2020 Mercedes-Benz GLS 450
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › GLS 450 › 2020
These records cover every 2020 Mercedes-Benz GLS 450. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
22 recalls name the 2020 Mercedes-Benz GLS 450. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023-2024 GLE 350, 2020-2024 GLE 450, 2020-2023 GLS 580, GLE 580, 2019-2023 GLS 450, 2021-2023 Maybach GLS 600, AMG GLS 63, 2021-2024 AMG GLE 53, AMG GLE 53 Coupe, and AMG GLE 63 S vehicles. A 48-Volt ground connection under the passenger seat may not be secured properly, resulting in the ground…
Risk and remedy
Risk
An overheated ground connection can increase the risk of a fire.
Remedy
Dealers will inspect and tighten the 48-Volt ground connection as necessary, free of charge. Owner notification letters were mailed on May 3, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2024040002.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2023 GLE 450 and GLS 450 vehicles. The transmission may not fully downshift in certain conditions, causing the engine to stall.
Risk and remedy
Risk
An engine stall increases the risk of a crash.
Remedy
Dealers will update the transmission control unit software, free of charge. Owner notification letters were mailed March 29, 2024. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2021 GLE350, GLE450, GLS450, GLS580, 2021 AMG GLE53, AMG GLE63, Maybach GLS600, AMG GLS63, and 2020 GLE580 vehicles. The air conditioner drain hoses may have been incorrectly installed, causing water to drain into the passenger compartment.
Risk and remedy
Risk
Water intrusion into the foot wells may cause corrosion and/or short circuits to electrical components, increasing the risk of fire. In addition, the emergency call (eCall) feature may be disabled and the doors may not unlock, increasing the risk of injury. Also, the engine may not start or may enter a limp-home mode, increasing the risk of a crash.
Remedy
Dealers will inspect and reinstall the air conditioner drain hoses, as necessary, free of charge. Owner notification letters were mailed April 28, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of recall numbers 21V-288 and 19V-587. MBUSA's numbers for this recall are 2023030014 and 15.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 AMG GLS63, 2020-2022 GLS450 and GLS580 vehicles. Due to a manufacturing error, the locks on the third-row seatbacks may fail in the event of a crash.
Risk and remedy
Risk
A seat with a seatback lock failure may not properly restrain occupants, increasing the risk of injury during a crash.
Remedy
Dealers will inspect and replace the third-row seatback, as necessary, free of charge. Owner notification letters were mailed November 18, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022100011.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2022 GLE350, GLE450, GLS450, 2021-2022 AMG GLE53, 2020-2021 GLE580, GLS580, and 2021 GLE400e, AMG GLS63, AMG GLE63 S, and Maybach GLS600 vehicles. Due to a manufacturing error, the rear door window trim bars may detach.
Risk and remedy
Risk
Detached trim bars may cause a road hazard and increase the risk of a crash or injury.
Remedy
Dealers will inspect and secure the rear window trim bars, as necessary, free of charge. Owner notification letters were mailed November 1, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022090010.
Mercedes-Benz, LLC (MBUSA) is recalling certain 2020 Mercedes-Benz GLS 450 and GLS 580 vehicles. The front air bag wiring harness may be routed incorrectly, which can cause the air bag not to deploy properly. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."
Risk and remedy
Risk
An air bag that does not deploy properly can increase the risk of injury in the event of a crash.
Remedy
Dealers will correct the wiring harness routing, free of charge. Owners notification letters were mailed August 22, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022070006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2022 GLE450, GLS450, 2021-2022 AMG GLE53, 2020-2021 GLE580, GLS580, 2021 AMG GLE63, Maybach GLS600 and AMG GLS63 vehicles. A ground cable bolt for the 48V ground connection under the front passenger seat may not be secured properly, which can cause the electrical cable to overheat.
Risk and remedy
Risk
An overheated electrical cable can increase the risk of a fire.
Remedy
Dealers will inspect and tighten the ground cable bolt, as necessary, free of charge. Owner notification letters were mailed July 8, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022040017.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018-2021 CLA-Class, GLE/GLS-Class, A-Class, C-Class, E-Class, E-Class Coupe/Convertible, GLA/GLB-Class, GLC-Class, and CLS-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The rearview camera may not display the rearview image due to a software error. As such…
Risk and remedy
Risk
An inoperable rearview camera display reduces the driver's rear view, increasing the risk of a crash.
Remedy
Dealers will update the rearview camera software, free of charge. Owner notification letters were mailed July 15, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022060007.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019 AMG G63, C300, E300, G550, AMG GT63, AMG GT53, 2019-2020 A220, GLA250, GLC300, 2016 C300, 2020 AMG A35, AMG C43, AMG C63, CLA250, E350, E450, GLB250, GLE450, GLS450, GLS580, S560, and SL550 vehicles equipped with a gasoline engine. During the manufacturing process, particles may have been trapped…
Risk and remedy
Risk
A fuel leak in the presence of an ignition source, such as hot engine or exhaust components, can increase the risk of a fire.
Remedy
Dealers will replace the fuel rail and fuel injectors, free of charge. Owner notification letters were mailed April 22, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for the recall is 2022030003.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020 GLS450, GLS580, GLE350, GLE450, AMG C63, and 2021 AMG GLE53 vehicles. The seats may have been assembled incorrectly.
Risk and remedy
Risk
Incorrectly assembled seats may not properly restrain an occupant during a crash, increasing the risk of injury.
Remedy
Dealers will inspect and repair the seats, as necessary, free of charge. Owner notification letters are expected to be mailed December 8, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021110010.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2021 CLA-Class, GLE/GLS-Class, A-Class, E-Class, E-Class Coupe and Convertible, GLA/GLB-Class, GLC-Class, CLS-Class, and AMG GT-Class 4-door Coupe vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The MBUX multimedia system software may cause the display to remain…
Risk and remedy
Risk
A backup camera that displays a blank image reduces the driver's rear view, increasing the risk of a crash or injury.
Remedy
The multimedia system software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed beginning June 28, 2021. Owners may contact MBUSA customer service at 1-800-367-6373. MBUSA's number for this recall is 2021050012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 AMG GLE 53, 2020 GLE350, GLE450, GLE580, GLS450, and GLS580 vehicles. The air conditioner drain hoses may have been incorrectly installed, causing water to drain into the passenger compartment.
Risk and remedy
Risk
Water intrusion into the driver and passenger side foot wells may cause corrosion and/or short circuits to electrical components, increasing the risk of fire. In addition, the emergency call (eCall) feature may be disabled and the doors may not unlock, increasing the risk of injury. Also, the engine may not start or may enter a limp-home mode, increasing the risk of a crash.
Remedy
Dealers will inspect and correct the air conditioner drain hoses, as necessary, free of charge. Owner notification letters were mailed June 4, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021040024.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2021 GLE450, GLE350, and 2020 GLS450, GLE580, GLS580 vehicles. During certain evasive driving maneuvers, the Electronic Stability Program (ESP) software may apply torque to one of the front wheels, pulling the vehicle to one side. As such, these vehicles fail to comply with the requirements of…
Risk and remedy
Risk
If the vehicle unexpectedly pulls to one side during an evasive maneuver, it can increase the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will update the ESP software, free of charge. The recall began March 31, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021030004.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020 GLS 450, GLE 350, GLE 450, and 2021 AMG GLE53 vehicles. The dashboard surface may not be properly secured to the base material.
Risk and remedy
Risk
In the event of a crash where the passenger air bag deploys, an unsecured dashboard could impair the inflation of the passenger air bag, increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will replace the dashboard, free of charge. The recall began April 16, 2021. Owners may contact MBUSA customer serviced at 1-800-367-6372. MBUSA's number for this recall is 2021030003.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2020 GLE 350, GLE 450, GLE 580, GLS 450, GLS 580 vehicles equipped with an optional illuminated Mercedes-Benz star logo in the front grill. The star logo's electrical ground connection may not be installed properly, potentially affecting the function of other components that share the same ground…
Risk and remedy
Risk
If the power steering, wiper motor, or left headlight malfunction there could be an increased risk of a crash.
Remedy
MBUSA will notify owners, and dealers will relocate the ground connection, free of charge. The recall began November 13, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020100015/6.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2020 GLE450, GLS450, and GLS580 vehicles. The sealing of the piston assembly in the front struts and rear shock absorbers may leak and fail prematurely.
Risk and remedy
Risk
Premature wear of the front struts and rear shock absorbers can affect vehicle handling and control, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the front strut assemblies and rear shock absorbers, free of charge. The recall began October 20, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020090001.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2020 GLE350, GLE450 AND GLS450 vehicles. The seams on the rear crossmember may have been insufficiently welded. This may allow cracks to form when towing, possibly causing the rear crossmember to detach from the vehicle.
Risk and remedy
Risk
If the rear crossmember detaches from the vehicle, it can become a road hazard and increase the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the rear crossmember, free of charge. The recall began July 17, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020060013.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2020 CLA250, CLA250 4MATIC and CLA35 AMG 4MATIC, 2020-2021 GLE350, GLE350 4MATIC, GLE450 4MATIC, GLS450 4MATIC and GLS580 4MATIC and 2021 GLE53 AMG Coupe, GLE63S AMG 4MATIC, GLS63 AMG 4MATIC and Maybach GLS600 4MATIC vehicles. The instrument cluster software may deactivate the illumination of certain…
Risk and remedy
Risk
If the interior switches are not illuminated, they may be more difficult to find and operate, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will update the instrument cluster software, free of charge. The recall began March 31, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020030019.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2020 GLE350, GLE350 4MATIC, GLE450 4MATIC, GLS450 4MATIC, and GLS580 4MATIC vehicles. The rear door window trim may detach.
Risk and remedy
Risk
The detached trim can become a road hazard, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect and fasten the rear door window trim, as necessary, free of charge. The recall began November 8, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019100011.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2020 GLE350, GLE350 4MATIC, GLS450 4MATIC, and GLE450 4MATIC vehicles. The air conditioner drain hoses may have been incorrectly installed, causing water to drain from the air conditioner into the passenger compartment.
Risk and remedy
Risk
If a significant volume of water enters the driver and passenger side foot wells, it might cause corrosion and/or short circuits to the electrical components in the area, increasing the risk of fire. In addition, the emergency call (eCall) feature may be disabled; the vehicle may not be able to be unlocked and/or started; and the engine limp-home mode might be activated during driving. These features increase the risk of an injury or crash.
Remedy
MBUSA will notify owners, and dealers will inspect and correct the air conditioner drain hoses, as necessary, free of charge. The recall began September 6, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019080005.
Owner complaints
36 complaints3 involved a crash1 involved a fire3 injuries
What owners report most
Latest complaints
- Air bags · Electrical system · Visibility/wiper
AMENDMENT TO ACTIVE CASE 11723015. CRITICAL AIRBAG & SAFETY DEFECTS. This files a safety defect amendment to open case 11723015. Diagnostic scans confirm central data bus network collapse on VIN [XXX] has migrated into safety-critical occupant restraint and visibility modules, violating 49 U.S.C.…
AMENDMENT TO ACTIVE CASE 11723015. CRITICAL AIRBAG & SAFETY DEFECTS. This files a safety defect amendment to open case 11723015. Diagnostic scans confirm central data bus network collapse on VIN [XXX] has migrated into safety-critical occupant restraint and visibility modules, violating 49 U.S.C. § 30118. I. AIRBAG & RESTRAINT HAZARDS Scans from [XXX], document active faults: DTC U042782: "Implausible data received from Electronic Ignition Lock." The SRS module receives corrupted data from the failed ignition gateway, creating risk of airbag non-deployment. DTC B007A13: Passenger seatbelt pre-tensioner open circuit; occupants are unprotected against crash displacement. DTC B11FA4B: Active "Overtemperature" faults in heating elements indicate localized thermal short-circuit risk. II. HARDWARE DECAY Physical teardown confirmed structural oxidation on the central gateway motherboard and corroded connector pins. Modular swaps failed; network lock code U016887 returned within 8 months. Raw dealer records are available for federal inspection. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Structure
The contact owns a 2020 Mercedes Benz GLS. The contact stated that while driving on the highway, the rear door window trim bars on the passenger side detached from the window. The vehicle was taken to the dealer where they diagnosed as a rear door window trim detachment however the vehicle was not repaired. The manufacturer was not notified of the issue. The approximate failure mileage 65,000.
- Structure › Body · Unknown or other
Window trim on the passenger rear window fell off while driving- it put others at risk by flying off the vehicle on the interstate- Mercedes Benz of Omaha quoted replacement of the window trim parts- no warning messages on dash
- Electrical system · Engine · Fuel/propulsion system
The engine wiring harness insulation near the ignition coil connectors prematurely deteriorated due to prolonged exposure to engine heat in the turbocharger/exhaust area. Multiple wiring connectors exhibited brittle, cracked insulation with exposed conductors. The degraded wiring began shorting…
The engine wiring harness insulation near the ignition coil connectors prematurely deteriorated due to prolonged exposure to engine heat in the turbocharger/exhaust area. Multiple wiring connectors exhibited brittle, cracked insulation with exposed conductors. The degraded wiring began shorting within the ignition system, causing engine misfires, ignition circuit faults, and eventual loss of engine operation. While being operated by a rental customer the vehicle developed severe misfires followed by electrical shorting, smoke, localized flames in the engine harness area, and eventual engine shutdown. The flames self-extinguished after the electrical shorting stopped, but portions of the harness insulation showed thermal damage and overheating. The customer became stranded due to the vehicle becoming inoperable. Diagnostic faults included ignition coil circuit open faults and ignition primary circuit faults. The vehicle ultimately became inoperable due to the electrical failure. Inspection revealed multiple adjacent ignition harness connectors showing progressive heat-related insulation degradation in the same high-temperature area, indicating a broader harness material failure rather than isolated damage. This failure occurred on a 5-year-old vehicle. Engine wiring harness insulation should not prematurely degrade and short under normal operating conditions.
- Forward collision avoidance › Warnings
On a sunny afternoon without zero clouds in the sky, 75 degrees I was driving at 35 mph on a two-lane road with no cars in front of me, behind me, or coming in the other direction, the brakes were urgently and automatically applied and the seat belts dramatically tightened. The system showed a…
On a sunny afternoon without zero clouds in the sky, 75 degrees I was driving at 35 mph on a two-lane road with no cars in front of me, behind me, or coming in the other direction, the brakes were urgently and automatically applied and the seat belts dramatically tightened. The system showed a large red X on the screen. It was obvious the automated safety system mistakenly thought we were about to crash into something but there wasn't anything but smooth asphalt.
- Back over prevention › Sensing system › Camera · Electrical system · Forward collision avoidance › Warnings
The vehicle (2020 GLS 450) suffers from terminal infrastructure "Electronic Rot," resulting in a consistent Breach of FMVSS 111 (Rearview Visibility) and dangerous Automatic Emergency Braking hallucinations. On 03/08/2026, a routine car wash triggered multiple system failures, including "Camera…
The vehicle (2020 GLS 450) suffers from terminal infrastructure "Electronic Rot," resulting in a consistent Breach of FMVSS 111 (Rearview Visibility) and dangerous Automatic Emergency Braking hallucinations. On 03/08/2026, a routine car wash triggered multiple system failures, including "Camera View Restricted" and "Adaptive Highbeam Assist Currently Unavailable," proving the electrical architecture is compromised by minor moisture. This is a multi-dealer failure: the vehicle was sold as "Certified Pre-Owned" by Mercedes-Benz of Fredericksburg with undisclosed active "Special Procurement" status; a 200-day attempted EIS remediation at i.g. Burton failed to resolve the hazards; and the regular service center, Mercedes-Benz of Annapolis, has failed to remediate the ongoing "Electronic Rot." All parties are currently withholding machine-level XENTRY diagnostic sequences required to verify the vehicle's safety status.
- Electrical system · Engine
The vehicle is experiencing deterioration of the main engine wiring harness insulation, resulting in exposed wires contacting each other. This condition has caused intermittent check engine lights and electrical fault codes. The dealership has confirmed that the wiring insulation has degraded…
The vehicle is experiencing deterioration of the main engine wiring harness insulation, resulting in exposed wires contacting each other. This condition has caused intermittent check engine lights and electrical fault codes. The dealership has confirmed that the wiring insulation has degraded, allowing wires to contact each other. The issue appears related to material durability of the harness rather than external damage. The concern is that continued deterioration could result in: •Sudden engine misfire •Loss of power while driving •Engine stalling •Potential electrical short circuit An unexpected loss of engine power at highway speeds could increase the risk of a crash. The dealership indicated that similar harness insulation concerns have been observed on other M256-equipped vehicles. This appears to be a potential safety-related defect involving engine wiring insulation durability.
- Unknown or other
The sunroof spontaneously shattered while driving down the interstate. No other cars involved and no rocks or debris caused it. It was inspected and repaired at a Mercedes dealer, however, Mercedes refused to cover the repair under the pre-owned certified warranty. We had to file an insurance claim. In doing research, it appears this is a common and ongoing problem with various models of Mercedes.
- Electrical system
The vehicle, 2020 Mercedes-Benz GLS450, was being backed out of the garage when an electrical failure occurred causing the vehicle to malfunction. This was a major safety issue that caused the entire vehicle electrical control systems to fail as the vehicle would not turn-off. The vehicle…
The vehicle, 2020 Mercedes-Benz GLS450, was being backed out of the garage when an electrical failure occurred causing the vehicle to malfunction. This was a major safety issue that caused the entire vehicle electrical control systems to fail as the vehicle would not turn-off. The vehicle eventually turned-off and was not operational. It was towed to a local dealer where we were they discovered that a heating/cooling system hose caused moisture to enter the cab of the vehicle. The end result was major electrical damage to the vehicle control system of the vehicle. This vehicle is my wife's primary means of travel along with our 4 young children. Had this major malfunction occurred while on a highway going at high speeds a parish the thought of what could have happened to the safety of my wife and children. Per attached dealership bill, the dealership was not able to obtain coverage for this $4,255.15 repair bill. In addition, I did find other Mercedes-Benz GLS450 models who were recalled for this very safety issue where moisture in the cab resulted in major electrical control systems of the vehicle.
- Power train
On numerous occasions the transmission does not fully down shift to the next lower gear and then when I have to accelerate quickly it will drop down to the lower gear like it’s supposed to but won’t shift out to the next higher gear and when I let my foot off the accelerator the truck slows down…
On numerous occasions the transmission does not fully down shift to the next lower gear and then when I have to accelerate quickly it will drop down to the lower gear like it’s supposed to but won’t shift out to the next higher gear and when I let my foot off the accelerator the truck slows down quickly like applying the brakes which almost had me rear ended a few times and now the adaptive cruise control is malfunctioning
- Electrical system · Engine
I am writing to escalate an unresolved service issue with my 2020 Mercedes Benz GLS 450, VIN [XXX] . During a maintenance service on March 6, my trusted independent services shop for 25 years, Carrera Motors in San Mateo CA, identified that the electrical harness of my GLS 450 was significantly…
I am writing to escalate an unresolved service issue with my 2020 Mercedes Benz GLS 450, VIN [XXX] . During a maintenance service on March 6, my trusted independent services shop for 25 years, Carrera Motors in San Mateo CA, identified that the electrical harness of my GLS 450 was significantly damaged. The plastic casing around the wires had effectively disintegrated, exposing the wires directly to the engine. Carrera Motors indicated that this was a serious issue and does not normally occur with a 5 year old vehicle. They encouraged me to contact Mercedes directly. At the instruction of Carrera Motors, I contacted Mercedes customer care on March 10 and was issued a case number (#[XXX]) for the harness issue. She mentioned that someone would get back to me within 3 business days. Unfortunately, 3 days went by without a response. I called and left 3 messages over the next 2 days. Finally, MBUSA returned my call and instructed me to take the car to an authorized Mercedes dealer. At my own expense, I had the car towed from Carrera Motors to Autobahn Motors in Belmont CA on March 18. Mark Nissen at Autobahn was responsible for the service of my vehicle. He and his services team have verified that the electrical harness was seriously damaged and needs to be replaced at a cost of $5,009.99. Replacement is considered critical, and it’s been identified as a serious safety issue. This issue has not been resolved. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Engine
On a long road trip - about halfway on [XXX] - received an error message on 48v system malfunction - immediately called nearest Mercedes dealership (Richmond Va) to schedule a service - while on the line received an engine overheating pull over and shut it off message - at this point vehicle…
On a long road trip - about halfway on [XXX] - received an error message on 48v system malfunction - immediately called nearest Mercedes dealership (Richmond Va) to schedule a service - while on the line received an engine overheating pull over and shut it off message - at this point vehicle deaccelerated over riding my control of vehicle speed. Had to navigate from far left lane to right hand emergency lane at 40 mph - very dangerous maneuver as losing power. Vehicle was towed and received a 48v software update - software that deaccelerates the vehicle with no override for safety is a real problem INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Suspension
The shock absorbers have prematurely failed as other recalled 2020 GLS vehicles, but our VIN is not showing under the recall campaign 20V329000. Can our vehicle be included on this recall?
- Visibility/wiper
intermittent rear view camera inoperable when you shift from park to reverse. Doesnt come on even if you turn off and tune on the engine.
- Forward collision avoidance › Adaptive cruise control · Vehicle speed control
The adaptive cruise control feature of this vehicle on various highways [XXX] , [XXX] and the [XXX] ) and in various locations while traveling at highway speeds has mis-read speed limit signs and aggressively decelerated(I assume by using its regenerative braking) to as low as 35mph while traffic…
The adaptive cruise control feature of this vehicle on various highways [XXX] , [XXX] and the [XXX] ) and in various locations while traveling at highway speeds has mis-read speed limit signs and aggressively decelerated(I assume by using its regenerative braking) to as low as 35mph while traffic is moving at 65+mph. The dealership was unable to duplicate this issue. No faults are displayed to the driver. I do not know if rear brake lights are illuminated when this occurs. This is an aggressive and scary deceleration with no warning. I fear a rear end collision is likely. No one aside from the dealership has inspected this vehicle INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Forward collision avoidance › Adaptive cruise control
We intermittently experience phantom braking, including on the highway with no objects or vehicles ahead of us (for example, not on a curve, no vehicle visible within half a kilometer). Vehicle abruptly slows. This includes when in a lane (no lane change). It also can occur during a properly…
We intermittently experience phantom braking, including on the highway with no objects or vehicles ahead of us (for example, not on a curve, no vehicle visible within half a kilometer). Vehicle abruptly slows. This includes when in a lane (no lane change). It also can occur during a properly indicated lane change. It occurs when we are driving the posted limit. It also occurs when there are no parallel nearby roads. This appears to be a significant safety issue.
- Forward collision avoidance › Adaptive cruise control · Forward collision avoidance › Automatic emergency braking · Forward collision avoidance › Warnings
I have received multiple notifications over several months that read "Camera view restricted". This impacts the collision avoidance and adaptive highbeam assist functions. Dealer has offered no service recommendations.
- Electrical system
While driving on the New Jersey Turnpike on November 17, 2023, a burning smell was noticed inside the car. The smell lasted about an hour. No smoke was present and the car continued to operate. While concerned, I assumed it was environmental and outside the car. On November 25, 2023 my car…
While driving on the New Jersey Turnpike on November 17, 2023, a burning smell was noticed inside the car. The smell lasted about an hour. No smoke was present and the car continued to operate. While concerned, I assumed it was environmental and outside the car. On November 25, 2023 my car threw a 48V battery warning and forcibly shut off. We were not on a highway at the time and were able to pull over to a gas station. MB roadside was called and towed the car to Euro Motorcars Devon of Devon, PA, the local Mercedes-Benz dealer and where I purchased the car and receive service. Over the course of the next few weeks the service department concluded and ultimately determined that there were burnt out cables which were connected to the 48V battery (this is highlighted in the service receipt attached). This repair was not covered under my warranty and lead to a $5,804.56 repair bill. The car was repaired to my satisfaction and the bill was paid in full on December 14, 2023 determined the matter was complete. On or about May 1, I received a recall notice from MBUSA. The ID is 2024040002 and the NHTSA Recall ID is 24V207. This recall specifically called out the 48V battery connections and potential for misconnections to cause fire. This is the exact issue that is clearly articulated in the service report (attached). After six weeks attempting full reimbursement, MB considered the issue closed and their official position was that I was only entitled to $337.08 for the actual recall of the battery connection check. Of course the connections would now be correct as they fixed them and replaced the cables that caught fire. I am escalating this to your department and seek full reimbursement from Mercedes for this repair performed. This failure occurred prior to the recall notice and is the singular event that the recall is to mitigate that happened.
- Service brakes
The passenger rear wheel brake caliper lower bolt got loose. The bolt is most likely not available for inspection. The caliper body then started rubbing against the wheel inside surface and caused a noise. If the caliper body had jammed into the wheel and stopped it from rotating, say on the…
The passenger rear wheel brake caliper lower bolt got loose. The bolt is most likely not available for inspection. The caliper body then started rubbing against the wheel inside surface and caused a noise. If the caliper body had jammed into the wheel and stopped it from rotating, say on the highway, the vehicle could have skidded or rolled over? The MB dealership inspected and replaced the bolt. There were no warning lamps, messages or other symptoms of the problem prior to the failure. The noise came during braking on tuesday, 28 May. The car was repaired by the MB dealership on Thursday, 30 May.
- Back over prevention › Warnings · Forward collision avoidance › Automatic emergency braking · Service brakes
Today around 6:47pm. I was reversing my car and I noticed another car in my backup camera and tried shift the gear shift to drive but it didn't work and stayed stuck on reverse and would not moved and the brake pedal and emergency brake wouldn't work.
- Electrical system
The dashboard screen stops working randomly. This is not related to extreme outdoor temp conditions. Mercedes dealer could not reproduce the problem and therefore could not offer any solution. Problem has happened 5-6 times over the past 7 months. Please watch video below: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Electrical system
Vehicle would not start. 48v battery light came on. Waited 15 minutes, vehicle started, drove to dealership who did diagnosis. Battery replacement required $1800 + $1200 labor. 2020 vehicle with 61K miles. Bought certified vehicle from MBZ dealership, added a MBZ 3 year or 100K mile extended…
Vehicle would not start. 48v battery light came on. Waited 15 minutes, vehicle started, drove to dealership who did diagnosis. Battery replacement required $1800 + $1200 labor. 2020 vehicle with 61K miles. Bought certified vehicle from MBZ dealership, added a MBZ 3 year or 100K mile extended warranty but this battery is considered a wear and tear item not covered. That would be fine except for the fact that this battery issue is well known to MBZ as it has multiple reported instances of failure on vehicles with 6K to 60K miles.
- Electrical system
I have noticed a significant issue with the AC vent system of my Mercedes GLS 450. The vents seem to be distributing mold smell already took my vehicle multiple times to park place Mercedes in Dallas and they performed service but the issue is persistent. I have taken the vehicle to my local…
I have noticed a significant issue with the AC vent system of my Mercedes GLS 450. The vents seem to be distributing mold smell already took my vehicle multiple times to park place Mercedes in Dallas and they performed service but the issue is persistent. I have taken the vehicle to my local Mercedes service center, where they attempted to address the issue. However, despite their efforts, the problem has persisted. This defect is impacting not only the comfort of my driving experience but also the overall value and performance of the vehicle. We had GLE in my family that had the same issue we took it to Park Place and complained about this many times and end up selling the vehicle as they never resolved the issue. Vehicle: 2017 MERCEDES-BENZ GLE350 VIN: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Air bags · Forward collision avoidance › Automatic emergency braking · Unknown or other
03/17/2023 driving on US1 coming up to speed after pulling onto highway after cars passed I went 0.2 miles and was looking at my driver side mirror ( no traffic on road ahead of me) when I hit something that pushed my big SUV toward oncoming traffic. I held wheel and muscled car to side of road…
03/17/2023 driving on US1 coming up to speed after pulling onto highway after cars passed I went 0.2 miles and was looking at my driver side mirror ( no traffic on road ahead of me) when I hit something that pushed my big SUV toward oncoming traffic. I held wheel and muscled car to side of road stopping short of a telephone pole. Car was upright I had trouble loosening seat belt while my wife was hanging forward into hers. Dog harnessed in back seat was ok Got out of car to see a car hauler 30? Footer sticking about 4 feet into the road and travel lane. Investigation by police revealed truck driver backed out of a company driveway into the road with no people helping. With traffic totaled right front tearing wheel off. No air bags deployed, I do not believe accident avoidance nor auto braking employed, MB safety and accident location didn’t activate and not sure passenger seat belt pre tightened. Police report Saco Maine 23-113-AC . MBUSA notified. Car held for them to examine. 4 weeks later have heard nothing other than “ we’re working on it”police and Insurance found 0 fault for me. Car totaled for repair cost
- Electrical system · Engine · Power train
This incident occurred around 5:50pm on Wednesday, September 21, 2022. I was driving on a merge connector between two freeways in San Francisco at about 60mph, when the vehicle threw a series of error codes and warnings on its displays, culminating with “shut down engine immediately”. The first…
This incident occurred around 5:50pm on Wednesday, September 21, 2022. I was driving on a merge connector between two freeways in San Francisco at about 60mph, when the vehicle threw a series of error codes and warnings on its displays, culminating with “shut down engine immediately”. The first error was a 48V battery system charging failure, and the second was a warning that coolant was too hot. The instrument panel and steering and brakes did not lose power, but the accelerator no longer worked, and the vehicle slowed down to about 35mph. I had to merge across 4-5 lanes of rush hour traffic at this speed (sketchy) to make it to the side of the freeway, and was able to exit safely and stop in a safe spot. Upon turning off the vehicle for a few minutes and then restarting it, a generic check engine light remained on afterwards. I had the vehicle towed to a Mercedes dealer where the fault(s) are currently being diagnosed. According to the dealer, they are in touch with MBUSA Engineering due to the nature of the fault codes. The vehicle had recently undergone a 50,000 mile routine service without any problems being flagged. The safety implications of this incident are clear: with no ability to match the speed of the flow of traffic, I could have been rear-ended or involved in a collision as I limped across the freeway to safety. I am fortunate that the vehicle had enough residual kinetic energy that I didn’t end up stuck blocking a freeway lane in rush hour traffic. Searching online for similar issues, this appears to be a known manufacturing issue with the mild hybrid inline-6 engine in this model of vehicle. For instance, all of the top Google hits for the term “GLS 48V battery failure” yield relevant and similar reports from other drivers, including summaries from consumer lawyers like this one: https://lemberglaw.com/mercedes-benz-gle-battery-electric-problems/
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010744Complaint Engine cooling fan running for an extended time after switching off vehicle. Cause Optimized thermal management in latest PTCU software. Remedy This is a normal function in the latest PTCU software. Engine fan will operate for up to 20 minutes after ignition is switched off. Note: Repair work should only be performed if a clear malfunction is identified
- 11010652Complaint One or more of the seats in the second or third row cannot be folded over when the switch group in the trunk is used. Cause Under analysis. Remedy Please thoroughly check the physical layer such as operating switches, lines, and pins to make sure that they are not the reason for the fault. Verify the switches are showing correct actual values with the Xentry. Verify the seats fold properly when using other switches. After this, create a TIPS case and attach a control unit log for the corresponding control unit along with a CAN trace from the body CAN that documents the problem.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11010450Complaint When using the offroad display in the MBUX, the "Transparent hood" function cannot be activated using the camera symbol. Cause MBUX FUP5 software: E504.3 (A 297 904 97 00) E504.4 (A 297 904 03 01) Remedy Update of head unit A26/17 to the new software: E504.5 (A 297 904 09 01)
- 11010438Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 01.06.2023 (Send to Body/Chassis/Entertainment Inbox) - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 01.06.2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11010437Complaint Automatic window raising function of side window inoperative. Cause Denormalization of the window lifter system. Remedy Update the software in the affected door control unit (N69/x). This requires the door control unit (N69/x) to be commissioned. (Path: XENTRY -> Control units view -> DCU-XX (N69/x) -> Adaptations -> Commissioning) SW item numbers of the repair software: A1679023716 for the door control units on the front doors (N69/1 and N69/2) A1679023816 for the door control units on the rear doors (N69/3 and N69/4)
- 11009550Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : Remedy 1 (Only applies to vehicles produced during or prior to June 2023) 1. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 2. Clear picture of VIN on B-pillar. 3. Ensure that the rest of the AC system has been thoroughly checked for leaks before condemning the evaporator. Remedy 2 (Applies to all 167's produced after June 2023) 1. Do NOT remove the expansion valve from the evaporator prior to being advised to in a TIPS case. 2. Initial Quick Test 3. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 4. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 5. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 6. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 7. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 8. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 9. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments.
- 11009549Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 6/1/2023 - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 6/1/2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008882Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : Remedy 1 (Only applies to vehicles produced during or prior to June 2023) 1. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 2. Clear picture of VIN on B-pillar. 3. Ensure that the rest of the AC system has been thoroughly checked for leaks before condemning the evaporator. Remedy 2 (Applies to all 167's produced after June 2023) 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. Please see the list of WIS documents for forming gas leak check and recharging of the system. All documents, with the exception of videos need to be uploaded for the warranty claim. Videos are only needed if a TIPS case is opened. Ensure that a full vacuum is pulled on the system for at least 30 minutes after replacement Condenser replacement is NOT authorized as a suitable repair in lieu of the dryer not being available.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008093Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007972Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation.
- 11007969Complaint When using the offroad display in the MBUX, the "Transparent hood" function cannot be activated using the camera symbol. Cause MBUX FUP5 software: E504.3 (A 297 904 97 00) E504.4 (A 297 904 03 01) Remedy The remedy is currently being developed.
- 11007857Complaint Customer concern of Air Conditioning not cooling. Note: For vehicles produced during or prior to June 2023, a TIPS case is not necessary. However, parts from repairs on such vehicles may be requested back for analysis at the QEC. Therefore, please follow parts disposition in NetStar. Repairs where parts are not returned per parts disposition instructions, or parts found to be NTF (no trouble found) are subject to debit. ALL steps, with the exception of videos, should be documented and uploaded with the claim submission. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. "NO TIPS case needed on vehicles during or prior to June 2023"
- 11007796Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11007673Complaint Damage or discoloration to paint protection films on vehicle. Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.
- 11006678Complaint Head-up display permanently or sporadically unavailable - with warning message in driver display Head-up display permanently or sporadically unavailable - without warning message in driver display Display permanently or sporadically discolored and out of focus Cause Previous N133/1 - Instrument cluster (IC) control unit software. Remedy Update the N133/1 - Instrument cluster (IC) software.
- 11006550Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. If the vehicle is produced AFTER June 2023, a TIPS case is required for replacement. Please open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. 9. For vehicles produced during or prior to June 2023, a TIPS is not necessary. However, parts from repairs on such vehicles may be requested back for analysis at the QEC. Therefore, please follow parts disposition in NetStar. Repairs where parts are not returned per parts disposition instructions, or parts found to be NTF (no trouble found) are subject to debit. NOTE: Please see the list of WIS documents for forming gas leak check and recharging of the system. All documents, with the exception of videos need to be uploaded for the warranty claim. Videos are only needed if a TIPS case is opened. Ensure that a full vacuum is pulled on the system for at least 30 minutes after replacement Condenser replacement is NOT authorized as a suitable repair in lieu of the dryer not being available.
- 11005347Complaint Yellow coolant warning system message appears in instrument cluster. Fault code P048392 or P048397 present in N127 Powertrain Control Unit. Cause Faulty communication between fan and control unit N127-PTCU. Remedy If other fault codes related to engine fan are present, process these first. Replace engine fan with part as specified in XENTRY parts information. Group 50/015. Note: Do not install a lower wattage fan than what was originally installed in vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005334Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11003791The vehicles were visible and flagged in VMI as OPEN on January 14, 2022. Unrepaired affected vehicles will be shown as Closed-NA in VMI on June 17, 2024.
- 11003211Complaint The following event codes are logged in control unit IDC213 - N62/4 (Intelligent Drive control unit): U0401FC and U0401FD. Cause Under analysis. Remedy Neither of the two event codes is relevant for the functioning of control unit IDC213 - N62/4 (Intelligent Drive control unit) and can be ignored.
- 11003094Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. If the vehicle is produced AFTER June 2023, a TIPS case is required for replacement. Please open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. 9. For vehicles produced during or prior to June 2023, a TIPS is not necessary. However, parts from repairs on such vehicles may be requested back for analysis at the QEC. Therefore, please follow parts disposition in NetStar. Repairs where parts are not returned per parts disposition instructions, or parts found to be NTF (no trouble found) are subject to debit. NOTE: Please see the list of WIS documents for forming gas leak check, AC flushing and recharging of the system. All documents, with the exception of videos need to be uploaded for the warranty claim. Videos are only needed if a TIPS case is opened. The dryer must be replaced when there is a leak in the AC system.
- 11003092Complaint Seats cannot be adjusted Seats cannot be folded Seats in the 2nd seat row cannot be locked or unlocked Normalization cannot be performed in its entirety using XENTRY Cause Various Remedy *Make sure a battery charger is connected to vehicle while performing all testing* Please perform the following checks that help to resolve most concerns: #1 - Make sure seat control units have latest software installed on them. #2 - For seat folding concerns, pay careful attention to the lock mechanism and ensure it is fully releasing. If the locking mechanism is short-stroking, please replace associated Bowden cables. #2a - Seat folding concerns can also be related to binding of the seat frame. To remedy, loosen torque off bolts holding seat frame to car. Shift seat frame and ensure there is no binding. Re-torque bolts securing seat frame to car and re-test. #2b - For 3rd row seats, you can remove the backrest cushion to expose the folding latch motor/mechanism. If the springs are loose/not-captured, then you must replace this assembly. If the assembly is not available by itself, the seat frame must be replaced (as the assembly is included in new one). #3 - For seats showing unlocked in the IC when fully locked, please check seat frame carefully for small microswitches that can be damaged. #4 - For seats moving forward but not folding upward (2nd row), please ensure the 4 small clips are still located on the inner and outer rails of the seat. If they are broken (example being passenger kicking them), the seat will not fold up.
- 11000618Customer concern of Air Conditioning not cooling. Possible refrigerant leak at the evaporator. Remedy Perform the following measures and open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" In the case, please include the following: 1. Attach the Initial Quick Test 2. Short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (s 5. Video recording of the leak being found via sniffer and location. Note - Please see the list of WIS documents for forming gas leak check, AC flushing and recharging of the system. The dryer must be replaced when there is a leak in the AC system.
- 11000606Complaint Message in Instrument Cluster: "Active Brake Assist function restricted". The driver assistance systems are temporarily unavailable. Note: Please note the listed fault code! Cause Rarely, it may be the case that communication is interrupted due to a brief interruption in the power supply to the LRR (B92/12) or A108 (Active Brake Assist). Remedy Perform new SCN coding at BC_R (N10/8).
- 11000597Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures and open a TIPS case labeled "167 Evaporator Suspected of Leaking" In the case, please include the following: 1. Attach the Initial Quick Test 2. Short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (s 5. Video recording of the leak being found via sniffer and location. Note - Please see the list of WIS documents for forming gas leak check, AC flushing and recharging of the system. The dryer must be replaced when there is a leak in the AC system.
- 11000542High-frequency interference noise may be heard from the speakers while driving. This complaint only occurs when "voice amplification" is active. Coupling noise of microphone signal in voice amplification. Intermediate remedy: The interference noise can be remedied by deactivating voice amplification: "Home" -> "Settings" -> "System" -> "Audio" and de-select "Voice amplification to rear" to switch off the function (see attachment). Note: To activate or deactivate the function, the ignition must be switched on, seat belts (at rear and front) must be fitted and the doors, windows and roof must be closed. Permanent solution: Perform software update of MBUX multimedia system (A26/17) to E419.5 (available from 06/19) or greater. Deactivate the voice amplification feature. Inform customer of function and effects of additional sounds caused by driving over bumps or uneven road surfaces.
- 11000523Work procedure 1. Connect XENTRY Diagnosis. 2. Update left rear seat control unit software. - To do this, select menu item "Quick test view N32/5 Left rear electrical seat adjustment Adaptations Update of control unit software". - Then follow the user guidance in XENTRY Diagnosis. 3. Update right rear seat control unit software. - To do this, select menu item "Quick test view N32/6 Right rear electrical seat adjustment Adaptations Update of control unit software". - Then follow the user guidance in XENTRY Diagnosis. 4. Disconnect XENTRY Diagnosis.
Every Mercedes-Benz GLS 450 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.