2012 Mercedes-Benz C350
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › C350 › 2012
These records cover every 2012 Mercedes-Benz C350. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 2012 Mercedes-Benz C350. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2015-2016 E400 Coupe, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2011-2014 E350 Coupe, and 2012-2014 E350 Cabrio vehicles. An incorrect front passenger air bag may have been installed during a prior repair.
Risk and remedy
Risk
An incorrect air bag may not function properly in a crash, increasing the risk of injury.
Remedy
Dealers will replace the front passenger air bag on the affected vehicles, free of charge. Owner notification letters were mailed on September 10, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012 C250, C250 Coupe, C300, C350, C350 Coupe, C63 AMG, and C63 AMG Coupe vehicles equipped with a front passenger air bag assembly replaced under a prior recall. An incorrect replacement front passenger air bag may have been installed.
Risk and remedy
Risk
An incorrect passenger air bag may not provide adequate protection, increasing the risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began July 10, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020060011.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2012 C300 4Matic, C250, C250 Coupe, C350, C350 Coupe 4Matic, C350 Coupe, C63 AMG, C63 AMG Coupe, E350 Coupe 4Matic, E350 Cabrio, E350 Coupe, E550 Cabrio, E550 Coupe, GLK350 4Matic, GLK350, SLS AMG Cabrio, and SLS AMG Coupe vehicles originally sold, or ever registered, in Alabama, California, Florida…
Risk and remedy
Risk
An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the front passenger air bag modules, free of charge. Owners were sent an interim notification in March 2017. Second notices started going out in October 2018 and continue to be mailed as parts become available. Owners may contact MBUSA customer service at 1-877-496-3691
Owner complaints
35 complaints
What owners report most
Latest complaints
- Service brakes
Brake line corrosion issues, related and reported along with the sub-frame assembly corrosion. After getting the sub-frame repaired XXX, corrosion and deformation of the tie rods and control arms caused vibration and noise at speed, and while cornering. Repaired XXX and vehicle inspection…
Brake line corrosion issues, related and reported along with the sub-frame assembly corrosion. After getting the sub-frame repaired XXX, corrosion and deformation of the tie rods and control arms caused vibration and noise at speed, and while cornering. Repaired XXX and vehicle inspection discovered no leaks in the corroded brake lines. After this repair, brake fluid warning light appeared. Very costly repair done at the MB dealership, in [XXX]. This is a common defective issue associated with the corrosion of the subframe, and should be attached to the subframe campaign, and reimbursed by the MFG. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Fuel system, gasoline
The contact owns a 2012 Mercedes-Benz C350. The contact stated while the vehicle was parked, the contact noticed a strong smell of fuel around the exterior of the vehicle. In addition, the contact stated that while driving the vehicle, the fuel odor was extremely strong, and the contact could not…
The contact owns a 2012 Mercedes-Benz C350. The contact stated while the vehicle was parked, the contact noticed a strong smell of fuel around the exterior of the vehicle. In addition, the contact stated that while driving the vehicle, the fuel odor was extremely strong, and the contact could not wind the windows down. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The manufacturer was made aware of the failure. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was 53,000.
- Power train · Suspension
My car’s left side rear subframe is cracked due to corrosion. I started hearing a weird noise a week ago, and my car suddenly veered to the left side when I pressed the brake. I almost crashed my car because the car moved to the left of the yellow line on the road. I searched about this issue on…
My car’s left side rear subframe is cracked due to corrosion. I started hearing a weird noise a week ago, and my car suddenly veered to the left side when I pressed the brake. I almost crashed my car because the car moved to the left of the yellow line on the road. I searched about this issue on Google and found that many C-Class owners (W204 generation) are experiencing the same issue due to the design flaws/defects by Mercedes-Benz. Now I have to pay up to $10,000 for the repair that is due to a defective part. In other countries like the UK and South Korea, this issue is covered by Mercedes-Benz, but in the United States, it is not covered. The repair is done at owner’s expense. I fear driving now because my car steers to the left when I press the brake. The rear subframe must be recalled since this issue is now common to all C-Class models produced in 2008-2014, and if car accidents occur, many people can be killed. I almost crashed my car due to my rotten subframe. Please help.
- Visibility › Sun/moon roof assembly
The contact owns a 2012 Mercedes-Benz C350. The contact stated while driving at an undisclosed speed, the sunroof glass shattered and landed on the sunroof cover. There was no impact on the sunroof that could have caused the sunroof to shatter. The contact and his daughter did not sustain any…
The contact owns a 2012 Mercedes-Benz C350. The contact stated while driving at an undisclosed speed, the sunroof glass shattered and landed on the sunroof cover. There was no impact on the sunroof that could have caused the sunroof to shatter. The contact and his daughter did not sustain any injuries. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 75,000.
- Structure › Body · Suspension
1. The (RH) rear suspension forward link attach point on the rear Suspension Cross-Member (Mercedes-Benz P/N: 204-350-01-41), separated from the sub frame due to internal corrosion of the Suspension Cross-Member. Part available for inspection. 2. When part failed, the RH rear wheel alignment was…
1. The (RH) rear suspension forward link attach point on the rear Suspension Cross-Member (Mercedes-Benz P/N: 204-350-01-41), separated from the sub frame due to internal corrosion of the Suspension Cross-Member. Part available for inspection. 2. When part failed, the RH rear wheel alignment was no-longer fixed; some loss of vehicle steering control was experienced, especially during braking and also turning. 3. Numerous reports of similar episodes of this failure are reported in owners' and maintainers' forums. The dealer service department was familiar with this Suspension Cross-Member part failure. 5. This vehicle passed a Maryland State safety inspection performed by the seller of the vehicle 6 months and 5000 mi prior to the part failure. 6. Part failed with no warning, during normal driving on secondary roads.
- Air bags
TL* takata recall. The contact owns a 2012 mercedes benz C350. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the…
TL* takata recall. The contact owns a 2012 mercedes benz C350. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. Mercedes benz of buffalo located at (8185 main street, williamsville, ny 14221), confirmed parts not available. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
- Air bags
1 year after receiving recall letter for takata airbag recall (phase 4). Mercedes benz of san diego still will not replace the airbag. They will not give a date. They provided a telephone # for mercedes corporate customer care. the menu items for airbag status leads to a call that IS never…
1 year after receiving recall letter for takata airbag recall (phase 4). Mercedes benz of san diego still will not replace the airbag. They will not give a date. They provided a telephone # for mercedes corporate customer care. the menu items for airbag status leads to a call that IS never answered and/or will eventually disconnect. Date below IS the date of the original letter from mercedes. Last call to dealership was 1/13/2020
- Air bags
TL* takata recall. The contact owns a 2012 mercedes-benz C350. The contact received notification of nhtsa campaign number: 17v017000 (air bags). The contact called mercedes-benz of pembroke pines (954- 644-5035, located at 14199 pines boulevard, pembroke pines, fl 33027) and was informed that the…
TL* takata recall. The contact owns a 2012 mercedes-benz C350. The contact received notification of nhtsa campaign number: 17v017000 (air bags). The contact called mercedes-benz of pembroke pines (954- 644-5035, located at 14199 pines boulevard, pembroke pines, fl 33027) and was informed that the parts were not available. The manufacturer was made aware of the issue and was not able to confirm when the parts were to become available. The contact had not experienced a failure. Vin tool confirms parts not available.
- Air bags
TL* takata recall. The contact owns a 2012 mercedes-benz C350. The contact received notification of nhtsa campaign number: 17v017000 (air bags); however, the part for the recall repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall…
TL* takata recall. The contact owns a 2012 mercedes-benz C350. The contact received notification of nhtsa campaign number: 17v017000 (air bags); however, the part for the recall repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact called mercedes-benz stadium (located at 1 amb dr nw, atlanta, ga 30313, 470-341-5000) and was informed that the part was unavailable. The dealer could not provide an estimated time frame for when the parts would become available. The manufacturer was not made aware of the issue. The contact had not experienced a failure.
- Air bags
TL* the contact owns a 2012 mercedes-benz C350. The contact stated that nhtsa campaign number: 17v017000 (air bags) exceeded a reasonable amount of time for repair. The contact received the recall notification in december of 2017. The contact spoke with rallye motor (1600 northern boulevard…
TL* the contact owns a 2012 mercedes-benz C350. The contact stated that nhtsa campaign number: 17v017000 (air bags) exceeded a reasonable amount of time for repair. The contact received the recall notification in december of 2017. The contact spoke with rallye motor (1600 northern boulevard, roslyn, ny 11576, 517-625-1600) and was asked if a letter was received from the manufacturer. The contact informed the dealer that the only letter that was received from the manufacturer was in december of 2017. The manufacturer was not contacted. The contact had not experienced a failure. Vin tool confirms parts not available.
- Air bags
TL* takata recall. The contact owns a 2012 mercedes-benz C350. The contact received notification of nhtsa campaign number: 19v010000 (air bags); however, the part to do the recall repair was not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall…
TL* takata recall. The contact owns a 2012 mercedes-benz C350. The contact received notification of nhtsa campaign number: 19v010000 (air bags); however, the part to do the recall repair was not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Mercedes-benz of tysons corner (8545 leesburg pike, vienna, va 22182, (571) 322-8769) was contacted and confirmed that the parts were not available. The manufacturer was not notified. On several occasions, the air bag warning indicator illuminated. The failure mileage was unknown. Vin tool confirms parts not available.
- Engine
Known fault of rattling noise after engine start for several seconds 07-16-2013 engine 276, engine 278, engine 157 topic number version design group date validity reason for change
- Air bags
2012 mercedes benz C350. Consumer writes in regards to passenger side airbag safety recall. *Ld the consumer stated the manufacturer exceeded a reasonable amount of time completing the recall repair. *Js
- Electrical system · Fuel/propulsion system
The steering wheel locked could not start the car. Car was driven then turned off, when you return to the vehicle, it will not turn on.everything was unresponsive,which wont turn on engine. Had to tow to dealership it cost me 1800.00. So they said the electrical for car was bad. then my fuel…
The steering wheel locked could not start the car. Car was driven then turned off, when you return to the vehicle, it will not turn on.everything was unresponsive,which wont turn on engine. Had to tow to dealership it cost me 1800.00. So they said the electrical for car was bad. then my fuel tank leaked, the componets to the fuel tank all were bad, and l could smell the gas in my car and garage. Cost me 805.00 to repair. Lucky it did not blow up
- Air bags
TL* takata recall. The contact owns a 2012 mercedes-benz C350. The contact received notification of nhtsa campaign number: 17v017000 (air bags). The contact called mercedes-benz of augusta at 706-860-1111 (located at 3061 washington rd, augusta, ga 30907) and was informed that the parts were not…
TL* takata recall. The contact owns a 2012 mercedes-benz C350. The contact received notification of nhtsa campaign number: 17v017000 (air bags). The contact called mercedes-benz of augusta at 706-860-1111 (located at 3061 washington rd, augusta, ga 30907) and was informed that the parts were not available. The manufacturer was made aware of the issue and was not able to confirm when the parts were to become available. The contact had not experienced a failure. Vin tool confirms parts not available.
- Air bags
Takata recall (#17v017) - my issue with this recall IS the unacceptable timeliness in making the necessary repair. In january 2017, I was notified via a recall letter from mercedes that my car's front passenger-side air bag was affected by the takata inflator recall and I would be notified when a…
Takata recall (#17v017) - my issue with this recall IS the unacceptable timeliness in making the necessary repair. In january 2017, I was notified via a recall letter from mercedes that my car's front passenger-side air bag was affected by the takata inflator recall and I would be notified when a repair was available. To date (april 2019), this has not been remedied by mercedes and currently, per their website, there IS no timeline on when this repair can be made. This IS unacceptable in terms of the timeliness of completing this repair given the serious (and potentially deadly) nature of the flaw with the takata inflators should the air bag deploy. When I addressed my concerns regarding the delay in this repair with my local dealership, their advice was to avoid having a person ride in the front passenger seat - which IS impractical and not always possible considering this IS our family car.
- Air bags
TL* takata recall. The contact owns a 2012 mercedes-benz C350. The contact received notification of nhtsa campaign number: 17v017000 (air bags). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer (new country motor cars, inc, 1 weston st…
TL* takata recall. The contact owns a 2012 mercedes-benz C350. The contact received notification of nhtsa campaign number: 17v017000 (air bags). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer (new country motor cars, inc, 1 weston st, hartford, ct 06120, (860)-278-2000) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available. *Tt*jb
- Air bags
Takata recall. I received the racall notice feb.2017 with notification of further notice once parts are available. first of let me address that this IS a huge safety concern and it IS almost 2 years ago since first notice. second of all I am trying to sell my car but do not receive the value I…
Takata recall. I received the racall notice feb.2017 with notification of further notice once parts are available. first of let me address that this IS a huge safety concern and it IS almost 2 years ago since first notice. second of all I am trying to sell my car but do not receive the value I should receive due to the open safety recall. my hands are tight at this point and it can't be right to lose in value of the car due to an outstanding safety call which can't be addressed at this point. what are the next steps in order to solve this problem, especially the safety of my my life and the passengers life. who comes up with the difference in value due to not being able to repair in a timely matter. I believe almost 2 years IS plenty of time to solve the issue. regards
- Air bags
I have received notice that my airbags are at default and have a recall for being defective. Mercedes-benz has told me that they are not able to repair this issue, so I am driving around with airbags that may cause serious injury or death upon an accident. currently I have not been able to have this issue repaired or addressed .
- Air bags
Takata recall. notified of recall in feb 2016, but airbags have not been fixed or replaced.
- Air bags
TL* takata recall. The contact owns a 2012 mercedes-benz C350. the contact received notification of nhtsa campaign number: 16v081000 (air bags); however; the parts to do the repair were unavailable. The dealer (baker motor company of charleston, 843-628-0202) was called and confirmed that the…
TL* takata recall. The contact owns a 2012 mercedes-benz C350. the contact received notification of nhtsa campaign number: 16v081000 (air bags); however; the parts to do the repair were unavailable. The dealer (baker motor company of charleston, 843-628-0202) was called and confirmed that the parts were not available for the recall remedy. The manufacturer was not notified. The contact had not experienced a failure. Vin tool confirms parts not available.
- Air bags
TL* takata recall. The contact owns a 2012 mercedes-benz C350. The contact received notification of nhtsa campaign number: 17v017000 (air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair as…
TL* takata recall. The contact owns a 2012 mercedes-benz C350. The contact received notification of nhtsa campaign number: 17v017000 (air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair as the recall notice was received over a year ago. The dealer was not contacted regarding part availability. The manufacturer was contacted several times and was unable to confirm when the part was to become available. The contact had not experienced a failure. Vin tool confirms parts not available. *Tt
- Air bags
Takata passenger airbag recall in mercedes benz c 350 / 2012 the recall notice was dated march 2017. As of today, mercedes san diego and hoehn mercedes carlsbad have no safe replacement passenger airbags available to install. what's the use of a recall if there IS no better product? I want to protect my passengers, and not sell my car as IS. Please check up on this conundrum.
- Air bags
No resolution since january 2017, I am an active duty soldier often afraid to continue driving for fear of faulty airbag and the aftermath of bodily injury that could potentially occur to me and others.
- Air bags
Takata recall
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
- 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
- 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
- 10205790After starting the engine, the instrument cluster shows the "EBD not available, diagnosis/test stand" message in yellow.
- 10205265Outside mirror fogged.
- 10205239"Anti-theft protection activated".
- 10205237The COMAND unit does not start or the display remains dark.
- 10205225Headlamps fogged.
- 10205215Window lifter and outside mirror on passenger side malfunction after replacement of door control unit.
- 10205154Gasket may settle causing a slight oil leak.
- 10205147Ticking or pulsing noise from high-pressure pump and/or fuel injectors.
- 10187780To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to allegations that the ?590 Mars Red? paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This ?Mars Red? paint is sometimes referred to as ?Fire Opal.? A motion for approval of the settlement was filed with the Court on December 21, 2020. The settlement must receive final approval from the court before it takes effect. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles to repaint any non-plastic exterior surface of a Subject Vehicle because of peeling, flaking, or bubbling of the exterior paint or clear coat. This warranty coverage does not cover repainting necessitated by external influences such as automobile accidents, scratches, or road debris. Warranty coverage will not take effect until the settlement is judicially approved and other events occur. If the settlement becomes effective, coverage will include inspection of the vehicle to diagnose the possible cause of any observed peeling, flaking, or bubbling of the exterior paint or clear coat.
- 10186141NTG5.5: Incorrect time shown on instrument cluster, COMAND display, and analog clock
- 10186135If the customer brakes sharply from a speed of > 30mph, without ABS intervention, there is a single cracking noise from the area of the ESP hydraulic unit
- 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
- 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
- 10167560Fault message in display - Right rear turn signal light inoperative
- 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
- 10167553Combination message: "Clean fuel filter" is displayed. The fault code 162500 (water level message - Bosch) or P226997 (water level message - Delphi) or 171600 (filter load - Bosch) is stored in the engine control unit.
- 10167552Engine does not start, or various fault messages in instrument cluster immediately after engine start and servo assistance is reduced. The following display messages may appear: - Red message "Power Steering Malfunction - See Operator's Manual" including acoustic warning - Red or yellow message "ESP / ABS Currently Unavailable - See Owner's Manual", sometimes with acoustic warning - White message about tire pressure monitor or run flat indicator: "Tire Pressure Loss Warning Defective" or "Tire Pressure Monitor Defective" In addition, the indicator lamps of the following systems may light up: - Brakes / ABS / ESP / ESP Off / engine diagnosis Furthermore: - The chassis CAN is partially or completely disrupted - Several control units (e.g. the electric power steering, ESP, engine etc.) cannot be interrogated or are not listed in the quick test - Various CAN communication errors from other control units may be logged (see list "Control unit / Fault code")
- 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
- 10167546FC 2783 (Friction power of torque converter lockup clutch is too high) or FC 0741 (Actuation of torque converter lockup clutch not possible) stored in transmission control unit. One possible additional customer complaint could be "poor acceleration" e.g. due to engine intervention. This can affect all NAT2FE+ (7G-TRONIC PLUS) vehicles with engines OM651, OM642LS and M278 in the production period from 04/2011 to 02/2012 and with more than 10,000 km. The two fault codes can also occur in combination with rpm sensor faults (see also GI27.50-P-035556). The rpm sensor fault is not connected with this complaint.
- 10167539Engine rattling noise after engine start for several seconds
- 10167536Model X204 (GLK 250 BT) with AMG Styling Package 321. Model Year 2013 Install Tire Fit Kit, Replace Monroney Label
- 10167532A production fault means that the telematics DVD A 166 827 14 00 cannot be used. Because of this the previous telematics DVDs A 204 827 03 65 and A 204 827 10 65 must continue to be used for control unit programming. If required, these are still available for ordering. With XENTRY DVD 03/2014 a new telematics DVD with part number A 166 827 21 00 is being shipped. This telematics DVD replaces the previous telematics DVDs.
Every Mercedes-Benz C350 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.