2022 Mercedes-Benz Sprinter 1500
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › Sprinter 1500 › 2022
These records cover every 2022 Mercedes-Benz Sprinter 1500. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2022 Mercedes-Benz Sprinter 1500. Newest first.
Daimler Vans USA, LLC (DVUSA) is recalling certain 2019-2022 Mercedes-Benz Sprinter vehicles. The instrument cluster illumination may not be adjustable and appear too bright in certain lighting conditions. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 101, "Controls and Displays."
Risk and remedy
Risk
A display that is too bright can make it difficult for the driver to see critical safety information, increasing the risk of a crash.
Remedy
Dealers will update the instrument cluster software, free of charge. Owner notification letters were mailed January 31, 2025. Owners may contact DVUSA customer service at 1-877-762-8267. DVUSA's number for this recall is VS3BELKOM.
Daimler Vans USA, LLC (DVUSA) is recalling certain 2019-2023 Mercedes-Benz Sprinter and 2019-2021 Freightliner Sprinter vehicles. The partition wall may be missing bolts, allowing the wall to detach during a crash.
Risk and remedy
Risk
A detached partition wall can increase the risk of injury.
Remedy
Dealers will inspect and secure the partition wall as necessary, free of charge. Owner notification letters are expected to be mailed February 16, 2024. Owners may contact DVUSA customer service at 1-877-762-8267. DVUSA's number for this recall is VS3TREWAN.
Daimler Vans USA, LLC (DVUSA) is recalling certain 2021-2023 Mercedes-Benz Sprinter and 2021 Freightliner Sprinter vehicles. The topcoat paint formula may cause the windows and interior lashing rails to be insufficiently bonded to the vehicle.
Risk and remedy
Risk
An insufficiently bonded window can detach during a crash, and objects secured to an insufficiently bonded interior lashing rail can detach, increasing the risk of injury.
Remedy
Dealers will inspect the paint adhesion and repair it as necessary, free of charge. Depending on the extent of any damage, DVUSA may offer to repurchase the vehicle. Interim notification letters, notifying owners of the safety risk, were mailed February 5, 2024. Owner notification letters were mailed November 4, 2024. Owners may contact DVUSA customer service at 1-877-762-8267. DVUSA's number for this recall is VS3LACKHA.
Daimler Vans USA, LLC (DVUSA) is recalling certain 2021 Freightliner Sprinter and 2021-2023 Mercedes-Benz Sprinter and Metris vehicles. The fuel pump may shutdown, which can result in a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed November 1, 2023. Owners may contact DVUSA customer service at 1-877-762-8267. DVUSA's number for this recall is 4790205.
Daimler Vans USA, LLC (DVUSA) is recalling certain 2019-2022 Mercedes-Benz Sprinter and 2019-2021 Freightliner Sprinter vehicles. The instrument cluster may fail to display any information when the vehicle is started.
Risk and remedy
Risk
A blank instrument panel will not show critical information, such as vehicle speed, fuel gauge, warning messages, and warning lights, increasing the risk of a crash.
Remedy
Dealers will update the instrument cluster software on the affected vehicles, free of charge. Owner notification letters were mailed May 5, 2023. Owners may contact DVUSA customer service at 1-877-762-8267. DVUSA's number for this recall is VS3KOMBAUS.
Daimler Vans USA, LLC (DVUSA) is recalling certain 2022 Mercedes-Benz Sprinter vehicles equipped with electrically adjustable front swivel-seats. The wiring harnesses for the swivel-seats may have been incorrectly installed and may become damaged, which can cause the front side air bags not to deploy as intended.
Risk and remedy
Risk
An air bag that does not deploy as intended increases the risk of injury in a crash.
Remedy
Dealers will inspect and reattach the wiring harnesses, as necessary, free of charge. Owner notification letters were mailed March 17, 2023. Owners may contact DVUSA customer service at 1-877-762-8267. DVUSA's number for this recall is 5491810.
Daimler Vans USA, LLC (DVUSA) is recalling certain 2019-2022 Mercedes-Benz Sprinter and Freightliner Sprinter vehicles equipped with a manual parking brake and 7-speed automatic transmission. The guide bushing on the parking pawl may fatigue, which can cause the parking pawl not to engage and result in vehicle rollaway.
Risk and remedy
Risk
Vehicle rollaway increases the risk of a crash.
Remedy
Dealers will update the software of the electronic stability, transmission control, direct select module, and electronic ignition switch control units, free of charge. Owner notification letters were mailed February 10, 2023. Owners may contact DVUSA customer service at 1-877-762-8267. DVUSA's numbers for this recall are 22V2790611, 22V2790612, and 22V2790613.
Owner complaints
1 complaints
Latest complaints
- Tires › Bead · Tires › Markings · Tires › Tread/belt
The component that has failed has been the tread wearing out and as well as the 'layers' of the tire literally started to peel almost the size of a quarter. I am extremely uncomfortable to drive on the highway, knowing these tires are this early on starting to fall apart. The problem was confirmed…
The component that has failed has been the tread wearing out and as well as the 'layers' of the tire literally started to peel almost the size of a quarter. I am extremely uncomfortable to drive on the highway, knowing these tires are this early on starting to fall apart. The problem was confirmed by a dealer however neither the dealer or KUMHO wants to accept responsibility. These specific tires are meant for 6 years or 70k miles and this problem started around 29k miles. There were no warning lamps/ they have not been inspected by anyone as they claim it is not their problem, however last time I checked that is what warranties are meant for. I am displeased by the tires and will not pay for new ones knowing that these are prematurely falling apart.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11011223SMOG/Emissions Test fail due to one or more Readiness Monitors not set Complaint: The vehicle has failed the State Emissions Certification because one or more of the OBDII readiness monitors are not completely set. Cause: One or more of the following Readiness Monitors are not fully set within XENTRY: Misfire Monitoring - Injection System Fuel System Monitoring - Injection System, Fuel System, EGR Valve, O2 Sensor NMHC Catalyst Monitoring - NMHC/Diesel Oxidation Catalyst NOx Aftertreatment Monitoring - SCR Catalyst System Boost Pressure System Monitoring - Turbocharger, Charge Air System Exhaust Gas Sensor Monitoring - O2 Sensor, NOx Sensors Diesel Particulate Filter Monitoring - Diesel Particulate Filter System Exhaust Gas Recirculation System Monitoring - EGR Valve and system Remedy: Please complete the required driving conditions to fully set the incomplete Readiness Monitor. DO NOT: - Erase any fault codes. If fault codes are present, process these and allow the readiness drives to clear fault codes. - Flash or SCN code the CDI or SCR control units. - Perform a manual DPF regeneration, unless instructed below. - Disconnect the main battery.
- 11009856Complaint: Check engine light with fault code: P300E3B the efficiency of component 'SCR catalytic converter' is not sufficient, is present in the CDI control unit CDI (N3/28). Cause: This subject is currently being analyzed for all 907s equipped with the OM642 engine. Follow the instructions related to this subject to collect information about your vehicle. After completing the checks, please open a TIPS case and at-tach the collected information.
- 11009854Complaint: Noises when reversing slowly <5 km/h (squeaking) Cause: There is a seal in the electric drivetrain that seals off the coolant system from the electric motor. This seal is moistened with coolant during forward travel. As a result of the change in rotational direction when reversing slowly, it may be the case that this sealing ring is no longer moistened. Squeaking noises may occur as a result of the so-called "stick-slip effect". This behavior does not impact the function or durability of the sealing ring and electric drivetrain. Remedy: Do not replace any parts. Explain the cause of the noises to the customer.
- 11008717Complaint Check engine light with fault code: P300E3B the efficiency of component 'SCR catalytic converter' is not sufficient, is present in the CDI control unit CDI (N3/28). Cause This subject is currently being analyzed for all 907s equipped with the OM642 engine. Follow the instructions related to this subject to collect information about your vehicle. After completing the checks, please open a TIPS case and attach the collected information. Remedy Please complete the following inspections and tests: 1. Perform a tailpipe wipe test and document the results along with photographs. 2. Inspect the NOx connectors, pins, crimps, and harnesses between N37/7 and N37/8 to F152f59, Z7108, W105/3, and X30/81. 3. Provide actual values/sensor plausibility test results for all pressure and temperature sensors with the engine com- pletely cooled off for at least eight hours, the key on, and the engine off. Repeat the test with the engine/exhaust at operating temperature and the engine idling. 4. Perform a pressurized smoke test of the intake, charge air system, and exhaust to verify that there are no leaks. Apply overpressure (not exceeding 26 psi) from the exhaust pipe end and seal the system at the clean airline toward the air filter housing. Manipulate all components during the smoke test. 5. Provide diesel particulate filter actual values and regeneration history. 6. Inspect the SCR temperature sensor wirings and pins for electrical and physical correctness. Determine whether this sensor reaches operating temperature while driving and document the time it takes to reach operating temperatu- re. 7. Inspect the Adblue injector nozzle/s for clogging or leaking, and provide photographs. 8. With the Adblue injector/s removed from the exhaust system, perform two to three Adblue pressure tests and check for leaks. If leaks are detected, provide photographs. 9. Collect an Adblue sample, test fluid quality, and provide notes on its condition and quantity (color, clarity, separati- on, odor, etc.), along with a photograph for review. Also, provide a photograph of the spray pattern. 10. Separate the exhaust pipe downstream of the diesel particulate filter, inspect the diesel particulate filter and SCR, and note any soot, blockage, or damage. Provide photographs. 11. Inspect the SCR catalyst interior for dried Adblue residue, and provide photographs. 12. Perform several test drives at varying speeds to gather graphical illustrations (screenshots of the completed graphs in PDF format) of signals from NOx sensors. Provide three to four graphs or actual values of operational NOx sensors with XENTRY; see attachments for examples. Additionally, provide one graph/screenshot of the vehicle idling at operating temperature. Disconnect the Adblue injection valve, drive for approximately 30 minutes to exhaust all Ad- blue within the SCR catalytic converter, and provide two to three additional NOx graphs/screenshots with the sensor disconnected. (see attachments for needed graphs)
- 11005575Complaint T57 Electric step inoperative with warning on cluster. Cause Possible damage to end position sensors.
- 11005574Complaint Front door collides with fender. Cause Excessive dynamic stress results in permanent deformation of the lower hinge and causes the front door to collide with the fender. This can result in damage to the door holder and the front door at the threaded connection of the door holder.
- 11005573Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes PDF document in attachments. Complaint C: One or more electrical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of electrical fault codes PDF document attached. NOTE: This LI supersedes LI14.20-N-073813, which is no longer valid. Cause Cause of Complaint A: Increased friction between the EGR Valve blade and seat due to soot deposits causing a delay of the EGR Valve being able to reach the target value of the EGR Valve position controller. NOTE: This causes the EGR Valve blade and potentially the boost pressure controller to oscillate. Cause of Complaint B: Soot deposits between the EGR Valve blade and seat leading to the EGR Valve no longer being able to meet the desired target of the EGR Valve position controller. Cause of Complaint C: Internal EGR Valve or other electrical faults related to the EGR Valve function.
- 11003187Mercedes-Benz AG, the manufacturer of Mercedes-Benz Vans, has determined that on certain Sprinter and Metris vehicles, the B-pillar certification label might not contain information on the vehicle's rim size, tire size, and cold tire inflation pressure required under FMVSS 110 or, as applicable, FMVSS 120. In this case, relevant regulatory requirements might not be met. Mercedes-Benz believes this issue has no impact on vehicle safety. Mercedes-Benz intends to submit a petition to NHTSA for exemption from the notification and remedy requirements of 49 U.S.C. chapter 301, pursuant to 49 CFR Part 556, on the basis that this non-compliance is inconsequential as it relates to motor vehicle safety. MBUSA will conduct a service campaign to remedy new vehicles in dealer inventory. An authorized Mercedes-Benz dealer will replace the Certification Label on the affected vehicles.
- 11001110Complaint: Front door collides with fender. Excessive dynamic stress results in permanent deformation of the lower hinge and causes the front door to collide with the fender. This can result in damage to the door holder and the front door at the threaded connection of the door holder. Remedy: 1. In the event of damage to be claimed under warranty, please follow warranty guidelines 10.11.1 (see note) 2. Damaged body components will need to be repaired or replaced by a MB certified collision center. While at the collision center, please request a visual check for cracks on threaded connection of door holder in front door. 3. Replace lower hinge of front door on affected side of vehicle. (lower hinge will need to be painted) 4. Replace door holder (on both sides) with modified, shortened door holder. 5. For a repeat failure on a vehicle that has been previously repaired with the updated parts, Please create a PTSS case.
- 10253244Propeller Shaft Check Strap on the crossmember may not have been installed.
- 10251090Check Par????on Wall Bolts
- 10251085Check patrition Wall Bolts
- 10249333Mercedes-Benz AG, the manufacturer of Sprinter vehicles, has determined that on certain Sprinter (907 platform) vehicles, the chemical composition of the topcoat paint might not meet specifications. In such case, adhesion of the fixed windows to the vehicle body might be impaired. As a result, a loosening or detachment of the windows cannot be ruled out over the vehicle's lifetime, which could increase the risk of injury in the event of a crash. In addition, loosening of secured objects cannot be ruled out for vehicles with lashing rails, which could increase the risk of injury for vehicle occupants.
- 10249332Mercedes-Benz AG, the manufacturer of Sprinter vehicles, has determined that on certain Sprinter (907 platform) vehicles, the chemical composition of the topcoat paint might not meet specifications. In such case, adhesion of the fixed windows to the vehicle body might be impaired. As a result, a loosening or detachment of the windows cannot be ruled out over the vehicle's lifetime, which could increase the risk of injury in the event of a crash. In addition, loosening of secured objects cannot be ruled out for vehicles with lashing rails, which could increase the risk of injury for vehicle occupants.
- 10246043Please see the atached documents related to the campaign listed above.
- 10246041Please see the atached documents related to the campaign listed above.
- 10241385Replace Fuel Delivery Module.
- 10240168Various concerns in relation to electric power steering including Rattling/humming noise from electric power steering when steering fully turned (see video recordings 01 and 02).
- 10235072Software Updates.
- 10235071Software Updates.
- 10235070Software Updates.
- 10235069Software Updates.
- 10235068Software Updates.
- 10235067Software Updates.
- 10234058Swivel Seat Wire Harness Routing
- 10233790Complaint Noise in front door from window regulator when driving. Cause Loosened nut of window lifter leads to screw connection at bottom of door breaking the mounting point in the door (see attached picture). Remedy Glue in repair panel A 910 722 33 00 and screw in again with collar nut A 005 990 64 50. When using the adhesive, observe the following: Roughen the bonding surfaces slightly and clean them so that they are free of grease in order to guarantee secure bonding.
- 10233787Complaint Vehicles with SCR Generation 4: SCR/AdBlue warning message cannot be reset. Information: All fault codes in AdBlue (SCR) control unit have been processed and rectified; however fault code P13DF00 remains active and stored in the AdBlue (SCR) control unit. Cause The procedure for resetting the SCR/AdBlue warning message with XENTRY Diagnosis has not been carried out. Information: In order to reset the SCR/AdBlue warning message for SCR Generation 4, the AdBlue system needs to be checked. Remedy Follow Diagnostic Instructions
- 10232555Update Software - Comfort Function
- 10232325Complaint Check engine warning light active. Fault code P300CA8 or P300CA9 "Hot film mass air flow sensor malfunction" is present in engine control unit. Cause a) In the case of fault P300CA8: Due to incorrectly installed component parts of the clean air line between the air filter box and the exhaust gas turbocharger, it is possible that leaks may occur in the system which subsequently result in air mass faults A fouled air filter or leaks in the intake or charge air system downstream of the exhaust gas turbocharger may also cause these faults. b) In the case of fault P300CA9: Computational model for programmed values of air intake, in particular, for the high load mode, calculates this high load correction programmed value incorrectly. This leads to the programmed value drifting too quickly towards the limit. Remedy Install the following add-ons: 18937 for XENTRY 12/2020 18938 for XENTRY 03/2021
- 10232323Complaint MIL illuminated. Fault codes for 'position sensor of crankshaft' in combination with fault codes for 'Output stage fuel injectors' are set in the CDI control unit.
- 10232322Complaint Engine runs irregularly and it shakes. Indicator lamp lights up. Information: Fault codes for injectors and/or combustion misfires may be stored in the CDI control unit: On engine 642 cylinder 6 is affected. On engine 651 cylinder 2 is affected. Cause Charge air from the exhaust gas recirculation is condensed after being introduced into the charge air section. Information: Under certain operating conditions, condensation that has collected in the charge air cooler can enter the combustion chamber to a damaging degree and a damage profile is then generated (connecting rod bent). Remedy Perform following testing and diagnosis operations
- 10231020Complaint Various issues including control unit programming procedure will not complete successfully/no newer software found, communication faults, or sporadic malfunction of systems. Cause Aftermarket CAN device could be installed into the vehicle's CAN network. Such devices can be but are not limited to, remote start modules, CAN blockers, or high idle modules. Remedy A successful control unit programming session cannot be ensured while aftermarket devices are connected to the vehicle's CAN network. Some of the device companies supply a bypass to allow control unit programming.
- 10228818Complaint Various customer concerns of Climate Control system operating inadequately. Cause Stepper motor linkage in the heater case may cause a mechanical fault during actuation during unfavorable environmental conditions. NOTE: If the vehicle is equipped with H13 (rear additional heat exchanger), There is an additional stepper motor in the rear heater case under the vehicle. This stepper motor can influence the normalization process. May include fault code: B1A9C07 the output for control valve "Left water valve" has a malfunction. There is a mechanical fault. The component is called N29/12 (rear additional heat exchanger ) . Remedy: See instructions
- 10228812Complaint Distronic and/or Active Brake Assist inoperative after driving for an extended period Cause Blindness detection of the radar sensor. When driving for extended periods in areas with few or no objects for the radar sensor to detect, the radar sensor switches off due to the self-test and sets fault code C174AFB - The adjustment of the 'Active Brake Assist' control unit has malfunctioned. Remedy Check the area of the front radar for damage. Check whether fault code "C174AFB - The adjustment of the 'Active Brake Assist' control unit has malfunctioned" is set in the B92 or B92/1 Active Brake Assist/Active Distance Assist DISTRONIC (ABA/DTR) (FCW177) control unit. If the fault code is present, check the vertical actual values. If these are not OK, please correct the value with inspection of installation position or calibration of installation height (see attachment 2021 NDTD_Vans_Radar Sensor for best practices and functionality info) If the actual values are OK, please update the software.
- 10228609(SC)Replace Front Door Check
- 10228601(RC)Update Park Lock Function
- 10228600(RC)Update Park Lock Function
- 10228599(RC)Update Park Lock Function
Every Mercedes-Benz Sprinter 1500 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.