2022 Mercedes-Benz GLC 300
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › GLC 300 › 2022
These records cover every 2022 Mercedes-Benz GLC 300. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
2 recalls name the 2022 Mercedes-Benz GLC 300. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2022 GLC 300, 2020 GLC 350e, and 2020-2022 AMG GLC 43 vehicles. The headlights may be incorrectly adjusted too high and create a glare for oncoming traffic. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices…
Risk and remedy
Risk
Incorrectly aimed headlights can reduce the visibility of oncoming traffic, increasing the risk of a crash.
Remedy
Dealers will inspect the headlight adjustment and correct it if necessary, free of charge. Owner notification letters were mailed February 23, 2024. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2023 C-Class, E-Class, S-Class, CLS, SL, GT, GLC, GLE, GLS, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, which can result in a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 14, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023070012.
Owner complaints
61 complaints6 involved a crash2 involved a fire7 injuries1 deaths
What owners report most
Latest complaints
- Air bags
I am reporting a potentially serious vehicle safety issue involving a 2022 Mercedes-Benz GLC after a fatal crash. I was seated in the left rear seat. One occupant died and multiple people were injured. According to the Florida Highway Patrol crash report, the left curtain air bag was listed as…
I am reporting a potentially serious vehicle safety issue involving a 2022 Mercedes-Benz GLC after a fatal crash. I was seated in the left rear seat. One occupant died and multiple people were injured. According to the Florida Highway Patrol crash report, the left curtain air bag was listed as “Equipped; Not Deployed,” while the right curtain air bag was listed as “Equipped; Operative; Deployed.” I suffered serious injuries while seated on the same side where the curtain air bag did not deploy. Before the crash, I remember hearing an unusual metallic rattling/clanking noise from the vehicle. I do not know what caused the noise or whether it contributed to the crash, but it occurred before impact. A family member later reported this pre-crash noise to the vehicle’s insurer. Law enforcement indicated that the vehicle’s event data recorder (EDR/“black box”) would be downloaded, but the crash report later stated “EDR Downloaded: No.” To my knowledge, the EDR data was never retrieved or preserved. The insurer later sold the vehicle as salvage before I was able to arrange an independent defect inspection, so the vehicle is no longer available to me for examination. I am not claiming that a defect has been proven. I am asking NHTSA to review whether the documented left-curtain nondeployment, in a crash severe enough to cause a fatality and multiple injuries while the opposite curtain air bag deployed, warrants investigation of the air bag/restraint system or another vehicle component. I am also asking NHTSA to consider the pre-crash metallic noise and the loss of access to the vehicle and EDR data when evaluating this complaint. Because the vehicle and EDR evidence may no longer be recoverable, I respectfully ask NHTSA to evaluate this complaint promptly and compare it with any similar air bag, restraint-system, sensor, or electrical complaints involving this model.
- Fuel/propulsion system
The vehicle has experienced two separate incidents of significant loss of power/acceleration. First incident – January 2024, Clarksville, TN: While driving downtown, the vehicle suddenly lost significant power and could not provide normal acceleration. The estimated remaining range was…
The vehicle has experienced two separate incidents of significant loss of power/acceleration. First incident – January 2024, Clarksville, TN: While driving downtown, the vehicle suddenly lost significant power and could not provide normal acceleration. The estimated remaining range was approximately 50 miles. The vehicle was subsequently inspected/serviced by Mercedes-Benz/dealer personnel, but the underlying cause was not conclusively identified or resolved. Second incident- [XXX] [XXX]: While driving in the first lane of [XXX], the vehicle suddenly lost significant power/acceleration when the estimated remaining range was approximately 75 miles. There were no warning alarms or messages before the loss of power. My wife and child were in the vehicle. The vehicle could not provide normal acceleration in highway traffic, creating an extremely dangerous situation. The incident nearly resulted in a serious traffic accident, and my wife had to take immediate action to help avoid a potential collision. The vehicle was subsequently inspected by Mercedes-Benz/dealer personnel, but the specific loss-of-power condition was not conclusively reproduced or confirmed under the circumstances in which it occurred, and the underlying cause was not identified or resolved. The vehicle has therefore experienced this type of serious power-loss condition twice despite service attempts. I can no longer safely drive or intentionally test the vehicle to reproduce this condition. Attempting to drive until approximately 75 miles of remaining range could cause another sudden loss of power and potentially result in a serious accident. I will not intentionally recreate a potentially dangerous failure on a public highway with my family or other motorists at risk. I am reporting this because unexpected loss of power while traveling on a highway presents a serious safety hazard and potential collision risk. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Fuel/propulsion system
After recalls performed trouble code P2402 EVAP leak still is present and check engine light is on
- Unknown or other
Rear hatchback for 2026 Mercedes GLC sensors
- Electrical system · Service brakes
Vehicle: 2022 Mercedes-Benz GLC 300 4MATIC Component: Electronic Parking Brake (EPB) / Service Brakes Summary of Complaint: This vehicle has an ongoing, unresolved Electronic Parking Brake (EPB) defect. The amber EPB warning light has recurred multiple times, including most recently after a…
Vehicle: 2022 Mercedes-Benz GLC 300 4MATIC Component: Electronic Parking Brake (EPB) / Service Brakes Summary of Complaint: This vehicle has an ongoing, unresolved Electronic Parking Brake (EPB) defect. The amber EPB warning light has recurred multiple times, including most recently after a $3,000 dealership repair intended to correct this exact fault. Timeline: 1.Following a brake pad replacement, the vehicle experienced an EPB failure, brake fluid loss, and a gear shift interlock lockout — leaving the vehicle inoperable. 2.The vehicle was taken to a Mercedes-Benz dealership for repair. This resulted in a dispute over unauthorized work performed and a request for goodwill coverage tied to a known Mercedes-Benz EPB recall. 3.I paid approximately $3,000 to the dealership for a repair specifically to resolve the EPB fault. 4.Approximately a few weeks after this paid repair, the same amber EPB warning light returned, indicating the underlying defect was not resolved. Safety Concern: The EPB is a safety-critical system. Repeated, unresolved failure of this system — including a prior incident involving brake fluid loss and a gear shift interlock lockout that left the vehicle inoperable — represents a real risk of parking brake failure and loss of vehicle control/immobilization in normal use. Additional Notes: •This defect appears connected to a known Mercedes-Benz EPB recall. •I have photo documentation of the recurring warning light (dated) and the dealership repair invoice for the $3,000 repair. •I have an open case with Mercedes-Benz Customer Assistance regarding this issue.
- Engine · Fuel/propulsion system
My 2022 Mercedes-Benz GLC 300 (17,700 total miles) suffered a catastrophic structural engine block failure and an explosive loss of propulsion while driving at highway speeds. This occurred exactly 6 days and 183 miles after a franchised Mercedes-Benz dealership performed the official fuel pump…
My 2022 Mercedes-Benz GLC 300 (17,700 total miles) suffered a catastrophic structural engine block failure and an explosive loss of propulsion while driving at highway speeds. This occurred exactly 6 days and 183 miles after a franchised Mercedes-Benz dealership performed the official fuel pump impeller safety recall (NHTSA Campaign 23V-445).The dealership's official repair invoice documents that the technician custom-modified the recall remedy by reusing parts, explicitly stating: 'Relocated floater from old pump onto new fuel pump.' Simultaneously with the mechanical engine failure, a 'Reduce Engine Oil Level' message flashed on the dashboard, indicating severe fuel dilution from the compromised fuel system.The dealership is actively violating federal recall mandates by refusing to investigate this failed safety remedy unless I sign an open-ended financial check for a diagnostic and teardown fee. They have also revoked my substitute transportation to coerce payment. Mercedes-Benz USA Corporate Case Number 23652724 has been opened. I am requesting a federal safety investigation into this dealer's non-compliant recall remedy execution."
- Vehicle speed control
I have experienced 4 incidents of the car accelerating on its own. I have taken it to the dealership twice and they are unable to reproduce the problem. Problems began occurring in 2025 and occurred again this past week (August 20246). In the most recent incident I was accelerating on an "on ramp".…
I have experienced 4 incidents of the car accelerating on its own. I have taken it to the dealership twice and they are unable to reproduce the problem. Problems began occurring in 2025 and occurred again this past week (August 20246). In the most recent incident I was accelerating on an "on ramp". The car suddenly took hold and continued to speed up despite my foot not being on the gas. I had to drive the car to safety with my foot on the break. The moment I took my foot off the break it would speed up. The floor mat was not touching the gas in all of the instances of this occurring. The gas pedal was not stuck to anything. I nearly avoided a serious accident as where i was trying to merge was running out of a lane and a cement block was in front of me. I was also with an infant and 2 year old in my car. There have been no warning messages when this occurs.
- Electrical system · Engine · Service brakes
While driving down a busy neighborhood street 2 lanes with cars on both sides making it a 1 lane road pulled over to the side a little to let cars pass. All of a sudden ALL electrical and engine stopped and turned off. Only thing that was powered was instrument cluster with multiple warnings like…
While driving down a busy neighborhood street 2 lanes with cars on both sides making it a 1 lane road pulled over to the side a little to let cars pass. All of a sudden ALL electrical and engine stopped and turned off. Only thing that was powered was instrument cluster with multiple warnings like SRS Malfunction, Steering Malfunction, SOS Inoperative, Parking Brake and more. We believe the car had also shifted to park on its own. No power to anything not even hazard lights. Nothing electrical had any sort of power. Could not even turn car off completely could not get the instrument cluster to turn off with ignition button. When I say everything electrical had no power I mean everything except instrument cluster. Hazard lights power locks, lights of any kind, ignition switch, gear selector, windows, sos feature, nothing had power. I could not imagine having this issue driving on the interstate and having the car completely loose ALL electrical power and what could happen to specially with a SRS malfunction and issue with steering. Had to have a wrecker come with wheel dollys because car could not be put in neutral and towed to Mercedes dealer. Upon their inspection they found the Circuit 30T relay to be stuck in the open position which killed power to everything so the technician replaced the engine compartment pre-fuse panel. It is such a unsafe and very hazardous issue to have a relay failure to where all power is lost especially if you were driving on interstate especially at night with traffic to loose everything electrical even hazard lights and headlights, SRS maltunction, Steering. Mercedes needs to figure this very unsafe issue out.
- Electrical system · Service brakes
My vehicle got stuck on a EPB(electronic parking brake) and I was unable to disengage it. I tried a few things and none worked. I contacted Mercedes to tow it to the dealer and the tow truck came and driver had to “drag” my vehicle on to the flatbed. My car has been at Mercedes for 5 days now and…
My vehicle got stuck on a EPB(electronic parking brake) and I was unable to disengage it. I tried a few things and none worked. I contacted Mercedes to tow it to the dealer and the tow truck came and driver had to “drag” my vehicle on to the flatbed. My car has been at Mercedes for 5 days now and they gave me a response saying that they are having a hard time trying to disengage the EPB. I’m aware of a EPB recall but my model is specified as being a part of it, however the issue is closely related to the recall so please take further interest in my situation because it could be the start of a new recall. The dealer says they have tried and failed to disengage it. My car was working just fine so please take further look at a possible software glitch for the EPB.
- Electrical system · Engine · Fuel/propulsion system
Low coolant warning came on. Battery car didn’t start , had it jump. Low coolant warning came on again. Passenger seat belt warning is on.
- Fuel/propulsion system
I was driving back to my house in york, PA. My car all the sudden changed the gear from “D” to “N”. My gas meter was showing 106 miles. my didn’t give sign or alert before it shifted the gear from D to N. I was driving on highway and this was major safety concern as I could have hit by cars coming…
I was driving back to my house in york, PA. My car all the sudden changed the gear from “D” to “N”. My gas meter was showing 106 miles. my didn’t give sign or alert before it shifted the gear from D to N. I was driving on highway and this was major safety concern as I could have hit by cars coming on highway speed. We had this similar incident last year as well but we were at traffic light stopped so we didn’t realize that time that car shift the grear by itself. Once we fill the gas, we were able to drive back home but it was scary and big safety concern that car doesn’t give any notification or alert for low fuel and change gear all the sudden.
- Engine and engine cooling
See attached document for complaint.
- Fuel system, gasoline
The contact owns a 2022 Mercedes-Benz GLC300. The contact stated that while driving at various speeds and depressing the accelerator pedal, the check engine warning light was displayed on the instrument panel. The vehicle lost power and was pulled over and restarted. The contact was almost involved…
The contact owns a 2022 Mercedes-Benz GLC300. The contact stated that while driving at various speeds and depressing the accelerator pedal, the check engine warning light was displayed on the instrument panel. The vehicle lost power and was pulled over and restarted. The contact was almost involved in several crashes due to the failure. The vehicle was included in NHTSA Campaign Number: 23V445000 (Fuel System, Gasoline); however, the vehicle was repaired, and the failure persisted. The vehicle was taken to the dealer on several occasions, where the fuel pump, charcoal filter, and other various parts of the fuel pump were repaired; however, the failure persisted. The manufacturer was notified of the failure, and the contact was informed that the cylinder head would be replaced free of charge. The contact believed that the vehicle was unsafe to drive due to the failures. The vehicle was not repaired, and a loaner vehicle was provided. The failure mileage was unknown.
- Unknown or other
My vehicle had check engine lights on throughout the last couple of years. Every time I bought it to the dealer, they ignored it and said the light went off. The machine doesn't pick up anything. Now the check engine light is on and the cylinder head and diagnostic head, something is wrong. They…
My vehicle had check engine lights on throughout the last couple of years. Every time I bought it to the dealer, they ignored it and said the light went off. The machine doesn't pick up anything. Now the check engine light is on and the cylinder head and diagnostic head, something is wrong. They will fix the diagnostic head but not the cylinder head. The dealership knew there was ongoing issues but did nothing to correct it. The sales department already screwed me as well. The older models are recalled for the same issues and now the the newer vehicles like mine are having the same EXACT problem.
- Engine
The contact owns a 2022 Mercedes-Benz GLC300. The contact stated that while driving at an undisclosed speed, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. There was a misfire coming from the engine, and the vehicle lost motive power. In addition, the…
The contact owns a 2022 Mercedes-Benz GLC300. The contact stated that while driving at an undisclosed speed, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. There was a misfire coming from the engine, and the vehicle lost motive power. In addition, the check engine warning light illuminated. The vehicle was taken to the dealer, where it was diagnosed with spark plug failures, coils, and the transmission needed to be flushed. The vehicle was taken to an alternate dealer where the spark plugs and coils were replaced, and the transmission fluid was flushed. The contact stated that the failure reoccurred. The vehicle was then taken to an independent mechanic who was a Mercedes mechanic, where it was diagnosed with misfire codes in cylinders #1 and #4, leakage coming from exhaust valves in cylinders #1 and #4, low compression in cylinders #1 and #4, and there was a 75 percent leak in cylinders #1 and #4. The contact was informed that the complete head assembly needed to be replaced. The vehicle was not repaired. In addition, the contact stated that the vehicle was repaired under NHTSA Campaign Number: 23V445000 (Fuel System, Gasoline) on 11/2025. The contact stated that the failure began shortly after the recall repair was performed. The manufacturer was not made aware of the failure. The failure mileage was unknown.
- Unknown or other
On Saturday 12/6/25, I put my 15 year old cat in his carrier in the back seat and closed the door. I got into my car and opened my garage door. I started my MBGLC300 and began backing my car out of my garage. As soon as the car rear end cleared the garage, I heard an explosion "BOOM", and the…
On Saturday 12/6/25, I put my 15 year old cat in his carrier in the back seat and closed the door. I got into my car and opened my garage door. I started my MBGLC300 and began backing my car out of my garage. As soon as the car rear end cleared the garage, I heard an explosion "BOOM", and the sound of breaking glass. I pulled back into my garage only to find the entire back window had exploded... all the glass was gone, and the back windshield wiper was dangling out of its housing from the pane (trim). I hit nothing! Nothing hit me! I got back into my car and drove the 10 minutes down the street to my vet's where he got his shot and I had him combed out (for any glass - thank goodness there wasn't any). While there, I phoned Dick Dyer Mercedes Benz (803.828.6952) at 8:57 AM,and spoke with Ryan Smith and told him I'd be down after the vet appointment. I pulled in at Dick Dyer service department shortly after 9:00AM. He said, "I've never seen anything like this." The whole glass was shattered into millions of tiny pieces. Smith got me into a Sedan and I drove home. On Monday Smith called to tell me Mercedes would not honor either my factory warranty (my car is a 2022) nor would my Extended Warranty (purchased at the time I bought my car) cover the $4,201.00 charge to repair. I'm a school teacher. I don't have that amount of cash. He said, "Ms. [XXX] , I want to believe you that you didn't hit anything, but I have to have proof." Therefore my only way to get the car repaired is to go through my insurance company. What a rip off! I totally thought Mercedes was a company that would stand by their products, especially those under not just 1 factory warranty, but a 2nd extended warranty. And, I got called a liar to boot. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Air bags · Forward collision avoidance › Warnings · Service brakes
I was involved in a severe front-end collision where my vehicle struck another vehicle with significant force. Despite the major impact, the front airbags did NOT deploy. The entire front end of the vehicle was crushed, including destruction of the radiator, damage to engine components, internal…
I was involved in a severe front-end collision where my vehicle struck another vehicle with significant force. Despite the major impact, the front airbags did NOT deploy. The entire front end of the vehicle was crushed, including destruction of the radiator, damage to engine components, internal structural collapse, and leaking fluids. Based on the severity and direct frontal nature of the crash, airbags should have deployed but did not. As a result of the impact, I sustained a neck and upper shoulder injury and required medical evaluation. There were no warning lights or messages prior to the crash indicating any malfunction in the airbag or SRS system. The vehicle is available for inspection by NHTSA, the manufacturer, insurance, or an authorized Mercedes-Benz service center. This appears to be a possible failure of the airbag/SRS system during a qualifying collision.
- Back over prevention › Sensing system › Camera
The rearview camera on my vehicle intermittently fails to function for unknown reasons, and the problem has recently become more frequent. For example, it may work normally when I first start the car in the morning and back out of my parking spot, but later the same day—such as when I arrive at…
The rearview camera on my vehicle intermittently fails to function for unknown reasons, and the problem has recently become more frequent. For example, it may work normally when I first start the car in the morning and back out of my parking spot, but later the same day—such as when I arrive at work—the camera stops working completely. The display stays black and does not recover even after shifting between gears or restarting the system. After parking and locking the car for a while, the camera may start working again without any clear reason. Although I cannot recall the exact dates of the first occurrence, I have noticed a consistent pattern over time: the issue tends to appear during hot weather, particularly in summer. In recent months, the camera has almost completely stopped functioning. This unpredictable failure creates a potential safety hazard when reversing, as I cannot get help on the backup camera to provide visibility behind the vehicle.
- Steering · Unknown or other
Loss of Steering Control at Highway Speeds – 2022 Mercedes-Benz GLC300 Vehicle: 2022 Mercedes-Benz GLC300, VIN [XXX] Dates of Incident: September 13th and October 4th Mileage at Time of Incident: 39,500 While driving on a four-lane expressway at highway speeds, my vehicle suddenly and completely…
Loss of Steering Control at Highway Speeds – 2022 Mercedes-Benz GLC300 Vehicle: 2022 Mercedes-Benz GLC300, VIN [XXX] Dates of Incident: September 13th and October 4th Mileage at Time of Incident: 39,500 While driving on a four-lane expressway at highway speeds, my vehicle suddenly and completely lost steering control, resulting in a total inability to steer. First Incident The first event occurred during light rain with mildly wet road conditions. Without warning, the vehicle hydroplaned and violently crossed all four lanes approximately 20–25 times, narrowly avoiding collisions with other vehicles and medians. The steering wheel was completely unresponsive. After several minutes, the car inexplicably corrected its course. Second Incident The second incident occurred weeks later under clear, dry conditions with my minor child in the car. Once again, the steering wheel locked, leaving me unable to direct the vehicle. I had to physically force the wheel to prevent the car from leaving the highway. Investigation The car was towed to Mercedes-Benz of Coral Gables, where technicians were unable to find any fault despite multiple diagnostic attempts. I have since discovered that 2023 and 2024 models of this same vehicle are under active recall for a similar steering malfunction, which may indicate that 2022 models are also affected. Safety Concern This defect poses an imminent risk of fatal accidents, both to occupants and to other drivers. The failure occurs without warning, at high speeds, and results in total loss of steering control. Requested Action I request that the NHTSA investigate whether 2022 models should be included in the existing recall related to steering control failure in Mercedes-Benz vehicles. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Steering
I was driving home on a 4 Lane Expressway on a Saturday afternoon, it was mildly raining with the roads a little wet. I suddenly lost control of the car and could not control the steering wheel, the car ended up hydroplaning and I lost control it ping-ponged across four expressway lanes…
I was driving home on a 4 Lane Expressway on a Saturday afternoon, it was mildly raining with the roads a little wet. I suddenly lost control of the car and could not control the steering wheel, the car ended up hydroplaning and I lost control it ping-ponged across four expressway lanes back-and-forth about 20 to 25 times with zero control of the steering wheel, barely missing the medians and other cars. It should have been a massive catastrophe. Cars around me you had to stop and swerve around me to avoid hitting me all while driving on the expressway. Had someone accidentally hit me in the process it would’ve certainly flipped the car and I would’ve either ended up dead or in the ICU. After several minutes somehow without moving the steering wheel, I managed to just go straight and pull over. And waited for help to get back safely slowly. I thought the incident was isolated because the roads might have been the cause. But I went out out of the country and upon coming back, drove my car again on the expressway coming back home and the exact same thing happened with my minor child in the car across two expressway lanes in the evening time With the roads perfectly dry. Lost control of the steering wheel could not steer or direct the car and had to jerk it from to prevent it from driving off the highway. It seemed to have occurred both times at a higher velocity on expressways when the steering wheel needed to be engaged. I had it towed to the Mercedes Benz Of Coral Gables dealership, but they cannot find anything wrong with the car, even though the exact same model of my car has an active recall for 2023 and 2024 models. For the same problem, I later learned. Mine is a 2022. I have been in a loaner vehicle for three weeks while they investigate and I need Assistance to make sure that something gets done because nothing has been found and I do not want to risk driving with my child in the car.
- Engine
Multiple loss of power incidents while driving both on surface streets and highways. Causes vehicle to loss acceleration power, vehicle must be pulled over, shut down and restarted to regain power.
- Power train
The contact owns a 2022 Mercedes-Benz GLC300. The contact stated that while driving 60 MPH, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. The contact stated that there were several unknown warning lights illuminated before the engine seized. The vehicle…
The contact owns a 2022 Mercedes-Benz GLC300. The contact stated that while driving 60 MPH, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. The contact stated that there were several unknown warning lights illuminated before the engine seized. The vehicle was restarted; however, while driving at an undisclosed speed, the failure reoccurred. The contact started the vehicle again, and the vehicle was slowly driven to the residence. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 51,519.
- Engine · Power train
Defect Summary: Since 2024, my 2022 Mercedes-Benz GLC300 has had a persistent, abnormal engine noise consistent with the sound of a 4-cylinder diesel engine, despite being gasoline-powered. The noise occurs both while idling and in motion. On several occasions, the coolant warning light illuminated…
Defect Summary: Since 2024, my 2022 Mercedes-Benz GLC300 has had a persistent, abnormal engine noise consistent with the sound of a 4-cylinder diesel engine, despite being gasoline-powered. The noise occurs both while idling and in motion. On several occasions, the coolant warning light illuminated while the noise persisted. The defect has worsened over time, becoming louder and more frequent. Events & Safety Risks: The dealership repeatedly claimed “no problem found” because no warning lights appeared and no scanner codes were present, ignoring my time-stamped video evidence. At one point, I was advised to drive the vehicle from Morgan Hill, CA to the dealership while making the loud noise for diagnostics — an unsafe recommendation. When the coolant warning light appeared, the service department planned only to top off coolant. I insisted on a diagnostic, which revealed a coolant hose leak. Driving with a leak could cause overheating and sudden engine failure, creating a serious safety hazard for myself, my child, and other motorists. Repair History: Multiple visits to Mercedes-Benz of San Jose (2024–2025) for the same defect. Each time, the defect was dismissed or not resolved. No meaningful repairs were performed. The issue persists today. Evidence: Time-stamped video proof of defect, full service records, and documentation of correspondence with the dealership are available. Safety Concern: This unresolved defect creates a risk of sudden engine failure or overheating while driving, potentially causing loss of control or stranding occupants in unsafe conditions.
- Engine · Fuel/propulsion system
My 2022 Mercedes-Benz GLC 300 has been diagnosed with a valve seat failure. This requires a full cylinder head replacement. I purchased this vehicle brand new and have driven it with care, putting approximately 60,000 mostly highway miles on it. Throughout my ownership, I have exclusively used the…
My 2022 Mercedes-Benz GLC 300 has been diagnosed with a valve seat failure. This requires a full cylinder head replacement. I purchased this vehicle brand new and have driven it with care, putting approximately 60,000 mostly highway miles on it. Throughout my ownership, I have exclusively used the service at an authorized Mercedes-Benz dealership. Despite my efforts to maintain this vehicle properly, the vehicle began exhibiting misfire issues just outside of the warranty period. The check engine light would flash on and off during a misfire and it presented multiple codes. I returned to a Mercedes-Benz dealership, where I was told the issue is an internal mechanical failure, worn or leaking valve seats requiring full cylinder head replacement with an estimated repair cost of $7,800. Upon researching this issue, I've learned that Technical Service Bulletins exist for this exact failure, and other owners with M264-series engines have experienced identical symptoms and failures. This misfire could happen at anytime, requiring me to stop the vehicle almost immediately. It could cause a dangerous situation in heavy traffic areas with fast moving traffic.
- Steering
The vehicle's steering wheel vibrates noticibly between speeds of 47 mph and 55 mph. This issue was once addressed with a "software update" by Mercedes Benz of Portsmouth, NH. Streering wheel vibration is a concern for any driver that rely on power steering to turn or hold the car steady. In…
The vehicle's steering wheel vibrates noticibly between speeds of 47 mph and 55 mph. This issue was once addressed with a "software update" by Mercedes Benz of Portsmouth, NH. Streering wheel vibration is a concern for any driver that rely on power steering to turn or hold the car steady. In addition it creates unnecessary panic for some drivers. This issue is brought to Mercedes Benz multiple times. I had replaced all the tires at 19,000 miles, balanced, got tires aligned by Mercedes Benz dealer and the issue persists.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010648Complaint Transfer of selected user-defined scene/ animation (Mercedes-Benz Phone App) from HU to ECU software fails to start. Charging bar stops at 0%. (Picture in attachment) Cause Communication between headlight control unit and HU. Remedy Update the software of the following control units to the latest version: - A26/17 - MBUX multimedia system (head unit) - E1n14 - Front left digital headlight control unit (DHLS-CU-VL) - E2n14 - Front right digital headlight control unit (DHLS-CU-VR)
- 11010644Complaint Paint damage on door paneling in area of door handle (see picture 1). Cause Possible tolerance complaint regarding the door handle Remedy 1. Paint the affected area of the door paneling using the spot repair procedure in accordance with the manufacturer's specifications. 2. Replace door handle, ensuring that the door handle bearing bracket is installed correctly (see picture 2). Note: The optimized door handles are marked as shown in the illustration (see picture 3).
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008056Complaint Check engine light on. Fault code P207273 - "Throttle actuator valve is blocked due to ice" stored. Engine may crank and not start. Fault code P210185 may also be stored. Cause Moisture freezing on throttle actuator during extreme low ambient temperatures. Remedy Update software of engine control module. Software increases throttle valve flapping after engine turned off to prevent moisture buildup.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11006710Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class (206 platform), EQE (294 and 296 platform), EQS (295 and 297 platform), GLC (254 platform), AMG GT (192 platform), S-Class (223 platform), and AMG SL (232 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The communication module will receive an OTA software update that includes product improvements. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers will be mailed a letter informing them of this software update.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005314Complaint Yellow Coolant warning comes on in cluster Fault codes below are current or stored in MED41 P0A0500- The actuation of the circulation pump for the low-temperature circuit has an open circuit. P00B700- The coolant flow is too low. P0C7300- Circulation pump 1 for the low-temperature circuit has a malfunction. Cause Air may be trapped in the coolant circuit for transmission cooler Remedy Check coolant level. -If coolant level is low, locate source of leak and correct. -If coolant level is ok, perform procedure in attached instructions to bleed the coolant circuit to transmission cooler. 1. Allow cooling system to cool to ambient temperature. 2. Fill coolant reservoir completely. 3. Slightly open coolant connection shown in attachment (red arrow) to allow air to escape. 4. Once coolant flows out, close connection and correct coolant level. 5. Clear fault codes and check for further symptoms.
- 11005313Complaint Check engine light on and fault code P019185 current or stored in MED41 control unit. Adaptation and misfire faults may also be stored. Vehicle may enter limp home mode. Cause False detection of rail pressure sensor out of range. Remedy Update software of engine control module N3/10. Reset mixture adaptation and clear fault codes.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11003212Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. 3. NOTE: Coding Parameter 'Shimmy' should be turned off and the actual value should read "Shimmy aus". With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11003205Complaint The driver's seat memory settings do not synchronize with the driver's user profile as described in the operator's manual. Driver's seat settings are not transferred to the vehicle. Cause The driver's seat does not support the profile synchronization feature on these vehicles. Remedy There is no remedy for this complaint. The vehicle is working as designed. Note: Do not replace any parts.
- 11000598Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case.
- 10253703This is to notify you of the Service Campaign OTA update for the MBUX system software in 750,313 Model Year (MY) MY19-24 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10252835Always use the latest XENTRY Diagnosis software release with all available add-ons. Make sure to follow the operation steps exactly as described in XENTRY Diagnosis. Use a battery charger to ensure sufficient power supply of the vehicle on-board electrical system battery (greater than 12.5 V). If XENTRY Diagnosis is already connected to the vehicle, start with operation step 2. If two or more software updates or SCN codings are performed during one workshop visit, operation items 02-4762 and 02-5058 may be invoiced only once for each workshop order. Work procedure 1. Connect XENTRY Diagnosis. 2. Update N129/1 - power electronics (SG-EM) control unit software. To do this, select menu item "Quick test view N129/1 - power electronics (SG-EM) Adaptations Control unit update Update of control unit software". Then follow the user guidance in XENTRY Diagnosis. 3. Disconnect XENTRY Diagnosis.
- 10252777Tailgate opens unintentionally. Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button
- 10251356The radio station favorites list is no longer present after bus idle Saving process during download Perform software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00).
- 10251192Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 21-24 C-Class, EQE, EQS, GLC, GLE, GLS, S-Class, SL (206, 294, 295, 296, 297, 254, 167, 223, 232 platform) vehicles, the MBUX System software does not correspond with the latest series production configuration. The MBUX control unit will receive an OTA update that includes functional improvements and new features such as: Dolby Atmos, video streaming, personalized images on the front passenger display, and additional commands for the MBUX Voice Assistant. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10251176Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY20-23 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update.
- 10249540Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2019-2023 A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.
- 10249495Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!
- 10249482The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.
- 10248203Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service for the navigation system. Additional product improvements including infotainment system robustness will be implemented. The software update will be downloaded in the background. The subsequent installation takes roughly 45 minutes and requires the customer's consent in the vehicle. During installation, the system can be used without restriction. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10248195Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10244748Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-23 C-Class, EQS, S-Class, SL, EQE, GLC (206, 296, 297, 223, 232, 294, 295, 254 platform) vehicles, the head unit software will be updated remotely to MBUX 2.4. With this update, customers will benefit from many new functions and features, such as video streaming (note that the Entertainment Package Plus is required for streaming and can be purchased from the Mercedes me Store by the end of 2023), Dolby Atmos, MBUX Voice Assistant (NewsFlash & Tourguide), a personal decorative image on the front passenger display, and more. Please see NCU issued on September 5th, 2023 from Product Management and Digital House team Additional New Connected Features Coming Soon. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. No customer letter will be mailed for this software update.
- 10244745Sliding sunroof panel of panoramic sliding sunroof reversed (temporarily, once, multiple times) during closing process without entrapment event. Sensitive parameterization of the automatic reversing function of the panoramic roof. Perform SW update of panoramic roof control unit (PSD, A98, TSSR254).
Every Mercedes-Benz GLC 300 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.