2001 Mercedes Benz C230

Owner complaints

What owners report most

1. Electrical system1
2. Engine and engine cooling1
3. Service brakes1
4. Unknown or other1

Latest complaints

• Sep 29, 2015FL126,000 mi
  Service brakes

  TL* the contact owns a 2001 mercedes benz C230. The contact stated that while driving 60 mph, the front driver side brake seized without warning. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was 126,000.

• Jun 10, 2002FL
  Engine and engine cooling › Engine › Gasoline

  While at a complete stop vehicle will shut off trying to accelerate. Contacted dealer, and the dealer was not willing to do anything.*ak

• Feb 6, 2002CAFire
  Electrical system › Wiring › Front underhood

  Consume r was traveling on the highway. And without prior warning there was smoke coming from underneath of hood. vehicle was on fire. dealership was aware of problem.*ak

• Mar 27, 2001FL
  Unknown or other

  The information screen which houses basic driver information (odometer, gear range indicator, time, temperature) can not be seen in when driving on a sunny day, this washout of the information could causes the driver to concentrate on the screen and loose full control of the vehicle. nlm

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10205233Mobile phone cotacts are not transferred completely.
• 10186141NTG5.5: Incorrect time shown on instrument cluster, COMAND display, and analog clock
• 10186135If the customer brakes sharply from a speed of > 30mph, without ABS intervention, there is a single cracking noise from the area of the ESP hydraulic unit
• 10181124Harsh engagement when changing gear range from P to D or R
• 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
• 10166994Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). Heard once when changing from forward to reverse (and vice versa)
• 10166975This Customer 1 Action has been initiated because certain mbrace subscribers were recently contacted by mbrace informing them that they need to have an i-button call performed to ensure their mbrace device has registered with the Verizon Telematics systems. If the i-button call failed or if the customer was unable to perform the i-button call, the mbrace agent instructed the customer to make an appointment with their dealer to have the issue corrected and/or i-button call performed. The vehicles impacted range from model year 2002 to 2014.
• 10166099Pneumatic comfort systems with insufficient performance, entirely inoperative or leaky.
• 10166095Noise from the front seats during load change.
• 10166087The presence of a quiescent current can have several causes. These are not always recognized and lead to an increased number of OK components being removed. Possible Hall sensor faults or normalization faults can exist which can be eliminated without replacing the control unit.
• 10166085Grunting noise or ripping noise at seat-back lining
• 10166082Noises from area of seat adjuster or cushion frame.
• 10166081Noise complaints when load on backrest frame changes. Affects the driver and front passenger seats. Also perform the remedial action if you are performing work on: - backrest frame - backrest cover or - guide rail of head restraint. If the backrest frame is exposed as a result, the actions must always be performed in order to avoid follow-up repairs.
• 10164810Throttle lift-off clunking noises at drive shafts of front axle
• 10151959Seat belt extender toothed rack sluggish or makes noises
• 10135599Clunking noise from front axle suspension strut or rear axle shock absorber on short strokes of the damper
• 10034988Mercedes benz (daimler): unsatisfactory brake servo assistance after a cold start, primarily when maneuvering. Low vacuum in the intake manifold due to wide open throttle valve. Retrofit electric brake booster vacuum pump (M56). Model 203. No model year listed.
• 10034306Mercedes: airbag durability and reliability. Air bag srs control module (N2/2) does not have a set shelf life and will normally be reliable for the life of a vehicle. With 164, 216 221, 251 and newer, the airbag control unit can be reset five times. With modes 202, 210 and newer, the airbag control unit can be reset three times. Earlier models would have to have their airbag control unit and triggered restrain components changed only after an accident. No models or model years listed.
• 10028624Mercedes vehicle: the anti-lock brake system (ABS) return flow pump running without control with corresponding fault code c1401, clean and insulated the connector for the return flow pump relay. Models 202 and 208. Model years unknown.
• 10028586Mercedes vehicle: the srs indicator lamp IS illuminated and code b1058 and b2dbo are stored, replace the srs control unit. Models 203 and model 209. Model years unknown.
• 10028585Mercedes vehicles: the xenon or bi-xenon headlamp not functioning. A function description can be found in wis document gf8s.10-p-20010 (203), gf82.10-p-0003q (209); gf82.10-p-3002r (230). Model years uknown.
• 10025642Model 203 (c) series from production 8/1/01 to 2/1/03 and model 209 (CLK) series up to production 2/1/03; esp visit workshop with fault code c1185.
• 10022893Check engine light on / fault codes fc1200 / fc1208 stored in me-sfi control unit. Mercedes-benz model C230, C280, C350, slk280, slk350, clk350, clk550, E350, E550, cls550, S600, and sl550. Equipped with M272 engine or M273 engine. Updated 8/28/08.
• 10020460Play in the rack and pinion steering system. Models 203, 209, 210, 211, 215, 220, 230. Mercedes benz. Updated 5/13/09.
• 621577Subject regarding smartkey intermittently inoperative.

Every Mercedes Benz C230 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.