2019 Mercedes-Benz GLC 300
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › GLC 300 › 2019
These records cover every 2019 Mercedes-Benz GLC 300. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
12 recalls name the 2019 Mercedes-Benz GLC 300. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2022 GLC 300, 2020 GLC 350e, and 2020-2022 AMG GLC 43 vehicles. The headlights may be incorrectly adjusted too high and create a glare for oncoming traffic. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices…
Risk and remedy
Risk
Incorrectly aimed headlights can reduce the visibility of oncoming traffic, increasing the risk of a crash.
Remedy
Dealers will inspect the headlight adjustment and correct it if necessary, free of charge. Owner notification letters were mailed February 23, 2024. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel…
Risk and remedy
Risk
A detached roof panel can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the front panel, free of charge. Owner notification letters were mailed on August 2, 2024. Owner notification letters will be mailed in phases, on, March 22,2024, and August 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 21V-197.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019 AMG G63, C300, E300, G550, AMG GT63, AMG GT53, 2019-2020 A220, GLA250, GLC300, 2016 C300, 2020 AMG A35, AMG C43, AMG C63, CLA250, E350, E450, GLB250, GLE450, GLS450, GLS580, S560, and SL550 vehicles equipped with a gasoline engine. During the manufacturing process, particles may have been trapped…
Risk and remedy
Risk
A fuel leak in the presence of an ignition source, such as hot engine or exhaust components, can increase the risk of a fire.
Remedy
Dealers will replace the fuel rail and fuel injectors, free of charge. Owner notification letters were mailed April 22, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for the recall is 2022030003.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017…
Risk and remedy
Risk
The adhesive bonding of the front panel might deteriorate, possibly causing the front panel to detach from the vehicle and become a road hazard, increasing the risk of a crash.
Remedy
Mercedes-Benz dealer will remove the bonded panel and will install a new front panel by following the detailed repair instructions and using the approved primer, cleaner and adhesive, free of charge. Owner notification letters were mailed on September 3, 2021 and October 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2019 C300, E300, 2018-2020 CLA250, 2020 CLS450, AMG E53, AMG GT53, GLE450, 2018 AMG E63, AMG GTA, 2017-2020 GLA250, GLC300, 2019 GLC350, AMG GLC43, 2017-2018 GLE350, 2019 AMG GLC 43, GLC350, GLE400, 2017 GLS450, S550, C300 Cabrio, and 2018-2019 S560 vehicles. On June 18, 2021, an additional 9…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting emergency services through the call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the communication module and activate it, if necessary, free of charge. The recall began March 31, 2021. Letters for the owners of the 9 additional vehicles were mailed July 9, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021030005.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2019 GLC 300 4MATIC coupe, AMG GLC 43 Coupe, AMG GLC 43, AMG GLC 63, GLC 300, GLC 350e 4MATIC, GLC300 4MATIC, AMG GLC 63 Coupe, and AMG GLC 63 S Coupe vehicles. The passenger side sun visor may have incorrect air bag warning labels, written in a foreign language. As such, these vehicles fail to comply…
Risk and remedy
Risk
If an air bag label is in a foreign language, an occupant may not be aware of the risks to children sitting in the front seat, increasing the risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect the air bag warnings and replace them, as necessary, free of charge. The recall began March 3, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020020014.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2019 GLC300 and GLC300 4MATIC vehicles. The electrical connection between the power steering electric motor and the control unit may fail, resulting in the loss of electric power steering assist.
Risk and remedy
Risk
A loss of power steering assist would require a greater steering effort to control the vehicle, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the electric power steering control unit, free of charge. The recall began December 20, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019110014.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2018 E400 Wagon 4MATIC, E400 4MATIC, E43 AMG 4MATIC, 2018-2019 E63S AMG 4MATIC Wagon, E63 AMG 4MATIC Wagon, E300, E300 4MATIC, GLC63S Coupe AMG 4MATIC, 2019 CLS450, CLS450 4MATIC, CLS53 AMG 4MATIC, E450 Wagon, E53 AMG 4MATIC, GLC300, GLC63 AMG Coupe 4MATIC, G550 4MATIC, G63 AMG, GLC300 Coupe 4MATIC…
Risk and remedy
Risk
The electric PRE-SAFE®-function and the seat belt pretensioners may not deploy during a crash, increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the front seat belt buckles, replacing them as necessary, free of charge. The recall began March 13, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020020017.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018 C300 Cabriolet, C300 Coupe, C300 4Matic Cabriolet, C300, C300 4Matic Coupe, C300 4Matic, C43 AMG Cabriolet, C43 AMG Coupe, C63 S AMG Cabriolet, C350e Plug-In Hybrid, C63 AMG Cabriolet, C63 AMG Coupe, C63 S AMG Coupe, C63 AMG, C63 S AMG, 2018-2019 GLC300 4Matic Coupe, GLC300, GLC63 AMG Coupe, GLC300…
Risk and remedy
Risk
If the passenger air bag is incorrectly displayed as 'ON' when it is not, a front seat passenger may be unaware that the air bag will not deploy in the event of a crash, increasing their risk of injury.
Remedy
MBUSA will notify owners, and dealers will update the audio head unit software, free of charge. The recall began January 3, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018120009.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019 GLC300 vehicles. An internal sensor within the electric power steering unit may fail, deactivating the power steering assist.
Risk and remedy
Risk
A loss of electric power steering assist can increase the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the steering unit, free of charge. The recall began June 7, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA'S number for this recall is 2019040007.
Owner complaints
47 complaints4 involved a crash2 involved a fire4 injuries
What owners report most
Latest complaints
- Unknown or other
vehicle: 2019 Mercedes-Benz GLC 300 Component Involved: Integrated Transmission Control Module (TCM) / Mechatronic Unit Active Diagnostic Code: P073E (Unable to Engage Reverse) Description of Event: While attempting to back out of a driveway, the vehicle experienced a sudden, catastrophic…
vehicle: 2019 Mercedes-Benz GLC 300 Component Involved: Integrated Transmission Control Module (TCM) / Mechatronic Unit Active Diagnostic Code: P073E (Unable to Engage Reverse) Description of Event: While attempting to back out of a driveway, the vehicle experienced a sudden, catastrophic electronic transmission failure. Without any warning or prior symptoms, the vehicle abruptly kicked itself out of gear and dropped into Neutral. The vehicle completely lost all propulsion and ability to move backward or forward, rendering it entirely disabled. This failure occurred directly in the path of oncoming traffic, creating an immediate, life-threatening safety hazard for myself, my passengers, and other drivers. Due to the complete loss of gear engagement, we were trapped in a highly dangerous and vulnerable position. A subsequent scan of the vehicle’s onboard computer revealed active diagnostic code P073E (Unable to Engage Reverse), indicating a documented internal failure within the 9G-Tronic mechatronic/transmission control unit. The vehicle is currently completely unsafe to operate and has been parked in a residential garage to prevent a severe collision. Given that this is a sudden component defect that results in an immediate loss of vehicle control rather than standard wear-and-tear, this issue represents a critical manufacturing safety hazard that requires immediate corporate intervention.
- Electrical system · Power train
On April 16, 2026, within minutes of being released from a certified dealership, my 2019 Mercedes-Benz GLC 300 suffered a sudden and total loss of propulsion while traveling at high speed on the Belt Parkway (NY). Despite depressing the accelerator, the vehicle failed to maintain speed and stalled…
On April 16, 2026, within minutes of being released from a certified dealership, my 2019 Mercedes-Benz GLC 300 suffered a sudden and total loss of propulsion while traveling at high speed on the Belt Parkway (NY). Despite depressing the accelerator, the vehicle failed to maintain speed and stalled in active traffic. This created an immediate life-safety hazard, forcing me to navigate across multiple lanes without engine power to avoid a high-speed rear-end collision. The vehicle was released to me by Mercedes-Benz of Brooklyn on April 16, 2026, following a repair for which I paid $2,134.94. The dealership diagnosed the issue as a wiring harness/sensor fault and formally certified the vehicle as "Found OK" and safe for operation. The catastrophic failure occurred only 22 minutes after I departed the dealership lot. The vehicle had to be towed back to the facility immediately. Upon the vehicle being towed back on April 16, the dealership admitted via recorded voicemail that the initial $2,134.94 repair was a misdiagnosis. They subsequently issued a new diagnosis for a "Valve Body" failure and a new quote of $6,424. The dealership's Service Director has since admitted the vehicle suffers from concurrent transmission and engine failures, rendering the car a liability. This represents a critical failure of the powertrain and electronic control systems. Releasing a vehicle that suffers a total power loss on a highway immediately after a "certified" repair is gross negligence. I am reporting this to NHTSA as a catastrophic failure of a safety-critical component (Transmission/Valve Body) that resulted in a "dead-stick" situation on a major New York thoroughfare, posing a severe risk to myself and other motorists. The vehicle remains at the dealership. Mercedes-Benz USA has offered only a $2,000 "goodwill credit," which does not address the safety defects or the initial misdiagnosis. No recall has been initiated for this batch.
- Visibility › Sun/moon roof assembly
The contact owns a 2019 Mercedes-Benz GLC300. The contact stated that while driving 65 MPH on the interstate, the sunroof suddenly shattered into pieces and flew off the vehicle. The vehicle was driven to a dealer but was not repaired. The manufacturer was notified of the failure. The failure mileage was 106,706.
- Unknown or other
I have a MC Benz 300 GLC with $50,000 miles. I was having heating issues so took it to the dealership, which basically advised of the issue describer below, which would cost $14k to repair. Contaminated coolant in Mercedes-Benz GLC 300 models often results from the internal failure of a…
I have a MC Benz 300 GLC with $50,000 miles. I was having heating issues so took it to the dealership, which basically advised of the issue describer below, which would cost $14k to repair. Contaminated coolant in Mercedes-Benz GLC 300 models often results from the internal failure of a "desiccant bag" inside the coolant expansion tank, which disintegrates, releasing material that clogs the heater core. Symptoms include black residue in the tank, reduced cabin heat, and engine overheating. Key actions include replacing the expansion tank (reservoir) and flushing the entire system.
- Air bags · Seat belts
A message that passenger air bag is damaged/will not deploy appears. Passenger seat belt gets stuck and cannot be opened. Check engine light on-pvc valve issue most likely.
- Unknown or other
Sunroof exploded and shattered. I heard it while driving and held on tightly to the steering wheel before I realized what it was. the dealer and my auto insurance have been called, neither picked up, and I left each a voice mail message. no warning lamps, messages or other symptoms of the problem occurred.
- Unknown or other
My sunroof just exploded while driving on the highway without any impact or warning. It was a clear sunny day. There wasn't a vehicle in front of me. Nothing fell on my windshield nor sunroof. The sudden explosion and shattering of the glass was extremely startling. I had a mesh underneath…
My sunroof just exploded while driving on the highway without any impact or warning. It was a clear sunny day. There wasn't a vehicle in front of me. Nothing fell on my windshield nor sunroof. The sudden explosion and shattering of the glass was extremely startling. I had a mesh underneath the sunroof that contained some of the shattered glass so it did not fall on me while I was driving. I'm so thankful there wasn't a car behind me for the glass debris to fall on. Mercedes USA was not helpful, unresponsive for many weeks. They eventually declined repair coverage due to out of warranty, not manufacture defect nor safety issue.
- Vehicle speed control
I was driving on a street 5mph and all of a sudden my car surged and led me to curb where i knocked hit a steer din and it veered onto someone’s lawn and hit a huge planter and stopped . Air bags were deployed . I had no control over the car . EDR was preformed and I’m sure it was a throttle surge…
I was driving on a street 5mph and all of a sudden my car surged and led me to curb where i knocked hit a steer din and it veered onto someone’s lawn and hit a huge planter and stopped . Air bags were deployed . I had no control over the car . EDR was preformed and I’m sure it was a throttle surge issue and cause unintended acceleration . The edr shows I was going 5 miles an hour but then says pedal was pushed to 100%. While traveling at approximately 4–5 mph during a low-speed maneuver, with light accelerator input, the vehicle unexpectedly surged forward. I did not intend to accelerate. The vehicle rapidly increased speed, left the roadway, struck a street sign and a planter, and the airbags deployed. Event Data Recorder (EDR) data retrieved by the insurer (Mercury Insurance) shows the vehicle traveling at low speed immediately prior to the event, followed by a recorded 100% accelerator pedal position. This data does not reflect my driving intent and appears inconsistent with the low-speed conditions. The EDR documentation notes that accelerator pedal position is sampled asynchronously and reflects values transmitted to the SRS Control Module, not continuous pedal input or driver intent. No brake input was recorded prior to the impact. The sudden acceleration occurred too quickly to react. Mercedes-Benz inspected the vehicle and released only the EDR data, declining to provide further clarification regarding throttle control logic, pedal sensor correlation, or torque command behavior. I am reporting this incident due to concern that low-speed throttle control behavior, software logic, or transmission engagement may result in unintended acceleration without corresponding driver intent, posing a safety risk during parking-lot or low-speed driving conditions.
- Power train
The contact owns a 2019 Mercedes-Benz GLC300. The contact stated that while shifting from reverse to drive, the vehicle stalled and remained in neutral. After the vehicle stalled, the vehicle took approximately 8 minutes before the vehicle could be shifted into drive. Once in drive, the vehicle…
The contact owns a 2019 Mercedes-Benz GLC300. The contact stated that while shifting from reverse to drive, the vehicle stalled and remained in neutral. After the vehicle stalled, the vehicle took approximately 8 minutes before the vehicle could be shifted into drive. Once in drive, the vehicle would jerk and shift to D3 before accelerating. The check engine warning light would illuminate while in reverse. The vehicle was taken to the dealer, who diagnosed a transmission failure due to a malfunctioning valve body and low pump pressure. The dealer confirmed that the VIN was not under recall and that the issue was not covered under warranty. The vehicle was not repaired. The contact informed the manufacturer of the failure, and a case was opened. The manufacturer referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 60,000.
- Vehicle speed control
The contact owned a 2019 Mercedes-Benz GLC 300. The contact stated that while driving at 15 MPH up and down the street on the fourth trip, the vehicle pulled to the left and suddenly accelerated, traveled over the curb, went through a sign on a pole, vegetation, and crashed into a concrete planter…
The contact owned a 2019 Mercedes-Benz GLC 300. The contact stated that while driving at 15 MPH up and down the street on the fourth trip, the vehicle pulled to the left and suddenly accelerated, traveled over the curb, went through a sign on a pole, vegetation, and crashed into a concrete planter box. There were no warning lights illuminated. The air bag deployed. The contact sustained bruises on her knees and hands. Medical attention was provided at the hospital. The paramedics, the police department, and the fire department were on the scene. The paramedics checked her out at the scene. There were no reported fires. A police report was filed. The vehicle was towed to a tow lot. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The contact was working with her insurance company to obtain the black box. The vehicle was deemed a total loss by the insurance company. The manufacturer was not contacted. The failure mileage was 48,000.
- Structure
The contact owns a 2019 Mercedes-Benz GLC 300. The contact stated that while driving 60 MPH, there was an abnormal cracking sound coming from the roof. The contact stated that upon arriving to the destination and parking the vehicle, the contact became aware that the panoramic roof panel had…
The contact owns a 2019 Mercedes-Benz GLC 300. The contact stated that while driving 60 MPH, there was an abnormal cracking sound coming from the roof. The contact stated that upon arriving to the destination and parking the vehicle, the contact became aware that the panoramic roof panel had detached. The dealer was notified of the failure. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Numbers: 23V854000 (Structure) and 21V197000 (Structure). The manufacturer was notified of the failure and informed the contact that the VIN was not included in the recalls, and assistance could not be provided because the vehicle was out of warranty. The failure mileage was approximately 30,000.
- Power train
The contact owns a 2019 Mercedes-Benz GLC300. The contact stated that while stopped at a stoplight on a hill, the vehicle rolled backwards. The contact stated that the brake pedal was depressed to stop the vehicle from rolling backwards, preventing the vehicle from hitting the vehicle behind. The…
The contact owns a 2019 Mercedes-Benz GLC300. The contact stated that while stopped at a stoplight on a hill, the vehicle rolled backwards. The contact stated that the brake pedal was depressed to stop the vehicle from rolling backwards, preventing the vehicle from hitting the vehicle behind. The contact stated that the failure had occurred several times. The vehicle was taken to the dealer; however, the failure was not duplicated. The contact was informed that rolling backwards was normal. The manufacturer was not made aware of the failure. The failure mileage was approximately 63,500.
- Visibility › Sun/moon roof assembly
While driving on Route 95 the Front Stationary Sunroof Panel separated and flew off
- Electrical system · Engine
FIRE! NHTSA Vehicle Safety Complaint – Mercedes-Benz GLC300 Complainant Information: [XXX] [XXX] Phone: [XXX] Email: [XXX] Vehicle Information: 2019 Mercedes-Benz GLC300 4MATIC VIN: [XXX] Purchase Location: Missouri Incident Location: St. Louis, MO Date of Incident: [XXX] Date of Report…
FIRE! NHTSA Vehicle Safety Complaint – Mercedes-Benz GLC300 Complainant Information: [XXX] [XXX] Phone: [XXX] Email: [XXX] Vehicle Information: 2019 Mercedes-Benz GLC300 4MATIC VIN: [XXX] Purchase Location: Missouri Incident Location: St. Louis, MO Date of Incident: [XXX] Date of Report Submission: July 12, 2025 Summary of Incident: On [XXX] , my 2019 Mercedes-Benz GLC300 4MATIC spontaneously caught fire while parked. I immediately contacted Mercedes-Benz Roadside Assistance, and the vehicle was towed for inspection. Mercedes-Benz later claimed the fire originated in the engine compartment, yet took no accountability and cited “missing components” as an excuse to avoid liability. Photographic evidence shows that the parts were present immediately after the fire. Mercedes-Benz denied that NHTSA Recall 21V961000 applied to this vehicle, despite clear similarity in symptoms (fire risk due to fuel or electrical issues). I was also never notified of any fire risk. Furthermore, towing coordination failures led to my vehicle being sent to a third-party lot, incurring unauthorized fees. Safety Concern: The spontaneous combustion of this vehicle presents a serious public safety risk. I am concerned this issue may be more widespread and underreported. Mercedes-Benz’s failure to take accountability and deflecting blame could endanger other consumers. Desired Action: 1. Federal investigation into similar fire-related complaints involving 2019 GLC300s. 2. Reconsideration of eligibility under Recall 21V961000 or related campaigns. 3. Consumer safety alert or expanded recall if defect patterns are confirmed. Attachments Provided: - Mercedes-Benz USA denial letter dated July 11, 2025 - Photos of the fire damage - Letters and written communications Signature: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Electrical system · Engine
- My transmission is malfunctioning. It is available for inspection. - My car is not allowing me to shift from reverse to drive. When I try to put it in drive, it gets stuck in neutral. My safety is at risk as I was trying to do a quick 3-point turn and got stuck in the lane. - Yes, the problem…
- My transmission is malfunctioning. It is available for inspection. - My car is not allowing me to shift from reverse to drive. When I try to put it in drive, it gets stuck in neutral. My safety is at risk as I was trying to do a quick 3-point turn and got stuck in the lane. - Yes, the problem has been confirmed by an independent service center. There was a recall by Mercedes Benz for the same issue in 2020, but for some reason my car isn't included. - The vehicle has been inspected by an independent service center - No warning lamps or messaged prior to the failure which first appeared on Thursday, June 5.
- Electrical system · Fuel/propulsion system · Structure › Body
On May 22, 2025, while parked, my 2019 Mercedes-Benz GLC300 spontaneously caught fire, completely destroying the vehicle. Thankfully, no one was inside, and no injuries occurred, but the property damage was significant. I later discovered Recall 21V961000 / Campaign 2022030003 affecting some 2019…
On May 22, 2025, while parked, my 2019 Mercedes-Benz GLC300 spontaneously caught fire, completely destroying the vehicle. Thankfully, no one was inside, and no injuries occurred, but the property damage was significant. I later discovered Recall 21V961000 / Campaign 2022030003 affecting some 2019 GLC300s for fuel leaks at the fuel rail/injector interface, which pose a serious fire hazard. Further research has shown reports of loose ground connections in these vehicles as well, increasing the risk of sparks igniting leaked fuel. Given that my vehicle caught fire spontaneously and matches the defect described in this recall, I firmly believe this incident was related to that defect. Mercedes-Benz has not provided adequate assistance. The vehicle was towed to a local dealership (Plaza Mercedes-Benz), but they refused to accept it, adding further confusion and hardship. I am submitting this report to request that NHTSA fully investigate this issue and work to ensure that Mercedes-Benz USA takes responsibility for this vehicle defect and compensates me for this dangerous failure. I am happy to provide photos, tow reports, or further documentation if needed. Thank you for your assistance in ensuring public safety.
- Engine
Faulty Positive Crankcase Ventilation Valve. Seems a very common failure which causes poor emissions and potentially further engine damage.
- Power train
The component that failed was the right front differential. My safety and the safety of others was put at high risk as I was driving at 60 mph on the highway and my vehicle suddenly and abruptly reduced speed to about 15mph without any warning. This created an extremely dangerous and potentially…
The component that failed was the right front differential. My safety and the safety of others was put at high risk as I was driving at 60 mph on the highway and my vehicle suddenly and abruptly reduced speed to about 15mph without any warning. This created an extremely dangerous and potentially hazardous situation as I tried to maneuver my car at this very low speed on the highway in the middle lane safely to the side of the highway. Cars around me quickly maneuvered around me in attempts to avoid my slow moving vehicle and not hit me. The entire experience was terrifying, especially given that the car gave no prior indication of a malfunction. The vehicle had to be towed to Mercedes. I have no real answers from Mercedes as to the cause or why the vehicle did not notify me or why the service light did not go on. The vehicle only had 51,000 miles and is well taken care of. Because the car was out of warranty they refused to cover the expense. I called and sent letters to corporate and received $2500 towards a $6000 bill. I feel this was a safety issue and my car shut down without any type of warning and Mercedes should cover all repair costs. The car has been repaired, but I am still nervous to drive it.
- Unknown or other
Sunroof exploded while I was driving. No other cars around me, pretty day, not a very hot day. I’m driving along and suddenly hear a loud POP that sounded like a shotgun going off! I swerved, but thankfully did not leave the road. Shattered glass was contained in the cover of the sunroof as I…
Sunroof exploded while I was driving. No other cars around me, pretty day, not a very hot day. I’m driving along and suddenly hear a loud POP that sounded like a shotgun going off! I swerved, but thankfully did not leave the road. Shattered glass was contained in the cover of the sunroof as I didn’t have it open at the time. A huge hole is in my roof of my car! I called the dealership who said it was not covered under any warranty although I just got the vehicle in Feb of this year. He said I would have to contact corporate. I contacted corporate who said bring it in for an inspection. At the conclusion of the inspection on 10/8/24, they could not determine if it was a manufacturer defect or outside sources since they could not find a point of impact, because the glass was nearly all gone. I had to get my insurance involved. There was no warning whatsoever. The dealership said no recalls. It just exploded all of a sudden!
- Wheels › Hub
The contact owns a 2019 Mercedes-Benz GLC300. The contact stated that the tires were worn in one specific area and the failure had also occurred after replacing the tires. The contact took the vehicle to the dealer where an alignment was completed; however, it was confirmed that the rear hub…
The contact owns a 2019 Mercedes-Benz GLC300. The contact stated that the tires were worn in one specific area and the failure had also occurred after replacing the tires. The contact took the vehicle to the dealer where an alignment was completed; however, it was confirmed that the rear hub bearing was rubbing the tires and needed to be replaced. The vehicle had not been repaired. The manufacturer was not made aware of the failure. The failure mileage was 79,000.
- Structure
The contact owns a 2019 Mercedes-Benz GLC300. The contact stated while driving at an undisclosed speed, the contact heard an abnormal sound emanating from the vehicle from an unknown location. The contact pulled over to the shoulder of the roadway and after a visual inspection of the exterior of…
The contact owns a 2019 Mercedes-Benz GLC300. The contact stated while driving at an undisclosed speed, the contact heard an abnormal sound emanating from the vehicle from an unknown location. The contact pulled over to the shoulder of the roadway and after a visual inspection of the exterior of the vehicle, the contact observed that the front roof panel had become detached. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 23V854000 (Structure) but the VIN was not included. The manufacturer was notified of the failure but referred the contact to the NHTSA Hotline for assistance. The failure mileage was unknown.
- Engine · Fuel/propulsion system · Unknown or other
The error code is P052E and it is a PCV Code Crankcase Ventilation Oil Separator. It's a time-consuming and expensive repair that seems to be regularly occurring on a lot Mercedes Benz that have this installed. And it happens often on cars with under 50K miles on them and when it's just been out…
The error code is P052E and it is a PCV Code Crankcase Ventilation Oil Separator. It's a time-consuming and expensive repair that seems to be regularly occurring on a lot Mercedes Benz that have this installed. And it happens often on cars with under 50K miles on them and when it's just been out of warranty this is a small inexpensive part that the customer funds through the cost of labor. Not that mechanics don't deserve their labor costs, but Mercedes ought to fix this is issue as it is borne by the consumer of a high end vehicle for a consistent, faulty part that they have engineered.
- Tires
The four tires were replaced on [XXX] at 28,000 miles. Then 4 additional tires replaced at 57,000 miles [XXX]. Less than one year in Oct of 2023 I noticed a sound coming from the front tires when driving . Two of the front tires needed to be replaced 75300 miles . These tires FPIRREILLI…
The four tires were replaced on [XXX] at 28,000 miles. Then 4 additional tires replaced at 57,000 miles [XXX]. Less than one year in Oct of 2023 I noticed a sound coming from the front tires when driving . Two of the front tires needed to be replaced 75300 miles . These tires FPIRREILLI SCROPION VERDE 235/55 R19 101H are having to be replaced too often . There appears to be a defect in the tires INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Visibility › Power window devices and controls
The contact owns a 2019 Mercedes-Benz GLC300. The contact stated while driving 25-30 MPH in the rain, the front driver's side window became foggy, and the front driver's side window power switch button was depressed to roll down the window to clear the fog; however, the switch fractured in her…
The contact owns a 2019 Mercedes-Benz GLC300. The contact stated while driving 25-30 MPH in the rain, the front driver's side window became foggy, and the front driver's side window power switch button was depressed to roll down the window to clear the fog; however, the switch fractured in her hand. The manufacturer was notified of the failure and a case was opened. The manufacturer referred the contact to the dealer for assistance. The dealer was contacted. The vehicle was not diagnosed or repaired. The manufacturer later informed the contact that they could not help. The failure mileage was approximately 27,500.
- Engine
P052E71 Engine Separator and actuator malfunctioning. Was told this fails several times on Mercedes vehicles. I will not pass emissions with this issue. Over $2K to repair and engine light along with code appears. I have videos of the engine light coming off and on. Car has been inspected by Firestone and Mercedes Service Center.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Front Roof Panel Detachment
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class…
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010644Complaint Paint damage on door paneling in area of door handle (see picture 1). Cause Possible tolerance complaint regarding the door handle Remedy 1. Paint the affected area of the door paneling using the spot repair procedure in accordance with the manufacturer's specifications. 2. Replace door handle, ensuring that the door handle bearing bracket is installed correctly (see picture 2). Note: The optimized door handles are marked as shown in the illustration (see picture 3).
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008056Complaint Check engine light on. Fault code P207273 - "Throttle actuator valve is blocked due to ice" stored. Engine may crank and not start. Fault code P210185 may also be stored. Cause Moisture freezing on throttle actuator during extreme low ambient temperatures. Remedy Update software of engine control module. Software increases throttle valve flapping after engine turned off to prevent moisture buildup.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005314Complaint Yellow Coolant warning comes on in cluster Fault codes below are current or stored in MED41 P0A0500- The actuation of the circulation pump for the low-temperature circuit has an open circuit. P00B700- The coolant flow is too low. P0C7300- Circulation pump 1 for the low-temperature circuit has a malfunction. Cause Air may be trapped in the coolant circuit for transmission cooler Remedy Check coolant level. -If coolant level is low, locate source of leak and correct. -If coolant level is ok, perform procedure in attached instructions to bleed the coolant circuit to transmission cooler. 1. Allow cooling system to cool to ambient temperature. 2. Fill coolant reservoir completely. 3. Slightly open coolant connection shown in attachment (red arrow) to allow air to escape. 4. Once coolant flows out, close connection and correct coolant level. 5. Clear fault codes and check for further symptoms.
- 11005313Complaint Check engine light on and fault code P019185 current or stored in MED41 control unit. Adaptation and misfire faults may also be stored. Vehicle may enter limp home mode. Cause False detection of rail pressure sensor out of range. Remedy Update software of engine control module N3/10. Reset mixture adaptation and clear fault codes.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11005276Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2018 C300 | Model year 2016-2018 GLC300 and E300 | ALL model year SLK/SLC300 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2018 C300 and 2016-2018 GLC300 and E300 vehicles. Model year 2015-2017 C300 | Model year 2019 GLC300 and E300 Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required.
- 11000623Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2015-2018 (non-hybrid), and ALL model year 172 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for hybrid and model year 2015-2018 vehicles. Model year 2019 (Except model 172 and hybrid variants) Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 11000598Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case.
- 10253722Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Model year 2015-2018 Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2015-2018 vehicles. Model year 2019 Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 10253703This is to notify you of the Service Campaign OTA update for the MBUX system software in 750,313 Model Year (MY) MY19-24 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10252835Always use the latest XENTRY Diagnosis software release with all available add-ons. Make sure to follow the operation steps exactly as described in XENTRY Diagnosis. Use a battery charger to ensure sufficient power supply of the vehicle on-board electrical system battery (greater than 12.5 V). If XENTRY Diagnosis is already connected to the vehicle, start with operation step 2. If two or more software updates or SCN codings are performed during one workshop visit, operation items 02-4762 and 02-5058 may be invoiced only once for each workshop order. Work procedure 1. Connect XENTRY Diagnosis. 2. Update N129/1 - power electronics (SG-EM) control unit software. To do this, select menu item "Quick test view N129/1 - power electronics (SG-EM) Adaptations Control unit update Update of control unit software". Then follow the user guidance in XENTRY Diagnosis. 3. Disconnect XENTRY Diagnosis.
- 10251356The radio station favorites list is no longer present after bus idle Saving process during download Perform software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00).
- 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
- 10249543In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage for the pressure sensor in certain Model Year (MY) hybrid vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles, whichever occurs first, due to the following issue: The pressure sensor installed on the fuel tank or on the fuel filler neck might detect an electrical error as a result of contaminated fuel, which could cause the check engine malfunction indicator lamp (MIL) to illuminate. Please note, the error can only occur either on the tank or on the filler neck pressure sensor. It cannot occur simultaneously on both sensors. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P1B9D28 Pressure Sensor on filler pipe. P045128 Pressure Sensor Tank. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 47147 Pressure Sensor, Fuel Tank Part(s): A 000 905 59 04 Pressure Sensor (To tank) or- A 000 905 89 16 Pressure Sensor (Filler neck) Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty.
- 10249540Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2019-2023 A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.
- 10249495Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!
- 10249482The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.
- 10248203Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service for the navigation system. Additional product improvements including infotainment system robustness will be implemented. The software update will be downloaded in the background. The subsequent installation takes roughly 45 minutes and requires the customer's consent in the vehicle. During installation, the system can be used without restriction. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10248195Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10243565In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the intake line assembly on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2015 - 2020 C/E/GLC/SLC and SLK vehicles, under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended, resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valve might also increase exhaust gas emission. . Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
- 10243308Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. Do not perform software update of N3/10 Engine control unit at this time. This LI will be updated once the software solution is available. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10241531In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the intake line assembly in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: Under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended,resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valvemight also increase exhaust gas emission. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has amalfunction. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 0101D Solenoid valve, crankcase ventilation system Part(s): A 274 090 5600 80 Intake Line Assembly (inclusive of oil separator, partial load ventilation valve and full-load ventilationvalve.) Where applicable, an ECU software update will be provided for certain vehicle variants. Time Allowed: Intake Line Assembly : 5 hours 40 minutes Software Update: 1 hour Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty.
- 10241527Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customers vehicle. The OTA may be validated as successful on the customers Mercedes Me connect app under Over-the-Air Vehicle Updates as Update for the communication module. If the OTA is successful it will show a green installed and date of installation in the Over-the-Air update section.
Every Mercedes-Benz GLC 300 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.