2023 Mazda MX-5

Recalls

1 recall names the 2023 Mazda MX-5. Newest first.

• Air bags › Air bag/restraint control module › Software

  Sep 18, 2024NHTSA 24V69500077,670 vehicles

  Mazda North American Operations (Mazda) is recalling certain 2016-2023 MX-5 Miata vehicles. A software error in the air bag control module may cause the front air bags to deploy with excessive force during a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."

  Risk and remedy

  Risk

  An air bag that deploys with excessive force can increase the risk of injury during a crash.

  Remedy

  Dealers will update the Sophisticated Air Bag Sensor (SAS) control module software, free of charge. Owner notification letters were mailed November 7, 2024. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 6924I.

  Full recall details →

Owner complaints

What owners report most

1. Power train4
2. Air bags1
3. Seat belts1
4. Steering1
5. Unknown or other1

Latest complaints

• Apr 1, 2026MD
  Steering
  Steering feels sticky at higher speeds, once the vehicle is at full operating temp. The steering requires some pressure to “break free” from whatever position it is in. If I’m continually moving the wheel, it steers normally. However, if I’m driving straight and need to initiate a turn or make…

  Steering feels sticky at higher speeds, once the vehicle is at full operating temp. The steering requires some pressure to “break free” from whatever position it is in. If I’m continually moving the wheel, it steers normally. However, if I’m driving straight and need to initiate a turn or make minor steering corrections (like on the highway), I have to turn the wheel harder than normal, then it gives way and turns with regular force. This makes it difficult to control, causing the car the jerk around a lot. This is an issue many others have noticed on online forums, and there does not seem to be a known fix for this. The Mazda dealership near me could not duplicate the issue (since it takes 20-30 minutes of continuous driving for this steering issue to get worse to the point of concern), and therefore refused to look any further. This makes it unsafe to drive longer than 20-30 minutes. I am currently awaiting an appointment with an independent service center. There are no warning lamps, messages, or other symptoms that I'm aware of

• Sep 22, 2025VA
  Power train

  Manual transmission will not reliably shift from 2nd to 3rd gear without a grinding noise. Other owners are reporting similar issues that have required a full replacement of the transmission in MY2023 cars.

• Jun 6, 2025LACrash1 injury
  Air bags
  On [XXX] my [XXX] son was driving the vehicle and at low speed (30 mph or under) lost control of the vehicle in a turn. The vehicle hit a telephone pole that was rotted from termite infestation which shattered into three pieces (one piece landing on the cars windshield frame and driver roll bar…

  On [XXX] my [XXX] son was driving the vehicle and at low speed (30 mph or under) lost control of the vehicle in a turn. The vehicle hit a telephone pole that was rotted from termite infestation which shattered into three pieces (one piece landing on the cars windshield frame and driver roll bar hoop) . He impacted the airbags and had an unstable anterior fracture of the c5 vertebrae and a stable posterior fracture of the C5 vertebrae. He was graded an Asia B spinal cord injury and was paralyzed from the neck down. He spent 42 days in trauma ICU and then Neuro Rehab learning how to walk and use the bathroom. He has many lingering effects and still has loss of use of fingers on both hands as well as difficulties walking and gripping objects. His passenger did not hit the airbags and was uninjured. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• Jan 31, 2025NY
  Power train
  My vehicle has only 8700 miles. At around 2500 miles first gear refused to engage, and I had to start the car in second for a week. That week I scheduled for service but the problem was not reproducible, since then it has been intermittent by never prolonged like that full week. This is and was a…

  My vehicle has only 8700 miles. At around 2500 miles first gear refused to engage, and I had to start the car in second for a week. That week I scheduled for service but the problem was not reproducible, since then it has been intermittent by never prolonged like that full week. This is and was a safety risk because I have been stuck on a hill, stop signs, and green traffic lights etc. Because it was not reproducible, the claim was dismissed. At around 4000 miles and on, third gear became very inconsistent in shift action. Typically it won't allow me to shift into third at all, other times it will grind, or requires excessive force to engage gear. This happens both in motion and at a stop. In traffic, the sudden loss in speed and rpm from being unable to shift into third poses a risk, especially getting onto on ramps. The dealer still cannot reproduce the issue, and in fact I have a 2 minute long video of the fault - pending their response to the video. Mazda corporate claims this is not a known or common issue. No warning lights pick up this fault. I have since continued to come to a resolution, and will return to the dealership.

• Oct 29, 2024CA
  Seat belts · Unknown or other
  Dear, I’m writing to address the delayed response to the recall for my Mazda MX-5, which began on September 18. It has been nearly two months without any remedy or guidance from the manufacturer. As I rely on this vehicle daily for business purposes, this prolonged delay has caused significant…

  Dear, I’m writing to address the delayed response to the recall for my Mazda MX-5, which began on September 18. It has been nearly two months without any remedy or guidance from the manufacturer. As I rely on this vehicle daily for business purposes, this prolonged delay has caused significant disruptions. I urge NHTSA to assist in expediting a resolution with Mazda to minimize further impact on my work. Thank you for your attention to this matter.

• Sep 9, 2024OH
  Power train
  The manual transmission has a synchronizer failure. Safety was put at risk due to inability to safely complete a gear change reliably. The problem has been reported to the dealer and the transmission has been replaced once and is scheduled to go in 9/23/24 for a possible second transmission…

  The manual transmission has a synchronizer failure. Safety was put at risk due to inability to safely complete a gear change reliably. The problem has been reported to the dealer and the transmission has been replaced once and is scheduled to go in 9/23/24 for a possible second transmission replacement. There are no warning lights associated with the failure. The only symptom is the inability to complete a shift with no warnings of this failure prior to it first presenting itself.

• Jul 6, 2024MO
  Power train
  Mazda Miata model years 2022-2024 with manual 6sp transmission are experiencing a large number of failures at low mileage. Some owners are reporting 2 failed transmissions at less than 10,000 miles. 3rd and 4th great become unusable without warning, increasing the potential for a crash. There…

  Mazda Miata model years 2022-2024 with manual 6sp transmission are experiencing a large number of failures at low mileage. Some owners are reporting 2 failed transmissions at less than 10,000 miles. 3rd and 4th great become unusable without warning, increasing the potential for a crash. There have been over 50 reports of manual transmission failure from 2022-2024 Miata owners. Concern: When the transmission internals fail without warring the vehicle experiences loss of power and forward movement, substantially increasing the chance of an accident in a highway driving scenario. This problem has been confirmed by Mazda dealer network. Mazda is offering to replacement transmissions, but has not told the owners if there have been modifications and improvements to the replacement units to resolve the issue, or if they are replacing the defective transmission with same kind.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11011141Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
• 11009655This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.
• 11009644Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 11008577Some customers may complain about scratches on the instrument cluster lens.
• 11007029For improvement of electrical diagnosis, the SKYACTIV Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
• 11007027Before judging a steering wheel as having premature wear or a defect, first clean the steering wheel as explained in the repair information. Some vehicles may have steering wheel stains caused by chemicals such as hand lotions.
• 11007022Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
• 11007019If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
• 11007018Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
• 11007013Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
• 11007010Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
• 11007009Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 11006998Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 11006987In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
• 11005671Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 11005551At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. Wrinkles may not be completely removed after the repair is completed. Leather is a natural material and may develop some wrinkles due to aging and wear during normal useage.
• 11005546Some vehicles may exhibit scratches (1) on the rear of the seat back bar garnish (2) from contact with the convertible top (3). Due to assembly variations, the clearance between the seat back bar garnish and the convertible top is too small on some vehicles.
• 11003398Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 11003397Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
• 11003396Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 11003223Some vehicles may exhibit the inner cloth (A) falling down at the rear end causing a poor appearance and obstructing the view of the back window. This is caused by: CASE A: The J-hook binding holding the inner cloth coming loose because the convertible top is opened/closed a lot or from high ambient temperatures. CASE B: After the previous improvement carried out at the supplier since January 19, 2016, some J-hooks have still been found coming loose to bind and hold the inner cloth during the assembly process. To correct the problem: CASE A: Two top-protector clips have been additionally installed to both side edges of the J-hook to prevent the J-hook from loosening and separating. CASE B: An improved inspection process has been started at the supplier to check the appearance of the inner cloth after installation of the clip.
• 11000785The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission
• 11000782This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.
• 11000775There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
• 11000772Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 F (10 C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
• 10254191Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
• 10252508Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10252507Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.
• 10252375Some vehicles may exhibit crack(s) on the left and/or right side retractable hardtop quarter garnish (1). The molding material on the retractable hardtop quarter garnish may accelerate the deterioration of the quarter garnish, resulting in the cracks. To eliminate this concern, the molding material on the retractable hardtop quarter garnish has been improved.
• 10252372Some vehicles may exhibit scratches (1) on the rear of the seat back bar garnish (2) from contact with the convertible top (3).
• 10251387Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10251370Some customers may complain that the tire sidewalls are distorted or "damaged". Sidewall waviness/indentations/undulations are common on radial tires and are more noticeable on tires with taller sidewalls. The higher the tire pressure, the more noticeable the effect will be. Be sure to set the tire pressures at the recommended tire pressure on the vehicle tire label. Sidewall indentations are a cosmetic condition that does not affect the performance of the tires.
• 10251369Some vehicles may exhibit a steering shimmy or body vibration during the PDI test drive or during the first few miles of driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).
• 10251368Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 10248392There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
• 10248390Before judging a steering wheel as having premature wear or a defect, first clean the steering wheel as explained in the repair information. Some vehicles may have steering wheel stains caused by chemicals such as hand lotions.
• 10246133At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface.
• 10246121The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
• 10244679If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
• 10243569Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.

Every Mazda MX-5 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.