2008 BMW 550I
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2008 BMW 550I. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
2 recalls name the 2008 BMW 550I. Newest first.
BMW is recalling certain model year 2008 through 2010 528i, 535i, 550i, and M5 passenger cars manufactured from March 1, 2007, through December 31, 2009. Over time, increased resistance at the taillight electrical contact points may cause damage to the ground terminal and housing of the connector resulting in an intermittent or permanent loss of…
Risk and remedy
Risk
Intermittent light operation reduces the ability to warn other motorists of the driver's intentions, increasing the risk of a crash.
Remedy
BMW will notify owners, and dealers will replace the rear lamp bulb carriers free of charge. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
On certain vehicles equipped with V8 engines, in conditions of below freezing temperatures combined with low humidity, it IS possible for electrostatic discharge to occur at the fuel rails. if this were to occur, the engine electronic control unit (ecu) could be affected so that engine stalling could result.
Risk and remedy
Risk
If stalling were to occur, the driver may not be able to maintain vehicle speed or accelerate and the power steering could fail increasing the risk of a crash.
Remedy
Dealers will attach two ground cables in the engine compartment free of charge. the recall began on october 29, 2007. owners may contact BMW at 1-800-831-1117.
Owner complaints
32 complaints1 involved a crash3 involved a fire1 injuries
What owners report most
Latest complaints
- Electrical system · Engine
Vehicle abruptly shut off while reversing out of my driveway. Vehicle restarted after a long crank and appeared to enter a reduced power mode/limp mode with a transmission fault that locked the transmission in 4th gear. Reading OBD2 codes revealed a code for the crankshaft position sensor.…
Vehicle abruptly shut off while reversing out of my driveway. Vehicle restarted after a long crank and appeared to enter a reduced power mode/limp mode with a transmission fault that locked the transmission in 4th gear. Reading OBD2 codes revealed a code for the crankshaft position sensor. Inspection of the 3 terminal sensor revealed 2 of the terminal contacts on the sensor to be shorted out with melted plastic on both the sensor and the wiring connector plug. Shorted wire could be a result of a leaking coolant passage at rear of engine within bellhousing where sensor is located. Coolant intrusion into sensor connector resulted in electrical short and melted connections.
- Engine
The contact owns a 2008 BMW.The contact stated that he was getting ready to drive the vehicle, however when he started the vehicle, the ABS and check engine lights illuminated.The contact stated that he noticed the vehicle was overheating and turned the vehicle off.The contact heard an unusual…
The contact owns a 2008 BMW.The contact stated that he was getting ready to drive the vehicle, however when he started the vehicle, the ABS and check engine lights illuminated.The contact stated that he noticed the vehicle was overheating and turned the vehicle off.The contact heard an unusual sound which came from under the hood.The contact inspected and noticed that the coolant reservoir lid had detached and dented the hood due to the vehicle overheating.The vehicle was not diagnosed or repaired by an independent mechanic or dealer.The manufacturer was made aware of the failure and provided no assistance.The failure mileage was approximately 65,000.
- Exterior lighting
The daytime running lights aka Angel Eyes wiring is sub-standard. The plastic coating on the wires for the daytime running lights/Angel Eyes has melted away exposing bare wiring that has fused causing the lights to malfunction and not work. I believe the manufacturer is aware of this sub-standard issue and needs to provide a suitable fix or replacement for the sub-standard wiring of their product.
- Electrical system
I was driving and came to a stop and noticed smoke and an odd smell coming from under the hood. The heater control valve and the wire connector started to smolder and melt the plastic. If it wasn’t for me disconnecting the connector wire to the heater control valve, it would have definitely would…
I was driving and came to a stop and noticed smoke and an odd smell coming from under the hood. The heater control valve and the wire connector started to smolder and melt the plastic. If it wasn’t for me disconnecting the connector wire to the heater control valve, it would have definitely would have caught on fire.There was no warning other than the smoke and smell coming from the car. I am in the process of the car getting inspected from a bmw service center
- Electrical system · Exterior lighting
The wiring in my headlight assembly is crumbling and the headlight is shorting out. The coating on the wiring is trash. I own a 08 Bmw550i. BMW should be ashamed. Thanks [XXX] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
- Vehicle speed control › Accelerator pedal
The contact owns a 2008 BMW 550I. The contact stated while driving 65 MPH, the accelerator pedal was depressed however, the vehicle failed to respond. There was no warning light illuminated. The contact pulled over to the side of the roadway and turned off and restarted the vehicle however, the…
The contact owns a 2008 BMW 550I. The contact stated while driving 65 MPH, the accelerator pedal was depressed however, the vehicle failed to respond. There was no warning light illuminated. The contact pulled over to the side of the roadway and turned off and restarted the vehicle however, the battery warning light illuminated and remained illuminated. The vehicle was taken to an unknown dealer and was previously repaired under an unknown recall. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 141,000.
- Electrical system · Engine
Vehicle parked for days, noticed smoke from passenger side engine bay, inspection found possible faulty electrical wiring or oil leak onto electrical wiring causing small fire on engine floor. Disconnected negative terminal to battery.
- Power train
I was driving on the freeway and the power train light came on and the car began to loose a lot of power then when I pulled to side of the road the car turned of and would not start until several attempts . I waited about 8 min then started to drive . And it does this all the time now . Then the light goes out and drives fine . But this always happens . And it's very dangerous. I've been in some tight situations.
- Air bags · Engine · Seat belts
Car smokes bad valve seals and seatbelt restrain went bad twice and car seat adjustment goes bad
- Electrical system · Exterior lighting · Unknown or other
I have been in contact with BMW of north america for 8 weeks. My 2008 BMW 550I caught fire while stationary at a gas station at the gas pump. The fire department was called out to contain the fire. The fire inspector and the fire chief both stated that it was a wiring issue. I have the fire report.…
I have been in contact with BMW of north america for 8 weeks. My 2008 BMW 550I caught fire while stationary at a gas station at the gas pump. The fire department was called out to contain the fire. The fire inspector and the fire chief both stated that it was a wiring issue. I have the fire report. I was finally able to get BMW of north america to inspect the vehicle on feb. 5, 2018 and was told there 'looks like there could have been'work done to the wiring of the car. I have owned the vehicle since april 2017 (7 months) and have not done any work to the wiring. I also pulled a carfax report before purchasing the vehicle. It showed 0 accidents and 0 major mechanical working. I asked BMW for a copy of the inspector's report and was denied. That really made me suspect something foul from BMW.
- Exterior lighting
Frayed and disintegrating headlight wiring present throughout my headlamps. These are sealed enclosures for which there are no preventive maintenance items. This IS a serious safety issue as the headlights may fail without warning, particularly in hot weather. These are non consumer replaceable parts and prohibitively expensive to replace and should not be failing after only 8 years of service.
- Exterior lighting
I had a parking light go bad and while I was replacing it I noticed that the wiring inside the headlight assembly IS no longer insulated. the insulation has become brittle and IS flaking off. I removed the cover for the other headlight and the same thing has happened to that light. it would seem that these bare wires could cause a vehicle fire.
- Exterior lighting
Bought a 2008 BMW 550I and experienced headlight failure with the headlight fuse blowing repeatedly when I went to change the bulbs noticed that all the wires in the headlight were bare. Used liquid insulation to fix the issue however have seen numerous of this car catching fire from the issue after some research
- Air bags
Consistently receiving 'passenger restraint system' warning indicating loss of airbag protection on onboard warning system. dealership support notified several times while under manufacturer as well as purchased extended warrantees without any remedy. 'no fault' found by dealerships - reportedly…
Consistently receiving 'passenger restraint system' warning indicating loss of airbag protection on onboard warning system. dealership support notified several times while under manufacturer as well as purchased extended warrantees without any remedy. 'no fault' found by dealerships - reportedly their diagnostics indicated no current issue with passenger restraint system. passenger restraint system continues to indicate shut-down while under normal driving conditions. limited online research indicates that this IS a persistent passenger safety control system issue specific to this manufacturer and model.
- Seat belts
Waring light for seat belt restraint stays on, only on passenger side. Not sure if this affects integrity of seat belt or air bags.
- Air bags · Seat belts
Purchased used with 83,000 miles. currently 100,000. the intermittently reports a failure in the passenger restraint system. when examined by a qualified mechanic, there IS no indication of an issue with any of the passenger restraint systems. when this warning IS present on the vehicle, I do…
Purchased used with 83,000 miles. currently 100,000. the intermittently reports a failure in the passenger restraint system. when examined by a qualified mechanic, there IS no indication of an issue with any of the passenger restraint systems. when this warning IS present on the vehicle, I do not know what safety systems (if any) have been compromised. dealership has stated there IS a recall on similar vehicles during the same year, but not this vehicle even though it uses the same components.
- Air bags · Seat belts
Pass restraint system error. Please help! I get this warning every so often when I get in my car and regardless of a passenger present or not. Several times the beeping signal will begin to make noise, to button the seat belt, even when nothing IS in the seat. this IS creating a very annoying driving experience.
- Electrical system · Exterior lighting
I recently started experiencing fuses blowing on my right front head light units. errors would indicate it was the 'right daylight parking unit' and then would clear or stay constant. when it was constant, it was due to a blown fuse. it turns out when I had a BMW certified technician look at the…
I recently started experiencing fuses blowing on my right front head light units. errors would indicate it was the 'right daylight parking unit' and then would clear or stay constant. when it was constant, it was due to a blown fuse. it turns out when I had a BMW certified technician look at the issue he said that the problem was related to the wiring inside the front head light. the wiring had insulation that was starting to flake off allowing contact of the two wires going to the bulb and was even apparent on other wires within the head light assembly. if I hit a bump or went over rumble strips these wires could touch and short causing the fuse to blow and/or error message. after 3 fuses and buying an unnecessary set of H8 bulbs, the technician fixed the wiring with some electrical tape but suggested that a file a complaint here since there IS no open recall for this common issue. he also told me this problem with wire insulation falling off was very common on bmw's that were 5-7 years old. I could see burn marks on the wire an installation from where the short occurred and was shocked that all the wiring within the head lamp on both the right and left front showed these flaking and cracking. after researching online at several BMW forums I found many similar issues and images almost identical to the ones my technician took. I would like a recall to be issued by BMW to replace the head light assemblies or internal wiring with wires that have a better/proper insulator that doesn't flake off. I've not had the back lights checked, but found that this IS common on most if not all BMW light assemblies front/back for a few online research queries. also where can I send the digital pictures my technician took of the wiring?
- Tires
I got this zenna tires from carshoez.com and the tires have a tread pattern wrong. It does not for with the flow of rotation of the tire. The inside side tread IS going backward and the outside tread IS backward on two tires and forward on the other two tires. Tires sizes IS 275/30/19 rear and 245/35/9 front. *tr
- Air bags · Seats
TL* the contact owns a 2008 BMW 550I. The contact stated that the air bag warning light illuminated. The vehicle was taken to the dealer who recommended that the passenger seat sensor needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 68,000.
- Air bags
I was driving and a warning light came on, the warning says (pass. Restraint system. Fault in passenger-restraint system affecting air bag, belt tensioner belt-force limiter. Continue wearing safety belt. Have system checked by the nearest BMW center. I was driving normally with no sudden stop or any out of the ordinary move.
- Engine
TL* the contact owns a 2008 BMW 535I. The contact stated that while traveling 30 mph, the engine temperature warning light illuminated. The contact was able to drive the vehicle to his residence. The vehicle was not taken to a mechanic. The vehicle was not repaired. The manufacturer was contacted about the issue. The failure and current mileages were 78,000.
- Service brakes, hydraulic
TL* the contact owns a 2008 BMW 550I. The contact stated that the when depressing the brake pedal the vehicle would hesitate to stop. The dealer was notified and diagnosed that the vaccum pump was leaking oil. The manufacturer was also notified, but stated that the vehicle was not included in the…
TL* the contact owns a 2008 BMW 550I. The contact stated that the when depressing the brake pedal the vehicle would hesitate to stop. The dealer was notified and diagnosed that the vaccum pump was leaking oil. The manufacturer was also notified, but stated that the vehicle was not included in the recall associated with nhtsa campaign ID number 10v446000 (service brakes, hydraulic:power assist:vacuum). The vehicle was not repaired. The failure and current mileages were 85,000.
- Electrical system · Engine and engine cooling · Power train
Vehicle shuts off unexpectedly and fails to restart, additionally the vehicle will randomly fail to start. the engine will shut off while driving at highway speeds, when driving slowly, or shortly after shifting the car into drive from park. no warnings or errors are generally encountered or…
Vehicle shuts off unexpectedly and fails to restart, additionally the vehicle will randomly fail to start. the engine will shut off while driving at highway speeds, when driving slowly, or shortly after shifting the car into drive from park. no warnings or errors are generally encountered or logged however in rare instances drivetrain warnings are displayed. the engine displays no strange behavior prior to this occurring and shuts off as if it were instructed to do so. the vehicle regularly fails to start. the engine does not turn over at all or make any indication that it IS attempting to start. the vehicle responds as though the ignition was not activated and was never instructed to start. after a random time interval from 5 minutes to 2 hours the car will start as if no problems were ever encountered. no errors are logged in the ecu. the manufacturer has yet to find any issues which they claim are repairable after approximately 40 days of shop time and well over 100 occurrences. *tr
- Power train › Clutch assembly · Power train › Manual transmission
2008 BMW 550I. Consumer states when normally down shifting to reduce speed, the cruise control would not disengage when the clutch was pushed in *tgw the consumer stated when the clutch was released in a lower gear, it maintained the higher speed and merely revved the engine. the consumer…
2008 BMW 550I. Consumer states when normally down shifting to reduce speed, the cruise control would not disengage when the clutch was pushed in *tgw the consumer stated when the clutch was released in a lower gear, it maintained the higher speed and merely revved the engine. the consumer learned he could not down shift, but had to break instead. the consumer and the BMW technician went for a test drive and it was soon discovered that the clucth had to be held for about six seconds in order for the cruise control to disengage. The dealer informed the consumer the delay was apparently within the specifications
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10249437The basic conditions for initializing the power windows are not met.
- 10249027The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.
- 10247567Engine will crank but not start. There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE
- 10245422Customers may state that the alarm system (DWA) is not active after locking their unoccupied vehicle. Depending on the vehicles equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.
- 10194296Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
- 10182619Discharged Battery Energy Diagnosis Must Be Performed: The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.
- 10175267Power Reduction FC2A82 Intake VANOS and/or FC2 A87 Exhaust VANOS Camshaft Fault: The "Service Engine Soon" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.
- 10162428Various Electrical Problems Caused by Water Ingress. Water ingress into the luggage compartment may cause various electrical problems or faults associated with the MPM (Micro Power Module); PDC (Park Distance Control); M-ASK (Multi-Audio System Controller); CCC (Car Communication Computer); CID (Control Information Display); TCU (Telematics Control Unit); LOGIC-7 (Top Hi-Fi); RDC (Tire Pressure Monitor) or SDARS (Satellite Radio Receiver) control modules. In most cases, the water collects in the spare wheel recess. CAUSE: Insufficient sealing may allow water to enter the luggage compartment due to the vacuum generated while driving.
- 10152289"?CLASS ACTION LAW SUIT SETTLEMENT: WATER INTRUSION AND ACCUMULATION IN THE TRUNK (E60)/REAR CABIN WELL AREA (E61). INFORMATION BMW of North America, LLC (?BMW NA?) is has entered into a court approved ?nationwide settlement? with this Class Action?s lawsuit plaintiffs. Class Allegations In their complaint, the plaintiffs allege that:Model Year 2004 to 2010 BMW 5 Series E60 (Sedans) and Model Year 2006 to 2010 E61 (Sport Wagons) vehicles (""Preliminary Class Vehicles"") have defectively designed sunroofs drains which, if they become clogged, causes water intrusion and accumulation in the trunk/rear cabin well area of these vehicles. As a result, over time, this can potentially damage the electrical components and wiring that is located in the lowest part of the well area. Final Settlement Class Vehicles US specification Model Year 2007 to 2010 BMW 5 Series E60 (Sedans) and E61 (Sport Wagons) vehicles (""Final Settlement Class Vehicles"") registered and operated in the US (including Puerto Rico). Cass Members US residents (including Puerto Rico) who purchased or leased a Class Vehicle. Settlement Terms for Final Settlement Class Vehicles For eligible vehicles, the free inspection is available one-time (repair/claim dates) beginning on 8/28/2017 but no later than the extended date of 11/21/2018, Class Members will be permitted to bring their Class Vehicle to an authorized BMW center to have the free one-time inspection and control module relocation procedure performed. SI B01 28 17 (DC 54 12 90 01 00) CLASS ACTION LAWSUIT SETTLEMENT: WATER INTRUSION AND ACCUMULATION IN THE TRUNK (E60)/REAR CABIN WELL (E61) AREA, MAY APPLY. FOR ELIGIBLE VEHICLES, AN INSPECTION AND APPLICABLE CORRESPONDING REPAIRS ARE AVAILABLE ONE-TIME (REPAIR/CLAIM DATES) BEGINNING ON 8/28/2017 BUT NO LATER THAN THE EXTENDED DATE OF 11/21/2018. CLASS ACTION LAWSUIT SETTLEMENT: WATER INTRUSION AND ACCUMULATION IN THE TRUNK (E60)/REAR CABIN WELL (E61) AREA, SERVICE INFORMATION BULLETIN SI
- 10151335Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
- 10151323ELV Does Not Release. The customer complains of a no-crank, no-start situation. The condition may be intermittent. The ELV (Electric Steering Lock) warning is shown in the Instrument Cluster.
- 10151119SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.
- 10151115SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
- 10151068This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
- 10151023Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
- 10150385"CCC - ""Please Insert Navigation DVD"" Appears on CID. The navigation map DVD cannot be read or detected. The message ""Please insert navigation DVD"" appears in the CID (Central Information Display). The navigation system is inoperative. This situation may also occur when upgrading to a new navigation map. The old map is recognized but the new one is not. CAUSE Faulty DVD drive; read error due to hardening of the anti-vibration gel on the read head"
- 10150330"Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle ""discharged battery"" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the ""Procedure"" section of this Service Information for details."
- 10150130The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
- 10150099N54 Engine: Fuel Pressure Control Test Plan Error. INFORMATION Not applicable.
- 10150065"BMW NA has agreed to extend the emissions warranties of the turbocharger's wastegate to: ??8 years or 82,000 miles, whichever occurs first, as determined from the vehicle's original in-service date select the ""Vehicle Comment"" button to display the extended coverage information. The terms of the original New Vehicle/SAV Limited Warranty and applicable emissions warranty still apply. BMW NA will not provide warranty coverage to any Settlement Class Member's vehicle containing modifications or alterations to the turbocharger or its wastegates (software, hardware or otherwise), or evidencing other conditions not normally covered under the original New Vehicle/SAV Limited Warranty or applicable emissions warranty. Modifications excluded from warranty coverage include any aftermarket parts that affect the turbocharger system, or if there are other conditions that would normally exclude it from warranty coverage."
- 10149605Battery Replacements. A failed battery in the vehicle is being replaced with a battery of a different size and type, which can lead to additional labor to retrofit the differently sized battery. CAUSE In the past, the 110 AH Lead acid battery was not available. The 90/92 AH AGM battery was installed as an alternative replacement; this required retrofitting.
- 10149589"N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (""wet"") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the ""N54 Engine Diagnostic Fault Tree"" file (the current version ""02_14_13"" is found as a PDF attachment to SI B12 55 06)."
- 10149382iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
- 10149279Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
- 10148423Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: z 213901 - Power management: Reduction or shutdown of individual electrical consumer z 8040BD - Reset or deactivation of Terminal 30F z 8040B9 - De-activation of terminal 30B: Top start capability limit reached z 8020E8 - Reset or deactivation of terminal 30F z 800E89 - FRM: start capability limit reached with lights active during stationary mode z 93076B - Deactivation of terminal 30B: upper start capability limit reached z 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active z 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active z 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE z The check control message (ID 229) is caused by a heavily discharged battery. z The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). z In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. z Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. z The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
- 10148376Previously assigned radio channels to the satellite radio "Presets" list have been erased and radio channels selected from the list "All channels" menu cannot be stored in the "Presets" list. The problem occurred after the recently implemented Sirius/XM channel lineup change. The data handling between the satellite radio receiver (SDARS-Exbox) and the Car Communication Computer (CCC head unit) has been corrupted.
- 10148276Traffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
- 10148273Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
- 10148194iPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.
- 10148166N62TU: EDK Throttle Potentiometer Faults - Diagnostic. The "Service Engine Soon" and DSC/DTC warning lights are illuminated. Engine enters the power reduction ("fail-safe") mode. The following intermittent and "currently not present" EDK related faults may be stored in DME fault memory: ? 2CF8 - Throttle valve potentiometer, signal; and /or? 2CF9 - Throttle valve potentiometer 1, signal; and/or ? 2CFA - Throttle valve potentiometer 2; signal. In most cases DSC fault 5F77 (DME invalid data) may also be stored in DSC control module. These faults are sporadic and usually not reproducible. Resistance fluctuation in the EDK harness connector is causing an interruption of the EDK signal.
- 10148135ConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
- 10148120Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
- 10148101iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
- 10148034"Intelligent Battery Sensor Diagnosis Hints. The vehicle enters the workshop with one or more of the following complaints: * Check Control Message related to battery discharge * No-start condition * Consumer power reduction (reduced blower speed, heated seats operation, etc.) * The following fault codes may be stored in the DME a. 2E8B - Intelligent battery sensor, signal b. 2E8C - Intelligent battery sensor, function c. 2E8D - Intelligent battery sensor, signal transmission d. 2E8E - Intelligent battery sensor, communication CAUSE A faulty battery or IBS sensor (not both) The power management system and IBS in the vehicle cannot determine if the battery needs to be replaced. This is normal operation for all E-Series vehicles because they do not have the Advanced IBS sensor that the F-Series vehicles do. An external battery tester (Midtronics EXP-1000) must be used to determine if the battery needs to be replaced. Energy Diagnosis will not prompt for a battery replacement unless the battery is ""aged."" When energy diagnosis identifies the battery as ""aged,"" it means the amount of energy discharge over the course of the life of the battery has reached its maximum (worn out). In most cases, energy diagnosis states that the battery is OK. This is typically an indication of the current State of Charge (SoC), not the State of Health (SoH). The SoC is defined as the current amount of energy left in the battery (displayed as a percentage). The SoH is defined as an evaluation of the condition of the battery over a period of time (displayed as a percentage). For more information about batteries, refer to Training Manual ST051, ""07 Battery Basics."""
- 10148018"?SI B01 09 14 September 2014 WarrantiesWarranties This Service Information bulletin supersedes SI B01 09 14 dated August 2014. Please read this Service Information bulletin in its entirety, the content has been completely updated. designates changes to this revision SUBJECT Front Passenger Air Bag Seat Occupancy Sensor (OC3) Mat: Limited Warranty Extension to 15 years Without Mileage Limitation. INFORMATION BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the Supplemental Restraint System's (SRS) front passenger air bag seat occupancy sensor (OC3) mat on certain model BMW vehicles to: 15 years without mileage limitation as determined by the vehicle's original in-service date. This ""component-specific"" limited warranty extension applies to defects in materials and workmanship. This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. No immediate repair is required unless the BMW vehicle is currently experiencing this problem. This extended limited warranty coverage does not apply to vehicles affected by the following Recall Campaign: Recall 13V-564: E90, E91 Front Passenger Air Bag Seat Occupancy Sensor MatRecall 13V-564: E60, E61,E65, E66 Front Passenger Air Bag Seat Occupancy Sensor MatSI B65 08 14Recall Campaign 13V-564: Replace Front Passenger Air Bag Seat Occupancy Sensor (E60, E61, E65, E66)Recall 13V-564: E65,E66 Front Passenger Air Bag Seat Occupancy Sensor Mat (E65, E66)Recall 13V-564: Front Passenger Air Bag Seat Occupancy Sensor Mat for Sport Seat (E60, E61, E65, E66)Recall 13V-564: E53 Repair Front Passenger Air Bag Seat Occupancy Sensor MatThe extended limited warranty coverage also does not apply to: ??Vehicles with other seat options, and ??E60 (M5) vehicles Note: Please refer to SI B65 75 06 for the limited warranty extension information that applies to previous models. Customer Notification Letter - VIN and Component-specific Warranty Extension Even tho
- 10148010ConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
- 10147953"ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle."
- 10147945Delay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
- 10147941ELV Does Not Release. Cause 1: The steering column is held against the steering lock because of torque from the steering gear. In such cases, a yellow check control warning (CC ID# 187) is shown in the instrument cluster, but no faults are stored. Cause 2: Communication fault in the CAS (Car Access System) and ELV system network and/or battery low. The problem may cause the ELV warning to be displayed in yellow or red.
- 10147837"The Disclaimer screen automatically disappears from the CID after 10 seconds. INFORMATION https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/28...12/2/2015 Page 2 of 2 An enhancement was made to the Car Communication Computer (CCC) and MASK (Multi Audio System Controller) in 2006 so the customer does not have to manually accept the ""Disclaimer"" screen each time. Older vehicles prior to the production dates listed above that are programmed with ISTA/P 2.52 or higher will also get this enhancement. WARRANTY INFORMATION Not applicable."
Every BMW 550I model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.