2006 Mercedes Benz E550

Owner complaints

What owners report most

1. Fuel/propulsion system1
2. Tires1

Latest complaints

• Dec 19, 2012CA64,000 mi
  Fuel/propulsion system
  When the fuel tank IS filled there IS a strong smell of fuel under the drivers side rear wheel base and in the passenger compartment with on occasion a small leakage of fuel on the floor. I have searched the internet and found similar problems on several W211 cars. I contacted the dealership on…

  When the fuel tank IS filled there IS a strong smell of fuel under the drivers side rear wheel base and in the passenger compartment with on occasion a small leakage of fuel on the floor. I have searched the internet and found similar problems on several W211 cars. I contacted the dealership on several occasions to repair the problem and they are no help except to say it will cost around $2000 to repair the problem. I did find that there was some correspondence between the nhtsa this year in april concerning this matter but did not know the outcome and mercedes IS not willing to help at this time. Thank you *tr

• Apr 10, 2010IN20,100 mi
  Tires
  Dear sir/madam, I have a serious complaint against the continental contiprocontact tires that came with my mercedes benz E550 and also the new ones I recently purchased. The car has only 20K miles on it and the side walls on the tires are very weak. I had 1 bubble each develop on 2 of the tires…

  Dear sir/madam, I have a serious complaint against the continental contiprocontact tires that came with my mercedes benz E550 and also the new ones I recently purchased. The car has only 20K miles on it and the side walls on the tires are very weak. I had 1 bubble each develop on 2 of the tires that came with the car after driving over 2 small potholes recently. I also had a sidewall issue on the third tire that came with the car and the new one I just purchased. The recent incident was the worst where both sidewalls burst open when I hit a pot hole. I really think that the quality of the tires IS very poor because it seems to be impacting the sidewalls. I would like to discuss this with someone at the supervisor and director level because this IS a very serious complaint. I am also going to place a complaint with the indiana department of transport for their lack of fixing these pot holes on-time. I am thoroughly disappointed with the road conditions. [xxx] information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(B)(6). *Tr

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Driver Air Bag Circuit High Resistance

  PE10017Opened May 14, 2010Closed Nov 24, 2010
  Mercedes-Benz USA (MBUSA) has reported a high number of warranty claims for air bag warning lamp illumination due to a diagnostic fault code 9103 or 9123 indicating a high resistance in the driver's frontal air bag firing circuit.MBUSA's testing and evaluation have shown that this condition is the result of a faulty…

  Mercedes-Benz USA (MBUSA) has reported a high number of warranty claims for air bag warning lamp illumination due to a diagnostic fault code 9103 or 9123 indicating a high resistance in the driver's frontal air bag firing circuit.MBUSA's testing and evaluation have shown that this condition is the result of a faulty connector (specifically, improper wire crimp) but that it will not prevent proper deployment of the driver's frontal air bag.The faulty connector can cause the air bag circuit resistance levels to exceed the threshold that illuminates the air bag warning lamp, but they do not exceed a higher limit at which proper deployment of the air bag may no longer occur.The agency believes that further expenditure of agency resources does not appear to be warranted at this time.The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.During the investigation, ODI learned that MBUSA will initiate a warranty extension program to address the faulty connectors in subject model year 2005 and 2006 E-Class and other MBUSA model/model year vehicles.This action will extend the warranty coverage for this issue to 10 years or 100,000 miles, whichever occurs first.MBUSA will notify all affected vehicle owners of this action.A bulletin describing this program is available in the investigative file.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10219252In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, is extending the warranty coverage on the fuel filter unit in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: The fuel filter unit might need to be replaced due to minor fuel seepage at the fuel filter flange that could result in fuel odor and/or an activation of the check engine Malfunction Indicator Lamp (MIL). Note that a risk of fire has been ruled out based on the nature of the fuel seepage and the distance to hot components. The vehicles will be visible and flagged in VMI as OPEN on June 10, 2022
• 10215214In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, is extending the warranty coverage on the fuel filter unit in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: The fuel filter unit might need to be replaced due to minor fuel seepage at the fuel filter flange that could result in fuel odor and/or an activation of the check engine Malfunction Indicator Lamp (MIL). Note that a risk of fire has been ruled out based on the nature of the fuel seepage and the distance to hot components.
• 10205147Ticking or pulsing noise from high-pressure pump and/or fuel injectors.
• 10186142Unmotivated Reaction from Park Assist - model series 213 facelift / 238 facelift with option code 235 (active par- king assist) and option code 501 (surround view system)
• 10186141NTG5.5: Incorrect time shown on instrument cluster, COMAND display, and analog clock
• 10186135If the customer brakes sharply from a speed of > 30mph, without ABS intervention, there is a single cracking noise from the area of the ESP hydraulic unit
• 10181124Harsh engagement when changing gear range from P to D or R
• 10181123Harsh engagement when changing gear range from P to D
• 10179951AIRMATIC Fault Message "Max 80 km/ h (50 mph) " In Instrument Cluster
• 10167561Xenon burner inoperative or flickers
• 10167525Apple products (iPhone or iPod) are not charged via the serial USB interface of the COMAND Online control unit (A40/3) in the stowage compartment of the center console.
• 10167489Noise: A rattling noise may be heard from the area of the chain drive for approx. 2-5 seconds after engine start. And/or: Fault code entries in engine control unit: SIM271DE20: P001177 The position of the intake camshaft (cylinder bank 1) deviates from the specified value. The commanded position cannot be reached. P001762 The position of the exhaust camshaft (cylinder bank 1) is implausible in comparison with the position of the crankshaft. The signal comparison is faulty. P001192 The position of the intake camshaft (cylinder bank 1) deviates from the specified value. The function or the instruction is faulty. P001195 The position of the intake camshaft (cylinder bank 1) deviates from the specified value. The mechanical setup is not OK. P001477 The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. The commanded position cannot be reached. P001492 The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. The function or the instruction is faulty. P001495 The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. The mechanical setup is not OK. P001600 The position of the intake camshaft (cylinder bank 1) is implausible in comparison with the position of the crankshaft. P001662 The position of the intake camshaft (cylinder bank 1) is implausible in comparison with the position of the crankshaft. The signal comparison is faulty. P001700 The position of the exhaust camshaft (cylinder bank 1) is implausible in comparison with the position of the crankshaft.
• 10167000Surface damage on steering wheel trim
• 10166976Message in instrument cluster "DISTRONIC PLUSCurrently Unavailable - See Owner's Manual"
• 10166975This Customer 1 Action has been initiated because certain mbrace subscribers were recently contacted by mbrace informing them that they need to have an i-button call performed to ensure their mbrace device has registered with the Verizon Telematics systems. If the i-button call failed or if the customer was unable to perform the i-button call, the mbrace agent instructed the customer to make an appointment with their dealer to have the issue corrected and/or i-button call performed. The vehicles impacted range from model year 2002 to 2014.
• 10166103The controls on the partially electric seat adjustment switch stick or are loose or broken.
• 10166092Dynamic seat control is not functioning correctly and/or air cushions do not inflate fully.
• 10166090Possible complaints: 1. Memory function of electric seat fore/aft adjustment not functioning. 2. Seat fore/aft adjustment with easy entry/exit feature not functioning. 3. Head restraint presetting not functioning. 4. Seat fore/aft adjustment can only be adjusted for 2 sec with the seat adjustment switch (seat can only be adjusted in longitudinal direction in fits and starts). 5. Function "Collision avoidance when folding down the rear seat backrest" not functioning (seat fails to move forward when the rear seat backrest is folded down).
• 10166084Rubbing noises at the point at which the covering rubs against the cover. Only occurs on vehicles with the sport package .
• 10166083Rubbing noises arise between the covering and cover of the sidebag
• 10166082Noises from area of seat adjuster or cushion frame.
• 10166081Noise complaints when load on backrest frame changes. Affects the driver and front passenger seats. Also perform the remedial action if you are performing work on: - backrest frame - backrest cover or - guide rail of head restraint. If the backrest frame is exposed as a result, the actions must always be performed in order to avoid follow-up repairs.
• 10158329Oil in engine wiring harness
• 10151959Seat belt extender toothed rack sluggish or makes noises
• 10151948Display of suspension setting in head unit implausible
• 10151924Liftgate intermittently does not open fully
• 10135628iPhone mobile phone: Various complaints after software update to iOS8
• 10135598Engine diagnosis warning lamp lights up in instrument cluster, fault code U145400: "Implausible data were received from the ethanol sensor"
• 10056470Xentry (mercedes): combination of fault codes p060c00 and/or p060600, causing various transmission symptoms due to central processing unit, software induced internal control unit fault IS detected. Model 212.098, 212.298, 212. 095, 212.195. Updated 1/6/15.
• 10051540Xentry: m271.8 evo engine has poor accelerator response- lack of power under full load and high rpm. Engine diagnosis warning lamp (cel) lights up, vehicle IS in limp-home mode (may or may not be intermittent).
• 10050860Mercedes (xentry): the inside door handle, on front door, IS inoperative due to the bowden cable becoming unhooked from clip and needs to be replaced. Model 207. No model years listed.
• 10042608Xentry(mercedes): bulletin regarding the 4 spoke steering wheel chrome badges on driver airbag that are peeling and/or discolored.
• 10041653Xentry(mercedes): malfunctioning of the airmatic in the display. Updated 3/9/12.

Every Mercedes Benz E550 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.