Navistar, Inc. (Navistar) is recalling certain 2016-2017 International TranStar, 2017-2019 International ProStar, International LoneStar, 2017-2020 International DuraStar, WorkStar, and 2018-2019 IC Bus HC Commercial buses. The heating, ventilation, and air-conditioning (HVAC) blower motor circuit may have an insufficient wiring terminal that can overheat.
Risk and remedy
Risk
An overheated electrical circuit can increase the risk of a fire.
Remedy
Dealers will replace the HVAC blower motor load circuit wiring terminal, free of charge. Owner notification letters are expected to be mailed June 5, 2023. Owners may contact Navistar's customer service at 1-800-448-7825. Navistar's number for this recall is 23510.
Navistar, Inc. (Navistar) is recalling certain 2019-2021 International MV, 2020-2021 International HV, 2014-2020 International DuraStar and 2015-2018 International WorkStar vehicles. When the parking brake is applied and the automatic transmission is still in the drive or reverse position and the stationary PTO switch is engaged by the operator, the engine…
Risk and remedy
Risk
Unexpected Vehicle movement can increase the risk of a crash or injury.
Remedy
Navistar will notify owners, and dealers will update the parameters in the Cummins ECM for feature codes 12VXT or 12VXU that enables the PTO neutral interlock, free of charge. The recall began February 17, 2021. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for this recall is 20510.
Navistar, Inc. (Navistar) is recalling certain 2017-2020 International WorkStar and International DuraStar, 2018-2019 IC 1300 FBC Commercial and IC HC Commercial, 2018-2021 IC CE Commercial, International MV and International HV, and 2019-2021 IC TC Commercial buses with Cummins B6.7 diesel engines with a fuel module option number FS90301 or FS90453. The…
Risk and remedy
Risk
A fire increases the risk of injury. An engine stall can increase the risk of a crash.
Remedy
Cummins will notify the affected Navistar customers and dealers will disable the fuel heater by either installing a plug in place of the heater or otherwise rendering the fuel heater inoperable and removing the fuse supplying electrical power to the fuel heater and installing a cover over the wire harness connector, free of charge. The recall began May 28, 2020. Owners may contact Cummins customer service at 1-800-286-6467.
Custom Fab & Body LLC (Custom Fab & Body) is recalling certain 2018 Ford F-650 XLT Crew Cab, 2017-2018 International 7500 4x4, and 2018 International 7500 4x2, Freightliner M2-112 and M2-106, and Kenworth T-370-based emergency vehicles equipped with Whelen brake lights. Depending on the specific wiring of the vehicle, these brake lights may illuminate when…
Risk and remedy
Risk
If the brake lights incorrectly illuminate, it can confuse other drivers, possibly increasing the risk of a crash.
Remedy
Custom Fab & Body has notified owners, instructing them to contact Whelen for replacement lights, free of charge. The recall began April 11, 2019. Owners may contact Whelen customer service at 1-860-526-9504.
Navistar, Inc. (Navistar) is recalling certain 2017-2020 International DuraStar and WorkStar, 2018-2020 IC Bus CECB, International HV and MV, 2018-2019 IC Bus 1300 FBC and HCCB, and 2019-2020 IC Bus TCCB vehicles equipped with Cummins B6.7 diesel engines with fuel module option number FS90301 or FS90453. The electric fuel heater within the fuel module may…
Risk and remedy
Risk
A fire increases the risk of injury. An engine stall can increase the risk of crash.
Remedy
Cummins will notify the affected Navistar owners. Cummins dealers will replace the fuel heater with a newly designed fuel heater, free of charge. The recall began May 2, 2019. Owners may contact Cummins customer service at 1-800-286-6467 or Navistar customer service at 1-800-448-7825.
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
11010428This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
10253970This document details the procedure that must be followed to ensure proper alternator troubleshooting.
10251414Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine.
10251409Suggested alignment target values when performing a vehicle axle alignment.
10246231J1939 Data Link Source Address Information
10244926Rebuilding Cylinder Heads on Certain MaxxForce 11/13, N13, and A26 engines; 2010 to present.
10243610How to request a horsepower quote; all International and Cummins engines
10243594Certain International N13 engines may be noncompliant to the required On Board Diagnostics (OBD) Monitor, Manufacturers Self-Test (MST) for over-boost, Exhaust Gas Recirculation (EGR) low flow, and EGR high flow monitors. Under certain conditions, this noncompliance may result in the failure to detect an increase in regulated air pollutants.
10241555J1939 Data Link Source Address Information
10241554J1939 Data Link Troubleshooting
10240193Snap-On torque wrench requirement for all big bore engine connecting rod bolts; A26, MaxxForce 13, N13 engines
10238858QLS Emergency Calibration Revert Process
10237468New air compressor incorporates an oil feed dowel O-ring. Only models equipped with 2010 and newer MaxxForce 11/13 engines, all N13, and A26 engines
10237462QLS Emergency Calibration Revert Process
10237447Per agreement with EPA and CARB, Cummins, Inc. provided an emergency calibration for Cummins ISB, B6.7, ISL9, L9, and X15 engines when a DEF Quality Sensor (DQS) was not available. This action addressed the Diesel Exhaust Fluid (DEF) Quality Sensor failures in the field and the unavailability of parts due to the worldwide chip shortage. This recall is step two of this program designed to revert all affected vehicles back to the certified calibration and to provide them with the latest improved DQS and Coolant Control Valve (CCV) designs. Additionally, the emergency calibration and the restoration to the certified calibration with the latest improved DQS and Coolant Control Valve (CCV) designs have no effect on vehicle Emissions.
10236042New Air compressor Incorporates an oil feed dowel O-ring; only models built with MaxxForce 11/13, N13, or A26 Engines
10234021Rebuilding cylinder heads on certain EPA 2010 MaxxForce 11/13, N13, and A26 Engines
10234015Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
10234007Telematics installation guidelines - Only units with 500K data link
10234000Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI engines or Cummins ISB engine with Allison transmissions
10232616Rebuilding Cylinder Heads on Certain International MaxxForce 11/13 engines and all International N13 and A26 engines
10231068QLS Emergency ECM Calibration; only models equipped with Cummins B6.7, X15, L9, or International A26 engines
10227455J1939 Data link source address information
10227446QLS Emergency Calibration. applies to 2016 and newer Cummins B6.6, X15, and L9 engines and all A26 engines