2007 Dodge Nitro
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Dodge › Nitro › 2007
These records cover every 2007 Dodge Nitro. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2007 Dodge Nitro. Newest first.
Chrysler (FCA US LLC) is recalling certain 2008-2010 Chrysler Town and Country and Dodge Grand Caravan and 2007-2011 Dodge Nitro vehicles. These vehicles may have a loose or missing brand emblem in the center of the steering wheel. The loose emblem or the securing nuts for the emblem within the driver air bag module may become projectiles in the event of…
Risk and remedy
Risk
Projectiles as a result of driver air bag deployment in the event of a crash can increase the risk of injury.
Remedy
Chrysler will notify owners, and dealers will replace the driver's air bag cover with a redesigned cover, free of charge. The recall began February 11, 2021. Owners may contact FCA US LLC customer service at 1-800-853-1403. Chrysler's number for this recall is W09.
Chrysler Group LLC (Chrysler) is recalling certain model year 2007-2008 Dodge Nitro 4X2 vehicles manufactured March 21, 2006, through March 1, 2008; and 2008 Jeep Liberty 4X2 vehicles manufactured February 15, 2007, through March 1, 2008. The transfer case heat shield may drop down and rub on the drive shaft, weakening it and potentially causing the drive…
Risk and remedy
Risk
If the drive shaft breaks, a section of it can strike the transfer case tunnel with enough force that the airbag computer will believe the vehicle is in a crash and thus deploy the airbags. Additionally, the drive shaft failure will result in a loss of motive power. Either condition may increase the risk of a crash.
Remedy
Chrysler will notify owners, and dealers will add a bracket to support the rear of the heat shield, free of charge. An interim letter was mailed to owners on May 29, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N10.
Chrysler IS recalling certain model year 2007 dodge nitro passenger vehicles. the windshield wiper system may experience a condition over time where high usage of the variable pause wiper function ("delay" mode) may eventually affect primary wiper function, rendering the wiper system inoperable.
Risk and remedy
Risk
Inoperative wipers under inclement weather conditions could cause impaired visibility increasing the risk of a crash.
Remedy
Dealers will inspect and add external relays and update the totally integrated power module software to control the wiper functions. the safety recall IS expected to begin during february 2010. owners may contact chrysler at 1-800-835-1403.
Chrysler IS recalling 3,663 my 2007-2008 dodge nitro and my 2008 jeep liberty vehicles equipped with manual transmissions. the park brake lever clutch drum may distort and reduce the effectiveness of the park brake system.
Risk and remedy
Risk
This could allow the vehicle to move inadvertently and cause a crash without warning.
Remedy
Dealers will replace the park brake lever assembly free of charge. the recall began on october 27, 2008. owners may contact chrysler at 1-800-853-1403.
On certain sport utility vehicles, the software programmed into the ABS electronic control module may allow a momentary delay in braking when coasting up a hill during certain conditions.
Risk and remedy
Risk
This could cause a crash without warning.
Remedy
Dealers will reprogram the ABS electronic control module with new software that prevents this condition free of charge. the recall began on october 22, 2007. owners may contact chrysler at 1-800-853-1403.
On certain vehicles, the totally integrated power module (tipm) was programmed with software that may allow the engine to stall under certain operating conditions.
Risk and remedy
Risk
This could cause a crash without warning.
Remedy
Dealers will reprogram the tipm. the recall began on july 5, 2007. owners may contact daimlerchrysler at 1-800-853-1403.
On certain vehicles, the antilock brake system (ABS) control module software may cause the rear brakes to lock up during certain braking conditions.
Risk and remedy
Risk
This could result in a loss of vehicle control and cause a crash without warning.
Remedy
Dealers will reprogram the ABS electronic control unit. the recall began on february 19, 2007. owners may contact daimlerchrysler at 1-800-853-1403.
Owner complaints
494 complaints16 involved a crash11 involved a fire22 injuries
What owners report most
Latest complaints
- Electrical system · Unknown or other · Visibility/wiper
The day after I bought this vehicle it had to go directly back because of the catalytic converter. I was told they replaced it but did not show me the proof nor did they give me a valid warranty card. There is something wrong with the electrical system everything flickers and it just sounds…
The day after I bought this vehicle it had to go directly back because of the catalytic converter. I was told they replaced it but did not show me the proof nor did they give me a valid warranty card. There is something wrong with the electrical system everything flickers and it just sounds really bad. The driver side passenger side window broke because it's made of plastic. The front both passenger and driver side door handles broke off. I had to Jerry rig it. And the reason I think this would be dangerous is if we were to need to get out of the car we would not be able to in case of an emergency. I've looked under the items that were recalled on this vehicle. But I get a notification that says I'm not allowed to have it fixed. Unless it's out of pocket. I purchased this car in August 2015 or 2016. The dates on the calendar below are inaccurate because the catalytic converter was done the very next day and the driver side indoor handle has been broken off for quite a while. But recently in the last week or so the other one snapped off.
- Air bags · Power train · Structure
The contact owned a 2007 Dodge Nitro. The contact received notification of NHTSA Campaign Number: 13V121000 (POWER TRAIN, AIR BAGS, STRUCTURE). The contact stated that while stopped, the sound of an explosion was heard, and the side air bags deployed. The contact believed the vehicle had been…
The contact owned a 2007 Dodge Nitro. The contact received notification of NHTSA Campaign Number: 13V121000 (POWER TRAIN, AIR BAGS, STRUCTURE). The contact stated that while stopped, the sound of an explosion was heard, and the side air bags deployed. The contact believed the vehicle had been struck by another vehicle. The contact suffered injuries to the neck and had issues with his hearing. The contact stated that medical attention was not required. A Police report was not filed. The vehicle was towed to the residence, and then towed to the dealer, where it was diagnosed that the underbody shield was striking the drive shaft while driving. The vehicle was not repaired. The manufacturer advised the contact that a field inspector would be sent to inspect the vehicle. The field inspector inspected the vehicle and the contact was awaiting the results. The failure mileage was approximately 78,000.
- Visibility/wiper
Our heater core has gone out twice now, preventing us from properly being able to defrost our windows /windshield in winter and remove moisture during cooler days. It creates a substantial risk by reducing, or in some cases, completely removing visibility
- Electrical system · Steering · Unknown or other
Ever since I bought this vehicle, I have been having issues with it registering the key, which keeps causing an automatic security alert system to shut down my vehicle the moment I start it. I've already replaced the battery to my car. I've already had locksmiths examined the issue and nobody can…
Ever since I bought this vehicle, I have been having issues with it registering the key, which keeps causing an automatic security alert system to shut down my vehicle the moment I start it. I've already replaced the battery to my car. I've already had locksmiths examined the issue and nobody can seem to find the problem. The issue with the car is definitely a security issue. The car shuts down automatically and goes into theft mode which prevents me from driving my vehicle. That could be a result to a software malfunction or something but it doesn't register the keys which originally sets off the security warning. Whenever the car does register the key it drives and operates just fine. It's the computer that prevents me from driving it or whatever automatic system that is related to theft mode.
- Electrical system
This 2007 Dodge Nitro R/T 4x4 electrically stalled and died at 65mph on the [XXX] . This is the 3rd time it has stalled out electrically. The vehicle was inspected and told bad TIMP. Told the G25 RECALL should be placed on this vehicle. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Air bags · Power train · Structure
The contact owns a 2007 Dodge Nitro. The contact stated that the air bag warning light was illuminated. The vehicle was taken to an unknown dealer, where the vehicle was repaired under NHTSA Campaign Number: 13V121000 (Power Train, Air Bags, Structure); however, the failure persisted. The vehicle…
The contact owns a 2007 Dodge Nitro. The contact stated that the air bag warning light was illuminated. The vehicle was taken to an unknown dealer, where the vehicle was repaired under NHTSA Campaign Number: 13V121000 (Power Train, Air Bags, Structure); however, the failure persisted. The vehicle was taken back to the dealer but was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was unknown.
- Engine · Unknown or other
I had my vehicle a week before it start misfiring it’s been months I had it worked on numerous times and still has not been fixed. When I try to crank it I have to keep my foot on the gas and if I let go it will cut back off I had so many parts replaced and the issue remain the same
- Visibility/wiper
Took car in for windshield wiper safety recall on 3/24/23. BEFORE the recall the wipers worked perfectly. After the dealer serviced the wipers they sometimes would not go off and then seemed to be stalling a lot but I did not have many occasions where I needed to use the wipers as I work from…
Took car in for windshield wiper safety recall on 3/24/23. BEFORE the recall the wipers worked perfectly. After the dealer serviced the wipers they sometimes would not go off and then seemed to be stalling a lot but I did not have many occasions where I needed to use the wipers as I work from home and have a second car in the household. Today I was driving in a severe thunderstorm when they stopped working completely. In fact, they are now stuck in the upright position and will not move. This is EXTREMELY dangerous and exactly what the recall was meant to avoid! It makes me wonder if the mechanics actually did anything to my car at all.
- Power train · Structure
The contact owns a 2007 Dodge Nitro. The contact stated that the underbody shield was striking the drive shaft while driving. The vehicle was serviced under NHTSA Campaign Number 13V121000 (Power Train, Air Bags, Structure) however, the fix failed to repair the vehicle. The vehicle was taken to the…
The contact owns a 2007 Dodge Nitro. The contact stated that the underbody shield was striking the drive shaft while driving. The vehicle was serviced under NHTSA Campaign Number 13V121000 (Power Train, Air Bags, Structure) however, the fix failed to repair the vehicle. The vehicle was taken to the dealer to be diagnosed. The vehicle was not repaired. The manufacturer was notified of the failure but offered no assistance. The failure mileage was 201,500.
- Electrical system · Fuel/propulsion system
My car didn’t want to start after seeing a check engine light saying cylinder 2 misfire then 4 had fuel pump replaced still had check engine light and was misfiring afterwards a week or two the truck stalled while driving off freeway in middle of traffic breakers did not work, car frozen almost…
My car didn’t want to start after seeing a check engine light saying cylinder 2 misfire then 4 had fuel pump replaced still had check engine light and was misfiring afterwards a week or two the truck stalled while driving off freeway in middle of traffic breakers did not work, car frozen almost wrecked. I had it towed back to garage and they replace fuel pump again but car won’t stay on it will turn on then shut off by itself not showing any codes mechanics can’t find issue over 2 weeks at garage already!!
- Visibility/wiper
Windshield wipers stopped working while in the “on” position on the windshield. I replaced the wiper motor but the wipers still do not work. Yes, this issue was inspected by several reputable mechanics and service centers. This issue causes safety issues as I live in a region who experiences most…
Windshield wipers stopped working while in the “on” position on the windshield. I replaced the wiper motor but the wipers still do not work. Yes, this issue was inspected by several reputable mechanics and service centers. This issue causes safety issues as I live in a region who experiences most of almost all precipitation including rain, hail, snow and etc. I am unable to drive under these conditions because I am unable to use my wipers. There were no warning signs or messages before the wipers failed. I was informed by the Dodge/Chrysler dealership that this is a common issue with this truck and year.
- Unknown or other
Throttle body light came on car died. Thought it was throttle body replaced it didn’t start. It has crank but no start. Have had 11 people look at it now have replaced spark plugs, coils, battery terminals, crankshaft sensor, camshaft sensor, fuel pump but the car still will not start. I was told…
Throttle body light came on car died. Thought it was throttle body replaced it didn’t start. It has crank but no start. Have had 11 people look at it now have replaced spark plugs, coils, battery terminals, crankshaft sensor, camshaft sensor, fuel pump but the car still will not start. I was told the tipm could cause this issue I need to know what else I can do. I have no vehicle now can’t work due to this and I am struggling to get by. No codes show up, no blinking red light for the key, checked the fuses, checked fuel pressure. Been down a month now.
- Exterior lighting
Brake light have stopped working randomly. Were working fine one day then next day I have no brake lights, I've had several people see if they could find the problem with no success. Could possibly be faulty wiring to the brake lights? Put just normal tail lights work with only those lights when breaking. I've also seen several same make and model vehicles with the same issue in the same town that I live
- Electrical system · Engine · Unknown or other
The TIPM is starting to fail. The power locks do not work, the car has problems starting has a very slow start, the horn will randomly go off and sometimes it does not want to start at all. Every article I’ve read, and every dealership I’ve talked with has said to replace the entire TIPM module.…
The TIPM is starting to fail. The power locks do not work, the car has problems starting has a very slow start, the horn will randomly go off and sometimes it does not want to start at all. Every article I’ve read, and every dealership I’ve talked with has said to replace the entire TIPM module. There are many other cases like this and it all comes down to the module. So with this said I am asking for either reassurance that it is that. Or receive help to be able to fix it.
- Unknown or other
While filling gas Leaks out filler Nozzle
- Visibility/wiper
Wipers have stopped working after the recall was repaired
- Air bags · Electrical system · Service brakes
The wiper relays went out recently and somehow caused the door locks to beep and go crazy then die completely. And a few weeks ago the brake came undone somehow and fell into the wheel well, ripping the inside of the rim open causing a blow out while my wife, 2 year old and I were on the freeway.…
The wiper relays went out recently and somehow caused the door locks to beep and go crazy then die completely. And a few weeks ago the brake came undone somehow and fell into the wheel well, ripping the inside of the rim open causing a blow out while my wife, 2 year old and I were on the freeway. And now after taking it to 2 different dodge dealerships, the problems are not fixed, there is more warning lights on than I've ever seen. And so far both places have told me they fixed an emblem on the steering wheel, and that the other recalls aren't applicable because of being a 2007 and the recalls are for the 2008. Even though my nitro is obviously having the same if not worse problems. All the way down to the emergency brake not working, we love our nitro and dodge as a company and would please like some kind of help with this situation. Our vehicle is our only source of transportation and it is not safe for us to be driving, especially in the winter conditions we just got hit with here. Thank you for your help to whom this may concern. Here are some pictures of what happened with the brakes, thank the lord we were getting off the freeway when the brakes gave way, if we had been on the freeway 15 seconds more, the accident would have been fatal without question.
- Visibility/wiper
The vehicle windshield wiper system comes on while driving constantly. It is very distracting and definitely causes an obstruction in your visibility. It is very annoying as well. It acts as if the wiper system does not want to go in the park position on the wiper motor.
- Exterior lighting · Suspension · Vehicle speed control
I was driving down the rd and all of the sudden my truck jumps into 2nd gear and looses all power to speed up and it seems like I'm in neutral my relay box is messing up everything electrical now it shuts off at stop signs and If it keeps doing all this I'll have to replace transmission. I've already replace tipm 2 times
- Electrical system · Engine · Fuel/propulsion system
Four total incidents of the vehicle engine shutting off while driving the car. Most recent today 12-17-21 was placed in extremely dangerous situation and was almost rear ended 5 times by other vehicles traveling at speeds greater than 55 mph. 1st instance occurred back in 2007 traveling West bound…
Four total incidents of the vehicle engine shutting off while driving the car. Most recent today 12-17-21 was placed in extremely dangerous situation and was almost rear ended 5 times by other vehicles traveling at speeds greater than 55 mph. 1st instance occurred back in 2007 traveling West bound on I635 in Dallas (speed of 65mph) engine shut off, loss of power steering coasted to side of road. 2nd incident Fall 2007 - from complete stop to turn left and cross divided highway, the engine shut down right in the middle of the intersection and was nearly broadsided by oncoming car traveling at 45 mph. 3rd incident happened while driving in my neighborhood, engine shut down and loss of power to steering. Daimler Chrysler issued a recall to reprogram the TPIM module back in 2008 to address the problem. Nothing since then until today. I am the original Owner of this car and it has been well maintained and is still covered under the manufacturers warranty for as long as I own the vehicle. What has prompted me to report this problem is the fact that I could have been seriously injured. There was no warning whatsoever and the place where this took place had a blind spot as the car lost power during the climb and coasted at 2 mph down slope on a bend on the bridge. Cars traveling towards me had no visibility to my vehicle which was for all practical purposes at a stand still. I notified the Dodge Chrysler dealership of what took place and will also contact MOPAR to raise this serious problem. If a vehicle doesn't start is one thing, but to have a car loose power out of nowhere without warning has almost cost me serious harm on multiple occasions. Daimler Chrysler should do something before loss of life takes place.
- Electrical system · Power train
I noticed a few months ago my dash lights and radio lights at night when I turn my headlights on would flicker on and off several times then stop and do it again repeated process. I never got it looked at so just the other day I was driving and my windshield wipers, my emergency flashers and my…
I noticed a few months ago my dash lights and radio lights at night when I turn my headlights on would flicker on and off several times then stop and do it again repeated process. I never got it looked at so just the other day I was driving and my windshield wipers, my emergency flashers and my driverside window and the back passenger window was all going crazy my widows was rolling up and down my flashers was going off and my wipers wouldn't turn off so I immediately pull over fearing of causing an accident with someone due to not being able to focus on driving once I pulled over my horn started blowing like crazy it was weird so I cut the vehicle off and everything kept doing what it was doing so I popped the hood and killed the battery. I waited maybe 10 minutes and hooked the battery back up and seconds later my horn only started going crazy again so I had no option out of the safety of me and other vehicles on the road to just have it towed back to my house I have been researching it and I've come to find out that there's several others with dodge nitros that have had the same issue as me. The tipm module (fuse box) was bad. I have yet to be able to drive my vehicle as it would be very unsafe and I've not yet got it towed to the dealership to look at it for reasons of what I've seen other complaints had to say about there experience at the dealership.. there needs to be a recall on the electrical malfunction as it is a huge!!! Safety concern for everybody. Please do something about this.
- Unknown or other
My engine stalled. But only when the transmission was at park. It happened twice in 5 years and when it was raining. Also my engine struggles a bit to turn on in the morning but only in the summer time. If it’s winter car starts up with ease. But I do notice when my engine is fully warm and I shut…
My engine stalled. But only when the transmission was at park. It happened twice in 5 years and when it was raining. Also my engine struggles a bit to turn on in the morning but only in the summer time. If it’s winter car starts up with ease. But I do notice when my engine is fully warm and I shut off my car to go to a store, when I go back and turn on my car it will just crank. I have to shut it off and then turn it back on.This happens quite often. And this only happens in the winter in a fully warmed engine. Not the summer. This been happening about three years now. I’ve got it inspected but nothing is found wrong.
- Fuel/propulsion system · Unknown or other · Visibility/wiper
1. Engine light on reads gas cap . We replaced gas cap numbers times and engine light doesn’t go away. 2. Wipers not working . Water cleaning spray for windows not working front or back windows. 3. I have replaced my windows panel numerous times. The window panels keep braking and my windows stay down. Extremely annoying.
- Air bags
My airbag light doesn’t go off after the recall fix that was recently sent out. I took my car in for the recall fix and the airbag light is still on. Is my car even safe to drive now ?
- Electrical system
The check engine light turn on for a day or two then it turns off . Three or two Months later it does the same thing .
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Totally Integrated Power Module Failure
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007…
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den
- Fleet Vehicle Recall Completion Audit
On November 18, 2010, NHTSA's Recall Management Division (RMD) opened an audit query (AQ10-001) to investigate recall remedy completion by rental car companies on safety recall campaigns.It was expected to provide the agency an indication of how completely and how quickly rental car fleets perform necessary…
On November 18, 2010, NHTSA's Recall Management Division (RMD) opened an audit query (AQ10-001) to investigate recall remedy completion by rental car companies on safety recall campaigns.It was expected to provide the agency an indication of how completely and how quickly rental car fleets perform necessary recall-related remedies on the vehicles owned and then rented/leased for use on the roadways.RMD queried three (3) major motor vehicle manufacturers (Ford, Chrysler, and General Motors) and requested data regarding completion figures for fifteen (15) discreet safety recalls.Analysis of this data demonstrated that rental car recalls completion was neither complete nor consistent.The rental car companies representing the largest market share in the industry were then queried as to their respective policies for the rental, lease, and sale of vehicles with open recalls.The data and responses from the manufacturers and the rental car companies can be found in the document repository by accessing the ?Associated Documents link above.In December 2015, Congress enacted the Fixing America's Surface Transportation (FAST) Act.One section of the Act prohibits rental car companies from renting, leasing, or selling motor vehicles subject to open safety recalls.With the passage of the FAST Act and its prohibition, there is no continuing need for the agency to investigate rental car recall completions.Accordingly, this investigation is closed.The agency reserves the right to open any future investigations, including audits of individual recalls, or groups of recalls, or rental car companies, to examine more closely safety recalls performance and completion issues in this area.
- Engine stalling & electric power loss
On july 3, 2007, daimlerchrysler corporation (dcc) submitted a defect information report to nhtsa describing a defect that could result in engine stall while driving in approximately 80,894 model year (my) 2007 jeep wrangler and dodge nitro vehicles manufactured between january 30, 2006 and january 22, 2007 (nhtsa…
On july 3, 2007, daimlerchrysler corporation (dcc) submitted a defect information report to nhtsa describing a defect that could result in engine stall while driving in approximately 80,894 model year (my) 2007 jeep wrangler and dodge nitro vehicles manufactured between january 30, 2006 and january 22, 2007 (nhtsa recall 07v-291, dcc recall g25).according to dcc, the totally integrated power module (tipm) in these vehicles was programmed with software that may allow the engine to stall under certain conditions.dcc will reprogram the tipm in the recalled vehicles with revised software. Odi opened pe07-027 on may 29, 2007, based on 53 complaints alleging engine stall and/or loss of electrical power in my 2007 jeep wrangler vehicles.odi was also monitoring similar complaints in my 2007 dodge nitro vehicles.dcc's analysis of complaints to dcc and nhtsa found that many described events with a momentary loss of electrical power inside the vehicle and a corresponding loss of engine power.many of the reports also indicated that the instrument cluster telltale lamps momentarily illuminated during the event. Dcc's engineering analysis determined that the tipm could initiate an internal reset cycle lasting approximately 75 ms in response to error messages on the communication bus.the key on signal from the tipm to the powertrain control module (pcm) IS lost during a tipm reset.if the pcm loses the key on signal for longer than 40 ms, it interprets it as the vehicle ignition being turned off and begins a power down routine.after the tipm reset, the key on signal IS restored and the pcm powers back up.if the rotating components of the engine contain sufficient inertia, the vehicle may restart with no input from the operator as reported in some of the complaints.if the engine does not restart in this manner, it can be restarted by the operator.a revision to the tipm software on january 22, 2007 changed the tipm reset time to 17 ms, removing the potential for pcm power down and engine stall. Odi has received 178 complaints potentially related to the alleged defect in my 2007 jeep wrangler vehicles and 52 complaints involving my 2007 dodge nitro vehicles.two of the nitro complaints allege that a crash resulted from an engine stall incident, one of which caused minor injuries to a passenger.as of june 1, 2007, dcc identified 151 wrangler complaints and 128 nitro complaints. This investigation has been closed with dcc's recall.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10229181Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223854Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].
- 10223602Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223599Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10221831(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
- 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
- 10220843NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission
- 10220576SAFETY RECAL W09 DRIVER AIR BAG EMBLEM Updated Dealer Instructions
- 10220471Mechanical rocker arm, intake, 1.7 ratio.
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10216395Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10216269Fuel Spit Back During Refueling Due To Inlet Check Valve (X46 Lifetime Warranty Extension) This bulletin involves replacing the fuel tank with a revised part. Some customers may experience a fuel spit back condition during a refueling event.
- 10215825Some of the above vehicles may experience a condition where the underbody transmission tunnel shield may partially separate from the vehicle floor pan and contact the aluminum driveshaft. Operating the vehicle with the transmission tunnel shield rubbing against the driveshaft could weaken the driveshaft at the rub point and cause it to break.
- 10204370Customer Satisfaction Notification Y22 Driver Airbag Emblem
- 10204368Customer Satisfaction Notification Y22 Driver Airbag Emblem
- 10191460Valve Body. These may cause over drive cycling.
- 10191442Mechanical rocker arm, intake, 1.7 ratio.
- 10190590NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission
- 10188780SAFETY RECAL W09 DRIVER AIR BAG EMBLEM Updated Dealer Instructions
- 10188658Some of the above vehicles may experience a condition where the underbody transmission tunnel shield may partially separate from the vehicle floor pan and contact the aluminum driveshaft. Operating the vehicle with the transmission tunnel shield rubbing against the driveshaft could weaken the driveshaft at the rub point and cause it to break.
- 10180221(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
- 10175743Disinfectant Solution Recommended for COVID-19
- 10175735Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
- 10171324This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the geometry of the part. There is a feature on the assembly that is intended to provide clearance to the door handle, it may not provide enough clearance which could prevent the door handle from being installed.
- 10171323This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the geometry of the part. There is a feature on the assembly that is intended to provide clearance to the door handle, it may not provide enough clearance which could prevent the door handle from being installed.
- 10169249Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10169247Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10169245Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10140065Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10139978Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
- 10138987Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10136479Fuel Spit Back During Refueling Due To Inlet Check Valve (X46 Lifetime Warranty Extension) This bulletin involves replacing the fuel tank with a revised part. Some customers may experience a fuel spit back condition during a refueling event.
- 1012900882212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
- 10128983Fuel Spit Back During Refueling Due To Inlet Check Valve (X46 Lifetime Warranty Extension) This bulletin involves replacing the fuel tank with a revised part. Some customers may experience a fuel spit back condition during a refueling event.
- 10128948Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10121927NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
Every Dodge Nitro model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.