2022 International Workstar
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › International › Workstar › 2022
These records cover every 2022 International Workstar. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
1 recall names the 2022 International Workstar. Newest first.
Navistar, Inc. (Navistar) is recalling certain 2022-2023 International HX, HV, LoneStar, LT, MV, RH, IC TC Commercial Bus, and 2022 International WorkStar vehicles. The steering gears may have been assembled incorrectly, which can cause the gear to fracture.
Risk and remedy
Risk
A fractured steering gear can cause a loss of steering control, increasing the risk of a crash.
Remedy
Dealers will inspect the steering gear serial numbers, and replace the steering gears as necessary, free of charge. Interim owner notification letters were mailed August 18, 2022. Remedy parts are expected to become available in mid-October 2022. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for this recall is 22513.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010428This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
- 11008349This article is intended to provide information for how to program International Engines that have been sold to another company and installed in a chassis that does NOT have an International VIN Number. This may include Detroit Series 40 engines, Perkins, Street Sweepers, Cranes, Fire Trucks, Generators, Blower motors, and more.
- 10251414Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine.
- 10251409Suggested alignment target values when performing a vehicle axle alignment.
- 10246231J1939 Data Link Source Address Information
- 10244926Rebuilding Cylinder Heads on Certain MaxxForce 11/13, N13, and A26 engines; 2010 to present.
- 10243610How to request a horsepower quote; all International and Cummins engines
- 10243601Cummins B6.7 Grid Heater Relay
- 10243596General Wheel Speed Sensor Troubleshooting
- 10243595Diagnosis of chassis wander complaints.
- 10241555J1939 Data Link Source Address Information
- 10241554J1939 Data Link Troubleshooting
- 10240193Snap-On torque wrench requirement for all big bore engine connecting rod bolts; A26, MaxxForce 13, N13 engines
- 10238858QLS Emergency Calibration Revert Process
- 10237468New air compressor incorporates an oil feed dowel O-ring. Only models equipped with 2010 and newer MaxxForce 11/13 engines, all N13, and A26 engines
- 10236042New Air compressor Incorporates an oil feed dowel O-ring; only models built with MaxxForce 11/13, N13, or A26 Engines
- 10234021Rebuilding cylinder heads on certain EPA 2010 MaxxForce 11/13, N13, and A26 Engines
- 10234015Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
- 10234007Telematics installation guidelines - Only units with 500K data link
- 10234000Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI engines or Cummins ISB engine with Allison transmissions
- 10232616Rebuilding Cylinder Heads on Certain International MaxxForce 11/13 engines and all International N13 and A26 engines
- 10231068QLS Emergency ECM Calibration; only models equipped with Cummins B6.7, X15, L9, or International A26 engines
- 10227455J1939 Data link source address information
- 10227446QLS Emergency Calibration. applies to 2016 and newer Cummins B6.6, X15, and L9 engines and all A26 engines
- 10225616The steering gears may have been assembled with less than the required input shaft ball bearings and can result in a fracture of the input shaft and loss of steering.
- 10222490Pico Scope CCOS (Crankcase Separator Test)
- 10222479As reported by R. H. Sheppard Co., Inc. in their defect report to NHTSA (Recall 22E-047), steering gears were assembled with fewer than the required number of recirculating balls which can lead to a fracture in the steering gear worm-shaft and loss of vehicle steering.
- 10219330PicoScope Test One Channel RCT
- 10219328PicoScope Wheel Speed Sensor Test
- 10219325PicoScope Test Resistance and Ohmmeter
- 10219319PicoScope Test for Datalink (CAN) Health Shorts & opens
- 10219314PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
- 10219308PicoScope Test 12V Electrical Noise Detection
- 10219307PicoScope Test 5V & 12V Intermittent Open and Short circuit diagnostics
- 10215245Front cab mount bushings/insulators MV, HV, DuraStar, and WorkStar vehicles used in severe vocations
- 10215243Cab water leak trouble shooting tips
Every International Workstar model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.