2017 Mercedes-Benz GLE350
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › GLE350 › 2017
These records cover every 2017 Mercedes-Benz GLE350. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2017 Mercedes-Benz GLE350. Newest first.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML550, 2012-2015 ML350, AMG ML63, 2015 ML250, ML400, 2016 GLE450, GLE300, 2016-2018 GLE350, GLE550, 2016-2019 GLE400, 2017-2019 AMG GLE43, and 2016-2020 AMG GLE63 vehicles. Water might accumulate in the spare tire wheel well and damage the fuel pump control unit, which could cause an engine…
Risk and remedy
Risk
An engine stall while driving increases the risk of a crash.
Remedy
Dealers will install a water drain plug, inspect for water intrusion, and replace the fuel pump control unit as necessary, free of charge. Owner notification letters were mailed February 15, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers for this recall are 2023010002 and 2023010003.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2019 C300, E300, 2018-2020 CLA250, 2020 CLS450, AMG E53, AMG GT53, GLE450, 2018 AMG E63, AMG GTA, 2017-2020 GLA250, GLC300, 2019 GLC350, AMG GLC43, 2017-2018 GLE350, 2019 AMG GLC 43, GLC350, GLE400, 2017 GLS450, S550, C300 Cabrio, and 2018-2019 S560 vehicles. On June 18, 2021, an additional 9…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting emergency services through the call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the communication module and activate it, if necessary, free of charge. The recall began March 31, 2021. Letters for the owners of the 9 additional vehicles were mailed July 9, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021030005.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017 GLE400 4Matic, GLE350 4Matic, GLE350, GLE550e 4Matic, GLE43 AMG 4Matic, GLE63 AMG 4Matic, GLS450, GLE63S 4Matic, GLS63 4Matic, S550e, S600, S63 AMG 4Matic, S65 AMG, S550, Mercedes-Maybach S600, Mercedes-Maybach S550 4Matic, GLE43 AMG 4Matic Coupe, GLE63S 4Matic Coupe, 2017-2018 GLS550 4Matic, S550…
Risk and remedy
Risk
If the door appears to be locked, the door may be unintentionally opened, increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the left rear door lock, replacing it as necessary, free of charge. The recall is expected to begin in January 2018. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017 GLE 400 4Matic, GLE 350 4Matic, GLE 350, GLE 550E 4Matic, GLE 63 AMG, GLE 63S AMG, GLE 43 AMG 4Matic Coupe, GLE 63S AMG 4Matic Coupe, GLS 450 4Matic, GLS 550 4Matic, and GLS 63 AMG 4Matic vehicles. In certain types of crash events, the center console may unlatch, allowing the objects within to fly…
Risk and remedy
Risk
In the event of a crash, if objects are not secured within the center console, they may strike the vehicle occupants, increasing their risk of injury.
Remedy
MBUSA will notify owners, and dealers will modify the center console so that it remains latched in a crash, free of charge. The recall is expected to begin in early March 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016-2017 GL350 4Matic Bluetec, GL550 4Matic, GLE350 4Matic, GLE43 AMG Coupe, GLE450 4Matic, 2016 GLE300d 4Matic, GLE350, GLE350d 4Matic, GLE400 4Matic, GLE550e 4Matic, GLE63 AMG, GLE63 AMG 4Matic, GLE63S AMG 4Matic Coupe, and 2017 GLS63 AMG vehicles manufactured April 23, 2014, to May 10, 2016.…
Risk and remedy
Risk
If the front passenger air bag does not deploy as necessary in the event of a crash, the front passenger has an increased risk of injury.
Remedy
MBUSA will notify owners, and dealers will update the OCS software, free of charge. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016-2017 GLE 300d 4MATIC, GLE 350, GLE 350 4MATIC, and GLE 400 4MATIC vehicles manufactured October 14, 2015, to November 23, 2015. The low beam headlights on the affected vehicles may not be properly adjusted. As such, these vehicles fail to comply with the requirements of Federal Motor…
Risk and remedy
Risk
If the low-beam headlights are out of adjustment, the driver's visibility may be reduced, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect and correct the headlight adjustment, as necessary, free of charge. The recall is expected to begin in November 2016. Owners may contact MBUSA customer service at 1-800-367-6372.
Owner complaints
62 complaints6 involved a crash2 injuries
What owners report most
Latest complaints
- Electrical system · Steering · Vehicle speed control
2017 Mercedes-Benz GLE350, VIN [XXX]. While driving, the vehicle intermittently displays multiple warning lights/messages and the power-steering assistance intermittently becomes heavy/stiff. The warnings rapidly appear and disappear and the problem can occur repeatedly while the vehicle is being…
2017 Mercedes-Benz GLE350, VIN [XXX]. While driving, the vehicle intermittently displays multiple warning lights/messages and the power-steering assistance intermittently becomes heavy/stiff. The warnings rapidly appear and disappear and the problem can occur repeatedly while the vehicle is being driven. Pressing/tapping around the front passenger-side floor/kick-panel area can sometimes cause the warnings to clear. The problem appears more frequently in hot daytime conditions and can occur after the vehicle has been running. The engine continues running normally during the events. The vehicle has previously displayed communication-related faults. Mercedes-Benz previously performed Campaign 2023010002 involving inspection for water intrusion in the spare-wheel well; that repair order states no moisture was found in that location and the indicated drain grommet was replaced. The current problem persists. I am concerned because the intermittent loss/reduction of power-steering assistance while driving creates a safety risk. I am also aware of NHTSA Campaign 17V-241 involving water intrusion at the electric power-steering connector and loss of steering assistance on certain Mercedes vehicles. My VIN currently shows no open recalls. I am reporting my vehicle's symptoms so NHTSA can evaluate whether this represents a similar or related safety defect. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Engine · Service brakes · Vehicle speed control
Car took off after going over railroad track, and accelerated without driver being able to control it. The breaks and steering went out as well. It’s like car was being driven remotely. Crashed into fence, and there was no warning. The car accelerated. The car bounces back and forth when brakes are…
Car took off after going over railroad track, and accelerated without driver being able to control it. The breaks and steering went out as well. It’s like car was being driven remotely. Crashed into fence, and there was no warning. The car accelerated. The car bounces back and forth when brakes are on, and again last year stopped in the middle of traffic. Water damage was leaking in as well after 8 months having this car. First major incident was December 2024, but rocking and began one month after purchasing vehicle in August of 2024. Acceleration incident; December 2024: 4 months after purchase; vehicle stopping in traffic: April 2025 8 months after purchase. Apparently new tires were put on. Almost had a blow out within 1 year and 4 months of purchase and found out when getting oil changed this past December 2025. Lights and radio randomly shut off, and gas’s tank is often locked or will not close. This car is scary, and has had problems that someone has covered up for a very long time. I have papers claiming everything was checked upon delivery; However; two incidences alone could have ended in multiple fatalities. Someone is responsible for hiding something something here, and this needs to be reported before someone or multiple people die that is due to a defect in the car. MCC 478-877-5740 478-737-2010
- Unknown or other
I purchased a Certified Mercedes GLE 350 with many advanced safety features. Including a SOS feature that allows I believe detects an accident and reports it to Mercedes as well as allows me to press the SOS button to manually contact Mercedes to report a need for help plus other functions. Thnis…
I purchased a Certified Mercedes GLE 350 with many advanced safety features. Including a SOS feature that allows I believe detects an accident and reports it to Mercedes as well as allows me to press the SOS button to manually contact Mercedes to report a need for help plus other functions. Thnis is a very important safety feature to me as I am getting order and may need assistance. In addition years ago a family friend was involved in a non fatal accident at night and was injured and traped in the car. Although the initial accident was not fatal, because the car was not located for some time and the friend was injured, bu the time the car was located the friend died due to the length of time traped in the car. One of the basic items listed on my Mercedes sell sheet is item 351eCall-emergency system. As I understand it this eCall device is part of the SOS system and is also a critical part of the advanced EMERGENCY and convience systems included with the car such as car locator, remote start and remote lock and unlock, as well as several other featurs I was sold. Recently I was informed by Mercedes that they would be discontinuing this safety feature as of 1/1/2026 and they have not offered any replacment / solution. I recently was on a road trip and caught in a sevier weather situation and tried to use the system and it did not work, which placed me in a potentially dangerious situation. I believe that people will loose their lives because Mercedes has suspended a important emergency safety feature. I have checked with my local Mercedes dealer who contacted Mercedes USA and they told me Mercedes USA is not offering any solution. I believe NHTSA should get involved to require Mercedes USA to find a solution to help prevent the loss of lives. This is an important "emergency system" that was sold as part of the vehicle. It is important to owners of all ages, but even more important to elderly drivers that choose Mercedes for their safety features.
- Unknown or other
Panoramic sunroof suddenly exploded while driving. It was the rear section of the sunroof. There was a loud boom sound. There were no vehicles nearby kicking up rocks, etc. I jumped and screamed but managed to remain somewhat calm trying to figure out where the sound came from in the vehicle. I…
Panoramic sunroof suddenly exploded while driving. It was the rear section of the sunroof. There was a loud boom sound. There were no vehicles nearby kicking up rocks, etc. I jumped and screamed but managed to remain somewhat calm trying to figure out where the sound came from in the vehicle. I then realized it was the panoramic sunroof as sunlight began to trickle into the vehicle. Fortunately, the shade had been pulled closed. Otherwise, more tiny shards of glass would have immediately fallen on me. I handed to situation over to my insurance company for repair.
- Air bags · Vehicle speed control
The contact owned a 2017 Mercedes-Benz GLE350. The contact stated that while slowing at approximately 10 MPH and making a right turn to pull into a driveway, the vehicle unintendedly accelerated and crashed into a fence and came to a stop. The contact had not sustained any injuries, and medical…
The contact owned a 2017 Mercedes-Benz GLE350. The contact stated that while slowing at approximately 10 MPH and making a right turn to pull into a driveway, the vehicle unintendedly accelerated and crashed into a fence and came to a stop. The contact had not sustained any injuries, and medical attention was not needed. A Police report was not filed. The contact stated that the fence was damaged. The vehicle was not diagnosed for the failure but was taken to be repaired. The contact then stated that approximately a year later while driving approximately 20-30 MPH, the brake pedal was depressed, but the vehicle unintendedly accelerated, into ongoing traffic at a cross street. The contact pumped the brake pedal several times to stop the vehicle, but the vehicle failed to slow down as intended. The contact also attempted to turn off the vehicle however, the vehicle failed to turn off. The contact swerved right, and side swiped a fence, and the vehicle went through a front lawn of a house, striking some plants, and then struck a light post. The contact stated that the air bags did not deploy. The contact had not sustained any injuries, but the passenger of the vehicle sustained injuries to the back, knees, legs, arms, scrapes on the head, and general aches all over the body. The passenger was taken to the Emergency Room and medical attention was provided. The contact stated that a Police report was filed. The vehicle was towed to a tow lot where the vehicle was deemed a total loss by the insurance provider. The manufacturer was notified of the failure. The failure mileage was approximately 84,541.
- Unknown or other
I am writing to formally report a serious safety incident involving my Mercedes-Benz vehicle. While driving home recently, without any warning, I heard a sudden explosion that sounded like a gunshot. In an instant, shattered glass fell throughout the interior of the car, covering my daughter…
I am writing to formally report a serious safety incident involving my Mercedes-Benz vehicle. While driving home recently, without any warning, I heard a sudden explosion that sounded like a gunshot. In an instant, shattered glass fell throughout the interior of the car, covering my daughter, grandson, and me. Fortunately, the only other vehicle nearby was at a considerable distance; otherwise, the outcome could have been catastrophic. Our car swerved sharply as a result of the shock. We came to realize that the sunroof had exploded and completely shattered.
- Electrical system
The contact owns a 2017 Mercedes-Benz GLE350. The contact stated that while driving approximately 65 MPH, the center digital screen failed to function as intended while attempting to use the safety features. No warning light was illuminated. The vehicle was taken to a local dealer, where it was…
The contact owns a 2017 Mercedes-Benz GLE350. The contact stated that while driving approximately 65 MPH, the center digital screen failed to function as intended while attempting to use the safety features. No warning light was illuminated. The vehicle was taken to a local dealer, where it was diagnosed, and determined that the command control unit needed to be replaced. The vehicle was not repaired due to the cost. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 65,340.
- Electrical system · Unknown or other · Vehicle speed control
While driving our 2017 MB GLE 350-4matic at about 40 mph, it spontaneously downshifted to M1. We were in traffic, so this was a very dangerous for us and for the people behind us. We limped to our destination, not knowing what had happened or what to do. When we re-started the car the next day, it…
While driving our 2017 MB GLE 350-4matic at about 40 mph, it spontaneously downshifted to M1. We were in traffic, so this was a very dangerous for us and for the people behind us. We limped to our destination, not knowing what had happened or what to do. When we re-started the car the next day, it seemed ok. But after driving some distance, it spontaneously downshifted to M1 again. We stopped the car, turned it off and re-started it. My mechanic checked the car with his analyzer, which showed that the transmission was not transmitting/displaying gear changes. I am taking my car to another repair shop tomorrow that has a more sophisticated analyzer. When I first explored this problem on the web, there was discussion on a MB website about similar problems. Today, I saw that there is an NHTSA probe into 2015-17 Ford 150 pick-ups having a similar problem to mine, i.e., spontaneous downshifting. Maybe there is a chip problem in the transmission control module for cars of those years. This is a significant safety issue. Thank God we were going 40 mph and not 60 or 70 when this happened.
- Engine
Was at a red light turning right, as soon as I turned right the engine lost power, and the car would not move. Since I am pressing the gas pedal all I can hear is revving noise, but the car was not moving. Since my foot was on the gas and not the brakes the person behind me was not aware that my…
Was at a red light turning right, as soon as I turned right the engine lost power, and the car would not move. Since I am pressing the gas pedal all I can hear is revving noise, but the car was not moving. Since my foot was on the gas and not the brakes the person behind me was not aware that my car was not moving forward. The car behind me was barely able to avoid crashing into me and swerved around me. The driver behind me was lucky that there were no cars on his left. The service technician at the dealer informed me that the problem with the engine type that I have is very common. I called Mercedes and was told there is nothing they can do. They should issue a voluntary recall or at least warn drivers and compensate them for repairs needed or was done. There is a flaw in the design of the V167 2.0 engine and Mercedes is aware of it. MBUSA Case# 13095274
- Power train · Vehicle speed control
The transmission does not shift from first to second and created several dangerous situations in whichI tried to enter the highway. I called the corporate headquarters to make a complaint and was sent to the dealership to file a lemon law complaint. The Transmission specialist at AAMCO said the…
The transmission does not shift from first to second and created several dangerous situations in whichI tried to enter the highway. I called the corporate headquarters to make a complaint and was sent to the dealership to file a lemon law complaint. The Transmission specialist at AAMCO said the transmission parts are in good shape, but the problem is that there is too much clearance between the transmission casing and the transmission parts. I told him that this is a defective engineering and these vehicles should be recalled. When I did further research, I found out that I was not alone and that this is a well-documented problem with the Mercedes transmissions. I am reaching out to this agency because I believe that this situation has created a dangerous problem that should be looked into. The following link details these defects. [XXX] The problem with why this has not been reported is that many people that on these cars do not want to look as though they cannot afford the car and just have the vehicle repaired. I truly believe that the government should look into this before someone is seriously hurt because I am not the only one that has had this experience. The repairs/corrections will cost me $7,900 INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Vehicle speed control
On July 3, 2024 I turned right out of a parking lot onto a busy road. The car sped up on its own and started speeding. It took me a couple of seconds to realize what was happening and put on the brake. The car ran through a red light, other cars were able to avoid hitting me. The car did stop…
On July 3, 2024 I turned right out of a parking lot onto a busy road. The car sped up on its own and started speeding. It took me a couple of seconds to realize what was happening and put on the brake. The car ran through a red light, other cars were able to avoid hitting me. The car did stop then. There were no warning signs that this was going to happen. The dealership is going to investigate tomorrow. The car seems to be running fine since.
- Fuel system, diesel · Fuel system, gasoline
The contact owns a 2017 Mercedes-Benz GLE350. The contact stated that the vehicle was previously taken to the dealer, where a water drain plug was installed under NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline). The contact stated while driving 65-70 MPH in the rain…
The contact owns a 2017 Mercedes-Benz GLE350. The contact stated that the vehicle was previously taken to the dealer, where a water drain plug was installed under NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline). The contact stated while driving 65-70 MPH in the rain, the vehicle stalled. The check engine warning light was illuminated. The contact was able to veer to the side of the road. The contact was able to restart the vehicle and drive to the residence. The contact stated that upon starting the vehicle later that day, the check engine warning light was no longer illuminated. The contact stated while driving the following day, the vehicle stalled and failed to restart. The contact was able to veer to the side of the road. The vehicle was towed to an independent mechanic, where it was diagnosed that water accumulation in the spare tire wheel well had damaged the fuel pump control unit, causing the engine to stall while driving. The mechanic determined that the failure was related to NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline). The vehicle was then towed to the dealer, where the same assessment was made; however, the dealer informed the contact that the vehicle could not be repaired under the recall because the recall had already been marked as completed. The vehicle was being repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 85,000.
- Electrical system · Fuel/propulsion system · Unknown or other
Rear trunk lid seal leaking water in rear cargo compartment caused damage to fuel pump. I was driving on a main busy road when without warning the car shut off. The traffic light was about to change so the person behind me was slowing down luckily. There was no warning light, indicator or sound the…
Rear trunk lid seal leaking water in rear cargo compartment caused damage to fuel pump. I was driving on a main busy road when without warning the car shut off. The traffic light was about to change so the person behind me was slowing down luckily. There was no warning light, indicator or sound the car just stopped . It stopped in the middle of the road impeding traffic as it stopped near a 4- way intersection at a busy time of day. The car was towed to dealer after extensive examination it was found to be a leak in rear trunk seal. There was no visible damage to seal or water damage in cargo area. I was told this is problem know to Mercedes as they have issued a bulletin on how to repair it. This has been happening for years without a resolution to this problem. I was told in my case it had been leaking over an extended amount of time and there was know way to discover it until the damage is done. I find that hard to believe that Mercedes would not recall this and find a remedy before it results in a serious accident or death. A car stopping on busy road or highway with a fast speed of traffic following is a tragedy waiting to happen. I had no warning of the potential danger I was in until it happened. The damage it causes is around $1,600 for a rubber piece that gets loose and allows water to damage the fuel pump. And because that piece is not covered under extended warranty the burden is put on the owner which it unfair to say the least.
- Exterior lighting
I purchased a 2017 MB GLE 350 in 2022. But it’s only recently where I’ve noticed that my halogen headlights do not provide enough light on the road during night time driving. Especially in the rain. I’ve researched a bit and see that MANY consumers have complained about the headlights, but there is…
I purchased a 2017 MB GLE 350 in 2022. But it’s only recently where I’ve noticed that my halogen headlights do not provide enough light on the road during night time driving. Especially in the rain. I’ve researched a bit and see that MANY consumers have complained about the headlights, but there is no solution as MB does not offer an aftermarket upgrade. I either have to drive with my high beams on,or not drive at night. The other alternative is to buy another car which is ridiculous. For the price of this car, the exterior lighting should be better.
- Engine · Fuel/propulsion system
The car losses acceleration power all of sudden while driving. The engine light comes on and car starts shaking. Once you turn off the car and restart it, the engine light goes away and car starts functioning normal. This is dangerous as you are on highway, among fast moving traffic. This has been going for over a year.
- Latches/locks/linkages › Doors › Latch · Unknown or other
I am writing to bring to your attention a critical security issue regarding the rear door locks of the 2017 Mercedes GLE model VIN - [XXX] . Upon attempting to lock the vehicle using the key fob, I have encountered a malfunction where the rear door behind the passenger seat fails to secure…
I am writing to bring to your attention a critical security issue regarding the rear door locks of the 2017 Mercedes GLE model VIN - [XXX] . Upon attempting to lock the vehicle using the key fob, I have encountered a malfunction where the rear door behind the passenger seat fails to secure properly. Despite attempts to engage the locking mechanism, this specific door remains open, triggering the vehicle alarm system when accessed. This issue poses a significant safety risk for both occupants and belongings within the vehicle. As a concerned consumer, I am deeply troubled by the presence of such a critical flaw in a luxury automobile. Given the potential ramifications for driver and passenger security, I urge the National Highway Traffic Safety Administration (NHTSA) to conduct a thorough investigation into the root cause of this malfunction. It is imperative that swift action be taken to address and rectify this security vulnerability to ensure the continued safety and peace of mind for Mercedes GLE owners and their families. Thank you for your attention to this matter. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Exterior lighting
Low beam Headlights will not adjust properly
- Steering
The contact owns a 2017 Mercedes GLE. The contact stated that while driving at an undisclosed speed, he became aware that the electronic power steering was not functioning properly. The contact was able to pull to the shoulder of the roadway, where the failure persisted. The vehicle was towed to…
The contact owns a 2017 Mercedes GLE. The contact stated that while driving at an undisclosed speed, he became aware that the electronic power steering was not functioning properly. The contact was able to pull to the shoulder of the roadway, where the failure persisted. The vehicle was towed to the dealer, who diagnosed a failure with the electronic power steering. The vehicle was repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 17V574000 (Steering), but the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was 23,000.
- Fuel/propulsion system
This vehicle had a recall to place a water drain in the rear truck section to drain water if it somehow entered the vehicle to prevent the fuel pump module from failing. This vehicle suddenly stalled and was towed to the dealer. The dealer reports the vehicle had water Intrusion as reported by the…
This vehicle had a recall to place a water drain in the rear truck section to drain water if it somehow entered the vehicle to prevent the fuel pump module from failing. This vehicle suddenly stalled and was towed to the dealer. The dealer reports the vehicle had water Intrusion as reported by the dealer and subsequently the fuel pump module was exposed to water and failed which the recall was to prevent if occurred requiring repair and replacement of the fuel pump control module not covered by the dealer
- Suspension
01/22/2024 NHTSA Complaint – GLE350 4Matic The front suspension, either the control arm or upper arm, feels loose and noise is coming from the front suspension as if a bolt or bolts are loose. Base on recall information for the 2016 GLE350 4Matic, NHTSA campaign ID: 17V081000, REPORT DATE…
01/22/2024 NHTSA Complaint – GLE350 4Matic The front suspension, either the control arm or upper arm, feels loose and noise is coming from the front suspension as if a bolt or bolts are loose. Base on recall information for the 2016 GLE350 4Matic, NHTSA campaign ID: 17V081000, REPORT DATE 02/07/2017, the loose bolt(s) may cause improper wheel tracking, increasing the risk of a crash. Vehicle owners are instructed to contact dealer to inspect the tightness of the bolt connecting the upper control arm and the axle stub on the affected vehicles, replacing the upper control arm, if necessary, free of charge. The recall began March 2017. I request that NHTSA add my vehicle VIN number to the recall and add all GLS 350 4Matic vehicles to the recall for model year 2017. I do not want my wife or I to be involve in a crash as a result of the negligence and poor-quality control of Mercedes Benz. I contacted MBUSA and Hendrik Mercedes of Charlotte, NC on 01/22/2024 and both refuse the inspect and fix the issue without me paying for the resolution. I told them that I refuse to pay to fix a problem that is the result of poor-quality control and quality assurance. I requested that MBUSA pay to fix the issue as they have done for the 2016 GLE350 4MATIC with the same problem. I am fearful for the life of my family. This matter is of very serious concern to my family's life, health and well-being. Please address this matter immediately, as we drive the SUV daily.
- Service brakes
The contact owns a 2017 Mercedes-Benz GLE350. The contact stated that while driving at an undisclosed speed, the vehicle was in the hold brake position while at a complete stop. The contact stated that the vehicle independently moved forward twice. The contact stated that the failure caused her to…
The contact owns a 2017 Mercedes-Benz GLE350. The contact stated that while driving at an undisclosed speed, the vehicle was in the hold brake position while at a complete stop. The contact stated that the vehicle independently moved forward twice. The contact stated that the failure caused her to rear-end the vehicle in front. A police report was filed. The contact also stated that damage was done to both vehicles. The vehicle was taken to the dealer. The dealer was unable to duplicate the failure. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 41,300.
- Other/i am not sure
When the car seat is in the rear facing position and in the most upright position the rear of the seat can be lifted off the base with very little force. I have videos that show this behavior but photos don't really do it justice.
- Steering
While traveling at approximately 45 MPH in multi-lane highway traffic, WITHOUT WARNING the vehicle's power steering suddenly failed. Concurrently a red display message appeared in the instrument cluster stating "Power Steering Malfunction - See Owner's Manual". ALL steering assistance was lost at…
While traveling at approximately 45 MPH in multi-lane highway traffic, WITHOUT WARNING the vehicle's power steering suddenly failed. Concurrently a red display message appeared in the instrument cluster stating "Power Steering Malfunction - See Owner's Manual". ALL steering assistance was lost at that point and the vehicle had to be maneuvered with great effort out of traffic to a safe offroad location. Vehicle is a 2017 Mercedes GLE 350 (166 chassis) with 22,000 miles. Initial inspection of the vehicle by a Mercedes mechanic revealed a fault in the EPS (electrical power steering), and the presence of fault code P063500. Subsequent inspection of the vehicle by the local Mercedes dealer revealed the same fault code along with the advisory that the vehicle is "technically not safe to drive..." and that a new electric power steering rack is required. Service advisor further offered the comment that "1-2 vehicles present like this monthly." Online search of Mercedes Xentry Tips for fault code P063500 reveals topic number LI46.35-P-0555436 (dated 01-12-2017), with the acknowledgement of power steering malfunction occurrences in model 204, 207 and 212 vehicles. No reference is made to model 166 vehicles. Mention is made of performing a software update of the electric power steering control unit via "Adaptations" in the 204, 207 and 212 vehicles.
- Unknown or other
My sunroof exploded for no reason. There was no accident or impact. The car was stationary and the glass just blew out.
- Fuel/propulsion system
This letter is an attempt to connect to the correct channels seeking resolution regarding a recent recall. My 2017 Mercedes GLE350 stalled in the rain and I subsequently had to get it towed to the dealership for repairs. And upon completion of the repairs, I received a recall notice about the…
This letter is an attempt to connect to the correct channels seeking resolution regarding a recent recall. My 2017 Mercedes GLE350 stalled in the rain and I subsequently had to get it towed to the dealership for repairs. And upon completion of the repairs, I received a recall notice about the specific issue that was just addressed. Pursuant to the recall notice, I sought a reimbursement for the repairs in which I was directed to Mercedes Customer Care and received a case number. The dealership is being a little hard-nosed regarding the reimbursement so I’m seeking recourse through official channels. I’ve attached the recall notice, invoice of repairs, and all other pertinent information regarding this issue. An expedient resolution would be greatly appreciated. Thank you and looking forward to hearing from you.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010750Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to FIN vehicle identification end number. If vehicle falls outside of FIN range, create a TIPS case. Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008070Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to VIN vehicle identification end number. If vehicle falls outside of VIN range, create a TIPS case. Model series 192: xxx xxx xx 182881 Model series 232: xxx xxx xx 182883 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10208744Complaint The touchpad dimming function does not work and the search lighting is either at maximum brightness or fully off (dependent upon dimming signal). Note: The dimming functions of the instrument cluster and head unit display are not affected and remain fully functional. Cause Touchpad (A105) hardware Remedy The serial numbers of the potentially affected parts can be found in the attached list. The serial number can be found on the touchpad itself or in Vedoc (Vedoc -> control units -> TPAD -> serial number). If the serial number listed in VeDoc or on the part (these numbers should be identical) matches one of the serial numbers in the attachment and the described complaint is present, then the touchpad may be replaced.
- 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
- 10205835Model series 167 noise on B/C/D pillars.
- 10205819Important new emission service campaign information.
- 10205814Fuel filler flap opens slowly/switch flashes/tank is bleeding instrument cluster warning
- 10205257Model indicator index.
- 10205251Engine fan runs continuously, a/c inoperable or, engine light illuminates sporadically.
- 10205250Engine fan runs continuously, a/c inoperable or, engine light illuminates sporadically.
- 10205154Gasket may settle causing a slight oil leak.
- 10205147Ticking or pulsing noise from high-pressure pump and/or fuel injectors.
- 10202531Touch pad: Search lighting does not dim or does not turn on.
- 10199774Launch NCU 2021070020- Perform SCN coding in powertrain control unit
- 10195220For plug in hybrid and electric variants: Complaints about the electric range
- 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
- 10186145Creaking noise from fixed glass section of panoramic roof in area of rear passenger compartment grab handles
- 10184798Replace charge air hose between charge air cooler and turbocharger
- 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
- 10179904Implausible "service due" instrument cluster message, head unit pop-up, or Mmc message
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
Every Mercedes-Benz GLE350 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.