2010 Mercury Mariner
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercury › Mariner › 2010
These records cover every 2010 Mercury Mariner. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
3 recalls name the 2010 Mercury Mariner. Newest first.
Ford Motor Company (Ford) is recalling certain model year 2010-2012 Ford Escape vehicles manufactured February 26, 2009, to April 29, 2012, and 2010-2011 Mercury Mariner vehicles manufactured February 25, 2009, to December 12, 2010. On vehicles with a 3.0L engine, the Fuel Delivery Module (FDM) may crack, causing a fuel leak.
Risk and remedy
Risk
A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy
Ford will notify owners, and dealers will replace the FDM flange with one that has a redesigned fuel supply port, free of charge. Remedy parts are currently unavailable. Interim notices were mailed to owners on December 13, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S41.
The Timken Company (Timken) is recalling certain aftermarket front wheel bearings, part number 510072, sold from January 22, 2015, to May 21, 2015, to be used as service parts on 2001-2012 Ford Escape, 2001-2011 Mazda Tribute, and 2005-2011 Mercury Mariner vehicles. The affected wheel bearings have incorrect dimensions of a 42mm bore, 76mm outer dimension…
Risk and remedy
Risk
Use of an incorrectly sized wheel bearing can adversely affect the braking and steering of the vehicle, increasing the risk of a crash.
Remedy
Timken has begun notifying distributors who will offer purchasers replacement wheel bearings, free of charge. The recall began on May 21, 2015. Owners may contact Timken customer service at 1-866-984-6536.
Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS)…
Risk and remedy
Risk
If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy
Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.
Owner complaints
270 complaints2 involved a crash2 involved a fire6 injuries
What owners report most
Latest complaints
- Steering
The contact owns a 2010 Mercury Mariner. The contact stated that while driving approximately 20 MPH, an alarm sounded, and the steering wheel locked up. The message "Power Steering Assist Fault" was displayed. The contact was able to drive to the residence nearby. The vehicle was not diagnosed or…
The contact owns a 2010 Mercury Mariner. The contact stated that while driving approximately 20 MPH, an alarm sounded, and the steering wheel locked up. The message "Power Steering Assist Fault" was displayed. The contact was able to drive to the residence nearby. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and informed the contact that the vehicle was previously repaired under recall. The failure mileage was approximately 190,000.
- Steering
The contact owns a 2010 Mercury Mariner. The contact stated that after starting the vehicle, the message "Power Steering Assist Failure" was displayed, and the steering wheel became extremely difficult to turn in either direction. The local dealer and manufacturer were notified of the failure, but…
The contact owns a 2010 Mercury Mariner. The contact stated that after starting the vehicle, the message "Power Steering Assist Failure" was displayed, and the steering wheel became extremely difficult to turn in either direction. The local dealer and manufacturer were notified of the failure, but no assistance was provided. The contact was informed that the vehicle was previously repaired under NHTSA Campaign Number: 14V284000 (Steering), which the contact related to the failure. The cause of the failure was not yet determined. The failure mileage was 185,000.
- Electrical system · Engine · Unknown or other
Me and my wife purchased a vehicle from a private seller to use for personal commute. A month later we started to notice more issue were occurring with the car then stated from the seller. I took it to an auto body shop to get it inspected and possibly serviced and upon that inspection the clerk…
Me and my wife purchased a vehicle from a private seller to use for personal commute. A month later we started to notice more issue were occurring with the car then stated from the seller. I took it to an auto body shop to get it inspected and possibly serviced and upon that inspection the clerk stated that there was a milage adjustment done to the vehicle. We contacted the seller to try and return the vehicle and receive our money back, but the dealer refused and requested us to resell it.
- Structure › Body
The passenger side of the subframe has holes and will veer hard right when it brakes
- Steering
Power Steering assist fault went out with no warning. Now steering wheel is locking up while driving. Also when trying to gain speed the vehicle bogs out.
- Fuel/propulsion system
Engine light came on after putting fuel in my car it is hapless the codes read emission and fuel issues to replace cap but it is hapless it says it's an issue that needs to be fixed now my engine light won't go off
- Steering
The power steering assist is malfunctioning and it is available for inspection upon request. The steering wheel is very difficult to turn, it's as if the power steering assist is keeping the wheel from turning. No, but I spoke to someone at Ford and they said that it sounded like my car should be…
The power steering assist is malfunctioning and it is available for inspection upon request. The steering wheel is very difficult to turn, it's as if the power steering assist is keeping the wheel from turning. No, but I spoke to someone at Ford and they said that it sounded like my car should be in the recall that was announced for my vehicle type but my VIN was not included in the recall. My car has not been inspected by anyone but it says right on the dash board digital display that there is a "Power Steering Assist Fault". Ford does this with many vehicles they recall, a lot of vehicles that should be included in the recalls are not and we're supposed to foot the bill for their lack of concern for public safety? It's going to cause an accident but it's my only working car and I can't afford to pay for their mistakes. How many have died due to their negligence I'm wondering.
- Steering
The contact owns a 2010 Mercury Mariner. The contact stated that while driving at approximately 5 MPH and attempting to park the vehicle, the power steering became inoperable. The power steering failure message was displayed. The vehicle was taken to the local dealer but was not diagnosed or…
The contact owns a 2010 Mercury Mariner. The contact stated that while driving at approximately 5 MPH and attempting to park the vehicle, the power steering became inoperable. The power steering failure message was displayed. The vehicle was taken to the local dealer but was not diagnosed or repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The contact stated that the failure was related to NHTSA Campaign Number: 14V284000 (Steering). The failure mileage was unknown.
- Steering
The contact owns a 2010 Mercury Mariner. The contact stated while attempting to pull out of a parking space, she became aware that the electronic power steering was not functioning properly. The EPS warning light was illuminated. The vehicle was not taken to the dealer or an independent mechanic.…
The contact owns a 2010 Mercury Mariner. The contact stated while attempting to pull out of a parking space, she became aware that the electronic power steering was not functioning properly. The EPS warning light was illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 14V284000 (Steering) however, the VIN was not included. The manufacturer was notified of the failure but referred the contact to the NHTSA Hotline for assistance. The failure mileage was 65,000.
- Fuel/propulsion system · Unknown or other
My vehicle keeps throwing codes for the EVAP system. I have noticed many of these vehicles have to have their Purge Valve Cannister replaced along with the selenoid for it. I have to replace mine. Is that not a defect if the vehicle? I have owned several vehicles and never had this issue with any of them.
- Fuel/propulsion system
I bought a 2010 Mercury Mariner on June 22, 2023 from a local dealer. There are several recalls associated with the make and model of the vehicle, but they do not appear to be associated with the VIN on my vehicle. However, the recalls on the vehicle appear to be affecting my vehicle and there is a…
I bought a 2010 Mercury Mariner on June 22, 2023 from a local dealer. There are several recalls associated with the make and model of the vehicle, but they do not appear to be associated with the VIN on my vehicle. However, the recalls on the vehicle appear to be affecting my vehicle and there is a warning on the dashboard of my car about the fuel system which is one of the recalls on the vehicle. Fuel Delivery System is causing issues in my vehicle.
- Fuel/propulsion system · Steering · Suspension
I recently purchase 2010 Mercury Mariner. There is a few errors appearing on the screen in front of the steering wheel. One of the error is "CHECK FUEL LINES." It also has an error about the tire pressure sensor. It also rides roughly, but the wheels are like new, so it feels like the suspension or…
I recently purchase 2010 Mercury Mariner. There is a few errors appearing on the screen in front of the steering wheel. One of the error is "CHECK FUEL LINES." It also has an error about the tire pressure sensor. It also rides roughly, but the wheels are like new, so it feels like the suspension or shocks have something wrong with them. Also, there is a lot of play in the steering wheel when driving it. When I went to check on the recalls in the system by putting in my VIN, it shows that there are no recalls on my vehicle. However, these errors and issues are connected to the recalls for my vehicle. I am sure that these recalls have not been taken care of for this vehicle and they need to be fixed.
- Steering
The contact owns a 2010 Mercury Mariner. The contact stated that the power steering fault warning light was illuminated. The power steering assist had failed which made the vehicle difficult to steer. The contact stated that the power steering fuse lines were replaced; however, the failure…
The contact owns a 2010 Mercury Mariner. The contact stated that the power steering fault warning light was illuminated. The power steering assist had failed which made the vehicle difficult to steer. The contact stated that the power steering fuse lines were replaced; however, the failure persisted. The dealer was contacted, and the contact was informed that the VIN was not included in NHTSA Campaign Number: 14V284000 (Steering). The vehicle was not repaired. The manufacturer was not made aware of the failure. The approximate failure mileage was 125,000.
- Steering
The contact's mother owns a 2010 Mercury Mariner. The contact stated while her mother was driving 45 mph, the steering wheel became difficult to turn. The driver stated the tire pressure and the power steering warning lights were illuminated. The driver was able to park the vehicle on side of the…
The contact's mother owns a 2010 Mercury Mariner. The contact stated while her mother was driving 45 mph, the steering wheel became difficult to turn. The driver stated the tire pressure and the power steering warning lights were illuminated. The driver was able to park the vehicle on side of the road. The owner took the vehicle to the independent mechanic and associated the failure with NHTSA Campaign Number: 14V284000 (Steering), however, the VIN was not included. The vehicle was not diagnosed or repaired. A dealer was not contacted. The manufacturer had been informed of the failure. The failure mileage was approximately 115,437
- Steering
The contact owns a 2010 Mercury Mariner. The contact stated that upon starting the vehicle, the power steering assist fault message flashed on the instrument panel. The contact then stated that excessive force was needed to steer the vehicle. Upon investigation, the contact discovered NHTSA…
The contact owns a 2010 Mercury Mariner. The contact stated that upon starting the vehicle, the power steering assist fault message flashed on the instrument panel. The contact then stated that excessive force was needed to steer the vehicle. Upon investigation, the contact discovered NHTSA Campaign Number:14V284000 (Steering). The contact called the dealer and was informed that the vehicle was not under recall. The manufacturer was notified of the failure and provided the contact with a case number. The vehicle was not repaired. The failure mileage was approximately 121,000.
- Service brakes
Driving downhill after dropping my children off at school heard a loud popping noise and brake pedal fell to the floor. Total loss of brakes. Coasted to the side off the road narrowly avoiding busy intersection. Vehicle was looked at by mechanic, traced to faulty ABS Sensor. Serious safety hazard— Recall must be issued immediately to prevent accidents and injuries!
- Service brakes
Brake pedal went to floor on my 10 Mariner, slid into intersection, no warning lights came on, checked for any fluid leaks and there were none. This is 2nd time it has happened and is extremely dangerous! Believe, like others that it is the ABS control. Ford should fix this immediately!
- Electrical system · Engine
When the weather is hot (close to 100 degrees or more) and I am driving with the a/c - my vehicle on 3 occasions will not start after parking the vehicle and trying to restart it. The red padlock sign blinks and it won't start. At first it is trying to turnover but then will continually sound…
When the weather is hot (close to 100 degrees or more) and I am driving with the a/c - my vehicle on 3 occasions will not start after parking the vehicle and trying to restart it. The red padlock sign blinks and it won't start. At first it is trying to turnover but then will continually sound worse and all other warning lights go haywire. I leave the car alone for half a day and it starts up again like nothing happened. On the fourth occasion, the car stopped while driving, just a quiet shutdown and the car glided. This time it did not work for over 24 hours and then started up again like nothing happened. Multiple mechanics and also the dealership cannot figure out the problem because by the time i have it towed to shop, it works again. They did a full check on the car and cannot find anything wrong and there were no diagnostic codes. This issue happens when the weather is hot and poses a safety concern as now it is shutting off while driving and I become stranded each time. (First incident happened 8/25/18, last incident 5/14/22) Total of 4.
- Fuel/propulsion system
My vehicle has been running out of gas extremely quick. It also leaks underneath when I am pumping gas into the Mariner. I am having a loud thunking sound underneath the vehicle an when I let off the accelerator, my car slowly comes to a hault. My power steering went out one day also without…
My vehicle has been running out of gas extremely quick. It also leaks underneath when I am pumping gas into the Mariner. I am having a loud thunking sound underneath the vehicle an when I let off the accelerator, my car slowly comes to a hault. My power steering went out one day also without warning. I can't figure the problem out except I seen a recall for the power steering module or some sort that has malfunctioned an causes the computer to erase the power steering sensor completely clean of it's existence. Please help!
- Steering
The contact owns a 2010 Mercury Mariner. The contact stated that while making a turn, the steering wheel became difficult to maneuver after completing the turn. The contact stated that no warning lights were illuminated. The contact stated that she would turn the vehicle off and on, and upon…
The contact owns a 2010 Mercury Mariner. The contact stated that while making a turn, the steering wheel became difficult to maneuver after completing the turn. The contact stated that no warning lights were illuminated. The contact stated that she would turn the vehicle off and on, and upon restart, the failure corrected itself. The vehicle was taken to the dealer where it was confirmed that the failure was related to NHTSA Recall Number: 14V284000 (Steering) and the steering column needed replacement. The dealer informed the contact that the parts were on backorder. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the failure and confirmed that parts were on backorder and they were unable to provide a repair date. The failure mileage was unknown. Parts distribution disconnect.
- Steering
My steering column started shaking uncontrollably I noticed that the steering was harder and harder to steer and then it went out completely after my steering wheel was vibrating at a very high speed and shaking and controllably and making weird noises 5 minutes later my entire power steering went…
My steering column started shaking uncontrollably I noticed that the steering was harder and harder to steer and then it went out completely after my steering wheel was vibrating at a very high speed and shaking and controllably and making weird noises 5 minutes later my entire power steering went out I am now forced to drive my vehicle because I have another choice and I have a bad although which is now worse because of the steering my vehicle and the steering being out has messed with my starter it has messed with my brace and it has made my water pump belt fray which almost has broken off my AC compressor does not work my car is just not safe
- Unknown or other
The wheel wells are rusted out in the rear. Of the vehicle
- Unknown or other
The contact owns a 2010 Mercury Mariner. The contact stated while driving approximately 10 MPH and making a left turn, the vehicle came to a complete stop. There was no warning light illuminated on the instrument at the time of the failure; however, the power steering warning had since been…
The contact owns a 2010 Mercury Mariner. The contact stated while driving approximately 10 MPH and making a left turn, the vehicle came to a complete stop. There was no warning light illuminated on the instrument at the time of the failure; however, the power steering warning had since been illuminated. The contact related the failure to NHTSA Campaign Number: 14V284000 (Steering). The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 120,000.
- Steering
the power steering assist fault it just stopped working. very hard to turn I have called dealerships but despite the same make and model of the recall they can't see anything for it when they search online
- Suspension
Brakes inspected, back frame rusting out severe holes, mechanic stated you need another vehicle within a year
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Loss of power steering while driving
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric…
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
- Electronic Throttle Body Malfunction
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this…
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
- Rear Liftgate Window Glass Breakage
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was…
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 102050086F35 Transmission - Fluid leak at left side halfshaft seal - built on or before 10/14/2013
- 10177599These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
- 10177598These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
- 10164508Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
- 10160931On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
- 10140323The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
- 10138524The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
- 10137113Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
- 10109070The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
- 10095184Replacing the original equipment sync/navigation system with either an aftermarket sync/navigation kit or modifying original sync/navigation parts to provide additional features IS not recommended nor supported on any ford, mercury or lincoln vehicle. Only approved genuine ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: monroney label (window sticker), professional technician society (pts) oasis tab select sync or hvbom. For genuine ford accessories use: pts workshop tab select dealer installed accessory or accessory installation.
- 10091151Some 2008-2017 ford/mercury/lincoln vehicles equipped with sync may generate a vhr that identifies a concern with the brakes and suspension category indicating service IS required due to a brake system warning lamp being illuminated. If the park brake was applied when the vhr was gathering data from the major vehicle systems, the brakes and suspension message will be reported as the vhr looks for any warning lamps illuminated in the instrument cluster. Rerun the vhr with the engine on and vehicle in park, and ensure the park brake IS disengaged. If the sync vhr IS still reporting a concern to the customers sync owners account, refer to the appropriate workshop manual section for diagnosis by dtc or symptom. Starting in 2015 not all sync equipped vehicles support vhr, refer to the owners manual for vhr operation.
- 10090681Some 2008-2017 ford/mercury/lincoln vehicles equipped with sync may generate a vhr that identifies a concern with the brakes and suspension category indicating service IS required due to a brake system warning lamp being illuminated. If the park brake was applied when the vhr was gathering data from the major vehicle systems, the brakes and suspension message will be reported as the vhr looks for any warning lamps illuminated in the instrument cluster. Rerun the vhr with the engine on and vehicle in park, and ensure the park brake IS disengaged. If the sync vhr IS still reporting a concern to the customers sync owners account, refer to the appropriate workshop manual section for diagnosis by dtc or symptom. Starting in 2015 not all sync equipped vehicles support vhr, refer to the owners manual for vhr operation.
- 100752736F35 TRANSMISSION - FLUID LEAK AT LEFT SIDE HALFSHAFT SEAL BUILT ON OR BEFORE 10/14/2013 ISSUE Some 2009-2014 Escape, 2009-2011 Mariner, 2010-2014 Fusion, 2010-2011 Milan, 2012-2014 Edge/Explorer, and 2013-2014 Taurus/MKT/MKZ vehicles built on or before 10/14/2013 and equipped with a 6F35 automatic transmission may exhibit a fluid leak from the left hand (LH) transmission halfshaft seal due to wear on the transmission case bushing.
- 10057860Ford: in valve body, a worn solenoid pressure regulator valve has diagnostic trouble code (dtc) p0735 stored and indication of repair history was the valve body was not replaced previously. Model 2009-10 escape, mariner, 2010 fusion, milan.
- 10057834Ford: no service action IS recommended for this condition. Please use at your discretion. Various 2010-2015 vehicles may experience a turbulence noise, similar to an helicopter noise, at highway speeds when the rear door window(s) or sunroof are open.
- 10056710Mercury/ford: in one or more speed settings, electronic manual temperature control (emtc) a/c system IS warm and/or lack blower motor operation in settings due to damaged blower motor resistor caused by water entering heater and evaporator core housing. Model 2008-12 escape, mariner.
- 10056183Ford: the throttle body internal motor contacts may be contaminated, resulting in an electrical, intermittent, connectivity, causing malfunction indicator lamp (mil) or wrench light to be illuminated. Model 2009-2012 fusion, milan, escape, mariner. Updated 11/18/14.
- 10055355Ford: the wrench light will illuminate when 4X4 function IS inoperative due to active torque coupling solenoid coil wiring being broke, but a kit IS available to service rear axle assembly/rear drive unit (rdu), at lower level. Model 2008-2012 escape, mariner.
- 10055321Mercury/ford: on some vehicles, there IS a fluid leakage, coming from left hand (lh) halfshaft seal of the automatic transmission and a service kit IS available now, for repair. Model 2009-2012 escape, mariner, fusion, milan.
- 10054926Ford: throttle body will develop contamination on internal motor contacts resulting in an intermittent electrical connectivity and malfunction indicator lamp (mil) or wrench light will illuminate. Model 2009-2013 fusion, milan, escape, mariner. Updated 5/7/14.
- 10054916Ford/mercury: if diagnostic code b2278 IS stored in power steering control module (pscm), it needs replacing with torque sensor service kit that IS available and if not, does not apply. Model 2008-2012 escape, 2008-2011 mariner.
- 10054575Ford: on the left hand half shaft seal, there IS a fluid leak from the transmission because of wear on case bushing. Model 2009-2012 escape, 2009-2011 mariner, 2010-2012 fusion, 2010-2011 milan.
- 10053656Ford: due to an intermittent loss of rpm or lack of acceleration, in some vehicles, with illuminated wrench light, diagnostic trouble codes (dtcs) p2111, p2112 may or may not be stored in powertrain control module (pcm). Models 2009-12 escape, mariner, fusion, milan.
- 10052191Ford/lincoln/mercury: some vehicles may experience an illuminated mil or safety stop now message, or a no start condition or possible misfire or roughness at idling through 2000rpm or a lack of acceleration. Models 2009-12 escape, 2009-11 mariner, milan, 2010-12 fusion, 2011-14 mustangs, 2013 c-max, fusion, MKZ hybrid.
- 10043648Ford: the variable camshaft timing vct) solenoid movement may be temporarily restricted due to debris in engine oil that IS causing diagnostic trouble codes (dtcs).
- 10040948Ford: there may be a leaking/stuck canister purge valve which can cause multiple driving systems. The malfunction light may be on with or without stored trouble codes.
- 10039137Ford: the transmission may leak fluid from a seal. 2009-2010 escape/mariner.
- 10039080Ford: the liftgate window glass may break in cold temperatures. 2010-2011 escape/mariner.
- 10039064Ford: there may be a hard start or rough idle accompanied with two trouble codes. The problem may have to do with camshaft timing. 2010-2011 fusion/escape/milan/mariner.
- 10037561Ford: vehicles may run rough, hard start after refueling, clicking noise under hood, and have trouble codes stored.
- 10037097Ford: some hybrid vehicles may have a malfunction light on with two possible fault codes.
- 10037083Ford: on various 2009-2010 models there may be a malfunction light on with five possible fault codes.
- 10034548Ford/mercury: steering column pop/clunk noise on turns. Some vehicles may exhibit a pop or clunk noise from the steering column area while turning. This noise typically occurs quarter turn before the steering wheel reaches it's end of travel stop and typically goes away with weight off the wheels.
- 10034530Ford/mercury: clunk noise at steering; stops during first lock to lock cycle. The noise typically occurs during tight parking lot maneuvers. The clunk noise heard on the first steering lock to lock cycle IS a normal characteristic of the system.
Every Mercury Mariner model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.