2016 Mercedes-Benz GLE350
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › GLE350 › 2016
These records cover every 2016 Mercedes-Benz GLE350. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
9 recalls name the 2016 Mercedes-Benz GLE350. Newest first.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML550, 2012-2015 ML350, AMG ML63, 2015 ML250, ML400, 2016 GLE450, GLE300, 2016-2018 GLE350, GLE550, 2016-2019 GLE400, 2017-2019 AMG GLE43, and 2016-2020 AMG GLE63 vehicles. Water might accumulate in the spare tire wheel well and damage the fuel pump control unit, which could cause an engine…
Risk and remedy
Risk
An engine stall while driving increases the risk of a crash.
Remedy
Dealers will install a water drain plug, inspect for water intrusion, and replace the fuel pump control unit as necessary, free of charge. Owner notification letters were mailed February 15, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers for this recall are 2023010002 and 2023010003.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML350 Bluetec 4Matic and ML550 4Matic, 2012-2015 ML63 AMG 4Matic and ML350 4Matic, 2013-2016 GL350 Bluetec 4Matic, GL550 4Matic and GL63 AMG 4Matic, 2017 GLS350d 4Matic, GLS450 4Matic, GLS550 4Matic and GLS63 AMG 4Matic, 2015 ML400 4Matic, 2016 GLE400 4Matic, GLE350 4Matic, GLE63 AMG 4Matic…
Risk and remedy
Risk
The leaking oil in the presence of an ignition source can increase the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will correct the oil level as necessary and replace the reservoir sealing cap to prevent oil foam from leaking out, free of charge. The recall began August 30, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018070015.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 GLE300d 4Matic, GLE400 4Matic, GLE350 4Matic, GLE63 AMG, GLE63 AMG Coupe, GLE63S AMG and GLE63S AMG Coupe, and 2017 GLS450 4Matic, GLE550 4Matic, and GLE63 AMG 4Matic vehicles. These vehicles may have excess bulkhead insulation extending into the lower windshield area, possibly affecting the…
Risk and remedy
Risk
If the passenger's frontal air bag does not function as designed in the event of a crash, the front seat passenger has an increased risk of injury.
Remedy
MBUSA will notify owners, and dealers will remove any excess bulkhead insulation and rework the windshield bonding, as necessary, free of charge. Interim owner letters will be mailed in December 2017. Owners will receive a second notice when the remedy is available in late January 2018. MBUSA's number for this recall is 2018020002. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2016 GLE300d 4Matic, E400 4Matic Coupe, GL63 AMG, GLE350, GLE350 4Matic, GLE350d 4Matic, GLE400 4Matic, GLE43 AMG Coupe 4Matic, GLE550e 4Matic, GLE63 AMG 4Matic, GLE63S AMG 4Matic and GLE63S AMG Coupe 4Matic vehicles, 2017 E300 4Matic and GLS63 AMG 4Matic vehicles, and 2016-2017 GL350 4Matic BlueTec…
Risk and remedy
Risk
If water enters the power steering control unit, the power steering assist may be deactivated, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the connector and inspect the electric power steering rack, replacing the rack as necessary. These repairs will be performed free of charge. Remedy parts are currently unavailable. Interim notices informing owners of the safety risk are expected to be mailed June 30, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 GLE350 4Matic and GLS 450 4Matic vehicles. The windshield bonding may be insufficient and, as a result, the windshield may separate from the vehicle in a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash…
Risk and remedy
Risk
If the windshield detaches in the event of a crash, the passenger frontal air bag may not be supported properly after it deploys, increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will replace the windshield, free of charge. The recall began March 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 GLE350 4Matic, GLE350, GLE350 4Matic Bluetec, GL450 4Matic, and GLE450 Coupe 4Matic vehicles. In the affected vehicles, the bolt that connects the upper control arm and the axle stub may not have been properly tightened.
Risk and remedy
Risk
The loose bolt may cause improper wheel tracking, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect the tightness of the bolt connecting the upper control arm and the axle stub on the affected vehicles, replacing the upper control arm if necessary, free of charge. The recall began March 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016-2017 GL350 4Matic Bluetec, GL550 4Matic, GLE350 4Matic, GLE43 AMG Coupe, GLE450 4Matic, 2016 GLE300d 4Matic, GLE350, GLE350d 4Matic, GLE400 4Matic, GLE550e 4Matic, GLE63 AMG, GLE63 AMG 4Matic, GLE63S AMG 4Matic Coupe, and 2017 GLS63 AMG vehicles manufactured April 23, 2014, to May 10, 2016.…
Risk and remedy
Risk
If the front passenger air bag does not deploy as necessary in the event of a crash, the front passenger has an increased risk of injury.
Remedy
MBUSA will notify owners, and dealers will update the OCS software, free of charge. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016-2017 GLE 300d 4MATIC, GLE 350, GLE 350 4MATIC, and GLE 400 4MATIC vehicles manufactured October 14, 2015, to November 23, 2015. The low beam headlights on the affected vehicles may not be properly adjusted. As such, these vehicles fail to comply with the requirements of Federal Motor…
Risk and remedy
Risk
If the low-beam headlights are out of adjustment, the driver's visibility may be reduced, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect and correct the headlight adjustment, as necessary, free of charge. The recall is expected to begin in November 2016. Owners may contact MBUSA customer service at 1-800-367-6372.
Owner complaints
53 complaints4 involved a crash4 involved a fire3 injuries
What owners report most
Latest complaints
- Electrical system · Service brakes · Vehicle speed control
On 8/28/2026, my Mercedes-Benz GLE 350 (W166, M276 engine) experienced a sudden, catastrophic engine stall while driving in active traffic. There was no Check Engine Light (CEL), dashboard warning, or mechanical hesitation prior to the failure. The vehicle instantly lost all propulsion, power…
On 8/28/2026, my Mercedes-Benz GLE 350 (W166, M276 engine) experienced a sudden, catastrophic engine stall while driving in active traffic. There was no Check Engine Light (CEL), dashboard warning, or mechanical hesitation prior to the failure. The vehicle instantly lost all propulsion, power steering, and power braking assist, creating an extreme crash hazard and requiring immense physical effort to maneuver the dead vehicle off the roadway. Independent diagnostic teardown by a module specialist confirmed the root cause: an unrepairable internal short circuit between the internal PCB layers of the Engine Control Unit (ECU). Because Mercedes-Benz chose to mount this sensitive electronic module directly to the top of the hot engine block, it is subjected to extreme thermal cycling and vibration. This predictable thermal degradation causes the internal board layers to delaminate and short out. When this internal short occurs, the ECU instantly dies and shuts down the entire vehicle without warning. This is a severe, life-threatening engineering defect. A safety investigation is urgently needed to address the mounting location and thermal failure rate of M276 ECUs before a sudden high-speed stall results in a fatal collision.
- Electrical system · Service brakes · Vehicle speed control
On 8/28/2026, my Mercedes-Benz GLE 350 (W166, M276 engine) experienced a sudden, catastrophic engine stall while driving in active traffic. There was no Check Engine Light (CEL), dashboard warning, or mechanical hesitation prior to the failure. The vehicle instantly lost all propulsion, power…
On 8/28/2026, my Mercedes-Benz GLE 350 (W166, M276 engine) experienced a sudden, catastrophic engine stall while driving in active traffic. There was no Check Engine Light (CEL), dashboard warning, or mechanical hesitation prior to the failure. The vehicle instantly lost all propulsion, power steering, and power braking assist, creating an extreme crash hazard and requiring immense physical effort to maneuver the dead vehicle off the roadway. Independent diagnostic teardown by a module specialist confirmed the root cause: an unrepairable internal short circuit between the internal PCB layers of the Engine Control Unit (ECU). Because Mercedes-Benz chose to mount this sensitive electronic module directly to the top of the hot engine block, it is subjected to extreme thermal cycling and vibration. This predictable thermal degradation causes the internal board layers to delaminate and short out. When this internal short occurs, the ECU instantly dies and shuts down the entire vehicle without warning. This is a severe, life-threatening engineering defect. A safety investigation is urgently needed to address the mounting location and thermal failure rate of M276 ECUs before a sudden high-speed stall results in a fatal collision.
- Electrical system · Fuel/propulsion system · Steering
While driving my 2016 Mercedes-Benz GLE 350, the vehicle suddenly shut off and lost propulsion without warning. There was no check-engine light or other warning before the failure. The engine would crank afterward but would not restart, leaving the vehicle disabled. The vehicle has an open NHTSA…
While driving my 2016 Mercedes-Benz GLE 350, the vehicle suddenly shut off and lost propulsion without warning. There was no check-engine light or other warning before the failure. The engine would crank afterward but would not restart, leaving the vehicle disabled. The vehicle has an open NHTSA safety recall (22V-955) involving the fuel pump control unit and potential loss of propulsion. The vehicle is currently at Benzel-Busch Mercedes-Benz for recall inspection and diagnosis. I am reporting this because the sudden loss of propulsion while driving created a serious safety risk.
- Power train
At 72,000 miles the rear differential failed. Repair required else car could abruptly stop rolling, become uncontrollable and cause a serious wreck. The part is over $5,000
- Engine and engine cooling · Fuel system, gasoline
The contact owns a 2016 Mercedes-Benz GLE350. The contact stated that while opening the door, a cracked fuel injector was spraying gasoline. When the door handle was pulled, an aftermarket module ignited the fuel, causing an explosion and heavy smoke from the engine compartment. The contact stated…
The contact owns a 2016 Mercedes-Benz GLE350. The contact stated that while opening the door, a cracked fuel injector was spraying gasoline. When the door handle was pulled, an aftermarket module ignited the fuel, causing an explosion and heavy smoke from the engine compartment. The contact stated that the vehicle had been taken to the dealer previously for the same issue, but the dealer dismissed the information and returned the vehicle. Shortly afterwards, the failure reoccurred and was recorded. The vehicle had been at the dealer for two months, and the dealer blamed the failure on an aftermarket part, even though the dealer had installed the parts. The vehicle was driven to the dealer, where it was diagnosed with fuel injector failure and was associated with the aftermarket parts that were installed by the dealer. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 133,000.
- Service brakes · Vehicle speed control
While waiting for traffic signal to change with foot on break pedal, the suv accelerated suddenly and lurched forward and rear ended the car ahead of me! Luckily, it was a Hummer with a tire mounted on the rear door and damage occurred only to my MB. Front end has severe damage, hood buckled and…
While waiting for traffic signal to change with foot on break pedal, the suv accelerated suddenly and lurched forward and rear ended the car ahead of me! Luckily, it was a Hummer with a tire mounted on the rear door and damage occurred only to my MB. Front end has severe damage, hood buckled and headlight broken! It was a spooky experience! 'chk breakpad wear' warning light has been coming on lately when starting and I was planning to get breaks chkd. But this was a frightening experience! Is there an issue with MB ECU like this? I'm in the process of filing insurance claim.
- Steering
The contact owns a 2016 Mercedes-Benz GLE350. The contact stated that while driving at various speeds, an abnormal sound was coming from the steering box. No warning light was illuminated. The local dealer was not contacted. The vehicle was not diagnosed or repaired. In addition, the contact…
The contact owns a 2016 Mercedes-Benz GLE350. The contact stated that while driving at various speeds, an abnormal sound was coming from the steering box. No warning light was illuminated. The local dealer was not contacted. The vehicle was not diagnosed or repaired. In addition, the contact related the failure to NHTSA Campaign Number: 17V241000 (Steering); however, the VIN was not included. The manufacturer was made aware of the failure. The failure mileage was approximately 70,000.
- Fuel/propulsion system
This has previously been reported, but NHTSA email indicated I needed to file formal complaint. Fuel injector(s) leaked while vehicle parked overnight in driveway. ECU detected fuel and subsequent ignition/spark caused "explosion' blowing out engine intake manifold (appx 50-75 pieces found).…
This has previously been reported, but NHTSA email indicated I needed to file formal complaint. Fuel injector(s) leaked while vehicle parked overnight in driveway. ECU detected fuel and subsequent ignition/spark caused "explosion' blowing out engine intake manifold (appx 50-75 pieces found). All 6 injectors and intake manifold required replacement. Mercedes Benz does have recall notification for failed/leaking fuel injectors, which includes both my model, and model year- but has claimed my VIN is not covered. MB recall campaign # 2022030003, dated 04/22/2022. I have retained engine intake manifold (main piece) for inspection. Fuel injectors were returned to MB. Safety risk is relatively obvious due to "explosion" and potential fire. Independent service agency (German Motors, Lakewood, CO- in business for over 25 years as MB only repair agency) diagnosed and performed repairs. Further, they informed me that in the investigation, they an other independent repair agencies/shops have in fact seen this before. No warnings, lights, or other symptoms were evident prior to injectors leaking.
- Fuel/propulsion system
Vehicle sitting in driveway. Fuel injector leakage and resultant engine control unit detecting fuel set off spark which resulted in explosion under hood. Completely destroyed engine intake manifold (over 100 pieces found), and requires all (6) new fuel injectors. Due to core return value, I…
Vehicle sitting in driveway. Fuel injector leakage and resultant engine control unit detecting fuel set off spark which resulted in explosion under hood. Completely destroyed engine intake manifold (over 100 pieces found), and requires all (6) new fuel injectors. Due to core return value, I will NOT be keeping injectors, but they have been inspected by certified mechanic where repairs are being done. Safety/risk is obvious- fire danger, explosion danger, etc. Vehicle was towed to German Motors, Lakewood CO. for repair. No warning indicators, no lights. Mechanics did inform me that this issue has been seen on other vehicles. Network of MB mechanics have been aware. MB USA is also aware of fuel injector leakage issues, and have issued a Safety & Emissions Recall Campaign (# 2022030003, dated 8/22/2022) for this model year and vehicle model type (GLE). MB USA however asserts that my specific VIN is not included in recall- but offers no reason. Currently, due to MB inability to provide replacement parts (engine intake manifold unavailable until Sept. 2025!), vehicle is still in repair facility. Invoices and write up will be available after repairs completed (using reclaimed intake manifold along with new injectors).
- Fuel/propulsion system
car has caught on fire due to (as diagnosed by certified MB mechanic) leaking from fuel injector(s). Issue is known to many MB mechanics. Issue DOES have a recall for other (non GLE350) models in this same year (2016). Request recall issued! Request assistance with having MB warranty/repair problem
- Child seat
The contact owns a 2016 Mercedes GLE350 with a Nuna Car Seat installed, Model Name: Rava, Model Number: CS05107RFD, Manufactured Date: May 05, 2021. The contact stated that on several occasions whenever the harness was tugged on, the harness failed to restrain the child seated in the child seat.…
The contact owns a 2016 Mercedes GLE350 with a Nuna Car Seat installed, Model Name: Rava, Model Number: CS05107RFD, Manufactured Date: May 05, 2021. The contact stated that on several occasions whenever the harness was tugged on, the harness failed to restrain the child seated in the child seat. The manufacturer was notified of the failure and advised the contact that the kits to clean the release button on the bottom of the car seat would be released soon. The car seat was not replaced.
- Engine and engine cooling › Exhaust system › Emission control › Catalytic convertor
The contact owns a 2016 Mercedes-Benz GLE350. The contact stated while driving at an undisclosed speed, the vehicle shuddered and hesitated while accelerating and depressing the accelerator pedal. The check engine warning light was illuminated. The vehicle was taken to a local dealer where it was…
The contact owns a 2016 Mercedes-Benz GLE350. The contact stated while driving at an undisclosed speed, the vehicle shuddered and hesitated while accelerating and depressing the accelerator pedal. The check engine warning light was illuminated. The vehicle was taken to a local dealer where it was scanned, and the dealer retrieved DTC code: P04200. The contact was informed that the passenger side catalytic converter had failed, causing the Oxygen sensor to run lean. The contact stated that upon further investigation, the failure was linked to Emission Service Campaign: 2022080005; however, the VIN was not included. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 90,000.
- Fuel/propulsion system
Car was running normally then check engine light illuminated and car shut off. Was able to coast to roadside. Car would not restart. Diagnosed by professional authorized Mercedes repair shop as fuel injector failure. No parts available after the repair for inspection. Because of shut off while…
Car was running normally then check engine light illuminated and car shut off. Was able to coast to roadside. Car would not restart. Diagnosed by professional authorized Mercedes repair shop as fuel injector failure. No parts available after the repair for inspection. Because of shut off while being driven in busy traffic, I was at serious risk of a different vehicle hitting my vehicle. Also emergency brake would not disengage since car would not start so could not be pushed further off the road.
- Engine
Reporting an issue with 2016 GLE 350 4Matic - 78000 Mileage - Intake Air System Leak - Code P007900 Symptoms: High pitched Whistling noise coming from Engine Impact: Unsafe drivability; safely hazard Defective Part Replaced: Crank case Valve Assembly Customer Expectation: Due to the nature…
Reporting an issue with 2016 GLE 350 4Matic - 78000 Mileage - Intake Air System Leak - Code P007900 Symptoms: High pitched Whistling noise coming from Engine Impact: Unsafe drivability; safely hazard Defective Part Replaced: Crank case Valve Assembly Customer Expectation: Due to the nature, Mercedes, the car manufacturer should offer an Emission Extended Warranty on this part. The repair expense should be reimbursed by Mercedes, the car manufacturer due to the nature of this issue.
- Engine and engine cooling · Fuel system, gasoline · Fuel system, gasoline › Delivery › Fuel pump
See attached document for complaint
- Engine and engine cooling · Vehicle speed control
The contact owns a 2016 Mercedes-Benz GLE350. The contact stated that while driving at an undisclosed speed, the vehicle failed to accelerate as needed. The console had overheated. The engine and oil warning lights were illuminated. The vehicle was taken to a local dealer, where it was diagnosed…
The contact owns a 2016 Mercedes-Benz GLE350. The contact stated that while driving at an undisclosed speed, the vehicle failed to accelerate as needed. The console had overheated. The engine and oil warning lights were illuminated. The vehicle was taken to a local dealer, where it was diagnosed that cylinder numbers 1, 2, and 3 was misfiring. The vehicle was not repaired. The manufacturer was not contacted. The failure mileage was approximately 118,000.
- Electrical system · Fuel/propulsion system · Unknown or other
I own a 2016 Mercedes GLE350 that was repaired under a safety recall involving failure of a fuel pump due to water intrusion into the spare wheel well. Mercedes Benz "fixed" the car under the safety recall however, several months later, my vehicle experienced the same exact issue - water intrusion…
I own a 2016 Mercedes GLE350 that was repaired under a safety recall involving failure of a fuel pump due to water intrusion into the spare wheel well. Mercedes Benz "fixed" the car under the safety recall however, several months later, my vehicle experienced the same exact issue - water intrusion entered the rear wheel well causing the fuel system to fail. Mercedes Benz currently has my vehicle and cannot locate the water leak (they are saying it is in the hatch area of my car). They are currently trying to charge me $890 to find the leak. However, the original safety recall on this vehicle states, "the cause of the defect may vary due to a development deviation in combination with production tolerances and possible customer influences when loading and unloading items from the rear hatch. Each cause could lead to a different issue and water intrusion. Therefore, the tightness in the rear area might not meet specifications." I understand that my vehicle is not the first to experience this issue and I believe this is a defect with this make/model/year. I am hopeful this will be looked into further as I believe this issue goes past the recall. I should not be required to pay for this and my safety should not be compromised due to this.
- Fuel/propulsion system
Engine light on dashboard turned on in beginning of Feb 2024 … bought vehicle to dealer for assessment … was told right side catalytic converter has malfunctioned and will need to be replaced … vehicle has about 66,000 miles and it was a 2016 vehicle … apparently warrantly had expired in Nov 2023 ……
Engine light on dashboard turned on in beginning of Feb 2024 … bought vehicle to dealer for assessment … was told right side catalytic converter has malfunctioned and will need to be replaced … vehicle has about 66,000 miles and it was a 2016 vehicle … apparently warrantly had expired in Nov 2023 … this does not seem right. Also, there are no right side catalystic converter available nationwide (not from Mercedes Benz manufacturer or off market). Wonder if this is a widespread issue … would like advisement.
- Air bags · Air bags › Sensor › Occupant classification · Structure › Body
The door hinges are an issue with these cars many many people are expressing the same issues which is the door hinges fail and start popping and cracking. Mercedes isn’t issuing a recall or remedy for this. Also there’s an issue with the passenger airbag weight sensors going bad which is throwing…
The door hinges are an issue with these cars many many people are expressing the same issues which is the door hinges fail and start popping and cracking. Mercedes isn’t issuing a recall or remedy for this. Also there’s an issue with the passenger airbag weight sensors going bad which is throwing the airbag light off (which this is also happening in my car) the service center I talked to knew about this is agreed it a issue they see time and time again with these cars. Mercedes needs to make this right.
- Service brakes
When driving, the vehicle suddenly slows down and then the brakes stop working. Vehicle then slows down to a complete stop. Happens randomly. This put me and other drivers at risk as cars behind me would suddenly have to slow down or stop without warning and I would have to steer out of the road to…
When driving, the vehicle suddenly slows down and then the brakes stop working. Vehicle then slows down to a complete stop. Happens randomly. This put me and other drivers at risk as cars behind me would suddenly have to slow down or stop without warning and I would have to steer out of the road to avoid a collision as the car is slowing down. At the same time, a message would appear saying "Collision Prevention Assist Plus Inoperative." I took the vehicle to a mercedes-benz dealer and they confirmed that this problem is due to a fault in the ABS system.
- Electrical system · Engine · Unknown or other
We were driving in the street and just suddenly the front of the car was on fire. We stopped the car and we had almost no time to get out because the flames got very big in just minutes. Good thing the doors weren't locked because we safely got out of the car. This incident happened in rush hour…
We were driving in the street and just suddenly the front of the car was on fire. We stopped the car and we had almost no time to get out because the flames got very big in just minutes. Good thing the doors weren't locked because we safely got out of the car. This incident happened in rush hour and there were lots of cars around us. This put not just the passengers in our car but other people around us in danger. We contacted Mercedes-Benz but they declined out claim and refused to investigate into this issue. Please help us hold Mercedes-Benz accountable.
- Power train
The contact owns a 2016 Mercedes-Benz GLE350. The contact stated that while driving 45-50 MPH, the messages "Car Not in Park" and " Transmission Not in Park - Chance of Car Rolling" were displayed, and the vehicle independently shifted into park(P) and stopped. The contact moved the gear shifter to…
The contact owns a 2016 Mercedes-Benz GLE350. The contact stated that while driving 45-50 MPH, the messages "Car Not in Park" and " Transmission Not in Park - Chance of Car Rolling" were displayed, and the vehicle independently shifted into park(P) and stopped. The contact moved the gear shifter to park and restarted the vehicle. The contact was able to continue driving; however, the failure reoccurred several times while driving. The vehicle was taken to an independent mechanic, where an unknown sensor was replaced; however, the failure recurred. The vehicle was taken to the dealer, where the repair was completed again, however, the failure persisted. The vehicle remained at the dealer. The contact stated that the failure had occurred 16 times within 6 years. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that they could not assist unless the vehicle was successfully diagnosed. The failure mileage was approximately 25,000.
- Power train
Vehicle became disabled while owner was driving. Car stopped accelerating and stalled in the roadway. Vehicle was inoperable and had to be towed to the dealership. According to the Mercedes Service technician the rear output shaft bearing went out, tore the splines off of the trans output shaft yolk and 7 bolts then broke off in the case for the intermediate plate. Thus requiring a new transmission.
- Fuel system, diesel · Fuel system, gasoline · Structure
The contact owns a 2016 Mercedes-Benz GLE350. The contact stated while driving approximately 30 MPH, the vehicle stalled and lost motive power. The vehicle failed to restart. No warning lights were illuminated. The vehicle was towed to the residence. The contact stated that the vehicle was then…
The contact owns a 2016 Mercedes-Benz GLE350. The contact stated while driving approximately 30 MPH, the vehicle stalled and lost motive power. The vehicle failed to restart. No warning lights were illuminated. The vehicle was towed to the residence. The contact stated that the vehicle was then towed to a local dealer, where it was diagnosed that an unknown module needed to be replaced; however, no repair was completed. The vehicle was then taken to an independent mechanic, where an unknown module was replaced. The vehicle was repaired; however, the failure reoccurred. Additionally, the contact stated that after a rainstorm there was water in the spare tire wheel well. The vehicle was taken back to the independent mechanic, where unknown repairs were completed. The contact had received notification of NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline). The manufacturer was not made aware of the failure. The failure mileage was 59,831.
- Engine · Fuel system, diesel · Fuel system, gasoline
The contact owns a 2016 Mercedes-Benz GLE350. The contact received notification of NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline). The contact stated a week later the vehicle began to hesitate and the check engine warning light was illuminated. The vehicle was not…
The contact owns a 2016 Mercedes-Benz GLE350. The contact received notification of NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline). The contact stated a week later the vehicle began to hesitate and the check engine warning light was illuminated. The vehicle was not drivable. The contact towed the vehicle to the local dealer, where it was diagnosed with needing the coil pack to be replaced. The contact was informed that the failure was not associated with the recall. The vehicle was not repaired. The manufacturer had not been informed of the failure. The failure mileage was approximately 43,000.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010750Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to FIN vehicle identification end number. If vehicle falls outside of FIN range, create a TIPS case. Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008070Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to VIN vehicle identification end number. If vehicle falls outside of VIN range, create a TIPS case. Model series 192: xxx xxx xx 182881 Model series 232: xxx xxx xx 182883 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
- 10205835Model series 167 noise on B/C/D pillars.
- 10205819Important new emission service campaign information.
- 10205814Fuel filler flap opens slowly/switch flashes/tank is bleeding instrument cluster warning
- 10205251Engine fan runs continuously, a/c inoperable or, engine light illuminates sporadically.
- 10205250Engine fan runs continuously, a/c inoperable or, engine light illuminates sporadically.
- 10205248"SOS mbrace service not activated".
- 10205247Traffic information service and posibly the voice control, nonfunctional after navigation software update.
- 10205147Ticking or pulsing noise from high-pressure pump and/or fuel injectors.
- 10202531Touch pad: Search lighting does not dim or does not turn on.
- 10199774Launch NCU 2021070020- Perform SCN coding in powertrain control unit
- 10195220For plug in hybrid and electric variants: Complaints about the electric range
- 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
- 10186145Creaking noise from fixed glass section of panoramic roof in area of rear passenger compartment grab handles
- 10184798Replace charge air hose between charge air cooler and turbocharger
- 10184797Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain Mercedes-Benz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or caused to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed.
- 10181195Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain MercedesBenz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or cause to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed. An authorized Mercedes-Benz dealer will install the AEM at a later date at no cost to the Owner/Lessee.
- 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
- 10179904Implausible "service due" instrument cluster message, head unit pop-up, or Mmc message
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10172683Information Label on Tire Sealant
Every Mercedes-Benz GLE350 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.