2017 Mazda CX-3
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mazda › CX-3 › 2017
These records cover every 2017 Mazda CX-3. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
1 recall names the 2017 Mazda CX-3. Newest first.
Mazda North American Operations (Mazda) is recalling certain 2014-2018 Mazda3 and 2016-2021 CX-3 vehicles. The rearview camera image may not display properly by showing a flickering or distorted image.
Risk and remedy
Risk
A rearview camera that does not display properly can reduce the driver's rear view, increasing the risk of a crash or injury.
Remedy
Dealers will inspect and replace the rearview camera, as necessary. In addition, dealers will install a wiring harness fastening seal. All repairs will be performed free of charge. Interim notification letters, notifying owners of the safety risk, were mailed September 13, 2023. Final owner letters for affected models and model years in the states of CT, MA, MD, NJ, NY, PA and VA were mailed August 14, 2024. The remaining owner notification letters will be mailed at a future date, anticipated on or before May 1, 2025. Owners may contact Mazda customer service at 1-800-222-5500, Option 6. Mazda's number for this recall is 6023G.
Owner complaints
21 complaints2 involved a crash
What owners report most
Latest complaints
- Visibility/wiper
Windshield wiper fluid tank leaks when you pour fluid in empty within about an hour
- Vehicle speed control
LED speedometer in dash showing incorrect speed or unreadable. Advised of chip malfunction.
- Steering
Steering system seems to become unhinged. Something in the steering system is not working properly.
- Back over prevention
The contact owns a 2017 Mazda CX-3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact…
The contact owns a 2017 Mazda CX-3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated that the camera image was distorted while in use. The failure mileage was unknown. VIN tool confirms parts not available.
- Unknown or other
When starting the car in cold weather, the driver assistance system, to include rear camera display, navigation, hands-free voice commands and calling, continuously restarts for close to 15 minutes rendering safe navigation unavailable. Without a backup navigation system, drivers cannot get turn…
When starting the car in cold weather, the driver assistance system, to include rear camera display, navigation, hands-free voice commands and calling, continuously restarts for close to 15 minutes rendering safe navigation unavailable. Without a backup navigation system, drivers cannot get turn prompts and safely plan for the next exit or turn. This has happened repeatedly and could be related to the current open recall for the CX-3.
- Fuel/propulsion system
The engine on my 2017 CX-3 died while travelling on the interstate at 70mph just before the low fuel light would normally turn on. I pulled to the side of the interstate freaked out at what just happened. I was within a mile of an exit with a gas station and the car started when fuel was added.…
The engine on my 2017 CX-3 died while travelling on the interstate at 70mph just before the low fuel light would normally turn on. I pulled to the side of the interstate freaked out at what just happened. I was within a mile of an exit with a gas station and the car started when fuel was added. It's the exact same low pressure fuel pump failure symptom that later CX-3's are being recalled for. I took it to a Mazda dealer and he only recommended that I keep the tank over half full. I've been hoping the recall would be expanded to include my VIN number but there doesn't appear to be enough complaints yet to do this. I've been filling up at 1/4 tank and haven't had an issue again after driving another 40,000+ miles. This model has disappointing range even without this issue.
- Exterior lighting
Both headlamp lights have water on it (Condensation ocurring on both headlamps) Please verify if this situation could be considered a safety hazard.
- Engine · Fuel/propulsion system
On November 4, 2022 I was driving in the middle lane of I 87 north of Saratoga Springs. The car stalled and died. I was able to get to the break down lane. After sitting for 5 - 10 minutes, completely frazzled, I tried the ignition and the car started. The gas gauge said I had approximately ¼…
On November 4, 2022 I was driving in the middle lane of I 87 north of Saratoga Springs. The car stalled and died. I was able to get to the break down lane. After sitting for 5 - 10 minutes, completely frazzled, I tried the ignition and the car started. The gas gauge said I had approximately ¼ tank left. I filled the car up and made it the rest of the way home. This had happened once before on a local road and we had the car towed. The thought was that maybe the car had run out of gas although the gas gauge did not so indicate. When I took the vehicle to the mazda dealer after considerable research, they indicated there were recalls on Denso fuel pump impellers for the model of my car in 2018 and following but not for my 2017 model. The date of that service was 1/17/23. There were no codes still in place that would identify the problem. I am certain that this is the problem. I only drive the car locally now and i keep the gas tank at least ½ full.
- Fuel/propulsion system
I was driving my 2017 Mazda CX-3 on the interstate when car suddenly jerked and failed to accelerate. I was driving 70 mph in the left lane when this happened and immediately started to pull over to the righthand shoulder of the road. The car jerked and slowed again when we were in the right lane.…
I was driving my 2017 Mazda CX-3 on the interstate when car suddenly jerked and failed to accelerate. I was driving 70 mph in the left lane when this happened and immediately started to pull over to the righthand shoulder of the road. The car jerked and slowed again when we were in the right lane. By the time I pulled off, the check engine light was on and the car had completely stalled. I was stuck on a narrow shoulder with a dog and two people in the car. We were lucky we made it to the shoulder at all before the car stalled. There was no indication before the car jerked that there was any problem with the vehicle. The car was towed to the dealership and the cause of the check engine light was identified as a leaking fuel pump/fuel rail. I had to have the fuel pump replaced along with a valve cover gasket.
- Fuel/propulsion system
Car has 24,547 miles and the fuel pump went out. car stalled while driving and had to be towed by aaa. car was repaired at overbeck auto service 1793 ohio pike, amelia, oh 45102. info@overbeckauto.com
- Air bags · Service brakes · Vehicle speed control
I put my right signals on and came to a near stop, as I did a right turn into the parking space in front of the dry cleaners. I was slowly creeping into the parking space, and pushing the brakes, as I slowed down to a near stop in the parking spot. All of a sudden, as my right foot was still on…
I put my right signals on and came to a near stop, as I did a right turn into the parking space in front of the dry cleaners. I was slowly creeping into the parking space, and pushing the brakes, as I slowed down to a near stop in the parking spot. All of a sudden, as my right foot was still on the brakes, I felt the car lurch forward, and felt myself pulled back into my seat from the velocity, as the car suddenly accelerated forward out of control! I had NO CONTROL OVER THE CAR! I saw myself speeding towards the drycleaners’ glass window storefront! I came to a stop after I had driven over the sidewalk, over some plants, and crashed into the pillar in front of the dry cleaners, completely pulling it off of its foundation. My car’s engine was still running, and the airbags did NOT deploy. This was a case of Sudden Unintended Acceleration where the airbags did not deploy, resulting is serious property damage, but could have been much worse had the pillar not been there to stop my car from breaching the storefront, and potentially hitting a customer or employee.
- Fuel/propulsion system
This IS a fuel pump problem. p/n pell - 1335za. other numbers on the label are 16.12.22 and h00073961. I am in possession of the faulty part. we were travelling at highway speed on route 1 in delaware. the car stalled in the middle lane and we almost made it to the shoulder. my husband, 70…
This IS a fuel pump problem. p/n pell - 1335za. other numbers on the label are 16.12.22 and h00073961. I am in possession of the faulty part. we were travelling at highway speed on route 1 in delaware. the car stalled in the middle lane and we almost made it to the shoulder. my husband, 70, had to push it the shoulder. it would not restart. we had my 95 year old mother in law in the car. the temperature was close to 100 degrees that day and sunny. we were very concerned for her. we called 911 and a state trouper came in about 20 mins. he took my husband to get a a few gallons of gas and the car started. before the stall, we had enough gas for 39 miles. we did not run out of gas. This happened once before about six months earlier on a less busy road and I was able to restart it so I did not fret about it that time and thought it was just a quirky thing. we made it home without further incident. we brought it to the mechanic locally for replacement of the fuel pump. he verified the problem with his diagnostic equipment. the check engine code for the event was p0192. total cost of repair was $900.00. there IS a current fuel pump recall on mazdas but it starts with the model year 2018. mine IS a 2017 but the problem appears to be the same! the component IS in my possession but no other parties, besides the mechanic, have examined it.
- Fuel/propulsion system
On 3 separate occasions this car presented as if it were out of fuel while the gas gauge showed it having fuel. It sputtered then lost power as if it ran out of gas. Two of these times were on the interstate while the 3rd time was in a residential area.
- Fuel system, gasoline
The contact owns a 2017 Mazda CX-3. The contact stated while driving 10 MPH and approaching a stop sign, the vehicle lost motive power and stalled. The contact stated he was unaware if there was any warning light illuminated. The contact added fuel to the vehicle and was able to restart the…
The contact owns a 2017 Mazda CX-3. The contact stated while driving 10 MPH and approaching a stop sign, the vehicle lost motive power and stalled. The contact stated he was unaware if there was any warning light illuminated. The contact added fuel to the vehicle and was able to restart the vehicle. The contact took the vehicle to an independent mechanic and was informed that the fuel pressure sensor needed to be replaced. The vehicle was not repaired. The dealer was not contacted. The manufacturer had not been informed of the failure. The failure mileage was approximately 25,792.
- Fuel system, other › Delivery › Fuel pump
The contact owns a 2017 Mazda CX-3. The contact stated that while driving at an undisclosed speed, the vehicle lost motive power. The contact related the failure to a faulty fuel pump; however, the vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was 139,099.
- Electrical system
I have had this happen multiple times. I try to turn off the car and it will not shut off. It makes noises and beeps, but you can do nothing to turn off the car. This makes the battery die. The first time I freaked out and called Mazda headquarters. They got a tow truck sent to me and my car was…
I have had this happen multiple times. I try to turn off the car and it will not shut off. It makes noises and beeps, but you can do nothing to turn off the car. This makes the battery die. The first time I freaked out and called Mazda headquarters. They got a tow truck sent to me and my car was taken to Brown's Mazda in Fairfax. They told me the battery was dead and that is why that happened. I have had my battery checked by them numerous times and they say it is A-OK and 100% okay, so how can this be. It happened again and I drove straight to the dealer who told me it wasn't the battery but the starting system. They fixed it and I left and 20 minutes later it happened again. It has now happened again. One day my car is fine and the next it does not start. Then, after trying to start it again today. It went crazy and would not shut off. I was at the dealership recently and another woman had this problem. They told her it was the shifting gear and she had to pay a fair amount. This is ridiculous. This is a Mazda problem not an owner problem. No one seems to know what the real issue is or are afraid to tell. This needs to be looked into. The problem is Mazda owners never know when and where this will happen and it could strand us in bad locations with no recourse. There are no warning lights or messages and it happens at random times. It first started two years ago and has been happening repeatedly. The problem has been relayed to Browns Mazda on several occasions and they tell me it is the battery, but every time I get the battery checked it is perfect. Something is wrong and it is probably due to the electrical starting system which also affects the charging terminals. This is a serious issue and someone needs to take a look into this matter. Please help!
- Engine · Fuel/propulsion system
While driving 70 mph on the interstate, vehicle stalled and started jerking, unable to accelerate, losing speed quickly. Fortunately I was able to move onto the shoulder, avoiding a semi truck approaching quickly behind, and another semi trucked parked along the interstate blocking access to the shoulder.
- Engine · Structure › Body
I was in an accident at a very high speed. A driver didn't see me in his left side blind spot and was veering into my lane at 85-90mph. I swerved to the left to avoid the car and my car wouldn't straighten/i couldn't get back the control. I smashed the guardrail with the whole left side of my car…
I was in an accident at a very high speed. A driver didn't see me in his left side blind spot and was veering into my lane at 85-90mph. I swerved to the left to avoid the car and my car wouldn't straighten/i couldn't get back the control. I smashed the guardrail with the whole left side of my car and the car was deemed to be totaled by the insurance company. The airbags never deployed despite the high speed and impact of the accident.
- Unknown or other · Visibility › Defroster/defogger/hvac system
Warm air from the climate control vents- car IS under 45,000 miles and needs a new evaporator- most cars will never need a new evaporator, especially one that IS under four years old. *tr
- Electrical system
2017 mazda CX3. Consumer writes in regards to an issue with vehicles blind spot warning system. *Ld the consumer stated the blind spot system does not appear to be operating well. The system only seemed to register when a vehicle was approached from the rear. Left and right side warnings…
2017 mazda CX3. Consumer writes in regards to an issue with vehicles blind spot warning system. *Ld the consumer stated the blind spot system does not appear to be operating well. The system only seemed to register when a vehicle was approached from the rear. Left and right side warnings appeared to be working as designed. When the consumer's vehicle was doing the overtaking no warning was given. This IS the same for the left and right sides. Updated 09/27/2017*js
- Fuel/propulsion system
Where the plastic center console meets the carpeting on the right side of the gas pedal, there IS a gap. no less than three times in only two months while in motion have I gotten my shoe stuck in the plastic of center console when trying to take it off the gas pedal, leaving me unable to take my…
Where the plastic center console meets the carpeting on the right side of the gas pedal, there IS a gap. no less than three times in only two months while in motion have I gotten my shoe stuck in the plastic of center console when trying to take it off the gas pedal, leaving me unable to take my foot off of the gas pedal. fortunately, I have been able to react quickly each time and shift into neutral, slamming on my break with my left foot. very dangerous!
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11011141Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
- 11009654The SKYACTIV-DRIVE FW6A-EL AT uses Automatic Transmission Fluid (ATF) Type: FZ. Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
- 11009644Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11008577Some customers may complain about scratches on the instrument cluster lens.
- 11007029For improvement of electrical diagnosis, the SKYACTIV Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
- 11007022Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 11007019If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 11007018Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
- 11007013Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
- 11007010Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
- 11007009Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11006998Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
- 11006987In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
- 11006917Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
- 11006899Some customers may notice water entry into the front combination lights (as shown below). This is due to poor sealing where rain or other water can enter inside the light. To eliminate this concern, the shape of the front combination light has been changed to improve sealing ability.
- 11005671Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 11003398Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 11003397Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 11003396Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11000772Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 F (10 C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
- 10254191Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 10254188Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 F (10 C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
- 10254187Some customers may complain about infotainment center display. Peeling, spider cracks and white dots.
- 10252508Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 10252507Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.
- 10251387Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 10251368Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
- 10248385Some customers may complain about infotainment center display: Center display touchscreen operates by itself (Ghost Touch). The film of the center display may be peeled off. White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts.
- 10244679If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 10243569Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 10243568Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 10243551Service bulletin 09-031/20 issued on 09/21/20 IS no longer valid. It IS superceded by recall 6023g (2014-2018 mazda3 and 2016-2021 CX-3 - rearview image may not display properly).
- 10241637Some customers may complain about scratches on the instrument cluster lens.
- 10240496Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 10240431Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. NOTE: The icons and the messages are displayed normally.
- 10240427Be advised that TSB "09-031/20 - REAR MOUNT CAMERA IMAGE NOT CLEAR/NO IMAGE ON SCREEN" is no longer valid and has been superseded by "RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY". Use the link below to view the recall: RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY
- 10240366In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on an as-needed basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The BSM radar aiming is performed whenever the BSM control module, the BSM bracket or the rear bumper is replaced.
- 10238697Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. NOTE: The antistatic effect does not deteriorate with this procedure.
- 10238695Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
- 10238671Some customers may complain that the frequency of replenishing the window washer liquid is higher than expected, or they may complain of leakage at or around the washer motor (1). This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section. This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section.
Every Mazda CX-3 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.