2022 Ford Bronco
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Ford › Bronco › 2022
These records cover every 2022 Ford Bronco. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
23 recalls name the 2022 Ford Bronco. Newest first.
Ford Motor Company (Ford) is recalling certain 2021-2026 Bronco and Bronco Raptor vehicles. The engine compartment wiring harness may become damaged and short circuit.
Risk and remedy
Risk
A short circuit in the engine compartment can create heat or spark, increasing the risk of a fire.
Remedy
Dealers will install sheathing over the wiring, free of charge. This is a Phased campaign. Phase 1 will include 2026 Bronco Raptor notified owners on 7/31/2026. Phase 2 will include 2021-2025 Bronco Raptor vehicle will notify owners on or about 8/14/2026. Phase 3 will include 2021-2026 Bronco will notify owners on or about 9/1/2026. Owner notification letters were mailed August 5, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S55. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on July 23, 2026.
Ford Motor Company (Ford) is recalling certain 2022-2026 Bronco vehicles. The fender flares may not be properly secured and detach from the vehicle.
Risk and remedy
Risk
A detached fender flare can become a road hazard and increase the risk of a crash.
Remedy
Dealers will inspect and repair, or replace the fender flares as necessary, free of charge. Owner notification letters were mailed September 1, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S47. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning August 7, 2026.
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The 3-door and 5-door Molded-In-Color (MIC) hardtop roof panels may have been manufactured improperly, which can allow sections of the outer roof panel to separate and detach from the vehicle.
Risk and remedy
Risk
A detached section of roof can create a road hazard, increasing the risk of a crash.
Remedy
Dealers will inspect and replace the hard top as necessary, free of charge. Interim letters, notifying owners of the safety risk were mailed May 28, 2026. Additional letters will be sent once the remedy is available, anticipated in November 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S32. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on May 12, 2026.
Ford Motor Company (Ford) is recalling certain 2021-2025 Bronco vehicles. The transmission to transfer case joint may be misaligned due to an incorrectly performed previous repair, which could lead to wear of the transmission output shaft splines and transfer case input splines.
Risk and remedy
Risk
Excessive wear of the transmission and transfer case splines may result in a loss of drive power or vehicle rollaway, increasing the risk of a crash.
Remedy
Dealers will inspect the transmission to transfer case joint and replace the transmission and transfer case as necessary, free of charge. Owner notification letters were mailed July 9, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S26. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on April 15, 2026.
Ford Motor Company (Ford) is recalling certain 2021-2026 Ford Bronco and 2021-2024 Ford Edge vehicles. The Accessory Protocol Interface Module (APIM) may overheat and shutdown, which can prevent the rearview camera image from displaying as intended.
Risk and remedy
Risk
A rearview camera that fails to display an image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.
Remedy
The APIM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed April 13, 2026. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 26S09. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on March 5, 2026.
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously repaired incorrectly under recall number 23V165. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle…
Risk and remedy
Risk
A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
Remedy
Dealer will update the SYNC module software ,free of charge. Owner notification letters were mailed January 28, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C72. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning January 30, 2026.
Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco vehicles. The front seats may have a loose or dislodged seat frame height-adjust pivot bolt.
Risk and remedy
Risk
A seat with a dislodged bolt may not properly restrain an occupant in a crash, increasing the risk of injury.
Remedy
Dealers will inspect and replace the pivot links and bolts as necessary, free of charge. Owner notification letters were mailed April 28, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SB5. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov beginning October 28, 2025.
Ford Motor Company (Ford) is recalling certain 2016-2019 Lincoln MKC, 2016-2023 Explorer, 2019-2020 Fusion, 2019-2024 Ranger, 2020-2022 Lincoln Corsair, Escape, 2021-2024 Bronco, Bronco Sport, and 2022-2024 Maverick vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Risk and remedy
Risk
An electrical short circuit can increase the risk of a fire.
Remedy
Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded blanking plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed December 3, 2025. Additional letters will be sent once the final remedy is available, anticipated December 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 15, 2025.
Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco, Explorer, Lincoln Aviator, F-250 SD, F-350 SD, F-450 SD, F-550 SD, 2021-2022 Lincoln Navigator, Mustang, F-150, and 2022 Expedition vehicles. The low-pressure fuel pump may fail, which can result in an engine stall while driving.
Risk and remedy
Risk
An engine stall increases the risk of a crash.
Remedy
Dealers will replace the low pressure fuel pump on super duty vehicles and update the powertrain control module (PCM) software on all other affected vehicles, free of charge. Owner notification letters were mailed July 27, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S75.
Ford Motor Company (Ford) is recalling certain 2022-2023 Bronco vehicles. The 360-degree view camera may not display a rearview image when the vehicle is placed in reverse.
Risk and remedy
Risk
Loss of the rearview camera image can reduce the driver's view of what is behind the vehicle, increasing the risk of a crash.
Remedy
Dealers will replace the rearview camera, free of charge. Owner notification letters were mailed October 8, 2025. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 23S48. This recall expands previous recall number 23V-598.
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were repaired incorrectly under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard…
Risk and remedy
Risk
A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
Remedy
Dealers will update SYNC module software, free of charge. Owner notification letters were mailed June 18, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C14.
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to…
Risk and remedy
Risk
A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash.
Remedy
The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco vehicles. The rear shock absorbers may corrode and fail, resulting in detachment of the external reservoir.
Risk and remedy
Risk
An external reservoir that detaches from a vehicle can create a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the rear shock absorbers, as necessary free of charge. Owner notification letters were mailed August 15, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S01.
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco, F-150, Edge, Explorer, Lincoln Nautilus, and Lincoln Aviator vehicles equipped with either a 2.7L or 3.0L Nano EcoBoost engine. The engine intake valves may break while driving, which can result in engine failure and a loss of drive power.
Risk and remedy
Risk
A loss of drive power increases the risk of a crash.
Remedy
Dealers will perform an engine cycle test and replace the engine as necessary, free of charge. Owner notification letters were mailed July 3, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S55.
Ford Motor Company (Ford) is recalling certain 2022-2023 Bronco, 2023 Super Duty F-250, and 2019-2023 Ranger vehicles. The Tire and Loading Information (TREAD) label states the incorrect load carrying capacity, which can result in an overloaded vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard…
Risk and remedy
Risk
An overloaded vehicle increases the risk of a crash.
Remedy
Ford will mail a new TREAD label to install over the existing label, free of charge. Owners will also have the option to take their vehicle to a Ford or Lincoln dealer to have the new label installed, free of charge. Owner notification letters were mailed July 21, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C18.
Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco vehicles built with the 5-Door body style. The first-row seat belt latch plates may be difficult to access from their stowed position. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."
Risk and remedy
Risk
Difficulty accessing the seat belt latches may result in occupants not wearing their seat belts, increasing the risk of injury in a crash.
Remedy
Dealers will add a sliding clip latch stop to the driver and front passenger seat belts, free of charge. Interim owner notification letters notifying owners of the safety risk were mailed July 14, 2023. Owner letters informing owners that parts are available were mailed on October 2, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C16.
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously remedied under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard…
Risk and remedy
Risk
A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
Remedy
The SYNC module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on March 28, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C05.
Ford Motor Company (Ford) is recalling certain 2023 Bronco Wildtrak and 2022 Bronco Raptor vehicles. Internal damage to the steering gear may require increased steering effort or cause the steering wheel to lock-up.
Risk and remedy
Risk
A steering wheel that locks-up can result in a complete loss of steering control, increasing the risk of a crash.
Remedy
Owners are advised not to drive their vehicles until the remedy is performed. Dealers will replace the steering gear, free of charge. Owner notification letters were mailed March 31, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S09.
Ford Motor Company (Ford) is recalling certain 2022-2023 F-150, Mustang, Explorer, Bronco, and 2023 Lincoln Aviator vehicles equipped with automatic transmissions. The transmission may contain a loose bolt which could prevent the transmission from engaging the park gear, although the gear shifter position may indicate that the vehicle has been shifted to…
Risk and remedy
Risk
The inability to secure the vehicle in the park position can result in a rollaway, increasing the risk of a crash or injury.
Remedy
Dealers will inspect and, if necessary, replace the transmissions, free of charge. Owner notification letters were mailed April 25, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S06.
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The right or left side impact sensors may not be properly secured to the vehicle.
Risk and remedy
Risk
An improperly secured side impact sensor may cause the air bags to unintentionally deploy, or not to deploy as intended, increasing the risk of injury in a crash.
Remedy
Dealers will inspect the side impact sensor attachments and repair, as necessary, free of charge. Owner notification letters were mailed January 20, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S77.
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with rearview camera systems and 8-inch screen displays. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Risk and remedy
Risk
A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
Remedy
The SYNC module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on March 25, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22C27.
Ford Motor Company (Ford) is recalling certain 2022 Bronco and Ranger vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach during a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 212, "Windshield Mounting."
Risk and remedy
Risk
A windshield that separates from a vehicle during a crash can increase the risk of injury.
Remedy
Dealers will remove and reinstall the windshield, free of charge. Owner notification letters were mailed July 18, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22C12.
Ford Motor Company (Ford) is recalling certain four-door 2021-2022 Bronco vehicles. The passenger-side rear door may be opened from inside of the vehicle when the child safety lock is in the "ON" position.
Risk and remedy
Risk
A malfunctioning child safety lock increases the risk of injury to a child occupant.
Remedy
Dealers will inspect the passenger-side child safety locks door child safety lock and latch, and replace them, if necessary, free of charge. Owner notification letters were mailed June 28, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S44.
Owner complaints
386 complaints6 involved a crash2 involved a fire4 injuries
What owners report most
Latest complaints
- Electrical system · Seats · Suspension
The contact owns a 2022 Ford Bronco. The contact received notifications of NHTSA Campaign Numbers: 25V025000 (Suspension), 25V721000 (Seats), and NHTSA Campaign Number: 26V468000 (Engine, Electrical System); however, the parts to do the recall repairs were not yet available. The local dealer was…
The contact owns a 2022 Ford Bronco. The contact received notifications of NHTSA Campaign Numbers: 25V025000 (Suspension), 25V721000 (Seats), and NHTSA Campaign Number: 26V468000 (Engine, Electrical System); however, the parts to do the recall repairs were not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The manufacturer was made aware of the issue.
- Structure › Body
The Hardtop on the back is starting to crack and I am afraid that a delamination may cause parts of the top to start flying off causing a road hazard.
- Structure › Body
The vehicle is a 2022 Ford Bronco two-door with a hardtop roof that was previously replaced under a recall due to a defected hardtop roof. After the replacement, I notice stress cracks and delamination around the rear side windows on both sides of the vehicle, including the top and bottom corners…
The vehicle is a 2022 Ford Bronco two-door with a hardtop roof that was previously replaced under a recall due to a defected hardtop roof. After the replacement, I notice stress cracks and delamination around the rear side windows on both sides of the vehicle, including the top and bottom corners, with visible bubbling and separation of the roof material near those window edges. In addition, while driving, there is increased wind noise coming from the roof area, particularly around the T-top panels, which suggests they may not be sealing properly to the main roof. This appears to affect the integrity of the roof system and could be a safety concern if it worsens. I am not aware of a current recall number for this issue. The problem has not yet been confirmed by a dealer or service center. There were no warning messages before it was discovered. The component should be available for inspection if needed.
- Structure › Body
Broncos hard top is cracking and starting to delaminate which could easily cause an accident if this happens dealer said it was out of the 3 year period even though it’s garage kept and still under 26,000 miles ! Feel this should be a recall and addressed being as it’s still happening on new broncos
- Fuel system, gasoline
The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline). Upon contacting the dealer and the manufacturer recently, the contact was informed that the recall repair was previously completed. The contact stated that the vehicle…
The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline). Upon contacting the dealer and the manufacturer recently, the contact was informed that the recall repair was previously completed. The contact stated that the vehicle was never serviced for the recall, and the failure remained present, causing the vehicle to lose power and to stall while driving. The failure mileage was 8,000.
- Steering
Steering assembly failure-Ford service garage diagnosed on 10/13/26. (lower steering shaft and seal). Vehicle was previously seen at the same garage on 10/2/26 and they were unable to reproduce the problem. The vehicle sat for a day or two, then drove fine for a day, but then it became very…
Steering assembly failure-Ford service garage diagnosed on 10/13/26. (lower steering shaft and seal). Vehicle was previously seen at the same garage on 10/2/26 and they were unable to reproduce the problem. The vehicle sat for a day or two, then drove fine for a day, but then it became very difficult to steer again, requiring great effort to turn. Vehicle was taken in on 10/9/26 and driven by shop foreman who confirmed there was an issue. This problem became apparent to us while driving on the interstate when it became extremely difficult to steer, nearly causing a collision. If lane assist is also active and a sudden steer is necessary, the combination of steering assembly problem and fighting the lane assist requires a tremendous amount of strength. There were no warning lamps, messages or other symptoms of the problem prior to the failure
- Fuel system, gasoline
The contact owns a 2022 Ford Bronco. The contact received notification for NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline); however, the part to complete the recall repair was not yet available. The contact stated that the vehicle shuddered on cold starts for up to 10 minutes, and the…
The contact owns a 2022 Ford Bronco. The contact received notification for NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline); however, the part to complete the recall repair was not yet available. The contact stated that the vehicle shuddered on cold starts for up to 10 minutes, and the check engine warning light illuminated while driving at various speeds. The vehicle was taken to the dealer on several occasions, where the check engine warning light was reset; however, the failure recurred. Additionally, messages indicating misfires and a reduced driving time were displayed on the Ford mobile app. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure by phone and confirmed that the remedy was unavailable. The failure mileage was approximately 26,000.
- Unknown or other
Cracking, delamination on top. Leaking near the front windshield when raining. Have saw recalls for these issues on certain models. Not sure why Ford didn't include these models in the recalls since it's doing the exact same thing. This is not a misused or mishandled issue, it is a manufactured defect. Please advise us as to if there is anything going on to fix this situation. Thank you very much.
- Structure › Body
The right rear black plastic fender flair became loose and flew off my car on the highway striking another vehicle. no damage was caused to the other vehicle which was a dump truck. I called a ford representitive about this issue and they seemed to not care at all and told me to take it to…
The right rear black plastic fender flair became loose and flew off my car on the highway striking another vehicle. no damage was caused to the other vehicle which was a dump truck. I called a ford representitive about this issue and they seemed to not care at all and told me to take it to ford and that I have to pay to fix it. meanwhile I looked up recalls and this part was a recalled item. the ford representitive then told my that this recall did not pertain to my vehicle. how IS this allowable? this was emailed to me by ford. here is your case number for your phone call today. [xxx] thank you, [xxx] ford motor company ® EV specialist o: [xxx] ext. [Xxx] information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(B)(6)
- Structure
The contact owns a 2022 Ford Bronco. The contact stated that while washing the vehicle, the contact became aware that the hardtop was delaminated and cracked. The contact associated the failure with NHTSA Campaign Number: 26V299000 (Structure) and Ford GSB Number: 25-7086. The vehicle was taken to…
The contact owns a 2022 Ford Bronco. The contact stated that while washing the vehicle, the contact became aware that the hardtop was delaminated and cracked. The contact associated the failure with NHTSA Campaign Number: 26V299000 (Structure) and Ford GSB Number: 25-7086. The vehicle was taken to the dealer, where the failure was confirmed, and the dealer determined that the vehicle experienced the failure listed in Ford GSB Number: 25-7086. The dealer submitted a claim to the manufacturer; however, the claim was denied because the vehicle did not have warranty coverage or under recall. The failure mileage was approximately 6,300.
- Engine · Power train
My vehicle has had two misfires and the check engine light came on twice. I brought it to quirk ford in Quincy mass and they said ford has not found a solution for this recall which has been years for this recall. My vehicle putters when I start it and has a skunk aroma when I shut it off
- Fuel/propulsion system
When attempting to accelerate from a stopped position to enter loop [XXX] in [XXX]. My vehicle experienced total loss of power due to failure of the low pressure fuel pump. This created a very dangerous situation as I was attempting to enter the highway from the access road. This event very…
When attempting to accelerate from a stopped position to enter loop [XXX] in [XXX]. My vehicle experienced total loss of power due to failure of the low pressure fuel pump. This created a very dangerous situation as I was attempting to enter the highway from the access road. This event very nearly resulted in a crash that could have caused serious bodily injury or death to me. The vehicle was taken to the closest Ford dealership, Red McCombs Ford in [XXX]. The incident was described to the service representative and taken in for diagnosis. The next week, the service representative contacted me to tell me that they were able to replicate the issue in testing and that the low pressure fuel pump had experienced mechanical failure. They said, unfortunately Ford does not have an approved remedy available yet. I told them that I was aware that the failed part was indeed available and had found documented cases where Ford had chosen to approve replacing it for individuals experiencing the same problem. It isn’t a case of a replacement part being available, it is a case of Ford not wanting to replace the failed part and instead attempting to find a software fix that allows for preserving the life of the potentially defective part. However, this is not an acceptable solution once the part has already failed. The service representative stated they were trying to get Ford to authorize the repair, since one is available, but Ford was declining because the had not yet announced an “official recall remedy”. Then I opened a case with Ford Customer Care and they too declined to fix the issue. When I relayed my concern that driving the vehicle would expose me to serious injury or death, they continued to decline. I asked if it was safe to drive and they said “Ford has not issued instructions to stop driving”. Ford is refusing to repair a known safety recall where they are aware of a remedy exists. My Ford Customer Care Case is CXH-09364617-D9H7V8 INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOI
- Fuel/propulsion system
Was driving on highway with cruise control set. Vehicle started slowing down, so pressed on gas pedal and no response from vehicle, had to navigate to shoulder and was unable to drive vehicle. No warning that there was any issue. Vehicle has been at dealership for a month. Low pressure fuel pump failure and no parts are available.
- Power train
Clutch pedal went to floor and didn't return. The accumulator on part # MB3Z-7A512-A failed and broke apart causing a complete loss of brake fluid in the clutch hydraulic system rendering the clutch completely inoperable.
- Structure › Body
I am writing to formally complain about a serious and increasingly concerning problem with the hardtop on my 2022 Ford Bronce four-door. I began noticing cracks in the hardtop after becoming aware of numerous complaints from other Bronco owners regarding similar cracking problems. Once I knew what…
I am writing to formally complain about a serious and increasingly concerning problem with the hardtop on my 2022 Ford Bronce four-door. I began noticing cracks in the hardtop after becoming aware of numerous complaints from other Bronco owners regarding similar cracking problems. Once I knew what to look for, I inspected my Bronco and noticed cracks in the hardtop. I promptly brought the issue to the attention of my Ford dealership. Unfortunately, I was told that the vehicle had just passed the time limit of the factory warranty, even though it was well within the mileage limit of the warranty. I find it extremely frustrating that Ford’s position appears to be based on the calendar expiration of the warranty when this is a known problem (defect) that has been reported by numerous Bronco owners. More importantly, the condition of the hardtop has deteriorated significantly. Over the past several months, the cracks have become substantially worse, and I am now concerned that the hardtop could eventually fail completely. This is no longer simply a cosmetic concern. I purchased a new Ford Bronco with the expectation that the vehicle’s major structural components would remain reliable under normal use. I am requesting that Ford reconsider my case and provide full replacement of the defective hardtop at no cost to me, including parts and installation cost. I would also like Ford to consider the safety implications of allowing a hardtop with progressively worsening cracks to remain in service. I have legitimate concerns that the hardtop could fail at speed or during an accident creating hazard or injury.
- Fuel/propulsion system
Simply filing a complaint for the recall on the fuel pump that still has not been remedied over a year ago. I’m hearing stories of people having to replace their fuel pumps and ford not covering it even though it’s an open recall. Hoping to get more pressure on them to get a remedy. Thank you for all you do!
- Seats
Headrest on rear passenger side will not stay up.
- Electrical system · Fuel/propulsion system · Seats
3 different incidents have came up with recalls that have been going on for awhile this a working vehicle that makes my money to pay for the loans, which for over a year have not made me any money costing me to lose money out of my own pocket, ford has not been willing to work with because it’s a used vehicle and I didn’t barrow money from to purchase this has been going on for more than a year it is ridiculous!!
- Suspension · Wheels
On August 26, 2026, my 2022 Ford Bronco experienced a serious safety related failure while I was driving. The vehicle displayed a sway bar disconnect system warning and became disabled, leaving me stranded on the side of the road. The Bronco had to be towed to a Ford dealership, where it is…
On August 26, 2026, my 2022 Ford Bronco experienced a serious safety related failure while I was driving. The vehicle displayed a sway bar disconnect system warning and became disabled, leaving me stranded on the side of the road. The Bronco had to be towed to a Ford dealership, where it is available for inspection. Ford previously claimed that it inspected my Bronco under a recall specifically pertaining to the sway bar system. Ford determined that the sway bar did not need to be replaced and closed the recall as completed. The vehicle has now experienced a failure involving the same system that Ford claims it previously inspected. I am concerned that the recall inspection may not have identified the problem or that the recall procedure or remedy was insufficient. The precise cause of the current failure is still being diagnosed. Approximately one and a half weeks before the incident, five replacement tires were installed by a mobile tire service. The replacement tires were the same type and size already used on the vehicle. There was no change in tire size and no tire related modification to the Bronco. Three lug nuts were also found loose following this incident. Approximately three months earlier, three lug nuts had come completely off the vehicle. Loose lug nuts were found again during a tire rotation approximately one month before this incident. I do not yet know whether the repeated loose lug nuts and the sway bar system failure are connected. This failure occurred while the vehicle was being driven, disabled the vehicle, and left me stranded. I am requesting that NHTSA document and investigate whether the sway bar recall inspection or remedy was inadequate, or whether another safety defect exists in my 2022 Ford Bronco.
- Unknown or other · Visibility/wiper
Windshield is leaking water/rain inside vehicle. I have it at All American Ford Old Bridge,NJ, for 15 days now and they want to charge me portion $256.76 plus tax. BUt, the Bronco has recall 222c12 or 25C52. I was willing to pay not knowing that there as a recall but they said if it breaks or…
Windshield is leaking water/rain inside vehicle. I have it at All American Ford Old Bridge,NJ, for 15 days now and they want to charge me portion $256.76 plus tax. BUt, the Bronco has recall 222c12 or 25C52. I was willing to pay not knowing that there as a recall but they said if it breaks or cracks or chips while doing work they are not responsible to cover new windshield. please advise. They show on Ford recall website the recall complete, but my windshield was never removed, resealed and reinstalled. So that is a lie/fraud on All American Ford part. Please help. I have 2 other major issues with Bronco as well which are recalls that they made me pay for or did not resolve as of yet. I already paid for a middle roof panel and now front passenger roof panel must be replaced (recall 26S32) and they say it is not part of recall. And, the safety concern is the car just turned off on major highway 2 different episods one in May on NJ Turnpike I was almost hit from behind and the other was on Route 35 in Seaside Park, NJ in August. Same dealership said they can't experience it so they cannot diagnose and repair it. It is the fuel pump/loss of power issue #26V236000. the car has to be restarted and there is no warning. I am very worried about this.
- Structure › Body
Fender flares (2) have detached. Flare 1: Passenger side, front wheel - it flew off while driving. Flare 2: Partially breaking / cracking off - on the drivers side, back wheel.
- Electrical system · Engine · Fuel system, gasoline
The contact owns a 2022 Ford Bronco. The contact received notifications of NHTSA Campaign Numbers: 25V455000 (FUEL SYSTEM, GASOLINE) and 26V468000 (ENGINE, ELECTRICAL SYSTEM); however, the parts to do the recall repairs were not yet available. The local dealer was contacted. The contact stated that…
The contact owns a 2022 Ford Bronco. The contact received notifications of NHTSA Campaign Numbers: 25V455000 (FUEL SYSTEM, GASOLINE) and 26V468000 (ENGINE, ELECTRICAL SYSTEM); however, the parts to do the recall repairs were not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure.
- Engine · Fuel/propulsion system
Loss of power or acceleration randomly, when pressing on the pedal. A recall was issued that it was a fuel pump failure June of 2025. One year and two months later there is still no solution to this recall. I am mostly submitting this covering all bases and am filing a complaint with Ford motor…
Loss of power or acceleration randomly, when pressing on the pedal. A recall was issued that it was a fuel pump failure June of 2025. One year and two months later there is still no solution to this recall. I am mostly submitting this covering all bases and am filing a complaint with Ford motor company as well. This is a serious safety concern as without warning the car basically dies so turning in front of oncoming traffic or pulling out onto a road poses great risk when the vehicle may cease functioning.
- Fuel/propulsion system
There is a manufacture recall for the low pressure fuel pump malfunctioning #25S75/NHTSA#25V455. There has been no action by the manufacturer to remedy this issue in a timely manner. This issue has been ongoing for over 1 year now with no corrective measures.
- Engine · Fuel system, gasoline
The contact owns a 2022 Ford Bronco. The contact stated that while leaving the residence, the vehicle stalled on the highway. The driver was able to avoid a crash with a tractor-trailer. The check engine warning light illuminated intermittently, and a “Service Vehicle Soon” message was displayed.…
The contact owns a 2022 Ford Bronco. The contact stated that while leaving the residence, the vehicle stalled on the highway. The driver was able to avoid a crash with a tractor-trailer. The check engine warning light illuminated intermittently, and a “Service Vehicle Soon” message was displayed. Additionally, there was a tool symbol displayed on the instrument panel. The vehicle was towed to a local dealer, and the contact was informed that the part needed to perform the recall repair of NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline); was not yet available. The manufacturer was not contacted. The failure mileage was approximately 75,000.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Low-pressure fuel pump failure
On July 29, 2024, the Office of Defects Investigation (ODI) opened PE24019 to investigate complaints of low-pressure fuel pump failures in MY 2021 Ford Bronco vehicles. Some consumers reported that the failure occurred without warning while driving, resulting in a complete loss of motive power with no ability to restart…
On July 29, 2024, the Office of Defects Investigation (ODI) opened PE24019 to investigate complaints of low-pressure fuel pump failures in MY 2021 Ford Bronco vehicles. Some consumers reported that the failure occurred without warning while driving, resulting in a complete loss of motive power with no ability to restart the engine. Ford determined that several other vehicle models contain low-pressure fuel pumps substantially similar to the 2021 Ford Bronco, including the 2022-2023 Ford Bronco, 2018-2023 Ford F-150, 2022-2023 Ford Expedition, 2019-2023 Lincoln Navigator, 2020-2023 Ford F-250-F-550, 2024 Ford Super Duty Chassis Cab, 2024-2025 Ford Ranger, 2020-2023 Ford Explorer, 2020-2023 Lincoln Aviator, and 2021-2025 Ford Mustang. ODI's investigation found that the affected vehicles may lose fuel pressure and flow from the fuel delivery module (consisting of a low-pressure fuel pump, jet pump, reservoir, and other parts) due to a low-pressure pump failure. This can cause the engine to stall while driving. The root cause is reduced internal clearance in the fuel pump, increasing friction and sensitivity to vapor lock. Fuel blockage from contamination inside the jet pump also contributed to the failure. Ford stated that the contamination source was unknown. On July 7, 2025, Ford filed recall 25V-455 for certain 2021-2023 Ford F-550 SD/F-450 SD/F-350 SD/F-250 SD, 2021-2022 Lincoln Navigator, 2021-2022 Ford Mustang, 2021-2022 Ford F-150, 2021-2023 Ford Explorer, 2022 Ford Expedition, and 2021-2023 Ford Bronco vehicles produced between July 1, 2021, and July 30, 2022. The recall also included certain 2021-2023 Lincoln Aviator produced between July 1, 2021, and December 21, 2022. Ford explained in its recall filingthat the production dates used for the recall were based on changes in the manufacturing process. Specifically, Ford determined that in June 2021, the supplier modified the jet pump manufacturing process, producing fuel pump chambers with a lower-than-specified internal clearance. In July 2022, the supplier implemented corrective actions to the manufacturing process by adding two additional vacuum pumps to reduce contamination during the production of the jet pump. ODI has identified approximately 1,000 reports involving vehicles covered in this investigation but excluded from recall 25V-455. However, even with such reports, these vehicles experienced comparatively lower failure rates than the vehicles that are subject to Recall 25V-455. Ford has explained that these vehicles were excluded from the recall population because they did not experience the manufacturing changes that prompted the recall. Specifically, according to Ford, vehicles built before July 1, 2021 (the recall production start date), were not affected by the supplier’s change to the jet pump manufacturing process. Even after closing this investigation, ODI will continue to monitor complaints for vehicles excluded from recall 25V-455 to consider whether they exhibit the same risks as the vehicles encompassed by the recall. The recall remedy is currently under development. In view of Ford’s recall action, ODI is closing this Preliminary Evaluation, but will continue to monitor the issue as a remedy is developed and implemented. ODI will take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
- Loss of Motive Power
On July 22, 2022, the Office of Defects Investigation (ODI) granted a Defect Petition (DP22001) and opened a Preliminary Evaluation (PE22007) to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco vehicles equipped with 2.7L EcoBoost engines. Complainants were reporting sudden engine…
On July 22, 2022, the Office of Defects Investigation (ODI) granted a Defect Petition (DP22001) and opened a Preliminary Evaluation (PE22007) to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco vehicles equipped with 2.7L EcoBoost engines. Complainants were reporting sudden engine failure while driving resulting in a loss of motive power, often without the ability to restart. During PE22007, the cause of engine failure and loss of motive power in the subject vehicles was determined to be intake valve fracture, and the full scope of vehicles affected by the subject defect was identified as all MY 2021-2022 Ford and Lincoln models equipped with either the 2.7L or 3.0L EcoBoost engines, referred to as the “Nano” engine family. If an intake valve fractures in the subject engines, it may drop into the cylinder and contact the piston, often resulting in catastrophic engine damage. On September 29, 2023, PE22007 was upgraded to an Engineering Analysis (EA23002) to further investigate the subject defect across the full scope of affected vehicles. During EA23002, ODI visited Ford facilities to review technical information related to intake valve fracture in “Nano” engines, coordinated with NHTSA’s Vehicle Research and Testing Center (VRTC), and analyzed updated field data relating the subject defect. Forensic analysis of fractured intake valves demonstrated that the defective components exhibited “grinding burn” or out of specification hardness in the area of the keeper grooves. The presence of grinding burn is evidence that during the groove grinding phase of production, the temperature of the valve became sufficiently high to alter the microstructure of the material and is indicative that the valve supplier’s manufacturing processes were not within control specifications. Grinding burn results in a hard, brittle microstructure and high residual stresses toward the surface of the valve. Through normal engine loading, a valve with grinding burn will likely fracture at the area of highest vulnerability, which is the third keeper groove. In its response to the EA23002 Information Request (IR) letter, Ford provided evidence of 396 customer complaints (including field reports), 825 warranty claims, and 936 engine exchanges. When considering both ODI and manufacturer failure report data, there have been reports representing 1066 unique vehicles within the subject vehicle population. Analysis of the failure report data demonstrates that vehicles equipped with potentially defective intake valves were built within a production “spike period” of May 2021 – October 2021. The beginning of the spike period corresponds to a ramp up in production at the valve supplier manufacturing facility, and the end of the spike period aligns with the implementation of several mid-production process improvements and the decision to change the metal alloy used to produce intake valves from “Silchrome Lite” to “Silchrome 1”. Ford began investigating the subject defect in July 2021, determined the root cause, and took corrective measures for the new production vehicles. Analysis of the failure report data demonstrates that these corrective actions were successful in eliminating the risk of intake valve fracture for subject vehicles produced after October 2021. However, Ford did not take any field action to address vehicles produced during the spike period, and in the several months following the implementation of the production changes, a significant number of field failures continued to occur. It is Ford’s assessment that not all valves produced during the spike period are defective, and that failures associated with the subject defect occur at low time in service. Analysis of the failure report data demonstrates that the vast majority of failures have occurred before 20,000 miles with over half of all reported failures occurring before 5,000 miles. The rate of reported failures related to the subject defect has steadily decreased since November 2021. ODI coordinated with NHTSA’s National Center for Statistics and Analysis (NCSA) to conduct statistical analysis and predict the number of future failures associated with the subject defect. The results of this analysis, and the trends identified through the failure report data are generally consistent with Ford’s assessment that defective intake valves will likely fail at a low time in service and indicate that the majority of subject vehicles equipped with defective valves have already experienced a failure. On August 23, 2024, Ford submitted recall 24V635 for subject vehicles equipped with “Nano” engines and built within the production spike period identified above (total population 90,736 vehicles). The remedy includes an inspection at a Ford/Lincoln dealership where the lifetime engine cycles of the vehicle will be determined. If a vehicle does not meet a threshold for lifetime engine cycles, the dealership will conduct a high RPM engine cycle accumulation procedure, which aims to identify if the vehicle is equipped with defective intake valves. Any vehicle that fails the accumulation procedure will receive an engine replacement under the recall. In addition to recall 24V635, Ford has stated that it will launch customer satisfaction campaign 24N12, which will provide extended warranty coverage to the subject vehicles through the earlier of 10 years or 150,000 miles. In view of the recall action being taken by Ford, ODI is closing this Engineering Analysis. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11011954Some 2021-2024 Bronco vehicles equipped with a 2.3L/2.7L engine may exhibit a loud front end clink/clunk noise that leads to the identification of a cracked or broken front differential frame mount bracket.
- 11011953Some 2021-2024 Bronco vehicles equipped with a factory subwoofer may exhibit a rattle from right loadspace trim panel at high audio system volumes.
- 11011813Some 2021-2023 Bronco vehicles equipped with a 2.7L EcoBoost engine may exhibit an illuminated MIL with DTC P0456 stored in the PCM.
- 11010950Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs. Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs.
- 11010799Some 2022-2024 Bronco vehicles built on or before 13-Feb-2024 equipped with a 3.0L EcoBoost engine and 2021-2024 Broncos equipped with a 2.3L EcoBoost engine may exhibit an illuminated MIL with ignition system DTCs P0352, P0353, P0354, P0355, P2303, P2306, P2309, P2312, P2304, P2307, P2310, and/or P2313 set in the PCM.
- 11010033Quality Improvements: - Customer should be able to enable and disable Intelligent power toggle button. -Adresses SYNC reboots and improves the vehicle's conectivity with the user's phone
- 11009761Quality improvements include: -Robustness action to enhance the Connectivity, Networking and Cellular Data Services and power management. -Ensuring functionality of Stolen Vehicle Services.
- 11009445Some 2018-2024 F150/Edge, 2018 MKX, 2019-2023 Nautilus, 2020-2025 Explorer/Aviator, 2021-2024 Bronco, and 2024 Ranger vehicles equipped with a 2.7L EcoBoost or a 3.0L EcoBoost engine may exhibit an engine oil leak from the crankshaft rear seal with retaining plate.
- 11009438Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed.
- 11008948While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
- 11008921Some 2021-2024 Bronco vehicles equipped with a factory soft top roof and built on or before 14-Jul-2024 may experience snow or sand accumulation on the vehicles interior during a strong storm with high winds. To correct this condition, follow the Service Procedure to retrofit the soft top assembly.
- 11008702Some 20212024 Bronco and 2024 Ranger vehicles may exhibit a loss of driver's door switch pack control along with any of the following symptoms: * inability to open or close the windows * driver's window switch not working or not working intermittently * cannot fold or unfold the side mirror * cannot adjust the side mirror in any direction * diagnostic trouble code (DTC) B1087:87 stored in the driver's door module (DDM) and/or the passenger door module (PDM) * DTC U2013:23 stored in the DDM and/or PDM
- 11008556"Quality improvements include: -Robustness action to reduce the false window bounce back occurrences"
- 11008223Some 2021-2022 Bronco vehicles equipped with the 2.3L engine may exhibit a red brake warning lamp and brake system warning message in the instrument panel cluster (IPC) with a diagnostic trouble code (DTC) P050F in the anti-lock brake system (ABS) module.
- 11007977Some 2020-2024 Explorer/Aviator/Corsair, 2021-2024 F-150/Bronco, 2023-2024 F-Super Duty, and 2024-2025 Nautilus vehicles may experience the overhead console sunglass bin cannot be locked in a closed position.
- 11007908Some 2021-2024 Bronco may exhibit the upper rail front trim panel with an excessive gap. This may be due to the misalignment of the upper rail front trim panel.
- 1100787220212024 Bronco, 2024 Ranger - Door Window Switch Inoperative With DTC B1087:87 And/Or U2013:23
- 11006879Some 2021-2024 Bronco vehicles may exhibit a rattle from the front windows with the windows placed in the partially down position and driving over rough roads and/or bumps.
- 11006779This article supersedes 24-2186 to update the model years affected. Some 2021-2023 Bronco vehicles equipped with a factory soft top roof may exhibit a headliner that is detaching from the soft top material. This may be due to the factory installation process. To correct this condition, follow the Service Procedure to reattach the headliner or replace the soft top roof material.
- 11006443Some 2020-2024 F-150, 2021-2024 Bronco, and 2024 Ranger vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a stuck internal component of the variable cam timing (VCT) unit.
- 11005837Some 2021-2024 Bronco/F-150 (non-Lightning) vehicles may exhibit a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is fully operational and there are no diagnostic trouble codes (DTC) stored related to the charging system. This may be due to the customer using an aftermarket programmer to change body control module (BCM) configuration.
- 11005698Some 2021-2024 Bronco vehicles may require servicing of the interior door handle lock cable mounting bracket on the interior door handle. The interior door handle cable mounting bracket, base part number 78219A64 (right) and 78219A65 (left), are now available to service separately from the cables and latch mechanisms. It is no longer necessary to replace the complete latch assembly for a damaged interior door handle lock indicator mounting bracket.
- 11005694Some 2021-2024 Bronco vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC)s P0096 and/or P007B stored in the powertrain control module (PCM) which may be more prevalent in high ambient air temperatures. For vehicles that meet this criteria, inspect the front of the vehicle for the presence of an aftermarket bumper and/or accessories which may restrict air flow to the charge air cooler and surrounding sensors. Remove the aftermarket accessory and return the vehicle to stock and reevaluate. If the concern returns with the stock bumper/accessories removed, proceed to normal Workshop Manual diagnostics.
- 11003144Some 2021-2024 F-150/Bronco and 2023-2024 Escape/F-Super Duty vehicles built with SYNC 4 require a connected phone with Android Auto or Apple CarPlay active to enable voice interactions and use of the steering wheel voice control button. This is due to the affected vehicles not having built in voice interactions capability. Vehicles with built in voice interaction capability can be identified as also being equipped with the built in connected navigation feature which includes a navigation tab on the center display screen. Diagnostics should only be performed for voice interactions on vehicles equipped with built in voice interaction capability or with Android Auto or Apple CarPlay active.
- 11001584This article supersedes 24-2080 to add 2024 model year vehicles. Some 2021-2024 Bronco vehicles equipped with a factory soft top roof may exhibit a headliner that is detaching from the soft top material. This may be due to the factory installation process. To correct this condition, follow the Service Procedure to reattach the headliner or replace the soft top roof material.
- 11001112Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.
- 11000933Quality improvements include: -Addresses SYNC reboot issue may occurs after 2 hours of continuous use. -Adds a "some display features may be temporarily unavailable" message to the SYNC screen when a SYNC update is installing. -Vehicle Enhancement: Software Updates currently has the title Recurring Update Schedule in Setting, Tittle will change to Reccuring Schedule
- 11000848'Quality improvements include: -Fix the vehicle battery drain issue due to the Key-Off Load caused by the Instrument Cluster Panel staying on.
- 11000555Some 2021-2024 Bronco vehicles may exhibit paint wearing along on the top inner edge of the tailgate where the rear window weather strip contacts the tailgate. This may be due to the accumulation of dirt between the rear window seal and tailgate. Inform customers that engineering is aware of this condition and is currently working on a solution which is expected in Q3 2024. Schedule a service visit for customers when the repair is available in Q3 2024. Monitor OASIS for additional information.
- 11000299Some 2021-2024 Bronco vehicles equipped with a factory soft top roof may experience snow or sand accumulation on the vehicles interior during a strong storm with high winds. Inform customers that repair kits are currently on backorder and are expected to be available Q3 2024. Schedule a service visit for customers when the repair is available in Q3 2024. Monitor OASIS for additional information.
- 10254319Quality improvements include: -Fix the infrequent random audio noises issue and improve the audio quality of the vehicle
- 10254159Some 2021-2023 Bronco vehicles equipped with a 2.7L or 3.0L engine may exhibit an illuminated MIL with DTC P25B4, P25B6, and/or P0299 stored in the powertrain control module (PCM). This may be due to a loose nut on the turbo actuator arm causing an under boost condition
- 10254138All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
- 10254136Some 2021-2024 Bronco vehicles may experience a repeat loss of window initialization which results in a loss of short drop and/or one-touch up and one-touch down feature operation. This may be due to a recent short drop enhancement that is contained in the driver door module (DDM) and passenger door module (PDM) software. To correct this condition, update the DDM and PDM to the latest software levels then download and run the Loss Of Power Window Initialization Concern application using Ford Diagnosis and Repair System (FDRS). When prompted by the application for a password, use DSPWR-308. If the vehicles DDM and PDM had software part numbers ending with CN or CR when it arrived, advise the customer that the vehicle will no longer exhibit a short drop event to all door windows anytime the vehicle is unlocked using the remote keyless entry (RKE), accessory keyless entry keypad, or the interior door unlock switch.
- 10254122Some 2020-2024 F-150 and 2021-2024 Bronco vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a stuck internal component of the variable cam timing (VCT) unit. To correct the condition, replace all 4 of the VCT units following Workshop Manual (WSM), Section 303-01. For claiming, use causal part 6C525 and applicable labor operations in Section 6 of the Service Labor Time Standards (SLTS) Manual. If labor times are not available, claim M-time.
- 10253892Some 2022-2024 Bronco Raptor vehicles may exhibit an intermittent no crank/no start/discharged battery due to the presence of a parasitic battery drain. This may be due to the instrument panel cluster (IPC) software.
- 10253890This article supersedes TSB 23-2400 to update the parts list. Some 2021-2023 Bronco vehicles may encounter a Sta-bar Disconnect Service Required message in the instrument panel cluster and an illuminated warning light with diagnostic trouble codes (DTCs) stored in the chassis control module (CHCM)
- 10253552Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
- 102526282021-2023 Bronco vehicles built on or before 9-Jul-2023 may have new version software in their driver door module (DDM) and passenger door module (PDM) that contains noticeable enhancements to the window short drop operation. This software level can be identified in the DDM and PDM as Software Part Number MU5T-14C064-CR or later. This software was released via a software update delivered over-the-air (OTA) starting in September 2023 if the vehicle's connectivity was enabled in the vehicle settings. Vehicles with this new software will exhibit a short drop event to all door windows anytime the vehicle is unlocked using the remote keyless entry (RKE), accessory keyless entry keypad, or the interior door unlock switch. The short drop function will return to the UP position when a lock input is received from these same inputs. For vehicles equipped with passive entry, a short drop event will not activate when a door is unlocked by placing a hand on an exterior door handle. 2023-2024 Bronco vehicles built on and after 10-Jul-2023 received this software from the factory.
- 10252616Some 2021-2023 Bronco vehicles equiped with a 2.7L engine may exhibit an ilumintated MIL with DTC P0456 stored in the powertrain control module (PCM). This may be due to the software level of the PCM and has no effect on vehicle operation.
Every Ford Bronco model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.