2018 Mercedes-Benz GLE 350
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › GLE 350 › 2018
These records cover every 2018 Mercedes-Benz GLE 350. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2018 Mercedes-Benz GLE 350. Newest first.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML550, 2012-2015 ML350, AMG ML63, 2015 ML250, ML400, 2016 GLE450, GLE300, 2016-2018 GLE350, GLE550, 2016-2019 GLE400, 2017-2019 AMG GLE43, and 2016-2020 AMG GLE63 vehicles. Water might accumulate in the spare tire wheel well and damage the fuel pump control unit, which could cause an engine…
Risk and remedy
Risk
An engine stall while driving increases the risk of a crash.
Remedy
Dealers will install a water drain plug, inspect for water intrusion, and replace the fuel pump control unit as necessary, free of charge. Owner notification letters were mailed February 15, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers for this recall are 2023010002 and 2023010003.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018 GLE350, GLE43 AMG, and GLE400 vehicles equipped with Continental tires. The affected tires were cured for too long during production.
Risk and remedy
Risk
Over cured tires may develop a break in the sidewall, resulting in sudden air loss or belt edge separation which could lead to tread/belt loss. Either condition can cause a loss of vehicle control, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect the tires, and replace them as necessary, free of charge. The recall began April 23, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021030008.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2019 C300, E300, 2018-2020 CLA250, 2020 CLS450, AMG E53, AMG GT53, GLE450, 2018 AMG E63, AMG GTA, 2017-2020 GLA250, GLC300, 2019 GLC350, AMG GLC43, 2017-2018 GLE350, 2019 AMG GLC 43, GLC350, GLE400, 2017 GLS450, S550, C300 Cabrio, and 2018-2019 S560 vehicles. On June 18, 2021, an additional 9…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting emergency services through the call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the communication module and activate it, if necessary, free of charge. The recall began March 31, 2021. Letters for the owners of the 9 additional vehicles were mailed July 9, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021030005.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018 Mercedes-Benz GLE350 4Matic, GLE350, GLS450 4Matic, GLS550 4matic, GLE43 AMG 4Matic, GLE63 AMG 4Matic, GLE63S AMG 4Matic, and GLS63 AMG 4Matic vehicles. The rear brake caliper pistons on these vehicles may not have been correctly coated, causing gas to become temporarily released into the rear brake…
Risk and remedy
Risk
Reduced braking performance can increase the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will bleed the rear axle brake system, free of charge. The recall began September 14, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018080013.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018 GLE350, GLE350 4Matic, and GLE43 AMG vehicles. During manufacturing, components of the panoramic sunroof may have been installed with a bonding primer that was incorrectly made, possibly affecting the long-term adhesion to the vehicle.
Risk and remedy
Risk
If the front cover and/or rear fixed glass are not properly adhered, they may detach, creating a road hazard and increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect the panoramic sunroof, replace it if necessary, free of charge. The recall began September 7, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018080006.
Owner complaints
40 complaints5 involved a crash2 injuries1 deaths
What owners report most
Latest complaints
- Back over prevention › Sensing system › Camera
Rear view camera fails to initiate when placed in reverse. Screen doesn’t even try to switch to camera view. Exact same issue found in same make and model recalled with different vins. For some reason this one isn’t included in the recall. Car only has about 58,000 miles. Started around 56,000 miles. Note that camera even folds out of lift gate like normal when placed in park.
- Electrical system · Unknown or other
CASE NUMBER: [XXX] VEHICLE: 2018 Mercedes-Benz GLE350 --- EMAIL EXCHANGE TEXT --- From: [XXX] Sent: 1/14/2026, 12:11 PM To: cs.usa@mercedes-benz.com Subject: Re: Message From Mercedes-Benz USA: Case Number [XXX] Dear Ken, I want to clarify that my concern is not about support for “older…
CASE NUMBER: [XXX] VEHICLE: 2018 Mercedes-Benz GLE350 --- EMAIL EXCHANGE TEXT --- From: [XXX] Sent: 1/14/2026, 12:11 PM To: cs.usa@mercedes-benz.com Subject: Re: Message From Mercedes-Benz USA: Case Number [XXX] Dear Ken, I want to clarify that my concern is not about support for “older technology” in a general sense, but about the confirmed retirement of factory-installed emergency and crash-response systems that were standard safety equipment on my vehicle at the time of sale. As previously noted, the mbrace system on my 2018 GLE-Class includes SOS/Emergency Call and Automatic Collision Notification functionality intended to contact emergency services in the event of a crash or airbag deployment, particularly where the driver may be incapacitated. These are safety systems, not discretionary convenience features. Your replies confirm that these safety functions are being permanently disabled, that no retrofit or replacement solution exists, and that the vehicle will continue to operate without the emergency communication capability it was originally sold with. I appreciate your acknowledgment, and I am documenting Mercedes-Benz USA’s position that these safety systems have been retired with no alternative provided. Sincerely, [XXX] On Jan 14, 2026, at 09:02, Mercedes-Benz USA cs.usa@mercedes-benz.com wrote: Dear [XXX] , I’m very sorry that these older technology features have been retired. Mercedes‑Benz is currently focused on supporting our present and next‑generation technologies, which unfortunately means that the former mbrace system is no longer maintained. If you have any additional questions or concerns, I would be more than happy to assist. Best Regards, Ken C. Mercedes-Benz USA (800) 367-6372 Mercedes-Benz Customer Care, 1 Mercedes-Benz Drive. Sandy Springs, GA 30328 INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Exterior lighting
The low beam visibility on this vehicle is extremely dangerous. It's as if you have no headlights on. They can inspect anytime. With low night visibility. Driver is not able to see the road or person which causes a delayed response because of visibility. Driver puts on highbeams to be able to…
The low beam visibility on this vehicle is extremely dangerous. It's as if you have no headlights on. They can inspect anytime. With low night visibility. Driver is not able to see the road or person which causes a delayed response because of visibility. Driver puts on highbeams to be able to see which blinds others or shouldn't be driven at night. Plenty of times, I could have been in an accident or didn't see someone. My eyes are 20/20. Yes, it was reproduced. We tried after market headlights as well, but it's the same issue. Yes, I have complained to manufacturer more than once, but if there is no recall. They want a diagnostic fee and ignore it. This has been ongoing since the car was purchased. Even the GLS 2017 have the same issue.
- Electrical system
Mercedes-Benz USA, LLC; Case: XXX My concerns has been denied and overlooked by Mercedes-Benz USA, LLC multiple times since Jan 2026--interims of defective electric system causing sudden locking of steering wheel and shut down car , due to malfunctioning electric system resulting in car crash into…
Mercedes-Benz USA, LLC; Case: XXX My concerns has been denied and overlooked by Mercedes-Benz USA, LLC multiple times since Jan 2026--interims of defective electric system causing sudden locking of steering wheel and shut down car , due to malfunctioning electric system resulting in car crash into another parked car on the street, took car to auto body shop who diagnosed gas gauge misread as empty gas tank even though tank was 3/4 full , due to this car was totally locked out when driving on the street and hit another parked car due to loss of control. i have been in communication with Mercedes and they stated car was functioning fine and there was no defect or malfunction ,which i don't agree, as a results my wife into crash and sustained injuries I need your help to resolve this issue thx [XXX] & [XXX] [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Service brakes · Vehicle speed control
The contact owns a 2018 Mercedes-Benz GLE 350. The contact stated that while the vehicle was parked in a pharmacy parking lot with the hold feature engaged, the driver released the brake pedal. Immediately afterward, the vehicle suddenly accelerated forward approximately 75 feet. The driver…
The contact owns a 2018 Mercedes-Benz GLE 350. The contact stated that while the vehicle was parked in a pharmacy parking lot with the hold feature engaged, the driver released the brake pedal. Immediately afterward, the vehicle suddenly accelerated forward approximately 75 feet. The driver attempted to stop the vehicle by depressing the brake pedal; however, the brakes failed to respond. The vehicle continued moving, went over a curb, into a ditch, up a hill, and through a cement block wall before coming to an abrupt stop 5 feet from a house. The driver sustained arm and shoulder injuries, including emotional trauma, and was transported by ambulance to a hospital for medical treatment. The air bags deployed during the crash. There was no reported fire. A police report was filed, and the vehicle was towed to a tow lot. The driver attempted to contact a local dealer but did not receive a response. The vehicle has not yet been diagnosed or repaired. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 91,000.
- Unknown or other
Owners of affected Mercedes-Benz vehicles were given no meaningful advance warning that core, built-in safety and emergency communication systems would be permanently disabled. No replacement system has been offered, no retrofit path exists, and no alternative emergency solution has been provided.…
Owners of affected Mercedes-Benz vehicles were given no meaningful advance warning that core, built-in safety and emergency communication systems would be permanently disabled. No replacement system has been offered, no retrofit path exists, and no alternative emergency solution has been provided. The manufacturer has instead unilaterally orphaned these vehicles by discontinuing backend support required for functionality that was present at the time of sale. These vehicles were manufactured and sold with non-paywalled, standard safety features, including automatic emergency call (E-Call/SOS), crash notification, and airbag deployment communication designed to contact emergency services when a driver may be incapacitated. With the discontinuation of backend services, these safety-critical functions will no longer operate, meaning there will be no automatic communication of airbag deployment, crash events, or emergency assistance requests, despite the physical hardware remaining installed in the vehicle. In addition, connected vehicle functions that support vehicle location, tracking, and remote access—features that can materially assist in emergency response, theft recovery, and post-collision assistance—were removed without explanation, compensation, or transition plan. These systems simply ceased to function, leaving owners without clarity, notice, or recourse. As a result of these actions by Mercedes-Benz, affected vehicles are now materially less safe than when purchased, through no fault or action of the driver or owner. A vehicle originally marketed and sold with integrated emergency response capability has been degraded after sale, creating a safety risk in precisely the situations these systems were designed to address. This issue concerns the post-sale removal of safety-critical functionality, not optional convenience features, subscriptions, or infotainment services.
- Engine
While driving, the vehicle’s serpentine/fan belt snapped. The loose belt struck and pulled out a sensor plug. Immediately the engine shut down and was later found to be seized. The vehicle had no prior warnings or known issues and was maintained according to manufacturer recommendations. There were…
While driving, the vehicle’s serpentine/fan belt snapped. The loose belt struck and pulled out a sensor plug. Immediately the engine shut down and was later found to be seized. The vehicle had no prior warnings or known issues and was maintained according to manufacturer recommendations. There were no other warning signs ahead, the car is always maintained. I have records of all the maintenance, and there was not a single Check engine light, or any other kind of issue. Consequence: Engine seized, vehicle not drivable, substantial repair or replacement required. •Condition & maintenance: All services up-to-date, regular oil changes, no previous related issues. •Supporting documentation: Mechanic’s inspection report, service records, tow bill, photos of belt damage and sensor plug. •Impact: Unexpected catastrophic failure at low mileage; potential defect in belt/pulley/auxiliary-system interface posing risk of sudden breakdown. •Request: Investigation of whether this is an isolated failure or a possible defect pattern.
- Electrical system · Fuel/propulsion system
The fuel pump has been failing and shutting off and has been hesitant when taking off. It can leave you stranded in the middle of the road or if you turn left in front of people the car may stall and can cause a crash. Yes and independent dealer and the dealer both know it’s a problem. I took the…
The fuel pump has been failing and shutting off and has been hesitant when taking off. It can leave you stranded in the middle of the road or if you turn left in front of people the car may stall and can cause a crash. Yes and independent dealer and the dealer both know it’s a problem. I took the vehicle into a Mercedes dealer and the fuel pump had a recall on it and the dealer refused to replace it although I had a engine code that they could pull up referring them to the fuel pump and the fuel pump not priming as it should in every start up. The failure happened a few months ago and I took it in and the dealer drilled a home in the rear of my car and failed to replace the fuel pump, which was covered under the warranty. And the dealer admitted there was water in the trunk area which corroded the fuel pump.
- Power train
Cannot shift the gear from P to any other positions, and unable to move the car. The issue has been existing from mid 2022, three years ago.
- Power train
After fully stop with pressing brake pedal, try to shift the gear from D (Drive) to R (Reverse) but cannot shift the automatic gear position from D to R (reverse) gear. In order to shift to R gear position, I needed to shutdown and restart the engine. This has been clearly recurrent since 3 years…
After fully stop with pressing brake pedal, try to shift the gear from D (Drive) to R (Reverse) but cannot shift the automatic gear position from D to R (reverse) gear. In order to shift to R gear position, I needed to shutdown and restart the engine. This has been clearly recurrent since 3 years ago and mostly happen in front of my garage to park backward, but sometimes very dangerous in the middle of road, when needed to make tight U-turn. Please take care of this issue. Thank you.
- Electrical system · Structure
The contact owns a 2018 Mercedes-Benz GLE 350. The contact stated that water had entered the vehicle through the sunroof. The vehicle was taken to an independent mechanic, who determined that water intrusion through the sunroof had damaged the batteries. The mechanic replaced both batteries. The…
The contact owns a 2018 Mercedes-Benz GLE 350. The contact stated that water had entered the vehicle through the sunroof. The vehicle was taken to an independent mechanic, who determined that water intrusion through the sunroof had damaged the batteries. The mechanic replaced both batteries. The contact related the failure to NHTSA Campaign Number: 23V854000(Structure); however, the VIN was not included in the recall. The dealer was notified of the failure. The vehicle was not repaired for the water intrusion failure. The manufacturer was made aware of the failure. The failure mileage was approximately 81,000. The VIN was unavailable.
- Back over prevention › Sensing system › Camera
The contact owns a 2018 Mercedes Benz GLE350. The contact stated that while operating the vehicle in reverse, the backup camera screen display had malfunctioned and a black image had been displayed, creating a visibility hazard for the driver. The contact indicated that the failure was…
The contact owns a 2018 Mercedes Benz GLE350. The contact stated that while operating the vehicle in reverse, the backup camera screen display had malfunctioned and a black image had been displayed, creating a visibility hazard for the driver. The contact indicated that the failure was intermittent. The cause of the failure was not yet determined. The manufacturer was notified of the failure and informed that the VIN was not included in the manufacturer's extended coverage related to the failure. No further information was available. The local dealer was not yet contacted. The failure mileage was 69,000.
- Fuel system, diesel · Fuel system, gasoline
The contact owns a 2018 Mercedes-Benz GLE350. The contact stated that the vehicle failed to start. The contact scanned the vehicle with a vehicle scanner and retrieved diagnostic trouble codes that indicated a loss of communication between the fuel pump control unit and the fuel pump. The vehicle…
The contact owns a 2018 Mercedes-Benz GLE350. The contact stated that the vehicle failed to start. The contact scanned the vehicle with a vehicle scanner and retrieved diagnostic trouble codes that indicated a loss of communication between the fuel pump control unit and the fuel pump. The vehicle was towed to the dealer, where the contact was informed that there was water accumulation in the spare tire wheel well. The dealer replaced the blown seals and the fuel pump control unit under NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline); however, the failure persisted. The dealer recommended a fuel pump replacement. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 132,000.
- Fuel/propulsion system
The vehicle will not turn over and start. Unable to drive to work, water accumulated in the back spare tire area. No warning or alerts appeared on the dash the vehicle would not turn over.
- Air bags
The contact owns a 2018 Mercedes-Benz GLE350. The contact stated while starting the vehicle, the air bag warning light was illuminated, and the message "Front Left Malfunction. Service Required" was displayed. The vehicle was taken to an independent mechanic to be diagnosed. The mechanic informed…
The contact owns a 2018 Mercedes-Benz GLE350. The contact stated while starting the vehicle, the air bag warning light was illuminated, and the message "Front Left Malfunction. Service Required" was displayed. The vehicle was taken to an independent mechanic to be diagnosed. The mechanic informed the contact that the front driver's side air bag might fail to deploy during a crash, and that an unknown part needed to be replaced. The dealer was notified of the failure and charged a fee for the repair. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 46,000.
- Power train
After 60,000 miles the seal of the the cylinder head cover starts to leak. It takes around $1800 to fix and the reseal. The material use to release is way better and lasts longer compared to what car comes with. This I found out from the Mercedes Benz service department. Due to this leak the car…
After 60,000 miles the seal of the the cylinder head cover starts to leak. It takes around $1800 to fix and the reseal. The material use to release is way better and lasts longer compared to what car comes with. This I found out from the Mercedes Benz service department. Due to this leak the car starter gets soaked in the engine oil and car is enabled to even start up. Lots of customers end up toeing their cars to Mercedes dealer. The complaint is that Mercedes is putting the parts on their car that are cheap and going to last only 60k that is cheating and once user pays for the repairs they will put much better part. This leak has happened to my car and With only 60k miles on it. Mercedes Benz is cheating the people by putting the cheapest part and charging premium on cars. They label this as normal wear and tear, even tho car is kept well maintained. They put on much better seal after the seal and charging customers $1800. They could have use this seal first time when car was being made. I have been owner of Toyota. Honda, infinity and family member owned BMW, Jaguar and no car had this problem for the life of car( 200,000 to 300,000) miles and I have never heard of this issue until now. Even this is happening at 65,000 miles right after the warranty is expired. This is cheating, I am not getting this done unless Mercedes pays for it CYLINDER HEAD FRONT COVERS LEAKING, RESEAL AND CLEAN FRONT COVERS
- Tires
The contact owns a 2018 Mercedes-Benz GLE350 equipped with Kenda Tires, Tire Line: Klever, Tire Size: 255/50/R19, DOT Number: (N/A). The contact stated while driving 35 MPH, there was an abnormal popping sound coming from the vehicle. Upon inspection, the contact discovered that the front…
The contact owns a 2018 Mercedes-Benz GLE350 equipped with Kenda Tires, Tire Line: Klever, Tire Size: 255/50/R19, DOT Number: (N/A). The contact stated while driving 35 MPH, there was an abnormal popping sound coming from the vehicle. Upon inspection, the contact discovered that the front passenger’s side tire had experienced a blowout. The contact had the vehicle towed to an independent mechanic and was informed that all four tires were in bad condition and that all four tires needed to be replaced. The front passenger’s side tire was patched, and the vehicle was towed back to the residence. The manufacturer and the dealer who sold the contact the tires were notified of the failure but offered no assistance. The tires were not replaced. The tire failure mileage was approximately 1,000. The vehicle failure mileage was 35,040.
- Electrical system · Power train
Transmission gear does not shift into R or N or D, from P. How to reproduce: Drive several minutes, then brake/stop, shift into R, pull back 10~20 ft. Gear cannot shift to either R or N or D. Gear can only shift into P. Shutdown the car, restart the engine then able to shift into R or N or D. This has been intermittent but getting more frequent.
- Service brakes, hydraulic › Foundation components › Disc › Rotor · Wheels
The contact owns a 2018 Mercedes-Benz GLE350. The contact stated that while entering the dealer, the over-the-thread detector provided an alert. There were no warning lights illuminated. While at the local dealer, the contact was informed that the vehicle was working as designed. The vehicle was…
The contact owns a 2018 Mercedes-Benz GLE350. The contact stated that while entering the dealer, the over-the-thread detector provided an alert. There were no warning lights illuminated. While at the local dealer, the contact was informed that the vehicle was working as designed. The vehicle was not diagnosed or repaired. The vehicle was taken to another local dealer Mercedes-Benz of Buckhead (2799 Piedmont Rd NE, Atlanta, GA 30305) where it was diagnosed that the brake pads had separated and were not engaged. The brake pads and rotors were replaced but the failure recurred. The vehicle was taken back to the dealer and the contact was informed that the rear passenger’s side wheel was scraping and there was an abnormal pattern on the rotor. The vehicle was not repaired. The manufacturer was contacted but provided no assistance. The failure mileage was approximately 37,873.
- Power train
Was not able to change automatic transmission gear to R (Reverse) w/o restarting the engine. (the brake pedal is firmly pressed for sure) For all three cases: 1) D (Drive) to R or 2) P (park) to R or 3) N to R. The only way to change to R was: 1) move gear to P 2) shutoff the engine, 3) restart the engine, 4) and then able to change the gear to R. This has happened several times in this year, 2023.
- Fuel system, diesel · Fuel system, gasoline · Structure
The contact owns a 2018 Mercedes-Benz GLE350. The contact stated that while driving at an undisclosed speed, the vehicle stalled without warning. No warning lights were illuminated. The vehicle was towed to the dealer where it was diagnosed that water had intruded into the connector and the fuel…
The contact owns a 2018 Mercedes-Benz GLE350. The contact stated that while driving at an undisclosed speed, the vehicle stalled without warning. No warning lights were illuminated. The vehicle was towed to the dealer where it was diagnosed that water had intruded into the connector and the fuel pump control unit needed to be replaced. The vehicle was repaired; however, after the vehicle was retrieved, the failure recurred. The contact stated while driving approximately 70 MPH, the vehicle stalled without warning. The contact then stated that upon inspecting the vehicle, she noticed that water had collected in the wheel well and caused the wheel well to rust. Additionally, the contact stated that she noticed that water had collected in the spare tire, the battery, and the body of the vehicle. The contact also stated that the water caused mold and rust throughout the vehicle. The vehicle was towed to a specialist where the cause of the failure could not be determined. The vehicle was not repaired. The contact then stated that she was not made aware of the NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline). The vehicle was not repaired. The manufacturer was notified of the failure and the contact was informed that the dealer was handling the recall, but no further assistance was provided. The failure mileage was approximately 50,000.
- Fuel system, diesel · Fuel system, gasoline
The contact owns a 2018 Mercedes-Benz GLE350. The contact received notification of NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount…
The contact owns a 2018 Mercedes-Benz GLE350. The contact received notification of NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue. The manufacturer was made aware of the issue. The contact had experienced not a failure. VIN tool confirms parts not available.
- Service brakes
when i tried to apply brakes on Nov 27th, 2022, the brakes were not applying for 4-5 seconds inspite of pushing the brake few times. After 5 seconds the brakes were working. to avoid collision i had to change the lane quicKly and luckily there was no one in the next lane. Please note that i have…
when i tried to apply brakes on Nov 27th, 2022, the brakes were not applying for 4-5 seconds inspite of pushing the brake few times. After 5 seconds the brakes were working. to avoid collision i had to change the lane quicKly and luckily there was no one in the next lane. Please note that i have changed the front and rear brake pads few months back (Aug 2022). As my brake pads are new, i assume there is some fault in the overall brake system which I would like to bring notice to the United States transportation Department and to the Mercedes company. Please advise on how to proceed from here to ensure my car is safe.
- Power train
Cannot shift gear to Reverse or Neutral, after car is completely stopped by pushing brake pedal and keep firmly pushing the brake pedal. After firmly press the brake pedal, tried to move hear selector to Reverse or Neutral, but did not work. Tried to above step more than five times at the moment of…
Cannot shift gear to Reverse or Neutral, after car is completely stopped by pushing brake pedal and keep firmly pushing the brake pedal. After firmly press the brake pedal, tried to move hear selector to Reverse or Neutral, but did not work. Tried to above step more than five times at the moment of incident, but did not work. If takes off the foot from the pedal, the car Restart the engine, then I was able to move the gear to Reverse or Neutral The case has occurred three times, an year ago (Summer, 2021), Aug 2022, Sep 3, 2022. Q:How was your safety or the safety of others put at risk? When incident happened, after trying changing the gear to Reverse, take off the foot from the pedal then car moved to forward instead of backward, then immediately braked the car again to stop moving the car. Q:Has the problem been reproduced or confirmed by a dealer or independent service center? No. Have not brought the car to the dealership yet. Cannot reproduce it most of the time. Q:Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? No. Cannot reproduce it most of the time. Q:Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? There seems a message that "Cannot change the gear to Reverse".
- Power train › Automatic transmission
The contact owned a 2018 Mercedes-Benz 350 GLE. The contact stated while stopped at a traffic light at an intersection, the vehicle began to lunge forward while the brake pedal was still depressed. The vehicle lurched into the intersection and struck another vehicle. The contact stated he did not…
The contact owned a 2018 Mercedes-Benz 350 GLE. The contact stated while stopped at a traffic light at an intersection, the vehicle began to lunge forward while the brake pedal was still depressed. The vehicle lurched into the intersection and struck another vehicle. The contact stated he did not notice any warning lights being illuminated. The contact's vehicle struck a vehicle on the driver's side door with his front end. The vehicle's grill was crushed and shattered all the windows on the other vehicle's driver's side. There were no injuries. The police were on the scene and wrote a report. The contact had the vehicle towed to a local dealer, where it was placed in the body shop and repaired. The vehicle was not diagnosed. The manufacturer had not been informed of the failure. The failure mileage was approximately 44,500. The VIN was not available.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010750Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to FIN vehicle identification end number. If vehicle falls outside of FIN range, create a TIPS case. Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008070Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to VIN vehicle identification end number. If vehicle falls outside of VIN range, create a TIPS case. Model series 192: xxx xxx xx 182881 Model series 232: xxx xxx xx 182883 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10241527Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customers vehicle. The OTA may be validated as successful on the customers Mercedes Me connect app under Over-the-Air Vehicle Updates as Update for the communication module. If the OTA is successful it will show a green installed and date of installation in the Over-the-Air update section.
- 10208744Complaint The touchpad dimming function does not work and the search lighting is either at maximum brightness or fully off (dependent upon dimming signal). Note: The dimming functions of the instrument cluster and head unit display are not affected and remain fully functional. Cause Touchpad (A105) hardware Remedy The serial numbers of the potentially affected parts can be found in the attached list. The serial number can be found on the touchpad itself or in Vedoc (Vedoc -> control units -> TPAD -> serial number). If the serial number listed in VeDoc or on the part (these numbers should be identical) matches one of the serial numbers in the attachment and the described complaint is present, then the touchpad may be replaced.
- 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
- 10205835Model series 167 noise on B/C/D pillars.
- 10205814Fuel filler flap opens slowly/switch flashes/tank is bleeding instrument cluster warning
- 10205251Engine fan runs continuously, a/c inoperable or, engine light illuminates sporadically.
- 10205250Engine fan runs continuously, a/c inoperable or, engine light illuminates sporadically.
- 10205154Gasket may settle causing a slight oil leak.
- 10205147Ticking or pulsing noise from high-pressure pump and/or fuel injectors.
- 10202531Touch pad: Search lighting does not dim or does not turn on.
- 10199774Launch NCU 2021070020- Perform SCN coding in powertrain control unit
- 10195220For plug in hybrid and electric variants: Complaints about the electric range
- 10186145Creaking noise from fixed glass section of panoramic roof in area of rear passenger compartment grab handles
- 10184798Replace charge air hose between charge air cooler and turbocharger
- 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
- 10179904Implausible "service due" instrument cluster message, head unit pop-up, or Mmc message
Every Mercedes-Benz GLE 350 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.