2002 Hummer H2

Owner complaints

What owners report most

1. Visibility2
2. Power train1

Latest complaints

• Jun 12, 2012FL
  Visibility › Windshield wiper/washer · Visibility › Windshield wiper/washer › Motor

  2003 hummer H2. Consumer writes in regards to reimbursement for windshield wiper recall *tgw the wiper blade motor was replaced. *Jb

• Dec 14, 2011MO43,000 mi
  Power train
  TL* the contact owns a 2003 H2 hummer. while driving 1 mph, the front passenger side wheel fractured and detached from the vehicle. the dealer informed the contact that the driveshaft and spindle were fractured, as well as the casing behind the wheel. the contact was awaiting repairs to the…

  TL* the contact owns a 2003 H2 hummer. while driving 1 mph, the front passenger side wheel fractured and detached from the vehicle. the dealer informed the contact that the driveshaft and spindle were fractured, as well as the casing behind the wheel. the contact was awaiting repairs to the vehicle. the manufacturer was not notified of the failure. the current and the failure mileages were 43,000. the vin was unavailable.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11006621Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
• 11004761This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
• 11004557This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
• 11002312This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
• 10252735This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
• 10252163XM Audio Traffic And Travel Link Availability And Operation.
• 10251890This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
• 10250775This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
• 10249579This PI bulletin advises the technician on the proper way to install the pistons in an engine.
• 10249011This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
• 10248444Vehicle Recalls
• 10247681Information On Requests To Add OnStar Bluetooth Option.
• 10246952Programming And Activation Of Replacement OnStar Modules.
• 10246951Programming And Activation Of Replacement OnStar Modules.
• 10246631Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules
• 10245951Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
• 10245950Canadian Customers Unable To Place Calls In The United States
• 10244274This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
• 10244201This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
• 10242262This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
• 10235802This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
• 10235799This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
• 10234141This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
• 10234110This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10232287This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
• 10232136This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
• 10227056This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
• 10224820This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
• 10222796This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10214869This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10209980This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
• 10209921This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10190934Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
• 10190933Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
• 10190932Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
• 10190931Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
• 10190512OnStar Voice Fallback Number Update Some customers may have received a letter from OnStar stating that "We recently tried to provide a software update to the OnStar hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."
• 10189005This SKU is a Climate Control Module. The customer communication requested return of unsold inventory to inspect for a software issue. If the software issue exists it can cause a fan in the climate control system to stay on even when the ignition is turned off. The fan staying on even though the ignition is off can drain the battery, making the vehicle unable to start.
• 10176607This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
• 10083900This preliminary information communication advises the technician, if unable to place an onstar call in the ignition on mode after the onstar canada upgrade to contact the gm technical assistance center onstar group for further assistance.

Every Hummer H2 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.