2008 Dodge Nitro
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Dodge › Nitro › 2008
These records cover every 2008 Dodge Nitro. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
3 recalls name the 2008 Dodge Nitro. Newest first.
Chrysler (FCA US LLC) is recalling certain 2008-2010 Chrysler Town and Country and Dodge Grand Caravan and 2007-2011 Dodge Nitro vehicles. These vehicles may have a loose or missing brand emblem in the center of the steering wheel. The loose emblem or the securing nuts for the emblem within the driver air bag module may become projectiles in the event of…
Risk and remedy
Risk
Projectiles as a result of driver air bag deployment in the event of a crash can increase the risk of injury.
Remedy
Chrysler will notify owners, and dealers will replace the driver's air bag cover with a redesigned cover, free of charge. The recall began February 11, 2021. Owners may contact FCA US LLC customer service at 1-800-853-1403. Chrysler's number for this recall is W09.
Chrysler Group LLC (Chrysler) is recalling certain model year 2007-2008 Dodge Nitro 4X2 vehicles manufactured March 21, 2006, through March 1, 2008; and 2008 Jeep Liberty 4X2 vehicles manufactured February 15, 2007, through March 1, 2008. The transfer case heat shield may drop down and rub on the drive shaft, weakening it and potentially causing the drive…
Risk and remedy
Risk
If the drive shaft breaks, a section of it can strike the transfer case tunnel with enough force that the airbag computer will believe the vehicle is in a crash and thus deploy the airbags. Additionally, the drive shaft failure will result in a loss of motive power. Either condition may increase the risk of a crash.
Remedy
Chrysler will notify owners, and dealers will add a bracket to support the rear of the heat shield, free of charge. An interim letter was mailed to owners on May 29, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N10.
Chrysler IS recalling 3,663 my 2007-2008 dodge nitro and my 2008 jeep liberty vehicles equipped with manual transmissions. the park brake lever clutch drum may distort and reduce the effectiveness of the park brake system.
Risk and remedy
Risk
This could allow the vehicle to move inadvertently and cause a crash without warning.
Remedy
Dealers will replace the park brake lever assembly free of charge. the recall began on october 27, 2008. owners may contact chrysler at 1-800-853-1403.
Owner complaints
393 complaints17 involved a crash12 involved a fire18 injuries
What owners report most
Latest complaints
- Electrical system · Engine
An intermittent electrical failure is affecting multiple vehicle systems. The vehicle has unexpectedly stalled while driving on the interstate, leaving it without power in moving traffic. It has also experienced repeated no-start conditions, transmission entering limp mode, the engine continuing to…
An intermittent electrical failure is affecting multiple vehicle systems. The vehicle has unexpectedly stalled while driving on the interstate, leaving it without power in moving traffic. It has also experienced repeated no-start conditions, transmission entering limp mode, the engine continuing to run after the key was removed, and random operation of the horn, windshield wipers, washer pumps, and other electrical components while driving and while parked. These failures occur without warning and create a serious risk of a crash, injury, or death due to sudden loss of propulsion in interstate traffic and unpredictable vehicle behavior. The problem has become progressively more frequent despite previous repairs. The vehicle is available for inspection. I fear for my life.
- Electrical system
Car shut off while driving, prior have had issues. Have replaces TIPM module, ignition, grounding, etc
- Air bags · Power train · Structure
The contact owns a 2008 Dodge Nitro. The contact stated that while the son was driving approximately 5 MPH, the front drive shaft fractured, causing the vehicle to abruptly stop, and the front driver's side and passenger's side airbags erroneously deployed. The contact stated that there was no…
The contact owns a 2008 Dodge Nitro. The contact stated that while the son was driving approximately 5 MPH, the front drive shaft fractured, causing the vehicle to abruptly stop, and the front driver's side and passenger's side airbags erroneously deployed. The contact stated that there was no collision during the incident. The contact's son sustained a concussion and facial injuries, causing severe swelling to the face and severe headaches. No medical treatment was received, but the son remained bed ridden for several days from the injuries sustained during the air bag deployment. The cause of the failures were not determined. The manufacturer and the local dealer were notified of the failures. The contact was informed of NHTSA Campaign Number: 13V121000(Power Train, Air Bags, Structure), which the contact's son related to the failure. The failure mileage was 203,000.
- Electrical system
TIPM system and/or electrical system failure. Right turn signal intermittently works when it wants to. Door locks from the inside at random or will not lock at all when using the master lock button. Now car will not start or turn over at all. Zero sound comes from he vehicle while turning the key.…
TIPM system and/or electrical system failure. Right turn signal intermittently works when it wants to. Door locks from the inside at random or will not lock at all when using the master lock button. Now car will not start or turn over at all. Zero sound comes from he vehicle while turning the key. Commonly known problem with other Dodge Nitros and nothing being done about it. A recall needs to happen or at the very least acknowledgement from Dodge.
- Electrical system
I had just entered Gene Snyder Expressway going west when my throttle light started flashing and I lost gas pressure and it started going down fast and then it shut off and right in the middle of rush-hour traffic and it’s 65 mph on the expressway and People as usual go around 80 mph and I just…
I had just entered Gene Snyder Expressway going west when my throttle light started flashing and I lost gas pressure and it started going down fast and then it shut off and right in the middle of rush-hour traffic and it’s 65 mph on the expressway and People as usual go around 80 mph and I just entered and almost got slammed in the rear but luckily I got off the highway in time. I still have not been able to turn my truck over at all. It is in the throttle electrical system, which is currently being checked out as we speak but it’s spit out two codes. One was PO633 and one was P2 112.
- Service brakes · Steering · Wheels
Esp bas lights (appeared after). as I was driving, the car felt like it hit a brick wall even though it didnt, it slammed me into the steering wheel and then continued driving. At that point, the esp bas light came on. Have attempted to contact dodge or chrysler by phone with no chance at reaching a person cause of robotic answering services.
- Electrical system · Unknown or other
TIPM connectors melted. Ground wires melted.
- Electrical system · Engine · Power train
The vehicle throws the abs, esp,break and traction control lights and then while driving completely at random then turns off WHILE DRIVING!!!! which can cause an accident (I and my daughter are lucky to be alive) this is not ok the vehicle drives fine then at random throws those lights and shuts…
The vehicle throws the abs, esp,break and traction control lights and then while driving completely at random then turns off WHILE DRIVING!!!! which can cause an accident (I and my daughter are lucky to be alive) this is not ok the vehicle drives fine then at random throws those lights and shuts off after restarting it the check engine light comes on and says the transmission shift solenoid b is malfunction and the vehicle wouldn't shift properly. Luckily I had my code reader I. The car with me I cleared the code and now the car drives fine until this happens again I'm scared to drive it this is dangerous their's no warning. I drive on the highway everyday their's no warning it happens at random 2 times I've been lucky. No codes came up driving after clearing it and the car drives fine now but it's happened 2 times while driving this is extremely dangerous and I don't know what to do because with the codes gone the issues are gone but they randomly all the lights mentioned above come on and then the car shuts off with no warning then when you restart it it throws a different code for a different problem the first time was a low voltage code I cleared it and even Tho my battery tested good I replaced it and two days later the same issue and a different code
- Power train · Steering
Power steering locks up, power steering fluid not helping. Looks like oil mixed in with the coolant. Car smoking and overheating
- Air bags
2008 Dodge nitro in a collision going between 35 and 45 miles per hour had a major rear end accident. Police paramedics and fire came on scene. The air bags never deployed. This vehicle was taken for the air bags emblem recall in 2022. The vehicle should have air bags that deploy.
- Electrical system
Was driving tipm caught fire Now insurance telling me moisture and corrosion
- Electrical system › Horn · Visibility/wiper
The contact owns a 2008 Dodge Nitro. The contact stated that the horn and the rear and front windshield wipers were inoperable. There was no warning light illuminated. The contact attempted to restart the vehicle however, the failure persisted. The contact stated that her neighbor disconnected and…
The contact owns a 2008 Dodge Nitro. The contact stated that the horn and the rear and front windshield wipers were inoperable. There was no warning light illuminated. The contact attempted to restart the vehicle however, the failure persisted. The contact stated that her neighbor disconnected and reconnected the battery and the failure was corrected. The vehicle was not diagnosed. Neither the dealer nor the manufacturer was contacted. The failure mileage was 168,000.
- Electrical system › Horn · Visibility/wiper
The contact owns a 2008 Dodge Nitro. The contact stated that while entering the vehicle the horn inadvertently started blowing and windshield wipers activated independently. There were no warning lights illuminated. The vehicle was taken to the dealer and diagnosed with an unknown electrical wiring…
The contact owns a 2008 Dodge Nitro. The contact stated that while entering the vehicle the horn inadvertently started blowing and windshield wipers activated independently. There were no warning lights illuminated. The vehicle was taken to the dealer and diagnosed with an unknown electrical wiring failure. The dealer replaced the battery cables; however, the failure recurred. The manufacturer was not notified of the failure. The approximate failure mileage was 57,000.
- Electrical system
The contact owns a 2008 Dodge Nitro. The contact stated while driving approximately 40 MPH, the windows, lights, and radio would independently turn off, or on. The contact stated that occasionally while driving, the vehicle lost motive power and stalled. The contact was able to coast off the road…
The contact owns a 2008 Dodge Nitro. The contact stated while driving approximately 40 MPH, the windows, lights, and radio would independently turn off, or on. The contact stated that occasionally while driving, the vehicle lost motive power and stalled. The contact was able to coast off the road safely. The contact stated that she then got out the vehicle to look under the hood to tap the TIPM box, which allowed her to restart the vehicle. The contact stated that she had contacted the dealer to schedule an appointment. The manufacturer was notified of the failure and informed the contact that the there was no recall on the VIN for the failure. The failure mileage was 85,648.
- Unknown or other
I have received multiple recall notices (recall W09/NHTSA 20V-396) since the recall was issued on my vehicle 20 months ago however I have been unable to get the recall completed because Dodge will not provide the parts needed to complete the repair. The notices all say that the part is available…
I have received multiple recall notices (recall W09/NHTSA 20V-396) since the recall was issued on my vehicle 20 months ago however I have been unable to get the recall completed because Dodge will not provide the parts needed to complete the repair. The notices all say that the part is available yet when my dealership tries to get the part, they are told it is out of stock with no eta as to when it will be available. This is NOT a timely manner and Dodge needs to provide the part now.
- Fuel/propulsion system
Gas keeps overflowing every time I pump gas into no matter what pump or gas station I am using.
- Electrical system
The TIPM in these vehicles are faulty and nothing is being done about it by Dodge. There are hundreds of complains across several forums and every time Dodge is contacted about the issue they use the no recall excuse. I have a Nitro myself and it has multiple electrical issues for no reason other…
The TIPM in these vehicles are faulty and nothing is being done about it by Dodge. There are hundreds of complains across several forums and every time Dodge is contacted about the issue they use the no recall excuse. I have a Nitro myself and it has multiple electrical issues for no reason other than poor manufacturing. The TIPM is the issue and it's not just my Nitro having this problem. My vehicle has accelerated without my assistance, it's had braking issues when there should be no issue. Components that need my action to work have activated on their own, such as... horn, wiper, wiper fluid, accelerator, etc... The wiring in these vehicles are faulty and it needs to be fixed by the manufacturer at their expense. It's time they step up a make it right by the consumer.
- Fuel system, gasoline
The contact owns a 2008 Dodge Nitro. The contact stated while attempting to refuel the vehicle, the fuel was spilling from the vehicle onto the ground. The vehicle was not diagnosed nor repaired. The manufacturer was informed of the failure and informed the contact that the vehicle was not under recall. The failure mileage was approximately 130,000.
- Electrical system · Engine · Exterior lighting
It started with all dash lights coming on saying it had issues and then just stopped dead in road. I had tpim put in, then alternator , and then new battery. Was fine and then head lights stopped coming on . Next, it starting with horn, and everything under the sun coming on and not stopping.…
It started with all dash lights coming on saying it had issues and then just stopped dead in road. I had tpim put in, then alternator , and then new battery. Was fine and then head lights stopped coming on . Next, it starting with horn, and everything under the sun coming on and not stopping. Took to shop and they thought they found it, and drove for a day and as soon as I turned on headlights it stalled. In motion on a street driving.
- Air bags · Seat belts · Structure › Body
On 2/11/2021 me an my mom was head to doctor at 445am and it was just raining cold and we hit a patch of ice going 20 miles and hour and I lost control and we went rolling 3 times and air. Bags did not deploy and the seat belt restriors didnt restrict as we was rolling some time in process my…
On 2/11/2021 me an my mom was head to doctor at 445am and it was just raining cold and we hit a patch of ice going 20 miles and hour and I lost control and we went rolling 3 times and air. Bags did not deploy and the seat belt restriors didnt restrict as we was rolling some time in process my head hit windshield and got knocked out it was on a hwy moving their was no one on the road but us.. It wount let me up load my pictures I have but will be glade to mail them to u waiting on police report he put wrong information about me on for so it needto be fixed.*dt
- Air bags · Service brakes
Took my vehicle in for a recall. The recall was for replacing the emblem on the steering wheel. The emblem was removed but the replacement cover was not installed. Also the recall for the drive shaft was not done.
- Electrical system · Engine
TL* the contact owns a 2008 dodge nitro. The contact stated that when the vehicle was unlocked, the alarm, windshield wipers, and horn engaged. The electronic throttle control and check engine warning lights were illuminated. The vehicle was towed to the dealer carolina chrysler jeep dodge RAM…
TL* the contact owns a 2008 dodge nitro. The contact stated that when the vehicle was unlocked, the alarm, windshield wipers, and horn engaged. The electronic throttle control and check engine warning lights were illuminated. The vehicle was towed to the dealer carolina chrysler jeep dodge RAM (1001 halstead blvd, elizabeth city, nc 27909, (252) 391-9609) where it was diagnosed that the battery needed to be replaced. The vehicle was repaired however, the failure recurred with the check engine warning light illuminated. The manufacturer was not notified of the failure. The failure mileage was approximately 147,668.
- Fuel system, gasoline
TL* the contact owns a 2008 dodge nitro. The contact stated that the fuel tank would overflow without warning while attempting to refuel vehicle. The contact stated that the failure occurred since owning the vehicle in 2009. The contact recently took the vehicle to carson dodge chrysler jeep RAM…
TL* the contact owns a 2008 dodge nitro. The contact stated that the fuel tank would overflow without warning while attempting to refuel vehicle. The contact stated that the failure occurred since owning the vehicle in 2009. The contact recently took the vehicle to carson dodge chrysler jeep RAM (3059 s carson st, carson city, NV 89701) where she was informed that she had to pay a diagnostic fee to determine the cause of the failure. She declined to pay the diagnostic fee. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 27,000.
- Electrical system
Driving to work and noticed smoke. Opened hood and flames were coming out of fuse box. Closed hood and grabbed purse and phone. Lady who pulled over behind me and people inside office called fire department because engine completely involved. Took a bit for fire dept. To gain control and…
Driving to work and noticed smoke. Opened hood and flames were coming out of fuse box. Closed hood and grabbed purse and phone. Lady who pulled over behind me and people inside office called fire department because engine completely involved. Took a bit for fire dept. To gain control and extinguish. I did research and saw several similar complaints re fuse box. Insurance adjuster to examine 12/7/2020*dt the consumer provided photos. *Tr
- Electrical system · Fuel/propulsion system
Tipm malfunctions..vehicle vibrated and shut off while driving..starter cranked continuously without turning engine over. Continuously ran fuel pump which caused need for replacing,and a new battery as well. After replacing fuel pump,and battery,the vehicle shut off again..while driving. the vehicle,again will not start. Starter keeps running unless you turn the key to the "off position"
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Totally Integrated Power Module Failure
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007…
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10229181Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223854Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].
- 10223602Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223599Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10221831(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
- 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
- 10220843NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission
- 10220576SAFETY RECAL W09 DRIVER AIR BAG EMBLEM Updated Dealer Instructions
- 10220471Mechanical rocker arm, intake, 1.7 ratio.
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10218307Flash: UConnect and Voice Recognition Inoperative This bulletin involves replacing the Hands Free Module (HFM). The customer may describe the following conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality
- 10216395Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10216269Fuel Spit Back During Refueling Due To Inlet Check Valve (X46 Lifetime Warranty Extension) This bulletin involves replacing the fuel tank with a revised part. Some customers may experience a fuel spit back condition during a refueling event.
- 10215825Some of the above vehicles may experience a condition where the underbody transmission tunnel shield may partially separate from the vehicle floor pan and contact the aluminum driveshaft. Operating the vehicle with the transmission tunnel shield rubbing against the driveshaft could weaken the driveshaft at the rub point and cause it to break.
- 10204370Customer Satisfaction Notification Y22 Driver Airbag Emblem
- 10204368Customer Satisfaction Notification Y22 Driver Airbag Emblem
- 10191460Valve Body. These may cause over drive cycling.
- 10191442Mechanical rocker arm, intake, 1.7 ratio.
- 10190590NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission
- 10188780SAFETY RECAL W09 DRIVER AIR BAG EMBLEM Updated Dealer Instructions
- 10188658Some of the above vehicles may experience a condition where the underbody transmission tunnel shield may partially separate from the vehicle floor pan and contact the aluminum driveshaft. Operating the vehicle with the transmission tunnel shield rubbing against the driveshaft could weaken the driveshaft at the rub point and cause it to break.
- 10180221(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
- 10175743Disinfectant Solution Recommended for COVID-19
- 10175735Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
- 10171324This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the geometry of the part. There is a feature on the assembly that is intended to provide clearance to the door handle, it may not provide enough clearance which could prevent the door handle from being installed.
- 10171323This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the geometry of the part. There is a feature on the assembly that is intended to provide clearance to the door handle, it may not provide enough clearance which could prevent the door handle from being installed.
- 10169249Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10169247Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10169245Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10166537RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
- 10140258Flash: UConnect and Voice Recognition Inoperative This bulletin involves replacing the Hands Free Module (HFM). The customer may describe the following conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality
- 10140065Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10139985Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
- 10139978Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
- 10138987Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10136479Fuel Spit Back During Refueling Due To Inlet Check Valve (X46 Lifetime Warranty Extension) This bulletin involves replacing the fuel tank with a revised part. Some customers may experience a fuel spit back condition during a refueling event.
Every Dodge Nitro model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.