2014 Mazda CX-5
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mazda › CX-5 › 2014
These records cover every 2014 Mazda CX-5. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2014 Mazda CX-5. Newest first.
Mazda North American Operations (Mazda) is recalling certain model year 2010-2013 Mazda3 and Mazdaspeed3 vehicles manufactured November 18, 2008, to June 8, 2013, 2012-2015 Mazda5 vehicles manufactured October 26, 2010, to June 22, 2015, 2016 CX-3 vehicles manufactured June 1, 2015, to December 26, 2015, and 2013-2016 CX-5 vehicles manufactured December 15…
Risk and remedy
Risk
If the lift gate falls unexpectedly, it may hit the user, increasing their risk of injury.
Remedy
Mazda dealers will replace the both lift gate supports, free of charge, however parts are not currently available. The recall began April 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9916H.
Mazda North American Operations (Mazda) is recalling certain model year 2016 CX-3 vehicles manufactured June 1, 2015, to December 2, 2015, 2013-2014 Mazda2 vehicles manufactured July 3, 2013, to August 8, 2014, 2014-2016 CX-5 vehicles manufactured January 19, 2013, to December 2, 2015, and 2013-2015 CX-9 vehicles manufactured December 6, 2012, to July 31…
Risk and remedy
Risk
If the steering knuckle separates from the strut assembly, it can cause a loss of steering control, increasing the risk of a crash.
Remedy
Mazda will notify owners, and dealers will inspect the lower mounting nuts and bolts that secure the front strut assembly to the steering knuckle. If the bolts are loose, they will be replaced and then correctly tightened, free of charge. The recall is expected to begin May 20, 2016. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9316D.
Mazda North American Operations (Mazda) is recalling certain model year 2014-2016 Mazda CX-5 vehicles manufactured June 27, 2013, to February 2, 2016. The affected vehicles have a fuel filler pipe that may rupture in the event of a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number…
Risk and remedy
Risk
A rupture of the fuel filler pipe may result in a fuel leak, increasing the risk of a fire.
Remedy
Mazda will notify owners, and dealers will alter the attachment between the fuel filler pipe and the left rear side of the bracket of the fuel filler pipe, free of charge. The recall began on February 25, 2016. Owners may contact Mazda customer service at 1-800-222-5500, option 6. Mazda's number for this recall is 9216B.
Pilkington North America, Inc. (Pilkington) is recalling certain replacement windshields, model FW04026 GTY, manufactured November 23, 2015, to December 16, 2015 for use in Mazda CX-5 vehicles that are equipped with the Smart City Brake Support system. The affected windshields have a bracket mounted on the inside to hold a laser sensor or LIDAR device for…
Risk and remedy
Risk
If the bracket loosens or detaches from the windshield, the safety features of the Smart City Brake Support system may be disabled and therefore increase the risk of a crash.
Remedy
Pilkington will contact the wholesalers and retailers that purchased the windshields to try to identify the affected customers. The affected windshields will be replaced, free of charge. This recall began on February 15, 2016. Owners may contact Pilkington at 1-844-278-7230.
Owner complaints
377 complaints7 involved a crash6 injuries
What owners report most
Latest complaints
- Electrical system
The car's electrical system doesn't fully turn off after being put in park and turning the ignition off. The electrical system stays on, despite the engine and ignition turned off. It's a BIG problem that I've seen a lot of other people report. And yet Mazda refuses to address the issue.
- Air bags
I was driving down the road and my right side curtain airbag deployed. I did let my insurance company know but was told that they couldn’t do anything for me since it was not an accident. I called the local Mazda dealership and they told me that they could inspect the vehicle but it would not be on…
I was driving down the road and my right side curtain airbag deployed. I did let my insurance company know but was told that they couldn’t do anything for me since it was not an accident. I called the local Mazda dealership and they told me that they could inspect the vehicle but it would not be on them. That it could have been a rat that chewed on something to cause it to deploy because I was not the first owner of the vehicle. There was no other damage other than the airbag and where it came through on the side.
- Steering
The contact owns a 2014 Mazda CX-5. The contact stated that while her husband was driving at a slow speed and attempting to parallel park, there was an abnormal sound coming from the engine before the steering wheel seized. No warning light was illuminated. The contact's husband exited the vehicle…
The contact owns a 2014 Mazda CX-5. The contact stated that while her husband was driving at a slow speed and attempting to parallel park, there was an abnormal sound coming from the engine before the steering wheel seized. No warning light was illuminated. The contact's husband exited the vehicle to inspect the vehicle, and another person stopped to assist and became aware that the ball joint had detached. The vehicle was towed to an independent mechanic, where it was diagnosed and determined that the steering knuckle had separated from the strut assembly, causing the failure. The vehicle was not repaired. The dealer was contacted and stated that the vehicle was not under warranty. The manufacturer was notified of the failure, but no assistance was provided. The contact related the failure to NHTSA Campaign Number: 16V203000 (STEERING); however, the VIN was not included. The failure mileage was approximately 135,000.
- Electrical system › Instrument panel › Speedometer/odometer
Odometer Fraud. The contact purchased a 2014 Mazda CX-5. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 86,000, and at the time of registration, it was discovered that the mileage was 190,000.
- Unknown or other
Car accessories will not shut off when I put vehicle in park. this IS dangerous due to causing the battery to completely drain leaving me stranded.
- Electrical system · Unknown or other
Auxiliary power will not turn off when vehicle is turned off. Radio , lights interior power , etc….. car turns off when button is pressed but interior power does not .
- Engine · Power train · Service brakes
I was waiting at a traffic signal to make a left turn, with my foot on the brake. The car accelerated aggressively, with no warning, like the pedal was pushed to the floor. I stood on the brake and shoved the shifter into park - coming to a stop in the middle of the intersection, Fortunately my…
I was waiting at a traffic signal to make a left turn, with my foot on the brake. The car accelerated aggressively, with no warning, like the pedal was pushed to the floor. I stood on the brake and shoved the shifter into park - coming to a stop in the middle of the intersection, Fortunately my wheels were pointed straight and the car did not race into oncoming traffic. My [XXX] father was in the car with me. Thankfully, my grandchildren were NOT in the car. You could smell the gas and brakes. It was NOT driver foot placement, nor was it floor mats. Vehicle has ~ 75K miles, and I am terrified of this happening again. I had driven this car regularly in rush hour stop & go traffic for years with no event like this ever before. Apparently sudden unintended vehicle acceleration is a recognized problem. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Electrical system
Car fails to shut off completely. The motor stops, but the electronics (dash, radio, etc.) and things like the A/C still are on. Searching forums shows it is a faulty gear shift sensor that detects that the car is in park.
- Fuel/propulsion system · Visibility/wiper
There is a pressure crack that goes almost all the way across my front windshield, there are no chips or dings in the glass. Second you can smell gas fumes near the back of the car but no gas is leaking
- Electrical system · Engine
The contact owns a 2014 Mazda CX-5. The contact stated that while attempting to turn off the vehicle, the vehicle failed to shutoff. The screen and vehicle remained powered on. The battery was drained, and the contact replaced the battery. The contact called the local dealer, but the vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 77,000.
- Engine
The contact owns a 2014 Mazda CX-5. The contact stated that while driving at 35 MPH, the check engine warning light illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the heater core. The contact was informed that the heater core needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 57,311.
- Unknown or other
In the past year the car has consistently given a “Set to P” message when parked and already shifted to Park, and doesn’t completely turn off (though the engine does). We have to turn the car back on, jam the car to P and try again. Internet tells me this was recalled for 2013-2014 cx-5s just before vehicles starting with the same VIN info as mine.
- Electrical system
We have had numerous times that the vehicle ignition system will not turn off after pushing the stop button. The motor will stop but the ignition and radio system stay on. The car must be restarted(sometimes numerous times) and shut down before the ignition system shuts down. I have seen many other owner's complaints about this same problem on (carcomplaints .com).
- Electrical system
The contact owns a 2014 Mazda CX-5. The contact stated that when he turned off the vehicle, the radio remained operational. The contact disconnected and reconnected the battery. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 191,493.
- Unknown or other
UNKNOWN - A few months ago, I started to have an issue when turning off the vehicle. After putting the vehicle in park and pressed to turn off the vehicle, the radio/GPS screen would stay on and a warning message stating the car must be in ‘P’ark. I would restart the car, put it in neutral, turned…
UNKNOWN - A few months ago, I started to have an issue when turning off the vehicle. After putting the vehicle in park and pressed to turn off the vehicle, the radio/GPS screen would stay on and a warning message stating the car must be in ‘P’ark. I would restart the car, put it in neutral, turned it off, but the same message kept popping up and would beep at me when trying to close the door. I jiggle the stick multiple times and tried different ways to turn off the car, now taking as many as 10 times before the radio/GPS screen turns off and the message goes away. I made an appt with the closest dealer, but I have to wait for 4 weeks for the car to be inspected & corrected. This seem like a safety hazard not knowing if the car is actually in park and turned off so the battery doesn’t drain. There should be a recall issued by Mazda to correct this issue as many people have posted the same problem over many years.
- Unknown or other
When the vehicle is put in park and the button is pressed to turn off the vehicle, the radio display screen stays on. I have to recrank the car, put it in a different gear, and then back into park and try again. Sometimes I do this process up to 10 times in order for the display screen to turn off. When the display screen stays on, the battery is drained within hours.
- Unknown or other
A couple of months ago we started to have an issue when trying to turn off our vehicle. A warning message stating the car must be be in 'P' to turn off keeps popping up even though the shift stick is in the correct position. We have to jiggle the stick multiple times before the car turns off. This…
A couple of months ago we started to have an issue when trying to turn off our vehicle. A warning message stating the car must be be in 'P' to turn off keeps popping up even though the shift stick is in the correct position. We have to jiggle the stick multiple times before the car turns off. This can be a safety hazard if the car is in fact not safely in the park position after being able to turn off the car. The vehicle was recently serviced for an oil change and we were reminded of the issue and were told this is a known issue. They recommended to change the shift switch to resolve it.
- Electrical system · Power train
The contact owns a 2014 Mazda CX-5. The contact stated while attempting to turn off the vehicle, the vehicle failed to immediately turn off. After several attempts, the contact was able to turn off the vehicle. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was 70,000.
- Unknown or other
2014 Mazda CX5 will not turn off, keeps telling me to put it in park - then it tells me key fob battery low, which it is not. I have to turn the car on/off, on/off, on/off to get it to shut off.
- Engine
Vehicle was at highway speed when the warning light for high engine coolant temperature came on with a warning message to stop the vehicle in a safe place. The engine stopped and I was almost hit by a semi-truck as I was struggling to move over a lane to stop on the side of the highway. Vehicle…
Vehicle was at highway speed when the warning light for high engine coolant temperature came on with a warning message to stop the vehicle in a safe place. The engine stopped and I was almost hit by a semi-truck as I was struggling to move over a lane to stop on the side of the highway. Vehicle was towed to the auto shop and diagnosed with a crack in the cylinder head. There was no problems prior to this. My research has shown that this has become a common problem with this vehicle.
- Engine
The engine will not turn off when pressing the start/stop button while the transmission shifter is in park.
- Engine
The electrical component of the car does not turn off when the vehicle is in park and the push button disengaged. Drains battery and leaves me stranded. Can’t lock doors to prevent unwanted entry once this happens as everything is battery powered.
- Steering · Suspension
Car was inspected in April of 2021. The front of car started making knocking or clunking sounds on the right side. 2 weeks later, while making a U-turn instead of getting on the interstate, there was a loud crunch/crash sound. It sounded like a garbage can went under the vehicle. Upon further…
Car was inspected in April of 2021. The front of car started making knocking or clunking sounds on the right side. 2 weeks later, while making a U-turn instead of getting on the interstate, there was a loud crunch/crash sound. It sounded like a garbage can went under the vehicle. Upon further investigation, realized that the right ball joint somehow dropped out of the knuckle. This forced the axle to pop out and further damaged the rest of the suspension components. Thank god this didn’t happen on the highway with my wife and 2 toddlers in the car- that would have been horrific.
- Steering
The contact owns a 2014 Mazda CX-5. The contact stated while driving over a speed bump the front-end of the vehicle collapsed to the ground. There was no warning light illuminated. The vehicle was towed to an independent mechanic, and the front strut assembly was replaced; however, the failure…
The contact owns a 2014 Mazda CX-5. The contact stated while driving over a speed bump the front-end of the vehicle collapsed to the ground. There was no warning light illuminated. The vehicle was towed to an independent mechanic, and the front strut assembly was replaced; however, the failure reoccurred. The vehicle was taken to the independent mechanic and the front strut assembly was replaced again. The dealer was contacted and stated that the vehicle was not under warranty. The manufacturer was not contacted. The failure mileage was 146,000.
- Unknown or other
The car wouldn’t fully turn off once it parks. Have to keep playing turn on/off game until it fully turn off. And apparently Mazda know about the issue but refuse to do anything. Other people are saying it’s a engine sensor issue.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11011141Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
- 11009654The SKYACTIV-DRIVE FW6A-EL AT uses Automatic Transmission Fluid (ATF) Type: FZ. Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
- 11009644Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11008577Some customers may complain about scratches on the instrument cluster lens.
- 11007029For improvement of electrical diagnosis, the SKYACTIV Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
- 11007022Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 11007019If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 11007018Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
- 11007013Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
- 11007010Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
- 11007009Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11006987In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
- 11006917Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
- 11005671Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 11005528Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plates surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.
- 11003398Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 11003397Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 11003396Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 10254191Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 10252508Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 10251387Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 10244679If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 10244671Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
- 10243569Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 10243568Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 10243545Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plates surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.
- 10241637Some customers may complain about scratches on the instrument cluster lens.
- 10240496Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 10238697Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. NOTE: The antistatic effect does not deteriorate with this procedure.
- 10238695Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
- 10238663Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.
- 10237216If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 10237215Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 10237199Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738).
- 10235414Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
- 10233704Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.
- 10233669There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method
- 10232304Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.
- 10232299Speedometer replacement procedure
- 10232277Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
Every Mazda CX-5 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.