2026 Ford Bronco
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Ford › Bronco › 2026
These records cover every 2026 Ford Bronco. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
9 recalls name the 2026 Ford Bronco. Newest first.
Ford Motor Company (Ford) is recalling certain 2026 Bronco vehicles. The mounting bracket on the right-hand-side side curtain air bag may have a metal burr that can tear the air bag during deployment.
Risk and remedy
Risk
A torn air bag may fail to properly restrain an occupant during a crash, increasing the risk of injury.
Remedy
Dealers will increase the space between the bracket and air bag to remove the contact condition, free of charge. Owner notification letters were October 16, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S64. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on September 10, 2026.
Ford Motor Company (Ford) is recalling certain 2026 Explorer, Bronco, Bronco Sport, Mustang, and Ranger vehicles. The engine piston domes may have been manufactured incorrectly, which can result in piston dome failure and lead to a loss of drive power.
Risk and remedy
Risk
An unexpected loss of drive power increases the risk of a crash.
Remedy
Dealers will inspect the engine pistons and replace the engine long block, if necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed September 3, 2026. Additional letters will be sent once the remedy is available, anticipated in December 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S61. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on August 28, 2026.
Ford Motor Company (Ford) is recalling certain 2021-2026 Bronco and Bronco Raptor vehicles. The engine compartment wiring harness may become damaged and short circuit.
Risk and remedy
Risk
A short circuit in the engine compartment can create heat or spark, increasing the risk of a fire.
Remedy
Dealers will install sheathing over the wiring, free of charge. This is a Phased campaign. Phase 1 will include 2026 Bronco Raptor notified owners on 7/31/2026. Phase 2 will include 2021-2025 Bronco Raptor vehicle will notify owners on or about 8/14/2026. Phase 3 will include 2021-2026 Bronco will notify owners on or about 9/1/2026. Owner notification letters were mailed August 5, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S55. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on July 23, 2026.
Ford Motor Company (Ford) is recalling certain 2022-2026 Bronco vehicles. The fender flares may not be properly secured and detach from the vehicle.
Risk and remedy
Risk
A detached fender flare can become a road hazard and increase the risk of a crash.
Remedy
Dealers will inspect and repair, or replace the fender flares as necessary, free of charge. Owner notification letters were mailed September 1, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S47. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning August 7, 2026.
Ford Motor Company (Ford) is recalling certain 2025-2026 Explorer, Ranger, and Bronco vehicles. The engine may fail, which can result in a loss of drive power.
Risk and remedy
Risk
A sudden loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the engine long block, free of charge. Owner notification letters were mailed October 23, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S35. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on May 28, 2026.
Ford Motor Company (Ford) is recalling certain 2026 Ranger and Bronco vehicles. The vehicle specifications listed on the tire placard and safety certification labels may be incorrect, including the VIN, capacity weight, seating capacity, front and rear gross axle weight rating (GAWR), tire and rim dimensions, and recommended cold tire pressure. As such…
Risk and remedy
Risk
The incorrect tire size, tire pressures, and GAWR listed on the labels can allow the vehicle to be overloaded or have improperly inflated tires, increasing the risk of a crash.
Remedy
Dealers will inspect and if necessary, replace the certification and TREAD labels, free of charge. Owner notification letters were mailed June 3, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26C24. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on May 28, 2026.
Ford Motor Company (Ford) is recalling certain 2024-2026 Ranger and Bronco vehicles. The front seats may have a loose or dislodged seat frame height-adjust pivot bolt.
Risk and remedy
Risk
A seat with a dislodged bolt may not properly restrain an occupant in a crash, increasing the risk of injury.
Remedy
Dealers will inspect and replace the pivot links and bolts as necessary, free of charge. Owner notification letters were mailed May 22, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford’s number for this recall is 26S30. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov beginning April 30, 2026.
Ford Motor Company (Ford) is recalling certain 2021-2026 Ford Bronco and 2021-2024 Ford Edge vehicles. The Accessory Protocol Interface Module (APIM) may overheat and shutdown, which can prevent the rearview camera image from displaying as intended.
Risk and remedy
Risk
A rearview camera that fails to display an image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.
Remedy
The APIM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed April 13, 2026. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 26S09. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on March 5, 2026.
Ford Motor Company (Ford) is recalling certain 2025-2026 Bronco and Bronco Sport vehicles. The Instrument Panel Cluster (IPC) may fail at startup.
Risk and remedy
Risk
An instrument panel display that does not show critical information, such as warning lights or vehicle speed, increases the risk of a crash.
Remedy
The instrument panel cluster software will be updated by a dealer or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed December 4, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SC3.
Owner complaints
11 complaints1 involved a crash
What owners report most
Latest complaints
- Steering
I have a new bronco with 3,000 miles on it and I used my heated steering wheel for the first time today and the cabin started filling up with smoke. The smoke was coming from the steering column. I’m not sure if something was on fire or just smoking but I didn’t see flames just a lot of smoke. I have a video. Where can I email it?
- Structure › Body
Hardtop is cracking already. Was built in June of 2026 and purchased in August of 2026. Top needs replacement already. Looked on the dealer lot and every new and used bronco with the M.I.C top had cracks like mine or worse.
- Power train
Twice, while flat towing the 2026 Ford Bronco something happen and allegedly the neutral tow disabled and I had to replace the transmission. $7,500 each time. The first time the Bronco had 900 miles and the second time the unit had 3,000 miles. Both times the warranty claim was denied. Ford blamed…
Twice, while flat towing the 2026 Ford Bronco something happen and allegedly the neutral tow disabled and I had to replace the transmission. $7,500 each time. The first time the Bronco had 900 miles and the second time the unit had 3,000 miles. Both times the warranty claim was denied. Ford blamed it on a battery voltage drop which in turn disabled the neutral tow. I can not find anywhere in the manual where it says the battery voltage level can not fall below a certain level. Can you help I will upload the first transmission invoice. The unit is currently in the shop getting the second transmission installed. The price is the same as the first.
- Structure › Body
Vehicle front passenger wheel well flare detached while driving narrowly avoiding impact to other vehicles on the road. After recovering the part noticed front driver wheel well flare starting to detach. Safety clips appeared intact as if they never locked in place.
- Visibility
The contact owns a 2026 Ford Bronco. The contact stated that while driving approximately 70-75 MPH in the left lane on the interstate on a sunny day, near the grass, the driver's side rear window exploded without impact. The local dealer was contacted, but the vehicle was not diagnosed or repaired.…
The contact owns a 2026 Ford Bronco. The contact stated that while driving approximately 70-75 MPH in the left lane on the interstate on a sunny day, near the grass, the driver's side rear window exploded without impact. The local dealer was contacted, but the vehicle was not diagnosed or repaired. Another local dealer, Hagerstown Ford Service (1714 Massey Blvd, Hagerstown, MD 21740), was contacted and was able to replace the glass. A warranty claim was filed but was later denied. The manufacturer was contacted and determined that the failure was caused by an unidentified object and declined the claim. The failure mileage was approximately 735.
- Structure › Body
While driving on the roadway at approximately 5,841 odometer miles, the vehicle's fender moulding/flare clip retention failed, causing the moulding to loosen and completely detach from the vehicle. The detached fender moulding separated in transit, creating an immediate road debris hazard for…
While driving on the roadway at approximately 5,841 odometer miles, the vehicle's fender moulding/flare clip retention failed, causing the moulding to loosen and completely detach from the vehicle. The detached fender moulding separated in transit, creating an immediate road debris hazard for surrounding traffic and trailing motorists. The detached component was recovered with cosmetic surface damage and taken to an independent repair facility for repair and repainting. The component and vehicle remain available for inspection upon request. Prior to detachment, there were no interior warning lamps or messages displayed. The failure matches the defect condition identified under NHTSA Safety Recall Campaign 26V403 (Ford Manufacturer Recall 26S47). The manufacturer's customer support center was contacted to report the failure and seek pre-remedy out-of-pocket repair reimbursement under federal recall guidelines. The manufacturer stated that no reimbursement review or escalation could proceed because the official recall remedy status remains 'Remedy Not Available' (anticipated September 2026), leaving the vehicle owner without a remedy or immediate reimbursement pathway after experiencing the safety failure.
- Seat belts
Seat beat created a laceration on arm with normal use.
- Power train
The contact owns a 2026 Ford Bronco. The contact stated that while driving at approximately 10 MPH and depressing the accelerator to make a left turn, the vehicle failed to accelerate as intended. The transmission shifted into neutral, and the vehicle coasted forward. The contact pulled over to the…
The contact owns a 2026 Ford Bronco. The contact stated that while driving at approximately 10 MPH and depressing the accelerator to make a left turn, the vehicle failed to accelerate as intended. The transmission shifted into neutral, and the vehicle coasted forward. The contact pulled over to the side of the road and activated the hazard lights. The system was reset, and the vehicle was able to accelerate. There were no warning lights illuminated. The vehicle was taken to the dealer, who was unable to duplicate or determine the cause of the failure. The vehicle was not repaired. The manufacturer was not made aware of the failure; however, the dealer contacted the manufacturer and confirmed the dealer's decision of the dealer. The failure mileage was approximately 617.
- Electrical system · Engine · Seats
Description On your vehicle, it may be possible that one or more engine camshaft roller finger followers were not properly installed at the time of engine assembly. Safety Risk An improperly installed engine camshaft roller finger follower may result in engine failure, resulting in a no-start…
Description On your vehicle, it may be possible that one or more engine camshaft roller finger followers were not properly installed at the time of engine assembly. Safety Risk An improperly installed engine camshaft roller finger follower may result in engine failure, resulting in a no-start condition or a loss of motive power. A loss of motive power increases the risk of a crash. Your vehicle may also experience engine ticking or tapping noise, and or a low-volume oil leak due to this condition. Remedy A remedy is not yet available. Ford Motor Company is working to provide parts for this repair. When the remedy becomes available, Ford Motor Company will notify you via mail to schedule a service appointment with your dealer for repairs to be completed free of charge. The remedy is anticipated to be available 4TH quarter of 2026. Next Steps Contact your dealer for more information to schedule the free service. NOTE: Recall service not available right now. We have a remedy but parts are not available right now. We will inform you when the service is available. Or, you can contact your dealer.
- Electrical system
The 2026 Ford Bronco Outer Banks instrument cluster has gone blank on two occasions (4/3/26 and 4/23/29). The first time the service department at Joe Mahan Ford, Paris, TN reported the display returned when connected to thier computer, but kept the Bronco for several days trying to replicate the…
The 2026 Ford Bronco Outer Banks instrument cluster has gone blank on two occasions (4/3/26 and 4/23/29). The first time the service department at Joe Mahan Ford, Paris, TN reported the display returned when connected to thier computer, but kept the Bronco for several days trying to replicate the condition. I returned it to the dealer for the same fault on 4/27/26 and it is still in the shop. With the Cluster blank the gauges, speedometer, cruise control, lane warning and assist are not operational. Speed limit and travel speeds are visible on the Car Play navigation screen. I’ll update this complaint upon dealer release.
- Unknown or other
Summary of the Safety Problem: A 2026 Ford Bronco rolled out of its parked position with no occupants, despite being left in Park, and collided with another vehicle. Full Description of the Incident: The Ford Bronco was placed in Park, was not running, and had no occupants. I exited the vehicle…
Summary of the Safety Problem: A 2026 Ford Bronco rolled out of its parked position with no occupants, despite being left in Park, and collided with another vehicle. Full Description of the Incident: The Ford Bronco was placed in Park, was not running, and had no occupants. I exited the vehicle several times to reinstall the removable roof panels. The vehicle remained stationary during this process. After completing the roof panel installation, my wife and I closed the doors and trunk and we walked toward the building. A witness (the owner of the other car that was involved in car collision ) confirmed that the Bronco was still parked where we left it. A short time later, we learned that the Bronco had rolled out of its parking spot and struck a parked car. The Bronco had not been touched, driven, or moved by anyone after we walked away that we were aware of. There were no warning signs that we were aware of. The police were at the scene and filed a report. This was a Enterprise Car Rental Vehicle with approx. 1,300 miles. I am unsure if this vehicle has been inspected by Enterprise. Damage / Injuries: •Collision with a parked car. •No injuries reported. •Police report filed (attached). •Photos available (attached). Why This Is a Safety Defect: A vehicle that rolls away while in Park violates the intent of Federal Motor Vehicle Safety Standard (FMVSS) 114, which aims to prevent accidental rollaway. This Bronco should not have moved under any circumstances once placed in Park. What You Request NHTSA to Investigate: •Whether the 2026 Ford Bronco has a defect in its Park mechanism, parking brake system, or electronic controls that can cause unintended rollaway. •Whether similar complaints exist for this model year. •Whether a recall or inspection campaign is warranted to prevent future incidents. Attachments Included: •Police Accident Report •Photos of vehicle positions and damage •Rental agreement
Every Ford Bronco model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.