2009 Mercedes Benz GL450
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes Benz › GL450 › 2009
These records cover every 2009 Mercedes Benz GL450. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
3 recalls name the 2009 Mercedes Benz GL450. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2006-2012 ML, GL, and R-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. Moisture may accumulate and cause corrosion in the brake booster housing unit, which can result in reduced brake performance or brake failure.
Risk and remedy
Risk
Reduced brake performance or brake failure can increase the risk of a crash.
Remedy
Owners are advised not to drive their vehicles until the remedy has been performed. Dealers will remove the rubber sleeve, inspect the brake booster, and as necessary, replace the brake booster. All repairs will be performed free of charge. Owner notification letters were mailed on May 24, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MMUSA's number for this recall is 2024050001/2. This recall is an expansion of previous recall number 22V-315.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2006-2012 ML-Class, GL-Class, and R-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. Moisture may accumulate and cause corrosion in the brake booster housing unit, which can result in reduced brake performance or brake failure.
Risk and remedy
Risk
Reduced brake performance or brake failure can increase the risk of a crash.
Remedy
Owners are advised not to drive their vehicles until the remedy has been performed. Dealers will remove the rubber sleeve, inspect the brake booster, and as necessary, replace the brake booster. All repairs will be performed free of charge. Owner notification letters were mailed June 30, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers for this recall are 2022050014, 2022050015 2022090006, & 2022090007.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2009-2010 ML320 BlueTec 4Matic, GL320 BlueTec 4Matic and R320 CDI 4Matic, 2011 E350 Cabriolet and E550 Cabriolet, 2009-2011 ML350, ML350 4Matic, ML550 4Matic, ML63 AMG, and C63 AMG, 2010-2011 ML450 4Matic Hybrid, E350 Coupe, E350 4Matic, E550 Coupe, E550 4Matic, and E63 AMG, 2011-2012 GL350…
Risk and remedy
Risk
In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
MBUSA will their notify owners, and Fiat Chrysler will notify the affected Chrysler owners. Dealers for the respective brands will replace the driver's frontal air bag module, free of charge. This recall began November 2016. Mercedes-Benz owners may contact MBUSA customer service at 1-800-367-6372 and Chrysler owners may contact Fiat Chrysler customer service at 1-800-853-1403.
Owner complaints
15 complaints1 involved a crash
What owners report most
Latest complaints
- Engine · Service brakes, hydraulic · Suspension
The contact owns a 2009 Mercedes-Benz GL450. The contact stated that the ABS and check engine warning lights were illuminated, and the struts had failed. The vehicle was taken to the dealer to be repaired under NHTSA Campaign Number: 22V315000 (Service Brakes, Hydraulic); however, the dealer…
The contact owns a 2009 Mercedes-Benz GL450. The contact stated that the ABS and check engine warning lights were illuminated, and the struts had failed. The vehicle was taken to the dealer to be repaired under NHTSA Campaign Number: 22V315000 (Service Brakes, Hydraulic); however, the dealer informed the contact that the vehicle needed to be diagnosed prior to the recall repair, due to the failure. The contact declined to pay the diagnostic fee, and the vehicle was not diagnosed or repaired. The contact stated that the dealer failed to honor the recall repair. The manufacturer was not made aware of the issue. The failure mileage was approximately 156,000.
- Electrical system · Engine · Service brakes, hydraulic
The contact owns a 2009 Mercedes-Benz GL450. The contact stated while driving at an undisclosed speed, the brake pedal was depressed, and the vehicle started shuddering. The check engine warning light was illuminated. The vehicle was towed to the dealer who informed the contact that the vehicle was…
The contact owns a 2009 Mercedes-Benz GL450. The contact stated while driving at an undisclosed speed, the brake pedal was depressed, and the vehicle started shuddering. The check engine warning light was illuminated. The vehicle was towed to the dealer who informed the contact that the vehicle was not safe to drive. The vehicle was towed to the dealer where the recall repair of NHTSA Campaign Number: 22V315000 (Service Brakes, Hydraulic) was completed; however, after the recall repair was completed, the vehicle failed to start. The dealer replaced the battery and completed other unknown repairs on the vehicle. The contact stated that he picked up and drove the vehicle to his residence; however, the vehicle failed to start the next day. The vehicle was towed to the dealer. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that they would reimburse the rental car cost. The failure mileage was approximately 143,300.
- Unknown or other
I was driving 70 down an interstate a Saturday around 4:30 pm and heard a noise as if my sunroof opened a bit, then I heard a loud pop and a rush of air and looked in my rearview mirror and didn't see anything, I looked up seen the sunroof was gone. All I could think about is that could have really…
I was driving 70 down an interstate a Saturday around 4:30 pm and heard a noise as if my sunroof opened a bit, then I heard a loud pop and a rush of air and looked in my rearview mirror and didn't see anything, I looked up seen the sunroof was gone. All I could think about is that could have really caused a serious accident. Glad no one was around me at the time. I doubled back twice and could not find the sunroof glass. I got home and put a couple pieces of cardboard and plastic down and duct taped it before the snow storm hits. A day after and my heart is still racing knowing that could have cause a wreck.
- Air bags · Exterior lighting · Service brakes
Takata inflators : the srs light IS continuously staying on in the vehicle. as soon as the vehicle IS started the light comes on and does not go off until the vehicle goes back off.
- Electronic stability control (esc) · Suspension
I am having issues with my suspension. I've had to replace it twice in 1 year. A recall should be issued on this.
- Suspension
I purchased my mb gl450 in 2010 and at that time it was covered as a pre-owned mb vehicle. Under the warranty, I had the air ride suspension fixed twice. Once on front left and right. After the warrant expired, I have had to do both sides of my suspension again. Now the front left has failed and…
I purchased my mb gl450 in 2010 and at that time it was covered as a pre-owned mb vehicle. Under the warranty, I had the air ride suspension fixed twice. Once on front left and right. After the warrant expired, I have had to do both sides of my suspension again. Now the front left has failed and needs to be repaired. I have read my blogs and posts about this mb suspension defect and want hope the nhtsa can push mb to issue a recall to fix this failed product.
- Air bags
Takata recall: still no remedy available per mercedes benz; first notice received 2/2017.
- Air bags
This complain IS about the recall report as below feb 11,2016 manufacturer recall number2016020003 nhtsa recall number16v081 description: I have never been contacted by the manufacturer about this recall. Apparently, the manufacturer has failed or IS unable to remedy this safety recall for your vehicle in a timely manner.
- Air bags
Takata recall my vehicle IS part of the recall and there IS still no fix for my problem. This IS extremely dangerous, we are driving with a ticking time bomb.
- Air bags
Takata recall the recall was instituted february 2016, yet to date there has been no remedy offered by the manufacturer and no indication as to when they will be replacing the airbags.
- Air bags
Takata recall a recall notice was issued for my vehicle's (2009 benz gl450) airbags. However, takata / mercedes benz do not have a remedy available for my vehicle despite the recall date being more than 1 year ago.
- Unknown or other
We had trouble towing our travel trailer, we looked under our car and the weld was broken on our hitch. We took it to the dealership and their inspection confirmed it was a "bad weld".they want us to pay $900 to fix. this IS the exact same problem and hitch that was recalled in 2007 and 2008, so…
We had trouble towing our travel trailer, we looked under our car and the weld was broken on our hitch. We took it to the dealership and their inspection confirmed it was a "bad weld".they want us to pay $900 to fix. this IS the exact same problem and hitch that was recalled in 2007 and 2008, so mercedes continued to use the same hitch and weld in year 2009 and now it has failed after 4 times towing. The rust on our picture indicates the weld had failed much prior to us realizing it.
- Air bags
TL* the contact owns a 2008 mercedes benz gl450. The contact received notification of nhtsa campaign number: 16v081000 (air bags) however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Part distribution disconnect.
- Unknown or other
I was driving on my way home from work today 2/3/2017 and I was merging onto highway when I heard a loud explosion. I then saw that my sunroof had shattered and was bowed out. There IS a large hole in the center of the sunroof and the rest of the glass IS spiderwebbed. Nothing had hit my car or my…
I was driving on my way home from work today 2/3/2017 and I was merging onto highway when I heard a loud explosion. I then saw that my sunroof had shattered and was bowed out. There IS a large hole in the center of the sunroof and the rest of the glass IS spiderwebbed. Nothing had hit my car or my sunroof. I was only going about 15 mph as I was still on a on ramp. It was very scary and dangerous. I called mercedes who IS no help. They need to recall this or be held responsible. This could have caused me to crash or if my sunroof cover was opened I would have been showered in glass.
- Air bags
TL* takata recall. The contact owns a 2009 mercedes-benz gl450. The contact received notification of nhtsa campaign number: 16v081000 (air bags) and stated that the part was not available within a reasonable time frame to schedule the recall repair. The dealer did not give a specific date for when…
TL* takata recall. The contact owns a 2009 mercedes-benz gl450. The contact received notification of nhtsa campaign number: 16v081000 (air bags) and stated that the part was not available within a reasonable time frame to schedule the recall repair. The dealer did not give a specific date for when the part would become available. The manufacturer could not provide an estimated date for when the contact's vehicle would receive the recall repair. The contact was not experiencing a failure. Vin tool confirms parts not available. updated 05/10/17*lj updated 10/10/2017*js
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10248173Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2009-2012 GL-Class, ML-Class, R-Class, and S-Class (164/166, 251, 221 platforms) vehicles, the coding for the engine control unit does not correspond to the specifications as part of the BlueTEC update diesel field measure (aka Emission Modification). This could result in the VIN number not being read out from the vehicle. This could affect the vehicle smog check. MBUSA will conduct an Emission Service Campaign in which an authorized Mercedes-Benz dealer will update the SCN coding for the engine control unit on the affected vehicles.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10235996Additional information around the recent recall announcement affecting approximately 705,983 Mercedes-Benz passenger vehicles involving Takata driver-side airbags containing PSDl-5 type inflators
- 10235978Recall Campaign announcement for Takata driver airbags.
- 10205249No cooling output, fault code 9006 stored in air conditioning control unit.
- 10205233Mobile phone cotacts are not transferred completely.
- 10205147Ticking or pulsing noise from high-pressure pump and/or fuel injectors.
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10171637Retrofitted front door exit lamps with logo projection flicker
- 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
- 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
- 10167546FC 2783 (Friction power of torque converter lockup clutch is too high) or FC 0741 (Actuation of torque converter lockup clutch not possible) stored in transmission control unit. One possible additional customer complaint could be "poor acceleration" e.g. due to engine intervention. This can affect all NAT2FE+ (7G-TRONIC PLUS) vehicles with engines OM651, OM642LS and M278 in the production period from 04/2011 to 02/2012 and with more than 10,000 km. The two fault codes can also occur in combination with rpm sensor faults (see also GI27.50-P-035556). The rpm sensor fault is not connected with this complaint.
- 10167040This Service Campaign has been initiated because Daimler AG (DAG), the manufacturer of Mercedes-Benz vehicles, has determined that the mbrace software does not correspond to current production configuration. An authorized Mercedes-Benz dealer will update the mbrace control module software at the next workshop visit.
- 10166988Collision Prevention Assist (CPA) may warn for no obvious reason (optical and/or acoustic warning message).
- 10166976Message in instrument cluster "DISTRONIC PLUSCurrently Unavailable - See Owner's Manual"
- 10166975This Customer 1 Action has been initiated because certain mbrace subscribers were recently contacted by mbrace informing them that they need to have an i-button call performed to ensure their mbrace device has registered with the Verizon Telematics systems. If the i-button call failed or if the customer was unable to perform the i-button call, the mbrace agent instructed the customer to make an appointment with their dealer to have the issue corrected and/or i-button call performed. The vehicles impacted range from model year 2002 to 2014.
- 10166097Electric motor for the folding rear backrest of the 3rd seat row is inoperative or makes noises during adjustment
- 10166096The release loop of the Easy Entry seat in the 2nd seat row is awkward to operate as it is difficult to access
- 10135970Delayed 2-3 Upshift
- 10135716Headlamp lights up sporadically
- 101356252nd seat row Power Easy Entry function impairment of backrest folding
- 10059536Summary to be provided on a future date.
- 10042607Xentry(mercedes): bulletin provided regarding control unit detecting an undervoltage after buckling up (belt slack elimination) during seat belt adjustment sequence. Updated 5/23/12.
- 10041269Mercedes benz: there IS a software problem relating to the tank heater lines.
- 10041024Mercedes-benz: the fuel level indicator IS wrong.
- 10039256Mercedes-benz: the malfunction light IS on with multiple possible trouble codes stored. There could be a problem with the camshaft and/or scoring of a piston.
- 10038977Mercedes-benz: the auto-transmission switches to limp home mode or has no power. There are multiple possible fault codes. A piston may be damaged.
- 10038955Mercedes-benz: at the front wheel bearing there IS a loud knock sound when going around a corner at slow speeds. There IS an insufficient fit at the bearings. Updated 10/14/11. Updated 6/19/13.
- 10038227Mercedes-benz: the starter clicks but does not crank when trying to start. A voltage dip IS causing the ignition procedure to fail.
- 10038218Mercedes-benz: software update for heater lines.
- 10037985Mercedes-benz: the load compartment roller blind has catch bolts loose or broken from improper force when using.
- 10037408Mercedes-benz: shock absorber procedure.
- 10034626Mercedes (xentry): rear window wiper fails to function or stops intermittently. Low voltage cutoff relay in the rear fuse and relay block (rear (srb). Only part number A164 540 02 72 causes this condition. Check part number of rear srb, if the part number IS A164 540 02 72, follow procedure to resolve. Models 164.175/186 and 251.165/175. No model years listed.
- 10034306Mercedes: airbag durability and reliability. Air bag srs control module (N2/2) does not have a set shelf life and will normally be reliable for the life of a vehicle. With 164, 216 221, 251 and newer, the airbag control unit can be reset five times. With modes 202, 210 and newer, the airbag control unit can be reset three times. Earlier models would have to have their airbag control unit and triggered restrain components changed only after an accident. No models or model years listed.
- 10034152Mercedes: battery symbol and service required (in white). Fault message IS displayed if the charge level IS too low or the park pawl additional battery IS defective. In addition fault code fc 9061 and/or fc 9062 IS stored in the front sam.
Every Mercedes Benz GL450 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.