can cause car accidents and possible loss of life. This issue can be found online as a known defect in mazda cx-5 that has not been recalled. Vehicle has been inspected and issue has been verified.There were no warning lights, sounds or symptoms of potential failure before failure. Mazda has had recalls and service bulletins related to shifter/ignition switches, particularly for models like the CX-5 and MX-5 (Miata) in years like 2013-2019, concerning worn shifter switch units (Part #KDY0-46-040) that can prevent the ignition from fully turning off in Park, potentially draining the battery or causing accidental activation. While some were major recalls (like the 1.4 million vehicle ignition switch issue in 2015), many were Technical Service Bulletins (TSBs) for the shifter switch issue where owners sometimes got repairs free even outside warranty due to the commonality.
- Unknown or other
Shifter switch has gone out and no longer recognizes the car is in park, causes battery drainage because car cannot fully turn off. Car not recognizing gears can cause car accidents and possible loss of life. This issue can be found online as a known defect in mazda cx-5 that has not been recalled.…
Shifter switch has gone out and no longer recognizes the car is in park, causes battery drainage because car cannot fully turn off. Car not recognizing gears can cause car accidents and possible loss of life. This issue can be found online as a known defect in mazda cx-5 that has not been recalled. Vehicle has been inspected and issue has been verified.There were no warning lights, sounds or symptoms of potential failure before failure. Mazda has had recalls and service bulletins related to shifter/ignition switches, particularly for models like the CX-5 and MX-5 (Miata) in years like 2013-2019, concerning worn shifter switch units (Part #KDY0-46-040) that can prevent the ignition from fully turning off in Park, potentially draining the battery or causing accidental activation. While some were major recalls (like the 1.4 million vehicle ignition switch issue in 2015), many were Technical Service Bulletins (TSBs) for the shifter switch issue where owners sometimes got repairs free even outside warranty due to the commonality.
- Unknown or other
Shifter switch has gone out and no longer recognizes the car is in park, causes battery drainage because car cannot fully turn off. Car not recognizing gears can cause car accidents and possible loss of life. This issue can be found online as a known defect in mazda cx-5 that has not been recalled.…
Shifter switch has gone out and no longer recognizes the car is in park, causes battery drainage because car cannot fully turn off. Car not recognizing gears can cause car accidents and possible loss of life. This issue can be found online as a known defect in mazda cx-5 that has not been recalled. Vehicle has been inspected and issue has been verified.There were no warning lights, sounds or symptoms of potential failure before failure. Mazda has had recalls and service bulletins related to shifter/ignition switches, particularly for models like the CX-5 and MX-5 (Miata) in years like 2013-2019, concerning worn shifter switch units (Part #KDY0-46-040) that can prevent the ignition from fully turning off in Park, potentially draining the battery or causing accidental activation. While some were major recalls (like the 1.4 million vehicle ignition switch issue in 2015), many were Technical Service Bulletins (TSBs) for the shifter switch issue where owners sometimes got repairs free even outside warranty due to the commonality.
- Unknown or other
Shifter switch has gone out and no longer recognizes the car is in park, causes battery drainage because car cannot fully turn off. Car not recognizing gears can cause car accidents and possible loss of life. This issue can be found online as a known defect in mazda cx-5 that has not been recalled.…
Shifter switch has gone out and no longer recognizes the car is in park, causes battery drainage because car cannot fully turn off. Car not recognizing gears can cause car accidents and possible loss of life. This issue can be found online as a known defect in mazda cx-5 that has not been recalled. Vehicle has been inspected and issue has been verified.There were no warning lights, sounds or symptoms of potential failure before failure. Mazda has had recalls and service bulletins related to shifter/ignition switches, particularly for models like the CX-5 and MX-5 (Miata) in years like 2013-2019, concerning worn shifter switch units (Part #KDY0-46-040) that can prevent the ignition from fully turning off in Park, potentially draining the battery or causing accidental activation. While some were major recalls (like the 1.4 million vehicle ignition switch issue in 2015), many were Technical Service Bulletins (TSBs) for the shifter switch issue where owners sometimes got repairs free even outside warranty due to the commonality.
- Unknown or other
Shifter switch has gone out and no longer recognizes the car is in park, causes battery drainage because car cannot fully turn off. Car not recognizing gears can cause car accidents and possible loss of life. This issue can be found online as a known defect in mazda cx-5 that has not been recalled.…
Shifter switch has gone out and no longer recognizes the car is in park, causes battery drainage because car cannot fully turn off. Car not recognizing gears can cause car accidents and possible loss of life. This issue can be found online as a known defect in mazda cx-5 that has not been recalled. Vehicle has been inspected and issue has been verified.There were no warning lights, sounds or symptoms of potential failure before failure.
- Unknown or other
The lower control arm or axel on the front passenger side broke as I was backing out of a parking spot. It is still at the mechanic however that is what is required to put the wheel back on the vehicle. My understanding is that this is the second time I have had this problem with the lower control…
The lower control arm or axel on the front passenger side broke as I was backing out of a parking spot. It is still at the mechanic however that is what is required to put the wheel back on the vehicle. My understanding is that this is the second time I have had this problem with the lower control arm on this vehicle. That could be very dangerous if that happens while on the highway and I’m concerned there is a fundamental problem with this car if it has happened twice. The first time the car was only a few years old. It was around 2016 if I recall correctly and Mazda fixed it.
- Unknown or other
The display on my rearview camera is extremely foggy. It appears to have had a breach where water has leaked into the camera itself. I have cleaned the lens but yo no avail. I never had a clear screen, and at times it is so bad that I can’t see anything at all. In fact, I have already backed into…
The display on my rearview camera is extremely foggy. It appears to have had a breach where water has leaked into the camera itself. I have cleaned the lens but yo no avail. I never had a clear screen, and at times it is so bad that I can’t see anything at all. In fact, I have already backed into the corner of a building in a parking lot due to lack of visibility. I can’t tell you the number of times I’ve attempted to back out and almost hit a pedestrian or another car driving behind me that I couldn’t see well. It’s a good thing I use my mirrors and rear window, or that could have easily happened. I wonder if the work that was done on my rear hatch from a previous recall may have caused the seal protecting the camera unit to be compromised. There have been a number of recalls recently from other manufacturer’s, so I believe this is a common issue that should be addressed in my case as well.
- Vehicle speed control
When in the highway and changing lanes and you try to excelerate it doesnt take off ..instead just acts as if i had over excelerated but not speeding up.. i have almost been ran over because i could not get enough speed to switch lanes.
- Seats
I recently purchased this used vehicle. Right away, I noticed that when I used the recline lever, it didn't stop when removing my hand from it. I had to push the lever back to the middle position to stop it. I thought this was annoying, but didn't think much of it. On Thursday [XXX] I stopped at a…
I recently purchased this used vehicle. Right away, I noticed that when I used the recline lever, it didn't stop when removing my hand from it. I had to push the lever back to the middle position to stop it. I thought this was annoying, but didn't think much of it. On Thursday [XXX] I stopped at a gas station, went inside, and when I came back out the seat was fully reclined. It was so far back that it was lodged in the car seat behind the drivers seat. I tried to move the back up but it wouldn't come back up. The seat would move forward and back, but the recline level didn't work. I drove to my next destination with the seat all the way back. Then I turned the car off and on several times before it would go back up. I then picked up my kids, went to the grocery store and came back home. I turned the car off and went to the way back to get my groceries out, while my kids were still unbuckling. As I was in the back I heard them both start screaming. I ran back around and the drivers side seat was leaned at the way back, with my 6 year old trapped and the headrest part crushing her throat and chest. Thankfully, I was able to move it back up. If it hadn't worked to move up, like just a few hours previously, I don't know what I would have done but it would have been horrible. My daughter was screaming and crying and in a lot of pain. Her throat and chest were red and scratched. It appears that when I get out of the car my leg may slightly touch the recline button, and then it doesn't stop moving. This is incredibly dangerous. I looked it up online and found a couple other reports about it, including one about a baby trapped in a car seat. I can't believe there wasn't a recall. I took it to the dealer I bought it from, and it did continue to do the same thing. They are looking into ordering a new part. In the meantime it is unplugged underneath the seat, so it can't move. That brings on a dash light with the airbags, so I'm not sure if it means my airbag won't work. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF
- Unknown or other
Turn the car off--but it does not turn off. I've had my battery run down so many times. The problem is a sensor in the gear shifter that is not telling the vehicle it’s in park. This is a huge reoccurring safety issue.
- Electrical system
The car does not turn off when I put it in park and push the ON/OFF button. I have to start and turn off multiple times and jiggle the gear shift multiple times before it turns off. Sometimes even that doesn't work. Because the car doesn't completely turn off, it runs the battery down which leaves…
The car does not turn off when I put it in park and push the ON/OFF button. I have to start and turn off multiple times and jiggle the gear shift multiple times before it turns off. Sometimes even that doesn't work. Because the car doesn't completely turn off, it runs the battery down which leaves me dangerously stranded. The car is available for inspection. My safety is put at risk because it drains the battery and leaves me stranded, sometimes in dangerous situations unable to get assistance. I have not taken it to a dealer or service center but have seen MULTIPLE reports of other owners of this same vehicle having the same problem. The problem has not been inspected by the manufacturer, police, insurance representatives or others. There were no warning lamps, messages, or other symptoms before the problems started. It started a while ago but I'm not certain of the date. The messages I've read online of it happening to others are from several years ago, so this seems to be a problem that has been ongoing for several years that Mazda has failed to address.
- Unknown or other
While driving, 30 mph on Dempster Street in Niles, Illinois, the sunroof spontaneously exploded and shattered.
- Steering
Ball joint broke gave out while turning
- Engine
The car battery will not turn off when I turn off the vehicle.
- Electrical system
My car does not turn off when you push the ignition button. I spoke to Mazda's parts manager about this, and his wife had the same issue and the same model and year as my car. He told me that it is the Parking Lever switch. I feel that not being able to turn your car off is a safety issue. I filed a safety issue with my 2013 Mazda CX-5 on May 26, 2022.
- Electrical system
When you shut the car off the radio and other components do not shut down. You have to start the car back up and put in gear then back in park and shut the car off (sometimes two or three times) to get everything to shut down. This is getting worse over time.
- Electrical system · Engine
My car won't shut off! I put it in park and turn it off and the accessories stay on. It is getting worse and worse and has taken up to 7 times of turning it off and on, backing it up and forward before it will just turn off for me. I get scared that it won't turn off. I found this forum online and…
My car won't shut off! I put it in park and turn it off and the accessories stay on. It is getting worse and worse and has taken up to 7 times of turning it off and on, backing it up and forward before it will just turn off for me. I get scared that it won't turn off. I found this forum online and it seems this is a very common problem that is not being addressed by Mazda. https://www.cargurus.com/Cars/Discussion-t49115_ds799849 Not being able to turn my car off is a very big safety risk for me and my 2 year old son.
- Electrical system
The contact owns a 2013 Mazda CX-5. The contact stated that the PUSH to START button was not able to turn off the vehicle until after several attempts were made, which caused the battery to drain quickly. The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The…
The contact owns a 2013 Mazda CX-5. The contact stated that the PUSH to START button was not able to turn off the vehicle until after several attempts were made, which caused the battery to drain quickly. The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure, and the contact was waiting for a callback. The failure mileage was approximately 100,000.
- Power train › Automatic transmission › Park/neutral start interlock switch
The contact owns a 2013 Mazda CX-5. The contact stated while shifting into the park the electronics failed to turn off. The contact vigorously shifted the gear shifter in several positions for approximately 10 to 15 minutes to turn off electronics. There were no warning indicator lights…
The contact owns a 2013 Mazda CX-5. The contact stated while shifting into the park the electronics failed to turn off. The contact vigorously shifted the gear shifter in several positions for approximately 10 to 15 minutes to turn off electronics. There were no warning indicator lights illuminated. The contact was concerned about the battery being drained. The vehicle was taken to the local dealer where the contact was informed that the vehicle was not covered under the recall. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was unknown.
- Electrical system · Power train
My vehicle does not want to turn off when placed in park. The car is fully in the park position, but the start push button is illuminated with a red light. The power is still on, and the car beeps when door is open. I can only get the power to turn off, after repeatedly tapping the gear shift left…
My vehicle does not want to turn off when placed in park. The car is fully in the park position, but the start push button is illuminated with a red light. The power is still on, and the car beeps when door is open. I can only get the power to turn off, after repeatedly tapping the gear shift left, towards the P symbol. It is already fully seated in the park position, but this finally causes the light to go off and the car turns off. Always hoping the power did not turn back on while away from the car. Is this a fire hazard? I will not park my car in the garage as I am concerned it may overheat the wiring, electrical components, etc...??? I have noticed similar complaints for this vehicle on this website also.
- Suspension
On Saturday afternoon 7/24 I was leaving a parking lot when my drivers side wheel detached from my front axle rod. I have around 90k miles on the vehicle. There was no indication of a part coming loose. Never noticed vibration of wheel or any resistance during movements. This should be a recall on the vehicle.
- Electrical system · Power train
The contact owns a 2013 MAZDA CX5. The contact stated while attempting to shut off the vehicle, the vehicle failed to turn off due to the transmission not being fully in PARK. The contact stated that there was an unknown flashing red warning light illuminated. The vehicle was not yet diagnosed. The…
The contact owns a 2013 MAZDA CX5. The contact stated while attempting to shut off the vehicle, the vehicle failed to turn off due to the transmission not being fully in PARK. The contact stated that there was an unknown flashing red warning light illuminated. The vehicle was not yet diagnosed. The manufacturer was informed of the failure and the contact was awaiting a response. The failure mileage was approximately 100,000.
- Electrical system · Engine · Fuel/propulsion system
After fixing the electrical problem with the car not fully turning off, the car suddenly died in traffic and wouldn't restart. Replacing mass air sensor, O2 sensor, and plugs, the car will die in traffic when coming to a stop, but restarts immediately. The code says this IS a pcm problem. Internet research says this IS not uncommon resulting in safety recalls in other year models. 2013 should also be recalled.
- Electrical system · Engine
The ignition on my 2013 mazda CX-5 would not turn off after putting the vehicle into park. The engine would start with the gearshift lever in park, but once I drove to a destination, pulled into a parking lot, and put the gearshift into park, the vehicle would not entirely turn off. It would take…
The ignition on my 2013 mazda CX-5 would not turn off after putting the vehicle into park. The engine would start with the gearshift lever in park, but once I drove to a destination, pulled into a parking lot, and put the gearshift into park, the vehicle would not entirely turn off. It would take several attempts to manipulate the gearshift around to get the car to turn off. The vehicle's electrical system would still be active, including radio, dash lights, headlights, and other electrical systems would all remain on. After contacting a local mazda dealership in town, a "park safety switch" in the gearshift lever IS being affected, and it IS a known problem affecting mazda CX-5 vehicles. However, there have not been any recalls issued for this problem. Thanks to a quick google search such as "mazda CX-5 will not turn off", I found out about this issue. There are several youtube videos, posts on reddit and mazda forums discussing this issue. Having a vehicle with an issue where you cannot turn the car off because the car "thinks" that the vehicle IS not in park IS unsafe and a safety hazard and can cause an accident or worse.
- Engine · Fuel/propulsion system · Vehicle speed control
While driving my vehicle on the interstate the car lost the ability to accelerate. All of the dashboard lights came on and I had to coast to the side of the interstate. After restarting the vehicle I was able to drive it but I cannot take the vehicle over 30 mph now without it shuttering and having…
While driving my vehicle on the interstate the car lost the ability to accelerate. All of the dashboard lights came on and I had to coast to the side of the interstate. After restarting the vehicle I was able to drive it but I cannot take the vehicle over 30 mph now without it shuttering and having acceleration issues. This IS a serious and life threatening issue that needs to be fixed free of charge. I have found other reports of this happening but I see no recall information. This needs to be fixed before mazda has lawsuits filed against them. This IS a manufacturing error and not a usage error. Please look into this.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11011141Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
- 11009654The SKYACTIV-DRIVE FW6A-EL AT uses Automatic Transmission Fluid (ATF) Type: FZ. Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
- 11009644Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11008577Some customers may complain about scratches on the instrument cluster lens.
- 11007029For improvement of electrical diagnosis, the SKYACTIV Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
- 11007022Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 11007019If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 11007018Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
- 11007013Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
- 11007010Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
- 11007009Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11006987In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
- 11006917Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
- 11005671Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 11005528Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plates surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.
- 11003398Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 11003397Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 11003396Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 10254191Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 10252508Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 10251387Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 10244679If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 10244671Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
- 10243569Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 10243568Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 10243545Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plates surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.
- 10241637Some customers may complain about scratches on the instrument cluster lens.
- 10240496Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 10238697Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. NOTE: The antistatic effect does not deteriorate with this procedure.
- 10238695Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
- 10238663Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.
- 10237216If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 10237215Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 10237199Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738).
- 10235414Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
- 10233704Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.
- 10233669There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method
- 10232304Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.
- 10232299Speedometer replacement procedure
- 10232277Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
Every Mazda CX-5 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.