2018 Mazda CX-3

Recalls

1 recall names the 2018 Mazda CX-3. Newest first.

• Back over prevention › Sensing system › Camera

  Jul 14, 2023NHTSA 23V487000236,100 vehicles

  Mazda North American Operations (Mazda) is recalling certain 2014-2018 Mazda3 and 2016-2021 CX-3 vehicles. The rearview camera image may not display properly by showing a flickering or distorted image.

  Risk and remedy

  Risk

  A rearview camera that does not display properly can reduce the driver's rear view, increasing the risk of a crash or injury.

  Remedy

  Dealers will inspect and replace the rearview camera, as necessary. In addition, dealers will install a wiring harness fastening seal. All repairs will be performed free of charge. Interim notification letters, notifying owners of the safety risk, were mailed September 13, 2023. Final owner letters for affected models and model years in the states of CT, MA, MD, NJ, NY, PA and VA were mailed August 14, 2024. The remaining owner notification letters will be mailed at a future date, anticipated on or before May 1, 2025. Owners may contact Mazda customer service at 1-800-222-5500, Option 6. Mazda's number for this recall is 6023G.

  Full recall details →

Owner complaints

What owners report most

1. Back over prevention2
2. Electrical system2
3. Engine2
4. Exterior lighting1
5. Forward collision avoidance1
6. Fuel/propulsion system1
7. Lane departure1
8. Service brakes1
9. Suspension1
10. Unknown or other1

Latest complaints

• May 8, 2026WI
  Engine · Fuel/propulsion system

  Fuel injector failed without warning. A lot of fuel leaked into the engine destroying a spark plug in one cylinder and ultimately ruining the catalytic converter when fuel got into it. Independent mechanic and Mazda dealership diagnosed. Car cannot be driven.

• Dec 10, 2024IN
  Back over prevention
  The contact owns a 2018 Mazda CX-3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount…

  The contact owns a 2018 Mazda CX-3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.

• Mar 16, 2024MA
  Exterior lighting

  Heavy condensation is occurring inside the driver side headlamp. A quick google search shows this is a common problem among Mazda owners and Mazda will not cover the repair. I am unable to get a Massachusetts state inspection sticker due to this.

• Jul 26, 2023NY
  Back over prevention

  The contact owns a 2018 Mazda CX3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

• Jan 31, 2023FL
  Engine · Service brakes · Suspension
  The contact owns a 2018 Mazda CX-3. The contact stated that while driving, the vehicle was moving from left to right. The contact stated that the brakes were making an abnormal scraping sound. There was an abnormal sound coming from the engine. The local dealer was not contacted. There were no…

  The contact owns a 2018 Mazda CX-3. The contact stated that while driving, the vehicle was moving from left to right. The contact stated that the brakes were making an abnormal scraping sound. There was an abnormal sound coming from the engine. The local dealer was not contacted. There were no warning lights illuminated. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was unknown.

• Dec 16, 2021IN
  Forward collision avoidance › Warnings
  Was driving my grandchildren home when an alarm that I had never heard before started sounding and BRAKE! showed up on the heads up display. The car came to a stop out in the middle of the street even though there was nothing in front of or around the vehicle. It was a good thing there was not a…

  Was driving my grandchildren home when an alarm that I had never heard before started sounding and BRAKE! showed up on the heads up display. The car came to a stop out in the middle of the street even though there was nothing in front of or around the vehicle. It was a good thing there was not a car behind me or they would have rear-ended my vehicle and we or the people in the car that hit us could have gotten seriously hurt. I took the car to the dealer and they did a diagnostics check and said no codes came up so there was nothing wrong with the car. They actually told me that when and if it happens again to videotape it for proof.

• Feb 24, 2021WA22,440 mi
  Electrical system · Lane departure › Blind spot detection
  TL* the contact owns a 2018 mazda CX-3. The contact stated while driving 52 mph, the blind spot detection warning indicator was not working. The contact stated that the vehicle was taken to olympia mazda (2201 carriage southwest olympia, wa 98502) where the failure was diagnosed as a blind spot…

  TL* the contact owns a 2018 mazda CX-3. The contact stated while driving 52 mph, the blind spot detection warning indicator was not working. The contact stated that the vehicle was taken to olympia mazda (2201 carriage southwest olympia, wa 98502) where the failure was diagnosed as a blind spot monitoring system failure. The contact stated that the vehicle was repaired under manufacturer communications number: tsb:15-004-18-3539. The contact was upset that the tsb was not a recall. The manufacture was not notified of the failure. The approximate failure mileage was 22,440.

• Dec 20, 2019NC45,000 mi
  Wheels
  I was sold a vehicle with "new" tires. I've only had the vehicle about 6 months and found out the tires were made in 2011 and starting to deteriorate so I had to buy actual new tires. I did not have an accident but feel there could have been a tire blowout. luckily I had run over a bolt and was…

  I was sold a vehicle with "new" tires. I've only had the vehicle about 6 months and found out the tires were made in 2011 and starting to deteriorate so I had to buy actual new tires. I did not have an accident but feel there could have been a tire blowout. luckily I had run over a bolt and was trying to get a tire repair when the tire place told me about the bad condition of all four tires. the dealership first did not believe me but when I showed them a picture they said they can sell tires up to 8 years old as new if they were not previously on a vehicle. I don't know if that IS true but if the tires were starting to dry rot it seems like a bad idea and certainly unethical if not illegal.

• Sep 2, 2018OR3,500 mi
  Electrical system · Unknown or other
  While I was parking my car and braking the throttle opened wide and I jumped the curb. I reapplied the brakes hard and the car came to a stop after skidding 4 feet. (Tire marks measured). I had the car towed to the dealer where they could find nothing wrong. in researching this problem it appears…

  While I was parking my car and braking the throttle opened wide and I jumped the curb. I reapplied the brakes hard and the car came to a stop after skidding 4 feet. (Tire marks measured). I had the car towed to the dealer where they could find nothing wrong. in researching this problem it appears the electronic throttle system can at rare times have voltage problems that can cause this. my dealer could not replicate this but it has been done in a study by the korean national forensic service. since all new cars have the same electronic throttle systems I am unable to buy a car that won't be vulnerable to this. I am currently still driving my car with. My hand on the gear handle to put the car in neutral if it happens again. as soon as auto makers admit that sudden unintended acceleration IS caused by electrical problems with their cars I will buy a new car from the company who fixes this problem. in my research of this problem I found many other people with new cars all brands that this has happened too. I believe that human err could at times be a contributor to the problem but in my case I know my foot was on the brake when this happened. I love my new car and would not complain otherwise. please look at dr. Ronald l. Belts research into this problem and his conclusions. thank you

• Aug 31, 2018MN12,600 miCrash
  Vehicle speed control

  I was in a parking ramp, I rounded the corner going up and was pulling into a parking spot, my foot was on the break, and the car accelerated. I lurched forward into a wall of the ramp. It wasn't raining so pavement and ramp were not wet. The dealer has looked at the car, said they saw break and gas pedal active at the same time. They said nothing was wrong with the car.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11011345CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
• 11011341CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
• 11011338CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
• 11011336CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
• 11011331CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
• 11011326CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
• 11011141Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
• 11009654The SKYACTIV-DRIVE FW6A-EL AT uses Automatic Transmission Fluid (ATF) Type: FZ. Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
• 11009644Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 11008577Some customers may complain about scratches on the instrument cluster lens.
• 11007029For improvement of electrical diagnosis, the SKYACTIV Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
• 11007022Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
• 11007019If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
• 11007018Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
• 11007013Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
• 11007010Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
• 11007009Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 11006998Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 11006987In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
• 11006917Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
• 11006899Some customers may notice water entry into the front combination lights (as shown below). This is due to poor sealing where rain or other water can enter inside the light. To eliminate this concern, the shape of the front combination light has been changed to improve sealing ability.
• 11005671Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 11003398Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 11003397Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
• 11003396Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 11003351Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.
• 11000785The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission
• 11000775There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
• 11000772Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 F (10 C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
• 10254191Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
• 10254188Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 F (10 C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
• 10254187Some customers may complain about infotainment center display. Peeling, spider cracks and white dots.
• 10252508Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10252507Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.
• 10251387Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10251368Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 10248392There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
• 10248385Some customers may complain about infotainment center display: Center display touchscreen operates by itself (Ghost Touch). The film of the center display may be peeled off. White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts.
• 10246121The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
• 10244679If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

Every Mazda CX-3 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.