2009 Mazda MAZDASPEED3

Recalls

1 recall names the 2009 Mazda MAZDASPEED3. Newest first.

• Visibility › Windshield wiper/washer › Motor

  Jun 15, 2011NHTSA 11V329000103,300 vehicles

  Mazda IS recalling certain model year 2008-2009 mazda3 and mazdaspeed3 vehicles manufactured from january 7, 2008, through november 28, 2008. the ground terminal of the windshield wiper motor may have been inadvertently bent during assembly. if this condition exists then over time the electrical resistance of the motor circuit may increase up to a point…

  Risk and remedy

  Risk

  The loss of wiper function in adverse weather could potentially increase the risk of a crash.

  Remedy

  Dealers will install an additional ground harness on the wiper motor free of charge. the safety recall IS expected to begin on or before july 15, 2011. owners may contact mazda customer assistance center at 1-800-222-5500.

  Full recall details →

Owner complaints

What owners report most

1. Engine1
2. Power train1
3. Seats1
4. Tires1
5. Wheels1

Latest complaints

• Apr 30, 2016WI4,000 mi
  Wheels

  Something IS wrong with the design of the car...after around 4, 000 miles I needed new tires because they were wearing unevenly. with every new replacement I've gotten, they definitely have worn before they should have worn out...tire people say they are wearing unevenly and they see this with mazdas.

• Dec 28, 2015NC110,960 mi
  Engine · Power train

  I was driving on the interstate and my engine shut off abruptly. I checked the engine and found a hole in the engine block. Oil trails out of the hole in the engine block. Smoke came out of the engine bay.

• Oct 18, 2012OH45,000 mi
  Seats

  The driver seat rail has become loose within its internal structure causing the entire seat assembly to rock back and forth during acceleration, braking, shifting, and cornering. The issue has become more severe over the past ten thousand miles, to the point where its motion IS noticeable even to passengers. *tr

• May 31, 2011NJ37,000 mi
  Tires › Valve
  TL* the contact owns a 2009 mazada speed3. The contact was driving approximately 65 mph when the tire pressure monitoring light illuminated on the instrument panel. The vehicle was pulled over and the contact noticed the front passenger side tire was completely flat. The contact also stated that…

  TL* the contact owns a 2009 mazada speed3. The contact was driving approximately 65 mph when the tire pressure monitoring light illuminated on the instrument panel. The vehicle was pulled over and the contact noticed the front passenger side tire was completely flat. The contact also stated that the valve stem was pushed inside of the tire. A spare tire was installed on the vehicle. The failure recurred on the front driver side tire. The vehicle was taken to an independent repair shop where the contact was informed the valve stems on all four tires were corroding and needed to be replaced. The vehicle was in the process of being repaired. The failure mileage was 37,000.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11006987In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
• 10232299Speedometer replacement procedure
• 10213430Excessive condensation or water within the headlamp assembly caustion
• 10213427HandsFree bluetooth module and/or text messaging troubleshooting procedure
• 10213330PreMixed long life "FL22" Engine Coolant
• 10200527This service bulletin provides information regarding the proper use of the drivers floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage.
• 10188016This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
• 10188015The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
• 10186703In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer
• 10186701A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.
• 10186693Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10179228New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.
• 10177847When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
• 10170661In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
• 10154879In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.
• 10129576Some vehicles may have a MIL illumination with DTC's P0441, P0442, P0455, or P0456 stored in memory. To determine the location of the evaporative system leak, follow the repair procedure below. P0441 - Evaporative emission control system incorrect purge flow P0442 - EVAP system leak detected (small leak) P0455 - EVAP system leak detected (gross leak) P0456 - EVAP system leak detected (very small leak) NOTE: P0441 is a DTC for purge flow, however, it can be stored when evaporative emissions are leaking from the fuel filler cap. Evaporative emissions leak from the fuel filler cap when the cap is not closed properly after refueling. When diagnosing an evaporative emissions leak from the fuel filler cap, DO NOT TOUCH the fuel filler cap.
• 10111036In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is 2017 Mazda North American Operations, U.S.A. allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
• 10098367In accordance with federal regulations, follow the procedure listed below when replacing a speedometer.note:mazda vehicles are manufactured with tamper-proof speedometers.when a speedometer IS replaced, the new speedometer will read zero (0) miles.this procedure IS extremely important to accurately represent actual vehicle mileage.prior to speedometer removal, complete the information required on the speedometer replace-ment label. Labels can only be ordered through mstore, not mdcs.
• 10098003Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. This IS a normal operating noise of the anti-lock brake system (ABS). Do not attempt any repairs.
• 10097754The multi information display (mid) and navigation system support for diagnostics, parts authorization, and parts exchange require contacting the proper source. Please contact the appropriate source by referring to the following tables.
• 10044209Mazda: variable timing (vvt) noise and/or timing chain noise. The repair procedure flowchart, repair procedure and warranty information have been revised. Also included model mazdaspeed3 model year 2010
• 10043875Mazda: see document search button for owner letter. Due to wear on lock pin hole in vvt rotor or breakage of vvt case, loud ticking noise (knocking/rattle) IS heard, from timing cover and/or valve (cylinder head) cover, when engine IS started after cold condition.
• 10043662Mazda: TPMS warning light illumindated. This may be caused by damage to the valve nut and/or valve stem of the wheel.
• 10041267Mazda: fuel pump or pressure line pipe installation/removal information.
• 10039251Mazda: there IS a rattle noise from the engine due to a stretched timing chain. Updated 4/18/2012.
• 10039250Mazda: while driving at low speeds or having a long idle there IS white/blue smoke from the exhaust pipe. This could be caused by oil problems.
• 10039110Mazda: 2006-2007 mazda speed6. During long periods of slow speed or idling there may be white/blue smoke coming from the tailpipe. There could be problem with the turbocharger.
• 10034005Mazda: determining evaporative system leak location for dtcs p0441, p0442, p0455, p0455. Some vehicles may have a mil illumination with dtcs stored in memory. Updated 4/18/11.

Every Mazda MAZDASPEED3 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.