2017 Mercedes-Benz GLC300
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › GLC300 › 2017
These records cover every 2017 Mercedes-Benz GLC300. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
12 recalls name the 2017 Mercedes-Benz GLC300. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel…
Risk and remedy
Risk
A detached roof panel can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the front panel, free of charge. Owner notification letters were mailed on August 2, 2024. Owner notification letters will be mailed in phases, on, March 22,2024, and August 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 21V-197.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017…
Risk and remedy
Risk
The adhesive bonding of the front panel might deteriorate, possibly causing the front panel to detach from the vehicle and become a road hazard, increasing the risk of a crash.
Remedy
Mercedes-Benz dealer will remove the bonded panel and will install a new front panel by following the detailed repair instructions and using the approved primer, cleaner and adhesive, free of charge. Owner notification letters were mailed on September 3, 2021 and October 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2019 C300, E300, 2018-2020 CLA250, 2020 CLS450, AMG E53, AMG GT53, GLE450, 2018 AMG E63, AMG GTA, 2017-2020 GLA250, GLC300, 2019 GLC350, AMG GLC43, 2017-2018 GLE350, 2019 AMG GLC 43, GLC350, GLE400, 2017 GLS450, S550, C300 Cabrio, and 2018-2019 S560 vehicles. On June 18, 2021, an additional 9…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting emergency services through the call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the communication module and activate it, if necessary, free of charge. The recall began March 31, 2021. Letters for the owners of the 9 additional vehicles were mailed July 9, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021030005.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2016-2018 Mercedes-Benz GLC300 and GLC300 4Matic, 2018 GLC350e and GLC63 AMG 4Matic and 2017-2018 GLC43 AMG 4Matic vehicles. The seat belt latch plates (the parts that insert into the buckles) for the outboard rear seats may retract into the interior paneling, preventing the occupants from being able to…
Risk and remedy
Risk
If the rear seat passengers cannot fasten their seat belts, they have an increased risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will install felt strips between the C-pillar and rear side paneling, free of charge. The recall began November 2, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018100002.
Mercedes Benz USA LLC (MBUSA) is recalling certain 2017-2018 GLC43 AMG, 2016-2018 GLC300 4Matic, 2016-2018 GLC300, 2018 GLC63 AMG 4Matic, and 2018 GLC350e 4Matic vehicles. The seat belt latch plates (the parts that insert into the buckles) for the outboard rear seats may retract into the interior paneling, preventing the occupants from being able to use…
Risk and remedy
Risk
If the rear seat passengers cannot fasten their seat belts, they have an increased risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will install a buffer to the c-pillar paneling, free of charge. The recall is expected to begin May 14, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018030012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016-2017 GLC300, GLC300 4MATIC and GLC43 4MATIC vehicles. These vehicles may have misadjusted headlights, possibly resulting in the low beam headlights insufficiently illuminating the roadway. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS)…
Risk and remedy
Risk
An insufficiently illuminated roadway may increase the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect the headlamp adjustment, adjusting it as necessary, free of charge. The recall began on January 12, 2018. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2018 GLC300, GLC300 4Matic, and GLC43 AMG vehicles. The fixed panoramic sun roof frontal and side plastic panels may have insufficient bonding, allowing the panels to separate during vehicle operation.
Risk and remedy
Risk
If the sun roof panels detach from the vehicle, it can increase the risk of a crash or injury for following traffic.
Remedy
MBUSA will notify owners, and dealers will inspect the bonding on the sun roof panels, correcting it as necessary, free of charge. The recall is expected to begin December 2017. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2017110009.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC. (MBUSA) is recalling one 2017 C43 AMG, one E300 4Matic sedan, one GLC300, and one E43 AMG 4Matic sedan. These vehicles have electrical power steering control units with improperly welded contact pins.
Risk and remedy
Risk
The improperly welded pins may lose contact, deactivating the power steering assist and increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the electric power steering rack, free of charge. The recall is expected to begin November 10, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017 C300, C300 4Matic, C300 Coupe, C300 Coupe 4Matic, C43 AMG, C43 AMG Coupe, C43 AMG Cabrio, C63 AMG, C63 AMG Coupe, C63S AMG, C63S AMG Coupe, C63S Cabrio, GLC300, GLC300 4Matic, GLC43 AMG, S550, S550 4Matic, S550e, S600, S63 AMG 4Matic, S65, Mercedes-Maybach S550 4Matic, and Mercedes-Maybach S600…
Risk and remedy
Risk
If the front seat seatbelt pretensioners do not function properly, the seat occupants may not be adequately restrained in the event of a crash, increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will replace the front seat belts, free of charge. The recall began October 13, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2015-2017 C300 4Matic, C300, CLA250, CLA250 4Matic and CLA45 AMG vehicles, 2017 C300 4Matic Cabrio, C300 4Matic Coupe, C300 Cabrio, C300 Coupe, E300, E300 4Matic, E400 4Matic Wagon, E43 AMG 4Matic, GLA250, GLA250 4Matic and GLC300 4Matic Coupe vehicles and 2016 C350e and GLC300 vehicles and 2016-2017 C450…
Risk and remedy
Risk
If the starting current limiter overheats, the surrounding components can melt, increasing the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will install an additional fuse in the electrical line to the starter, free of charge. The recall began August 31, 2017. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2017080002.
Owner complaints
101 complaints3 involved a crash2 involved a fire2 injuries
What owners report most
Latest complaints
- Unknown or other
My 2017 Mercedes-Benz GLC 300 is equipped with a panoramic sunroof. The sunroof mechanism and rails were repaired and replaced previously. Approximately a month and a half ago, following heavy rainfall, I discovered water staining on the interior headliner, indicating possible water intrusion…
My 2017 Mercedes-Benz GLC 300 is equipped with a panoramic sunroof. The sunroof mechanism and rails were repaired and replaced previously. Approximately a month and a half ago, following heavy rainfall, I discovered water staining on the interior headliner, indicating possible water intrusion through the panoramic roof assembly. I returned the vehicle to the Mercedes-Benz dealership for inspection. The dealership advised me that the seals around the panoramic roof had deteriorated or failed and quoted approximately $10,000 to replace the affected assembly. I am concerned that water entering the vehicle through the roof could potentially reach electrical components, cause electrical malfunctions, damage safety-related systems, or create other hazards. I am also concerned that the panoramic roof may not be adequately sealed despite the previous repair. Mercedes-Benz USA has advised me that there are no active recalls associated with my vehicle identification number. However, I am reporting this issue to NHTSA because I believe the failure of the panoramic roof sealing system warrants review for a potential safety-related defect, particularly given the previous repair and subsequent water intrusion. The problem was evaluated by an authorized Mercedes-Benz dealership. The dealership's diagnosis and repair records may be available for inspection upon request. I have purchased a vehicle cover to help protect the car from further rain exposure while this issue remains unresolved. I request that NHTSA review this complaint to determine whether this condition may affect other vehicles of the same make and model. I am concerned that the previous repair did not resolve the underlying problem. I am requesting that NHTSA examine whether recurring panoramic roof problems and seal failures may represent a broader safety concern for owners of these vehicles.
- Fuel/propulsion system
Independent service company said the car has a raw fuel smell under the vehicle. Signs of fuel leak at the connection between the high pressure fuel rail / high pressure fuel pump line. Mentioned a recall campaign of 2022030003. That addresses this issue. I contacted Mercedes Benz dealers (2) and…
Independent service company said the car has a raw fuel smell under the vehicle. Signs of fuel leak at the connection between the high pressure fuel rail / high pressure fuel pump line. Mentioned a recall campaign of 2022030003. That addresses this issue. I contacted Mercedes Benz dealers (2) and they said my VIN does not show a recall. The recall does show up online via an AI search and it is supposed to cover 2016-2020 GLCs like ours. Don't know why this is. Can you help?
- Air bags
The contact's wife owns a 2017 Mercedes-Benz GLC300. The contact stated that while the vehicle was parked in the driveway, the air bags inadvertently deployed without impact to the vehicle. The vehicle was towed to the dealer and remained with the dealer for over a month. The contact was called by…
The contact's wife owns a 2017 Mercedes-Benz GLC300. The contact stated that while the vehicle was parked in the driveway, the air bags inadvertently deployed without impact to the vehicle. The vehicle was towed to the dealer and remained with the dealer for over a month. The contact was called by the dealer and informed to retrieve the vehicle even though the cause of the failure was not yet determined. The contact notified the manufacturer and was informed that the issue was under investigation. The vehicle remained unrepaired with the dealer. The failure mileage was approximately 189,800.
- Fuel/propulsion system
I smell gas in my car. There is a recall for the fuel parts on the 2019. I have a 2017 with the same issue.
- Air bags · Forward collision avoidance
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated while driving at an undisclosed speed, the messages "Driver’s Air Bag Malfunction - Service Required" and "Collision Prevention Assist Unavailable" were displayed. The vehicle was taken to an independent mechanic who diagnosed and…
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated while driving at an undisclosed speed, the messages "Driver’s Air Bag Malfunction - Service Required" and "Collision Prevention Assist Unavailable" were displayed. The vehicle was taken to an independent mechanic who diagnosed and determined that the air bag had malfunctioned. The vehicle was not repaired. The contact called the dealer, but the vehicle was not inspected or repaired. The manufacturer was made aware of the failure and referred the contact to the NHSTA Hotline for assistance. The failure mileage was approximately 130,000.
- Seat belts › Rear/other › Buckle assembly
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated that while parked and attempting to release the seat belt, the seat belt remained latched. The contact stated that after the third attempt, the seat belt operated as needed. The failure had occurred in the front driver’s and…
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated that while parked and attempting to release the seat belt, the seat belt remained latched. The contact stated that after the third attempt, the seat belt operated as needed. The failure had occurred in the front driver’s and passenger’s side seat belts. The vehicle was taken to a dealer, where it was determined that the buckle and needed to be replaced. The seat belt buckle was replaced, and the vehicle was repaired. The manufacturer was notified of the failure but offered no assistance because the warranty had expired. The approximate failure mileage was 71,000.
- Visibility › Sun/moon roof assembly
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated that while driving approximately 30 MPH, the first panel of the panoramic sunroof went off track and failed to close as intended. The contact stated that while inspecting the vehicle, the panoramic sunroof glass was pushed down…
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated that while driving approximately 30 MPH, the first panel of the panoramic sunroof went off track and failed to close as intended. The contact stated that while inspecting the vehicle, the panoramic sunroof glass was pushed down firmly, and the sunroof closed. The contact attempted to open the sunroof, but the sunroof failed to operate as intended; however, the contact heard a motorized sound coming from the sunroof. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 70,000.
- Power train
The Valve body control failed. I took the car into the dealership but upon doing some searching this seems to be a common issue amongst owners of this vehicle/make model. The transmission won't go beyond 5th gear (of 9) so it's is dangerous to drive on the interstate. The car doesn't shift into…
The Valve body control failed. I took the car into the dealership but upon doing some searching this seems to be a common issue amongst owners of this vehicle/make model. The transmission won't go beyond 5th gear (of 9) so it's is dangerous to drive on the interstate. The car doesn't shift into drive, only shifts into N, the reverts automatically to park. It required the engine shutting on/off multiple times and only then does it go into 3rd gear, causing the vehicle to jump due to missing gears. This issue could leave an owner stranded at any time and cause injury due to the limitations of the gears. It was inspected and confirmed behavior by Mercedes in Durham NC. There were no warning lamps, there were no signs of the issue. The technician did plug it in and was able to read the fault codes but it didn't trigger a light. The appeared first about 45 days ago, and the vehicle was taken in to be looked at 7/21/25.
- Electrical system · Unknown or other
My vehicle goes into neutral while driving which poses a major risk.
- Visibility › Sun/moon roof assembly
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated that on several occasions while opening the sunroof, the contact heard an abnormal grinding sound. Additionally, the contact stated that the sunroof failed to close as intended. The vehicle was taken to a dealer where it was diagnosed…
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated that on several occasions while opening the sunroof, the contact heard an abnormal grinding sound. Additionally, the contact stated that the sunroof failed to close as intended. The vehicle was taken to a dealer where it was diagnosed and determined that the sunroof rails needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 82,000.
- Air bags · Power train · Seat belts
Vehicle has previous recalls done and still has the same issues with recall. Srs code no air bag will deploy. Dealer ship refused to service vehicle due to miscommunication and I'm driving a defective vehicle without an airbag which could lead to a bad accident waiting to happened. I will like to…
Vehicle has previous recalls done and still has the same issues with recall. Srs code no air bag will deploy. Dealer ship refused to service vehicle due to miscommunication and I'm driving a defective vehicle without an airbag which could lead to a bad accident waiting to happened. I will like to file a complaint against Mercedes of Richmond for refusing to service my vehicle without a defective air bag and the passenger seat bear latch doesn't retract properly. So I'm currently dealing with 2 huge safety hazard and was denied service due to a miscommunication with Steven Powers (service technician) at Mercedes of Richmond! I will like an investigation done.
- Air bags · Power train · Seat belts
No incident my vehicle has a front left malfunction service required light and issues with the passenger seatbelt not proper latching. Upon checking I notice my car had previous recalls done. It seems as if the same issues has come about. NHTSA: 18v177- seat belt not retracting properly. NHTSA…
No incident my vehicle has a front left malfunction service required light and issues with the passenger seatbelt not proper latching. Upon checking I notice my car had previous recalls done. It seems as if the same issues has come about. NHTSA: 18v177- seat belt not retracting properly. NHTSA: 17V627 is related to the steering column switch replacement of clock spring. So if me or a family member was to get into an accident no airbag will deploy! Huge safety hazard!
- Visibility › Rearview mirrors/devices › Exterior
The driver mirror and passenger mirror are warping or having some type of melting effect happening to it.
- Air bags › Frontal › Driver clockspring/spiral cassette · Seat belts
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated that while driving on several occasions at various speeds, the front passenger’s side seat belt retractor failed to extend or retract as intended and became stuck. The vehicle was not diagnosed or repaired. The manufacturer was not…
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated that while driving on several occasions at various speeds, the front passenger’s side seat belt retractor failed to extend or retract as intended and became stuck. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. Additionally, the contact stated that on several occasions while started and running, the message “Service Soon” was displayed. The vehicle was taken to a dealer where it was diagnosed and determined that the clock spring needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 120,000.
- Engine
-The malfunctioned component is the Positive Crankcase Ventilation. - Vehicle wanted to stall and did not want to accelerate while in the middle lane on the highway with my family. - Yes it has been diagnosis by certified mechanic - The check engine light turned on at the time of the incident and has been turning on and off ever since.
- Engine
I was driving and my engine light came on. I ran the code and it came up as P052E which has to do with the positive crankcase ventilation regulator valve. I’ve heard that this part goes out very often on the Mercedes Benz.
- Engine
Car stalled in traffic due to code P052E PCV regulator valve
- Fuel system, gasoline › Storage › Tank assembly
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated that while operating the vehicle, the fuel gauge provided incorrect information and indicated that there was no fuel in the fuel tank. The contact stated that the failure was intermittent and sometimes occurred immediately after…
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated that while operating the vehicle, the fuel gauge provided incorrect information and indicated that there was no fuel in the fuel tank. The contact stated that the failure was intermittent and sometimes occurred immediately after refueling. The vehicle was taken to the local dealer who diagnosed the vehicle and determined that the fuel tank needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 55,000. The VIN was not available.
- Fuel/propulsion system
Strong gasoline smell coming from the engine bay every morning at start up. I removed protective plastic lining from the under carriage to identify the issue. I identified a lot of gasoline dripping from the top portion of the engine compartment where the High Pressure Fuel Pump is located. There…
Strong gasoline smell coming from the engine bay every morning at start up. I removed protective plastic lining from the under carriage to identify the issue. I identified a lot of gasoline dripping from the top portion of the engine compartment where the High Pressure Fuel Pump is located. There was no warning or check engine lights that alerted of this issue of a gasoline leak. This is very dangerous as it could cause the vehicle to catch fire.
- Engine · Tires › Pressure monitoring and regulating systems · Visibility › Sun/moon roof assembly
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken back to the dealer and the contact was informed that the vehicle was repaired. The contact stated that the dealer had only reset…
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken back to the dealer and the contact was informed that the vehicle was repaired. The contact stated that the dealer had only reset the codes. In addition, the contact stated that the tire pressure sensor warning light was illuminated. The contact stated that the sunroof latch failed to close as needed using the sunroof power switch. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 88,100.
- Engine · Power train
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated while driving at an undisclosed speed, the accelerator pedal was depressed, however, the vehicle failed to accelerate as intended. In addition, the check engine warning light illuminated. The vehicle was taken to the dealer where…
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated while driving at an undisclosed speed, the accelerator pedal was depressed, however, the vehicle failed to accelerate as intended. In addition, the check engine warning light illuminated. The vehicle was taken to the dealer where it was diagnosed with a failed positive crank valve. The contact was informed that the positive crank valve needed to be replaced. In addition, the contact was informed that the repair was covered under an extended warranty program, however, the parts were on backorder. The vehicle was not repaired. The contact stated that the failure began in December 2023, however the warranty repair was completed in September 2024, due to parts being on back order. The vehicle was repaired, however, the failure reoccurred. The contact stated while driving at an undisclosed speed, the accelerator pedal was depressed, however, the vehicle failed to accelerate as intended. In addition, the contact heard a loud boom that came from the engine. The vehicle was taken to the dealer where it was diagnosed with a blocked turbo. The contact was informed that the turbo needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and a case was filed. The failure mileage was approximately 94,000.
- Tires
I previously submitted a problem My #11606217 I found out that these tires (2nd set replacement due to tread low within 7 months) I am very concerned that due to the DOT # on these tire is 0119 (last four) which is 5 years old I do not feel safe to travel on tires that is 5 yeas old The…
I previously submitted a problem My #11606217 I found out that these tires (2nd set replacement due to tread low within 7 months) I am very concerned that due to the DOT # on these tire is 0119 (last four) which is 5 years old I do not feel safe to travel on tires that is 5 yeas old The original purchase was January 2024. They were replaced (due to tread worn) with these tires August 2024 What is the timeframe for tires purchased I purchased 2 tires previously (front) from the Mercedes dealer 2 years ago and the DOT# is 4622 Please let me know if these tires are safe for long distance
- Tires
On [XXX], I purchased 2 Brand New Tires for my vehicle from (Howie's Tires (No. Miami Fl) This company is a DBA Walter James Investments LLC These tires was to be placed on the rear and moved the rear tire (Mercedes) to the front On [XXX], the passenger front tire (Mercedes) blow out due to a…
On [XXX], I purchased 2 Brand New Tires for my vehicle from (Howie's Tires (No. Miami Fl) This company is a DBA Walter James Investments LLC These tires was to be placed on the rear and moved the rear tire (Mercedes) to the front On [XXX], the passenger front tire (Mercedes) blow out due to a nail I was towed along with my vehicle to Howie's to purchased another tire to replace the passenger front. I have always purchased my tires from Mercedes-Benz (Ft Lauderdale, FL) I was told by a mechanic (July 31, 2024) that I would soon need rear tires due to the tread was very low These tires were not 7 months old. I DONT UNDERSTAND I contacted Renzo at Howie's I went in on August 1, 2024 to let them see this. He said also said the tread was low. Another guy (maybe the manager) came out. He started telling me the those were not their tire also I had them rotated. He wanted me to pay for a another tire and he give me one. I said no to his accusations. Today, August 2, 2024, I had these tire installed. I asked them was their a DOT number that should be on my receipt he said no to both times. I was told there is and I will like you to look into this for me. Well after a lot of going back and forth he agreed to replace them I submit this form to find out if the tires that was replaced (for purchased January 24)and the passenger front tire (purchased? is indeed brand new Run Flat tires Please let me know the DOT number Thanks so much INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Electrical system
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated while driving at an undisclosed speed, the vehicle inadvertently lost motive power. The contact was able to pull over to the shoulder of the roadway, where the vehicle was able to be restarted. No warning lights were illuminated. The…
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated while driving at an undisclosed speed, the vehicle inadvertently lost motive power. The contact was able to pull over to the shoulder of the roadway, where the vehicle was able to be restarted. No warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the battery. The vehicle was repaired, but the failure reoccurred. The vehicle was taken to the dealer, who then diagnosed a failure with the alternator. The vehicle was repaired. The manufacturer was not notified of the failure. The failure mileage was unknown.
- Engine · Power train
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated that while at a stop light, the vehicle independently shifted to neutral(N) for approximately 5 minutes. The vehicle failed to release from neutral when the driver shifted the gear shifter. The contact stated that the transmission…
The contact owns a 2017 Mercedes-Benz GLC300. The contact stated that while at a stop light, the vehicle independently shifted to neutral(N) for approximately 5 minutes. The vehicle failed to release from neutral when the driver shifted the gear shifter. The contact stated that the transmission then released from neutral(N), and the vehicle jolted forward. The check engine warning light was illuminated. The vehicle was taken to an independent mechanic, who was unable to determine the cause of the failure. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 75,000.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Front Roof Panel Detachment
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class…
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010644Complaint Paint damage on door paneling in area of door handle (see picture 1). Cause Possible tolerance complaint regarding the door handle Remedy 1. Paint the affected area of the door paneling using the spot repair procedure in accordance with the manufacturer's specifications. 2. Replace door handle, ensuring that the door handle bearing bracket is installed correctly (see picture 2). Note: The optimized door handles are marked as shown in the illustration (see picture 3).
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11000598Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case.
- 10253722Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Model year 2015-2018 Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2015-2018 vehicles. Model year 2019 Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 10252835Always use the latest XENTRY Diagnosis software release with all available add-ons. Make sure to follow the operation steps exactly as described in XENTRY Diagnosis. Use a battery charger to ensure sufficient power supply of the vehicle on-board electrical system battery (greater than 12.5 V). If XENTRY Diagnosis is already connected to the vehicle, start with operation step 2. If two or more software updates or SCN codings are performed during one workshop visit, operation items 02-4762 and 02-5058 may be invoiced only once for each workshop order. Work procedure 1. Connect XENTRY Diagnosis. 2. Update N129/1 - power electronics (SG-EM) control unit software. To do this, select menu item "Quick test view N129/1 - power electronics (SG-EM) Adaptations Control unit update Update of control unit software". Then follow the user guidance in XENTRY Diagnosis. 3. Disconnect XENTRY Diagnosis.
- 10251356The radio station favorites list is no longer present after bus idle Saving process during download Perform software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00).
- 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10243565In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the intake line assembly on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2015 - 2020 C/E/GLC/SLC and SLK vehicles, under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended, resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valve might also increase exhaust gas emission. . Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
- 10243308Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. Do not perform software update of N3/10 Engine control unit at this time. This LI will be updated once the software solution is available. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10241531In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the intake line assembly in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: Under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended,resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valvemight also increase exhaust gas emission. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has amalfunction. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 0101D Solenoid valve, crankcase ventilation system Part(s): A 274 090 5600 80 Intake Line Assembly (inclusive of oil separator, partial load ventilation valve and full-load ventilationvalve.) Where applicable, an ECU software update will be provided for certain vehicle variants. Time Allowed: Intake Line Assembly : 5 hours 40 minutes Software Update: 1 hour Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty.
- 10238437Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (MY) 2016 2021 C-Class (205 platform), E-Class (213 platform) and GLC (253 platform) vehicles, the air conditioning control unit software may not meet production specifications. There is a possibility that a stuck open thermostat may wrongly be detected causing the check engine Malfunction Indicator Lamp (MIL) to illuminate. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will perform a software update to the air conditioning control unit on the affected vehicles.
- 10238424In the MBUX weather app, the temperature is displayed in the wrong unit (Fahrenheit instead of C, or vice versa). Temperature setting in Mmc mobile application settings incorrect Remedy Adjust the setting in the Mercedes me connect app via mobile phone (settings -> units)
- 10231024Complaint - AIRMATIC fault message in instrument cluster - Compressor inoperative, 40A compressor fuse possibly triggered. - Vehicle level is not adjusted correctly, the vehicle possibly leans at an angle Cause Moisture in the compressor freezes at temperatures below zero and may block the compressor. As a result, the starting current when the compressor starts up is too high. Fuse is triggered Remedy Replace compressor, fuse, and relay. Update software and SCN coding. Please invoice the case using damage code 32671 73. Addition: Unscrew pressure line between compressor and valve block and check for moisture. If there is moisture in the pressure line, it can be assumed that there is also moisture in the AIRMATIC valve block. Replace AIRMATIC valve unit.
- 10227145Complaint Staining on door trim strips and top and bottom trim elements on rear side windows Cause Damage to protective coating (due to poor original optimization of coating) of door beltline trim strips, door upper trim strips and side window trim element. Remedy 1. Check if the complaint cannot be rectified by polishing the trim bars with the polish. 2. If the complaint cannot be rectified, replace the door beltline trim bars, door upper trim bars and rear side window with trim element with optimized protective coating.
- 10227142Complaint 1. Vibrations noticeable at steering wheel when front axle is excited when driving at a speed between 65 km/h and 130 km/h over an obstacle. Driving over deeply recessed manhole covers Driving over cross joints Driving over extreme surface undulations 2. Permanent or long-lasting vibrations at specific speed or engine speed noticeable on steering wheel. Roadway surface excitations when DTR+Q is switched on Cause Control oscillations in the electric power steering
- 10225820Complaint Staining on door trim strips and top and bottom trim elements on rear side windows Cause Damage to protective coating of door beltline trim strips, door upper trim strips and side window trim element due to strong alkaline detergent in car washes. Remedy 1. Check if the complaint cannot be rectified by polishing the trim bars with the polish. 2. If the complaint cannot be rectified, replace the door beltline trim bars, door upper trim bars and rear side window with trim element with optimized protective coating.
- 10222481Complaint Customer states after a bus sleep the SiriusXM category changes from "My Favorites" to "All Stations" or a different category. Sometimes, the "My Favorites" category will be unavailable for the entire drive cycle. Cause Current MBUX Multimedia System (A26/17) software release Remedy Software update of MBUX Multimedia System (A26/17) to E905.4 (in development). This document will be updated once the software is released.
- 10222462Complaint Malfunction of the electric steering column adjustment. The adjustment application by the driver does not correspond to the adjustment direction of the steering column. Cause Polarity reversal of the lines M20/1 (steering column adjustment motor, forward and backward) and M20/2 (steering column adjustment motor, upward and downward) results in a malfunction of the electric steering column adjustment. Remedy Check the lines (line colors) of M20/1 and M20/2 as per the WIS circuit diagram and correct if necessary.
- 10222461Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Replace repair kit for steering column height adjustment 2. Perform software update of driver's seat control unit
- 10219254Complaint In an initial quick test, DTC B238A00 "Fan 2 of the control unit has malfunctioned" may be active and/or stored in the MBUX Multimedia System (A26/17) Cause Current MBUX Multimedia System (A26/17) software release Remedy If there is no customer complaint present, the DTC can be ignored. A future MBUX Multimedia System (A26/17) software release (E905.3) will prevent the DTC from occurring. This document will be updated when the software is available.
- 10217216Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has extended the warranty for the accelerator pedal wiring harness and connectors from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles for certain Model Year (MY) 2016-2019 Mercedes-Benz E-Class and GLC-Class vehicles (213, 238, and 253 platforms).
Every Mercedes-Benz GLC300 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.