2013 Mercedes-Benz GL450

Recalls

3 recalls name the 2013 Mercedes-Benz GL450. Newest first.

• Communication

  Nov 1, 2019NHTSA 19V78700024,226 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…

  Risk and remedy

  Risk

  An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.

  Remedy

  MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.

  Full recall details →

• Suspension › Front

  Apr 27, 2018NHTSA 18V2720009,725 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML350 Bluetec 4Matic and ML550 4Matic, 2012-2015 ML63 AMG 4Matic and ML350 4Matic, 2013-2016 GL350 Bluetec 4Matic, GL550 4Matic and GL63 AMG 4Matic, 2017 GLS350d 4Matic, GLS450 4Matic, GLS550 4Matic and GLS63 AMG 4Matic, 2015 ML400 4Matic, 2016 GLE400 4Matic, GLE350 4Matic, GLE63 AMG 4Matic…

  Risk and remedy

  Risk

  The leaking oil in the presence of an ignition source can increase the risk of a fire.

  Remedy

  MBUSA will notify owners, and dealers will correct the oil level as necessary and replace the reservoir sealing cap to prevent oil foam from leaking out, free of charge. The recall began August 30, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018070015.

  Full recall details →

• Seat belts

  Apr 29, 2013NHTSA 13V166000256 vehicles

  Mercedes-Benz USA, LLC (Mercedes) is recalling certain model year 2013 GL350 BlueTEC, GL450 4MATIC, GL550 4MATIC, and GL63 AMG vehicles manufactured May 15, 2012 through October 4, 2012. The second row seat belt anchor fitting bolts may not be properly torqued.

  Risk and remedy

  Risk

  If the bolts are not properly torqued, the seat belt anchor bolts may continue to loosen and in the the event of a crash, the belted occupant may not be properly restrained, increasing the risk of injury.

  Remedy

  Mercedes-Benz will notify owners and dealers will check, and tighten the bolts of the seat belt anchor fittings, as necessary, free of charge. The recall campaign began on May 24, 2013. Owners may contact Mercedes-Benz at 1-800-367-6372.

  Full recall details →

Owner complaints

What owners report most

1. Engine9
2. Electrical system8
3. Suspension5
4. Seats5
5. Unknown or other4
6. Service brakes4
7. Power train3
8. Wheels2
9. Seat belts2
10. Air bags2

Latest complaints

• May 21, 2026FL
  Unknown or other

  I bought the vehicle with 104k miles. When hooked to a computer it shows 177k. The odometer was tampered with

• Mar 13, 2026SC
  Engine
  I was driving along in my 2013 MB GL450 with the M278 engine when the engine stopped. I had it towed to my home and checked it out. I had a suspicion the engine was seized. I eventually had to towed to my closest MB dealership for evaluation. The engine was seized. Their further investigation…

  I was driving along in my 2013 MB GL450 with the M278 engine when the engine stopped. I had it towed to my home and checked it out. I had a suspicion the engine was seized. I eventually had to towed to my closest MB dealership for evaluation. The engine was seized. Their further investigation revealed that a wrong oil filter had been installed when the oil was changed 5 months and 3000 miles earlier. I tried to find out what this wrong filter would cause. I asked the dealership and then MB and got no response. I suspect if this filter caused the issue it would have been an oil pressure issue. The car gave no indication of anything wrong prior to engine seizing. I got no message on the display and when switching on the switch there is no indicator on the dashboard to indicate anything about oil pressure. There is no "oil can" that pops up red indicating an oil pressure issue. To this day have no idea why the engine seized other than an improper oil filter.

• Aug 9, 2024CO
  Unknown or other
  While driving on the freeway, we picked up a big screw in our tire which immediately deflated. To continue our journey, we wanted to replace the tire with the spare wheel. To do that, we used the floor jack that came with the car and this would have been it's first use. While attempting to lift the…

  While driving on the freeway, we picked up a big screw in our tire which immediately deflated. To continue our journey, we wanted to replace the tire with the spare wheel. To do that, we used the floor jack that came with the car and this would have been it's first use. While attempting to lift the vehicle, the threaded bushing of this scissor type floor jack completely stripped (see picture). Not only is this super dangerous to have such a floor jack included, but if could have left us stranded for a very long time in case we would have been more remotely. I would suggest to investigate these floor jacks whether the pose any safety hazards and if make Mercedes-Benz replacing them free if charge.

• Mar 24, 2024NJ
  Back over prevention › Warnings · Electrical system · Power train
  I am reaching out to bring to your attention a significant manufacturing flaw in the Mercedes GL450 model, which poses a severe risk to both vehicle functionality and passenger safety. The issue pertains to water infiltration into the battery compartment situated beneath the front passenger seat…

  I am reaching out to bring to your attention a significant manufacturing flaw in the Mercedes GL450 model, which poses a severe risk to both vehicle functionality and passenger safety. The issue pertains to water infiltration into the battery compartment situated beneath the front passenger seat and concealed beneath the carpet. Even minor rainfall or streetwater has been found to breach this compartment, causing extensive damage to the vehicle's electronic systems. This results in highly precarious and unpredictable behavior, endangering both occupants and road users. As a poignant example, my own GL450, a 2013 model, has exhibited alarming symptoms. Despite being securely in "PARK" mode, upon simply opening the car door, it displays a distressing message: "Transmission Not in P Risk of Vehicle Rolling Away." Furthermore, the transmission intermittently ceases to shift from "P," presenting an imminent hazard to myself and my children. Despite numerous attempts to engage with Mercedes Headquarters regarding this critical matter, regrettably, they have declined to address the issue, citing its expiration beyond the warranty period. However, extensive research indicates that this flaw is pervasive among GL450 owners, as evidenced by discussions on various automotive forums, such as: [XXX] [XXX] I am profoundly concerned about the gravity of this situation and implore you to take immediate action to rectify this widespread issue. Please feel free to contact me at your earliest convenience at [XXX] . I am more than willing to provide further details regarding my experiences and observations. I earnestly anticipate your prompt response and resolution to this matter. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• Mar 22, 2024NJ78,000 mi
  Power train
  The contact owns a 2013 Mercedes-Benz GL450. The contact stated that the vehicle was parked; however, while opening the door to enter the vehicle, the message "Transmission not in P, Risk of Vehicle Rolling Away" was displayed. The contact turned off and restarted the vehicle, and moved the gear…

  The contact owns a 2013 Mercedes-Benz GL450. The contact stated that the vehicle was parked; however, while opening the door to enter the vehicle, the message "Transmission not in P, Risk of Vehicle Rolling Away" was displayed. The contact turned off and restarted the vehicle, and moved the gear shifter in and out of park(P); however, the failure persisted. The contact stated that other unknown messages were displayed. Additionally, the contact stated that he became aware that there was water accumulation underneath the front passenger's side seat. The contact stated that there was water on the battery and electrical wiring. The vehicle was towed to the dealer to be diagnosed. The vehicle was not diagnosed or repaired. The Insurance Company later informed the contact that the water had frozen because the dealer had not diagnosed the vehicle or drained the water. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 78,000.

• Oct 3, 2023CA
  Electrical system

  Suround cameras are not able to see at night and backup lights not bright enough to see.

• Aug 1, 2023VA106,000 mi
  Steering
  The contact owns a 2013 Mercedes-Benz GL450. The contact stated while driving 35 MPH, the steering wheel became difficult to turn. The contact stated there was no warning light illuminated. The contact had experienced the failure five times. The contact took the vehicle to the local dealer however…

  The contact owns a 2013 Mercedes-Benz GL450. The contact stated while driving 35 MPH, the steering wheel became difficult to turn. The contact stated there was no warning light illuminated. The contact had experienced the failure five times. The contact took the vehicle to the local dealer however, the technician was unable to duplicate the failure. The vehicle was not repaired. The contact took the vehicle to an independent mechanic to be diagnosed. The contact was informed that the steering shaft needed to be replaced. The vehicle was not repaired due to the parts being on backorder. The manufacturer had been informed of the failure. The failure mileage was approximately 106,000. The dealer stated the steering shaft failing because of corrosion. At this moment they suggested the part is not available so they wanted to fix my car with a used part.

• Jun 26, 2023CT
  Engine
  Exhaust valve not working properly and the result of an engine misfire. Mercedez sent us a warranty letter to extend the warranty for this issue 6 months after our warranty expired even though you can find online this has been a known issue for our model of car and year, GL450 2013. There are tons…

  Exhaust valve not working properly and the result of an engine misfire. Mercedez sent us a warranty letter to extend the warranty for this issue 6 months after our warranty expired even though you can find online this has been a known issue for our model of car and year, GL450 2013. There are tons of online forums and threads from Mercedez Benz owners about this manufacturer issue. This should not fall under purchasing an extended warranty or in our case a $17,000 bill to fix the issue on a car with only 70,000 miles on it. This should be a recall.

• Mar 3, 2023MA110,000 mi
  Fuel system, gasoline
  The contact owns a 2013 Mercedes-Benz GL450. The contact stated that while driving at an undisclosed speed, the vehicle lost motive power while the fuel gauge was at a quarter tank. An unknown message was displayed. AAA arrived on the scene and added fuel to the vehicle. The contact was able to…

  The contact owns a 2013 Mercedes-Benz GL450. The contact stated that while driving at an undisclosed speed, the vehicle lost motive power while the fuel gauge was at a quarter tank. An unknown message was displayed. AAA arrived on the scene and added fuel to the vehicle. The contact was able to restart the vehicle; however, the failure recurred on two separate occasions while the fuel gauge was at a quarter tank. The vehicle was taken to the dealer, where it was diagnosed that the fuel gauge module and fuel pump needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and informed the contact that the vehicle was out of warranty. The manufacturer advised the contact to file a complaint with the NHTSA Hotline. The failure mileage was approximately 110,000. The contact stated that the failure has occurred twice. The vehicle is not a part of a recall for an engine stalling risk which the exact issue that is happening. The vehicle has not been repaired and the manufacturer has not offered any assistance yet.

• Nov 26, 2022NY
  Engine

  The engine failed under 100k miles after being properly maintained according to the manufactures guidelines.

• Aug 4, 2022GA
  Electrical system · Engine
  2013 Mercedes-Benz GL450; it started with the activation of the vehicle's check - engine light. The Mercedes-Benz service advisor diagnosed the issue as oil intrusion into the vehicle's engine wiring harness. The estimated cost to repair was quoted as $7,0000.00. This resulted in the…

  2013 Mercedes-Benz GL450; it started with the activation of the vehicle's check - engine light. The Mercedes-Benz service advisor diagnosed the issue as oil intrusion into the vehicle's engine wiring harness. The estimated cost to repair was quoted as $7,0000.00. This resulted in the replacement of the engine wiring harness, four (4) Lambda sensors, four (4) camshaft hall sensors and four (4) camshaft solenoids. This trouble could cause engine failure or misfire if not corrected. Driving the MB GL450 in this condition is a safety issues for anyone driving on the road. Researching on the internet about MB GL450/550 engine oil intrusion into the engine wiring harness is a common problem.

• Mar 12, 2022MD
  Suspension

  Unknown:The road adaptive tire pressure sensors are off and the air suspension is malfunctions.At the cost of this model I would expected a little more class of safety measures.

• Aug 2, 2021MD1 injury
  Unknown or other
  As you stated above the air conditioning IS not a reason a driver would loose control unless you have a mercades that IS leaking gas and my kids and passangers are sick and passing out and so am i. this has been going on almost 3 years. Goes to dealership and then sits because they never fix it.…

  As you stated above the air conditioning IS not a reason a driver would loose control unless you have a mercades that IS leaking gas and my kids and passangers are sick and passing out and so am i. this has been going on almost 3 years. Goes to dealership and then sits because they never fix it. finally a law suit with people having same problem entered the class action suit nothing. Took the car back and they say now the toxic gas leaking out of faulty a/c units that mercedes was sued and consumers won but now won't fix the problem. So I now have severe asthma my kids now have breathing issues and won't drive a sick car. a/c units are to be contained and hold anti-freeze that if inhaled as it IS leaking out of the non contained unit IS toxic, a carcinogen, same toxin used in nerve gas and it IS deadly and mercedes does not fix it or care. this has gone on for years and IS a nightmare. They made a settlement but then they don't do what the judge set forth in the settlement agreement and I am not the only one;

• Jun 9, 2021NY
  Suspension · Wheels
  Driver's side tire continues to leak air - note low tire pressure even with new tire replacement. Airmatic Suspension failure. Rear airbag suspension airbag. Compression also failed. Several complaints to dealer advising the car was bouncing up and down while in drive. Took vehicle to the…

  Driver's side tire continues to leak air - note low tire pressure even with new tire replacement. Airmatic Suspension failure. Rear airbag suspension airbag. Compression also failed. Several complaints to dealer advising the car was bouncing up and down while in drive. Took vehicle to the shop with suspension complaints at the end of April 2021. We were told they did not find an issue with suspension but saw an issue with the sway bar. This cost $549.00. The week we brought the car home it was still bouncing up and down and we contacted the dealer again and was advised they did not find anything wrong. Within 2 weeks of having the vehicle, I was driving and the vehicle was violently bouncing up and down even traveling at a low level. We took the vehicle back and have not been advised now that they see the malfunction light for the suspension on they realize that's the issue. The suggested cost to repair only the rear is $4k. If the front and rear need repairs it over $7k. The issue is it appears this is a known issue for the Airmatic system and with a vehicle in this price range and under 90k miles - appears to be a issue with manufacturing. I was also advised this repair is no longer covered on their extended warranty.

• Oct 14, 2020GA100,456 mi
  Suspension
  When activation of the suspension lift system. Compressor IS cooling then a malfunction message appears on the screen. vehicle shakes violently in the rear up and down at low and high speeds and over any small bumps in the road. This concerns me for the safety of other owners whom may have the…

  When activation of the suspension lift system. Compressor IS cooling then a malfunction message appears on the screen. vehicle shakes violently in the rear up and down at low and high speeds and over any small bumps in the road. This concerns me for the safety of other owners whom may have the same problem. 2013 mercedes benz GL 450 IS the model I own currently and ive been having this problem for the past 3 months and I'm almost scared to drive it for fear of something catostrophic happening. Please look into this problem. Even when park and activating the suspension system the error message still appears.. I had a independant mechanic say its the rear air bags and the compressor that has to be replaced because of it being a 4 matic model the air line from the compressor IS not supplying the rear suspension with enough air to lift the vehicle thus causing the problem that we have.

• Feb 4, 2020MD
  Air bags

  A defective rear middle passenger seat airbag alert / sign comes on once I turn the engine on. It stays on through out the drive. I suspect the airbag IS defective

• Jul 27, 2019CT100,000 mi
  Engine · Power train · Seat belts
  This car has lot of issues with water pump, radiator leak, lot of engine problems. oil leak it's got less than 100,000 miles. Radiator hoses leak. Car stopped on mass pike going to albany, ny took it to benz of albany they said engine misfires needs engine replacement and it would cost $47,000 to…

  This car has lot of issues with water pump, radiator leak, lot of engine problems. oil leak it's got less than 100,000 miles. Radiator hoses leak. Car stopped on mass pike going to albany, ny took it to benz of albany they said engine misfires needs engine replacement and it would cost $47,000 to replace. Very very bad engines. I left a voicemail on benz customer service and no one called back or send me any type of recalls. Very bad service.

• Jul 26, 2019TX88,000 mi
  Electronic stability control (esc) · Suspension · Unknown or other

  Upon acceleration after a complete stop there are several seconds of hesitation to accelerate and loud clicking sounds that neighboring cars can hear. After doing online research, this issue IS not limited to gl450. Other owners have expressed the same concern in other models: 2008 C300, 2009 C300, 2015 C300, 07 gl450, 03 gl450.

• May 24, 2019OH87,500 miFire
  Suspension
  TL* the contact owns a 2013 mercedes benz gl450. The contact stated that while operating the vehicle, the rear section would bounce up and down violently due to a faulty rear air suspension. In addition, an electrical burning odor was present inside the vehicle and the arm rest was extremely hot to…

  TL* the contact owns a 2013 mercedes benz gl450. The contact stated that while operating the vehicle, the rear section would bounce up and down violently due to a faulty rear air suspension. In addition, an electrical burning odor was present inside the vehicle and the arm rest was extremely hot to the touch. The cause of the failure was not determined. The local dealer and manufacturer were not notified of the failure. The failure mileage was 87,500.

• Mar 8, 2019NY58,000 mi
  Electrical system · Engine

  Engine harness wires contamination in me, cause sensors damage and engine problems to start up right normal dealer want to charge me 14K for service and repair , every time I start the car it sounds like it take time to start and I get the check engine evertime I start the car

• Jan 2, 2019GA75,000 mi
  Visibility › Sun/moon roof assembly
  At 9:22am on the morning of january 2, 2019, my SUV was parked in my driveway. It was overcast, calm conditions, and around 52. I unlocked my vehicle, got in, started the engine, and closed the driver's door normally. One second later, I heard an explosion as the sunroof exploded. There was no…

  At 9:22am on the morning of january 2, 2019, my SUV was parked in my driveway. It was overcast, calm conditions, and around 52. I unlocked my vehicle, got in, started the engine, and closed the driver's door normally. One second later, I heard an explosion as the sunroof exploded. There was no evidence of anything haven fallen on the vehicle nor any evidence that anyone had tampered with my SUV. I had last driven the vehicle the afternoon of december 31, 2018 in conditions similar to those described above. I have no recollection of my vehicle being struck by any objects in recent years. This was a sudden and very unexpected occurrence.

• May 28, 2018PA
  Electrical system

  Blind spot assistance becomes disable and minutes later the blinkers stop working. This occurs while the car IS in motion, and appears more frequent on cold weather. This can only be resolved by turning off the car and restarting. Dealership refers it to be an electrical problem with the blind spot assistance. Now it has disable the keyless door opening and button start

• May 17, 2016CA24,000 miCrash2 injuries
  Air bags
  TL* the contact owned a 2013 mercedes-benz gl450. While driving approximately 5 mph in a parking lot, the vehicle accelerated out of control and crashed into a guardrail. The air bags did not deploy; however, they ruptured and burst into smoke after approximately ten minutes without warning. Both…

  TL* the contact owned a 2013 mercedes-benz gl450. While driving approximately 5 mph in a parking lot, the vehicle accelerated out of control and crashed into a guardrail. The air bags did not deploy; however, they ruptured and burst into smoke after approximately ten minutes without warning. Both the driver and front passenger sustained injuries that required medical attention. The police and the paramedics were at the scene and a police report was filed. The vehicle was destroyed and towed to a tow yard. The manufacturer was not made aware of the failure. The failure mileage was 24,000. ...Updated 09/14/16 *bf *cn

• Jan 11, 2016WA36,000 mi
  Electrical system · Exterior lighting
  Driving down the freeway at 60 mph, a message was displayed on the instrument panel "blind spot assist inoperative," and the turn indicators stopped working, both left and right. Had to exit the freeway, but was not able to indicate to other drivers that I was changing lanes, as turn indicators…

  Driving down the freeway at 60 mph, a message was displayed on the instrument panel "blind spot assist inoperative," and the turn indicators stopped working, both left and right. Had to exit the freeway, but was not able to indicate to other drivers that I was changing lanes, as turn indicators were not working. Came to parking lot, shut the engine off and started back up, then the turn indicators started working along with blind spot assist. However, the issue came back after driving a few more miles. This problem also happened on the surface roads traveling at 35 mph.

• Jul 31, 2015PA37,000 mi
  Electrical system · Engine
  TL* the contact owns a 2012 (na) mercedes benz gl450. While driving at 40 mph through a puddle, the vehicle stalled without warning. The contact was able to merge to the side of the road, where the vehicle eventually turned off. The contact stated that the failure recurred intermittently. In…

  TL* the contact owns a 2012 (na) mercedes benz gl450. While driving at 40 mph through a puddle, the vehicle stalled without warning. The contact was able to merge to the side of the road, where the vehicle eventually turned off. The contact stated that the failure recurred intermittently. In addition, the vehicle failed to recognize the key and took several attempts to start the vehicle. The vehicle was taken to the dealer. The technician was unable to duplicate the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 37,000. ...Updated 09/28/15 *bf *cn

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
• 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
• 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11010750Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to FIN vehicle identification end number. If vehicle falls outside of FIN range, create a TIPS case. Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11008070Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to VIN vehicle identification end number. If vehicle falls outside of VIN range, create a TIPS case. Model series 192: xxx xxx xx 182881 Model series 232: xxx xxx xx 182883 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
• 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
• 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
• 10205814Fuel filler flap opens slowly/switch flashes/tank is bleeding instrument cluster warning
• 10205265Outside mirror fogged.
• 10205251Engine fan runs continuously, a/c inoperable or, engine light illuminates sporadically.
• 10205250Engine fan runs continuously, a/c inoperable or, engine light illuminates sporadically.
• 10205248"SOS mbrace service not activated".
• 10205247Traffic information service and posibly the voice control, nonfunctional after navigation software update.
• 10205236"Metadata loss- Please reimport all media data".
• 10205234Software update of COMAND Online control unit.
• 10205233Mobile phone cotacts are not transferred completely.
• 10205226High beams not functioning when first operated.
• 10205147Ticking or pulsing noise from high-pressure pump and/or fuel injectors.
• 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
• 10184799Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain Mercedes-Benz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or caused to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed.
• 10184797Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain Mercedes-Benz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or caused to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed.
• 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
• 10171637Retrofitted front door exit lamps with logo projection flicker
• 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
• 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
• 10167546FC 2783 (Friction power of torque converter lockup clutch is too high) or FC 0741 (Actuation of torque converter lockup clutch not possible) stored in transmission control unit. One possible additional customer complaint could be "poor acceleration" e.g. due to engine intervention. This can affect all NAT2FE+ (7G-TRONIC PLUS) vehicles with engines OM651, OM642LS and M278 in the production period from 04/2011 to 02/2012 and with more than 10,000 km. The two fault codes can also occur in combination with rpm sensor faults (see also GI27.50-P-035556). The rpm sensor fault is not connected with this complaint.
• 10167487Minor leaks at the oil duct of the left or right cylinder head of engines 157, 276 and 278. 1. Left cylinder head: Oil passage plug hole on left beside mechanical vacuum pump. 2. Right cylinder head: Oil passage plug hole below high-pressure pump housing.
• 10167040This Service Campaign has been initiated because Daimler AG (DAG), the manufacturer of Mercedes-Benz vehicles, has determined that the mbrace software does not correspond to current production configuration. An authorized Mercedes-Benz dealer will update the mbrace control module software at the next workshop visit.
• 10166988Collision Prevention Assist (CPA) may warn for no obvious reason (optical and/or acoustic warning message).
• 10166976Message in instrument cluster "DISTRONIC PLUSCurrently Unavailable - See Owner's Manual"

Every Mercedes-Benz GL450 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.