2021 Mercedes-Benz GLE 350
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › GLE 350 › 2021
These records cover every 2021 Mercedes-Benz GLE 350. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
14 recalls name the 2021 Mercedes-Benz GLE 350. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2022 GLE 350 and 2021-2022 GLE 450 vehicles. The front acceleration sensor's wiring harness may be routed incorrectly, which can prevent the front air bags from deploying properly. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard 208, "Occupant…
Risk and remedy
Risk
An air bag that does not deploy properly can increase the risk of injury in the event of a crash.
Remedy
Dealers will inspect and reroute the wiring harness, as necessary, free of charge. Owner notification letters were mailed November 1, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2024100006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2024 GLE, GLS, C-Class, E-Class, S-Class, SL, GLC, CLS, AMG GT, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, causing a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 28, 2024. Owner notification letters will be mailed in phases, on February 23, 2024, April 19, 2024, June 28, 2024, August 9, 2024, October 1, 2024, and December 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 23V-445.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2022 GLE350 and GLE450 vehicles. A 12-Volt ground connection under the driver seat may not be secured properly, resulting in the ground connection overheating.
Risk and remedy
Risk
An overheated ground connection can increase the risk of a fire.
Remedy
Dealers will inspect and secure the 12-Volt ground connection as necessary, free of charge. Owner notification letters were mailed January 26, 2024. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2021 GLE350, GLE450, GLS450, GLS580, 2021 AMG GLE53, AMG GLE63, Maybach GLS600, AMG GLS63, and 2020 GLE580 vehicles. The air conditioner drain hoses may have been incorrectly installed, causing water to drain into the passenger compartment.
Risk and remedy
Risk
Water intrusion into the foot wells may cause corrosion and/or short circuits to electrical components, increasing the risk of fire. In addition, the emergency call (eCall) feature may be disabled and the doors may not unlock, increasing the risk of injury. Also, the engine may not start or may enter a limp-home mode, increasing the risk of a crash.
Remedy
Dealers will inspect and reinstall the air conditioner drain hoses, as necessary, free of charge. Owner notification letters were mailed April 28, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of recall numbers 21V-288 and 19V-587. MBUSA's numbers for this recall are 2023030014 and 15.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2022 GLE350, GLE450, 2022 AMG GLE53, AMG GLE63, and GLS450 vehicles. The steering coupling locking screw may loosen and possibly detach from the steering gear, resulting in a loss of steering control.
Risk and remedy
Risk
A loss of steering control can increase the risk of a crash.
Remedy
Dealers will replace the steering coupling locking screw, free of charge. Owner notification letters were mailed January 27, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022120016.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2022 GLE350, GLE450, GLS450, 2021-2022 AMG GLE53, 2020-2021 GLE580, GLS580, and 2021 GLE400e, AMG GLS63, AMG GLE63 S, and Maybach GLS600 vehicles. Due to a manufacturing error, the rear door window trim bars may detach.
Risk and remedy
Risk
Detached trim bars may cause a road hazard and increase the risk of a crash or injury.
Remedy
Dealers will inspect and secure the rear window trim bars, as necessary, free of charge. Owner notification letters were mailed November 1, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022090010.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2021 GLE 350, GLE 580, GLS 450, GLS 580, AMG GLE 53, AMG GLE 63 S, and AMG GLS 63 S vehicles. The rear window may be insufficiently bonded to the tailgate, which could allow the rear glass to detach.
Risk and remedy
Risk
Detached rear glass can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the rear window, free of charge. Owner notification letters were mailed December 8, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz LLC (MBUSA) is recalling certain 2018-2020 C300, 2019-2020 A220, AMG C43, AMG C63, 2020 GLE580, GLB250, 2020-2021 GLE450, GLE350, 2021 AMG GLE63, and AMG GLE53 vehicles. The LED headlights may have been incorrectly adjusted during a vehicle repair. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety…
Risk and remedy
Risk
Incorrectly adjusted headlights may reduce visibility, increasing the risk of a crash.
Remedy
Dealers will replace the LED headlights, free of charge. Interim letters notifying owners of the safety risk were mailed August 13, 2021. A second notice will be sent once the remedy is available. Owner notification letters were mailed January 2022. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2021 CLA-Class, GLE/GLS-Class, A-Class, E-Class, E-Class Coupe and Convertible, GLA/GLB-Class, GLC-Class, CLS-Class, and AMG GT-Class 4-door Coupe vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The MBUX multimedia system software may cause the display to remain…
Risk and remedy
Risk
A backup camera that displays a blank image reduces the driver's rear view, increasing the risk of a crash or injury.
Remedy
The multimedia system software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed beginning June 28, 2021. Owners may contact MBUSA customer service at 1-800-367-6373. MBUSA's number for this recall is 2021050012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2021 GLE450, GLE350, and 2020 GLS450, GLE580, GLS580 vehicles. During certain evasive driving maneuvers, the Electronic Stability Program (ESP) software may apply torque to one of the front wheels, pulling the vehicle to one side. As such, these vehicles fail to comply with the requirements of…
Risk and remedy
Risk
If the vehicle unexpectedly pulls to one side during an evasive maneuver, it can increase the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will update the ESP software, free of charge. The recall began March 31, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021030004.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz AG USA, LLC. (MBUSA) is recalling certain 2021 AMG GLE53, AMG GLE63, 2020 GLE580, 2020-2021 GLE350 and GLE450 vehicles with 5 passenger seating. While buckling the seat belt, the middle seat belt buckle could be pushed down into the gap below the seat cushion. If the buckle can't be retrieved, the buckle latch will be inoperable and unable…
Risk and remedy
Risk
An unrestrained occupant has an increased risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will secure the middle seat belt buckle, free of charge. The recall began December 18, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020110005.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2020 CLA250, CLA250 4MATIC and CLA35 AMG 4MATIC, 2020-2021 GLE350, GLE350 4MATIC, GLE450 4MATIC, GLS450 4MATIC and GLS580 4MATIC and 2021 GLE53 AMG Coupe, GLE63S AMG 4MATIC, GLS63 AMG 4MATIC and Maybach GLS600 4MATIC vehicles. The instrument cluster software may deactivate the illumination of certain…
Risk and remedy
Risk
If the interior switches are not illuminated, they may be more difficult to find and operate, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will update the instrument cluster software, free of charge. The recall began March 31, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020030019.
Owner complaints
48 complaints3 involved a crash2 involved a fire6 injuries
What owners report most
Latest complaints
- Forward collision avoidance › Automatic emergency braking · Lane departure › Blind spot detection · Unknown or other
While driving on the highway on three separate occasions the blind spot warning will pop up and show as inoperative, next the active break assist warning flashes as inoperative, and then the entire vehicle shows as inoperative and loses all acceleration and breaks down. This has happened three…
While driving on the highway on three separate occasions the blind spot warning will pop up and show as inoperative, next the active break assist warning flashes as inoperative, and then the entire vehicle shows as inoperative and loses all acceleration and breaks down. This has happened three times. Stayed over night at the dealership they “drove it for 70 miles” it didn’t happen to them. They released the truck back to me saying it was perfectly fine. A day later it happened again while on the highway. Highly unsafe!
- Engine
At approximately 87,000 miles, my 2021 GLE350 (M264 2.0T engine) experienced a severe engine misfire resulting in a flashing check engine light, rough idle, engine shaking, significant loss of power, and near-stall condition. The vehicle was taken to Speedhaus Automotive (Newbury Park, CA) where…
At approximately 87,000 miles, my 2021 GLE350 (M264 2.0T engine) experienced a severe engine misfire resulting in a flashing check engine light, rough idle, engine shaking, significant loss of power, and near-stall condition. The vehicle was taken to Speedhaus Automotive (Newbury Park, CA) where all four ignition coils and spark plugs were replaced. Total repair cost was approximately $635. This failure pattern is consistent with the documented M264 exhaust valve seat wear issue acknowledged by Mercedes-Benz technicians. A Mercedes dealer service report on an identical 2021 GLE350 explicitly states: "COMMON ISSUE FOR EXHAUST VALVE SEATS TO WEAR — KNOWN ISSUE WITH 260 AND 264 MOTORS." Mercedes-Benz has extended the warranty on the M260 engine (transverse variant) for this identical failure mode but has not extended it for the longitudinally-mounted M264 despite the same defect being present. Repair costs for full cylinder head failure on the M264 are being quoted at $6,000–$13,000. I am requesting NHTSA investigate whether a safety recall is warranted for the M264 engine across all affected GLE350, GLC300, C300, and E350 vehicles.
- Suspension
2021 mercedes-benz GLE 350 w. Aprox: 30,000 miles. Purchased the vehicle 3 years ago, when it had 17,000 miles on it. When driving at times the passenger rear shock will start making sqeaking / creaking noises. Been like this for almost 1 year now. I dont drive the vehicle very often, but when I do…
2021 mercedes-benz GLE 350 w. Aprox: 30,000 miles. Purchased the vehicle 3 years ago, when it had 17,000 miles on it. When driving at times the passenger rear shock will start making sqeaking / creaking noises. Been like this for almost 1 year now. I dont drive the vehicle very often, but when I do drive it it irritates me. The dealership said the shock needs to be replaced. There are no visible leaks, no abnormal ride quality, etc.
- Visibility › Defroster/defogger/hvac system
The contact owned a 2021 Mercedes-Benz GLE 350. The contact stated that warm air was blowing from the A/C unit while activated. The vehicle was taken to an independent mechanic, and the contact was informed that a leak had caused the A/C unit failure. The mechanic referred the contact to the dealer…
The contact owned a 2021 Mercedes-Benz GLE 350. The contact stated that warm air was blowing from the A/C unit while activated. The vehicle was taken to an independent mechanic, and the contact was informed that a leak had caused the A/C unit failure. The mechanic referred the contact to the dealer for assistance. The vehicle was taken to the dealer where a diagnostic test was performed. The contact was informed that the HVAC system was inoperable and an estimate for the repair was provided. The manufacturer was notified of the failure, and the contact was provided a case number. The manufacturer denied responsibility for the failure but offered a monetary credit towards the repair. The vehicle was not repaired. The contact later traded the vehicle due to the A/C unit failure. The failure mileage was approximately 66,000. The VIN was not available.
- Engine
While driving at night all error light showed up. I slowed down to the side of the road and while I was slowing down the engine died. I tried to start the car which worked but when I pressed the gas the engine died again. Tried it two more times with the same results. Then turned the car and waited…
While driving at night all error light showed up. I slowed down to the side of the road and while I was slowing down the engine died. I tried to start the car which worked but when I pressed the gas the engine died again. Tried it two more times with the same results. Then turned the car and waited a bit with the engine running. slowly started driving and was able to get home driving 20 mph. The next day took it to a shop that said that the battery was weak and they replaced the battery. Drove out of the shop and started hearing nosies from the engine. Immediately came back and was advised to take it to the dealer. Towed it to the dealer that checked it and said that they found metal in the oil filter and that I need to install a new engine. I read online and found many complains about the same engine issue with 2021 Mercedes GLE 350. Mercedes refuses to take responsibility that they built a faulty engine.
- Lane departure › Blind spot detection · Lane departure › Warning · Vehicle speed control
The vehicle has repeatedly experienced a sudden loss of acceleration, entering a reduced-power state while driving. Most recently, this occurred less than one week after I was advised that the issue had been fully resolved through a relay replacement. Critically, these incidents have occurred…
The vehicle has repeatedly experienced a sudden loss of acceleration, entering a reduced-power state while driving. Most recently, this occurred less than one week after I was advised that the issue had been fully resolved through a relay replacement. Critically, these incidents have occurred while my [XXX] child was in the vehicle, creating an unsafe and unacceptable situation. Below is a summary of the work that was done to resolve the safety concern. October: Drivetrain/Powertrain control unit internal fault Replacement of gateway/powertrain control module Wiring, grounding, and software inspections November: Active Brake Assist, ESP, and voltage supply faults Failure of both rear wheel speed sensors Replacement of left and right rear wheel speed sensors December: Dealership identified a faulty relay as the root cause Relay replaced and vehicle returned to service January, the vehicle again lost acceleration. And now, again in February. The same loss in acceleration incident. At this point, the vehicle has demonstrated a pattern of unresolved, safety-critical electrical failures. Given the repeated nature of the issue, the prior replacement of major components, and the involvement of braking and drivetrain systems, I no longer feel confident that additional part replacement without corporate oversight will result in a safe or permanent resolution. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Engine
This is regarding a 2021 gle 350. The car was parked overnight and in the morning was unable to start or crank . I had to tow the vehicle to the service center that has maintained the car since purchased date and they told Me there’s a problem with the engine and I will need a new engine costing…
This is regarding a 2021 gle 350. The car was parked overnight and in the morning was unable to start or crank . I had to tow the vehicle to the service center that has maintained the car since purchased date and they told Me there’s a problem with the engine and I will need a new engine costing $28,000 dollars., the car has 42,000 miles and has an impeccable service history with Mercedes Benz. They did not tell me any specific engine part that’s faulty. There was no warning lights, check engine lights. Had I been driving this car and it happened it could have been catastrophic.
- Engine
There is a known issue with the Cylinder Heads on specific models of Mercedes vehicles. Symptoms of M264 Cylinder Head Failure If your GLE 350 is experiencing these symptoms, it may be covered under the extension: Check Engine Light (MIL): Often triggered by misfire codes. Rough Idle: Noticeable…
There is a known issue with the Cylinder Heads on specific models of Mercedes vehicles. Symptoms of M264 Cylinder Head Failure If your GLE 350 is experiencing these symptoms, it may be covered under the extension: Check Engine Light (MIL): Often triggered by misfire codes. Rough Idle: Noticeable shaking or uneven idling when stopped. Loss of Power: Potential stalling or significant power reduction during acceleration. Low Compression: Diagnostic tests often reveal low pressure in one or more cylinders. This is not being addressed my Mercedes USA where Mercedes Canada has offered an extended warranty. Using social media I have comprised a list of over a hundred impacted owners. Many more exist. What this does is cost catastrophic failure of the engine leaving the driver stranded in whatever lanes they were traveling in. I am disabled and for me this created a life threatening situation. When reaching out to MBUSA the answer is simply "not warranty exists" where MB Canada has extended the warranty to an additional 15k miles from notice. My engine blew. The replacement cost is near $20,000 dollars. The mileage on my engine was 65k. Many others are impacted and a class action lawsuit is the only other course of action it seems. Regards, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Structure › Body · Unknown or other
Sunroof makes loud, high pitched noise when it’s windy or driving high speeds. Sunroof complaints found online for bad seals or components of sunroof being bad or unaligned. Sounds could cause driver not to hear other safety issues with vehicle as well as leaking if water.
- Unknown or other
My vehicle suddenly started shaking and losing power, the check engine light came on and the problem continues to vibrate when idling, it will not shift into gear to go. Very unnerving and unsafe as it happened in a intersection. Sometimes it drives fine and then vibrates and goes into low gear and…
My vehicle suddenly started shaking and losing power, the check engine light came on and the problem continues to vibrate when idling, it will not shift into gear to go. Very unnerving and unsafe as it happened in a intersection. Sometimes it drives fine and then vibrates and goes into low gear and loses power. I took to a certified Mercedes dealer and they changed the spark plugs and 4 coils as well - After 4 weeks, I am told the CYLINDER HEAD needs to be replaced. It has 68k miles. The mechanic has already had 2 other 2021 GLE 350 with exactly the same issue. There are several similar cases discussed online as well.
- Engine · Power train · Unknown or other
Original owner of a 2021 GLE, purchased on April 21, 2021. The vehicle is currently 4 years and 6 months and 22 days old with approximately 49,000 miles. Despite meticulous adherence to all scheduled maintenance performed and no warning lights activated the vehicle suddenly shutdown and would not…
Original owner of a 2021 GLE, purchased on April 21, 2021. The vehicle is currently 4 years and 6 months and 22 days old with approximately 49,000 miles. Despite meticulous adherence to all scheduled maintenance performed and no warning lights activated the vehicle suddenly shutdown and would not restart. According to MB maintenance department it suffered a catastrophic and complete engine failure. This type of premature and total engine failure in a properly maintained, low-mileage vehicle is clearly a defect in material or workmanship. This is a serious safety defect that rendered the vehicle completely inoperable with no warning. Issues are resulting from valve guide wear issues, camshaft codes, valve openness, and no-compression symptoms, camshaft, timing chain, etc.
- Engine
we own a Mercedes-Benz GLE 350 model 2021. Our vehicles engine has stopped running on two different occasions, resulting in a very scary near miss accident situation. The first time this happened was it 22,000 miles, the engine shut off as a result of a failure in the engine cylinder head valve…
we own a Mercedes-Benz GLE 350 model 2021. Our vehicles engine has stopped running on two different occasions, resulting in a very scary near miss accident situation. The first time this happened was it 22,000 miles, the engine shut off as a result of a failure in the engine cylinder head valve that burned up, causing the car to shut off in the middle of an intersection. The second incident happened at 56,000 miles where the vehicles engine shut off. This was also in the middle of an intersection, this time turning left in front of traffic. The reason why the engine turned off was because the lower part of the engine lost a rod bearing.this is what the dealership told us which cause the engine to have low compression and turn off. In both incidences, the check engine light did not come on. There was no warning. There are several people that have exactly the same problem with their vehicle and have also had the same two situations with two separate repairs made to their cars. People online are calling these Covid engines because the materials that were used to build the engines were made during Covid and they have defects. The GLA 350 model year 2021 appears to be the only year the GLE 350’s are having these issues. Mercedes-Benz refuses to acknowledge any of these issues and is not willing to help properly fix the engines. The only way to properly fix the engine is to completely replace it because it is full of defective parts and after the engine has failed the engines cannot be repaired.. This leaves us with no alternative to try and repair the vehicle ourselves so we are 100% relying on Mercedes to do the right thing and fix the problems that they caused to this 2021 model year GLE 350.
- Engine
The contact owns a 2021 Mercedes-Benz GLE350. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the cylinder head. The vehicle was repaired. The manufacturer was notified of…
The contact owns a 2021 Mercedes-Benz GLE350. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the cylinder head. The vehicle was repaired. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 74,000.
- Visibility › Sun/moon roof assembly
The contact owns a 2021 Mercedes-Benz GLE350. The contact stated that the floor mats were wet after it had rained, and mold had formed on the floor mats. The rear hatch door occasionally unlocked unintendedly, and the radio would change stations independently. The contact stated that other…
The contact owns a 2021 Mercedes-Benz GLE350. The contact stated that the floor mats were wet after it had rained, and mold had formed on the floor mats. The rear hatch door occasionally unlocked unintendedly, and the radio would change stations independently. The contact stated that other electrical malfunctions occurred suddenly and intermittently. The vehicle was taken to the dealer, and the contact was informed that the sunroof drains were clogged and caused the water to build up, which then caused the electrical shortages inside the vehicle. The contact learned that the failure occurred due to the ends of the drainage system for the sunroof being tapered. The vehicle was not repaired. The manufacturer was informed of the failure, and a case was opened. The failure mileage was approximately 49,200. The VIN was unavailable.
- Engine and engine cooling
The contact owns a 2021 Mercedes-Benz GLE350. The contact stated that while driving 65-70 MPH, the vehicle was skipping. The contact immediately veered towards an exit ramp. The contact noticed knocking sounds coming from the engine, and the vehicle stalled on the exit ramp. There was smoke coming…
The contact owns a 2021 Mercedes-Benz GLE350. The contact stated that while driving 65-70 MPH, the vehicle was skipping. The contact immediately veered towards an exit ramp. The contact noticed knocking sounds coming from the engine, and the vehicle stalled on the exit ramp. There was smoke coming from underneath the hood. The vehicle failed to restart and was towed to the dealer, where it was diagnosed that the engine had imploded and sustained a hole. The dealer determined that the engine needed to be replaced. Additionally, the dealer took the engine apart and informed the contact that the cause of the engine implosion could not be determined even with the assistance of the engineers. The vehicle was not repaired due to the cost. The contact then brought an independent mechanic to the dealer to inspect the vehicle. The mechanic inspected the engine and informed the contact that the failure had occurred due to a lack of engine oil; however, the contact stated that the dealer had performed an oil change on the vehicle 27 days prior to the failure. The manufacturer was notified of the failure but denied assistance in covering the repair. The manufacturer informed the contact that the engineers had not yet determined the cause of the engine implosion. The failure mileage was 69,100.
- Back over prevention · Electrical system
The contact owns a 2021 Mercedes-Benz GLE350. The contact stated that while reversing, the back over prevention camera screen was black and there was no image displayed, causing a visibility hazard for the driver. The vehicle was taken to the local dealer, who indicated that the VIN was not…
The contact owns a 2021 Mercedes-Benz GLE350. The contact stated that while reversing, the back over prevention camera screen was black and there was no image displayed, causing a visibility hazard for the driver. The vehicle was taken to the local dealer, who indicated that the VIN was not included in NHTSA Campaign Number: 21V354000 (BACK OVER PREVENTION, ELECTRICAL SYSTEM). The contact stated that the vehicle had experienced the failure listed in the recall. The vehicle was not repaired. The failure mileage was 29,000.
- Power train
Location: Dallas, TX – Woodall Rodgers Freeway near North Hall Street exit Mercedes-Benz USA Case #: 18469650 What component or system failed or malfunctioned, and is it available for inspection upon request? The vehicle’s 48-volt electrical architecture appears to have failed, specifically the…
Location: Dallas, TX – Woodall Rodgers Freeway near North Hall Street exit Mercedes-Benz USA Case #: 18469650 What component or system failed or malfunctioned, and is it available for inspection upon request? The vehicle’s 48-volt electrical architecture appears to have failed, specifically the DC/DC converter or Integrated Starter-Generator (ISG) that provides 12-volt power to all control modules. When this component failed, it caused a total loss of propulsion and electrical power. The vehicle is currently at a Mercedes-Benz dealership in Dallas and available for inspection upon request by NHTSA or Mercedes-Benz USA (case #18469650). How was your safety or the safety of others put at risk? While driving approximately 50 mph on the Woodall Rodgers Freeway with my family in the car, the vehicle suddenly lost all engine power and throttle response without warning. The accelerator stopped responding, and the engine stalled completely within seconds. I was able to coast partially onto an exit ramp, but once stopped, the car would not restart and could not be shifted into Neutral. We were stranded in live traffic with limited steering assist and no way to move the vehicle, placing my family and other motorists at serious risk of collision. Has the problem been reproduced or confirmed by a dealer or independent service center? The vehicle is currently at a Mercedes-Benz authorized dealer, and the failure has been logged with Mercedes-Benz USA under case #18469650. Initial findings point to a malfunction of the DC/DC converter or 48-volt system. Full STAR diagnostic data and fault codes are pending. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives, or others? Mercedes-Benz USA has been notified and opened case #18469650. The vehicle has been inspected by the dealership’s certified technicians and is awaiting official diagnostic reporting and possible engineering review through Mercedes’ Technical Assistance
- Electrical system · Engine
Not sure vehicle was parked and caught on fire from the drivers side completely burning
- Engine
I am writing to document a recurring and serious issue with the Mercedes-Benz GLE equipped with the M264 engine, specifically relating to premature cylinder head failure. In my case, the vehicle began showing the following symptoms: Rough engine idle and noticeable vibration during startup Loss of…
I am writing to document a recurring and serious issue with the Mercedes-Benz GLE equipped with the M264 engine, specifically relating to premature cylinder head failure. In my case, the vehicle began showing the following symptoms: Rough engine idle and noticeable vibration during startup Loss of power, especially when accelerating Check engine light with fault codes related to misfire or combustion issues Oil and/or coolant loss, with no external leaks Engine knocking or ticking noises near the top end of the engine After a professional inspection and diagnostic testing, I was informed that the issue is likely due to a defect or failure in the cylinder head, possibly involving warping, cracking, or failure of the valve seats or head gasket area. Upon further research, I discovered that this issue is not isolated. Multiple owners of vehicles with the M264 engine—including various GLE, C-Class, and E-Class models—have reported similar problems, often occurring well before 70,000 miles and despite regular maintenance. The pattern suggests a possible design flaw or quality issue with the engine’s cylinder head. As of now, it appears no formal recall or technical bulletin has been issued by Mercedes-Benz regarding this specific problem. However, the number of similar reports suggests the issue is widespread enough to merit formal investigation or at least acknowledgment by the manufacturer.
- Fuel/propulsion system
The car has stalled 4 or 5 times, while driving in traffic. This can obviously be life threatening. The check engine light came on yesterday. We recently brought the car to Mercedes Benz in Daytona Beach, Florida. They told us we had low pressure in the cylinders, and needed a new cylinder head for…
The car has stalled 4 or 5 times, while driving in traffic. This can obviously be life threatening. The check engine light came on yesterday. We recently brought the car to Mercedes Benz in Daytona Beach, Florida. They told us we had low pressure in the cylinders, and needed a new cylinder head for $10,000. The cylinder pressures on their test however were all normal. They never mentioned a recall for a fuel pump defect causing cars to stall. A local independent repair company confirmed the cylinder pressure test was normal. Mercedes recalled 324,000 vehicles for this defective fuel pump between 2012 and 2020 (abc news). They recalled over 143,000 vehicles from June 2021 to 2023. My model, GLE350, was included in both recalls. I called Mercedes customer service. They said my car was built in February 2021, and there is no recall for this vehicle. There have been recalls for defective fuel pumps from 2012 to 2020, and June 2021 to 2023. I strongly suspect my vehicle built in February 2021 has the same defective fuel pump. I will bring the vehicle to an independent well qualified service center. If they diagnose a fuel pump problem. I would like Mercedes to reimburse me for the repair.
- Power train
Replacement of Cylinder Head (#1)
- Engine
On May 26, 2025, around 3:00 PM, I was traveling with my family on a bright and sunny day, with no rain for several days leaving the roads dry. As we were on I-35, I took an exit, and just a few seconds later, my 2021 Mercedes-Benz GLE 350 unexpectedly shut off, all the lights on the the dashboard…
On May 26, 2025, around 3:00 PM, I was traveling with my family on a bright and sunny day, with no rain for several days leaving the roads dry. As we were on I-35, I took an exit, and just a few seconds later, my 2021 Mercedes-Benz GLE 350 unexpectedly shut off, all the lights on the the dashboard lit up, and the vehicle came to a sudden and complete stop. Thankfully, this incident occurred on the service road rather than the highway, and we were at low speed otherwise it could have posed a serious risk to my family and me. Once the car stalled, both the steering and tires locked up. However the vehicle had power but would not start or move. As the same situation could happen to someone else which could put them at serious risk it might be in the best interest of Mercedes-Benz to research and fix this issue. I reached out for a tow truck, and the driver had to hook it up and drag my vehicle onto the flatbed. Mercedes-Benz service suggested a replacement of the engine and could not diagnose what the issue is. I have consistently performed the recommended maintenance on my vehicle since I purchased it, and it currently has around 63,000 miles.
- Electrical system · Engine · Power train
While driving at about 55mph on road with one lane going each way, the car engine shut off, all instrument displays went off. There was no check engine light, warning or noise. I was almost rear ended by a car behind me. The car behind me swerved barely missing me, but almost hit oncoming traffic.…
While driving at about 55mph on road with one lane going each way, the car engine shut off, all instrument displays went off. There was no check engine light, warning or noise. I was almost rear ended by a car behind me. The car behind me swerved barely missing me, but almost hit oncoming traffic. Once car was on side of road it would not start. I tried to jump car battery with NOCO jump starter and it did not work. Instrument display did not come on, car transmission stuck in Drive. After testing battery with digital voltmeter it showed 12.6V, but car would still not come on nor would instrument display. Car had to get towed to dealer where it's currently at being diagnosed. This was very dangerous and could have been fatal.
- Visibility
The contact owns a 2021 Mercedes-Benz GLE350. The contact stated that while the vehicle was parked, there was condensation leaking from a hole near the trunk release button onto the pedal and the floor of the front passenger’s side of the vehicle. The vehicle was not diagnosed or repaired. The…
The contact owns a 2021 Mercedes-Benz GLE350. The contact stated that while the vehicle was parked, there was condensation leaking from a hole near the trunk release button onto the pedal and the floor of the front passenger’s side of the vehicle. The vehicle was not diagnosed or repaired. The contact believed that the failure was associated with NHTSA Campaign Number: 23V177000 (Visibility). The vehicle was not diagnosed of repaired. The manufacturer was notified of the failure. The failure mileage was 57,432.
- Engine
My Mercedes gle350 2021 is having a cylinder misfire. I had the repairs done last February. Carlton Mercedes acknowledged this is a known issue with this car. Did some googling and saw how big of an issue this is in this car. Repairs were made and now a year later cylinder misfire again! My…
My Mercedes gle350 2021 is having a cylinder misfire. I had the repairs done last February. Carlton Mercedes acknowledged this is a known issue with this car. Did some googling and saw how big of an issue this is in this car. Repairs were made and now a year later cylinder misfire again! My neighbor has the same car but 2022 having the same issue currently. This needs to be recalled. Mercedes needs to be held accountable for this issue. It’s costing people anywhere from 7-15,000 dollars to repair and most of these cars only have around 50,000 miles on them! It’s insane!!
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11010450Complaint When using the offroad display in the MBUX, the "Transparent hood" function cannot be activated using the camera symbol. Cause MBUX FUP5 software: E504.3 (A 297 904 97 00) E504.4 (A 297 904 03 01) Remedy Update of head unit A26/17 to the new software: E504.5 (A 297 904 09 01)
- 11010438Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 01.06.2023 (Send to Body/Chassis/Entertainment Inbox) - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 01.06.2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11010437Complaint Automatic window raising function of side window inoperative. Cause Denormalization of the window lifter system. Remedy Update the software in the affected door control unit (N69/x). This requires the door control unit (N69/x) to be commissioned. (Path: XENTRY -> Control units view -> DCU-XX (N69/x) -> Adaptations -> Commissioning) SW item numbers of the repair software: A1679023716 for the door control units on the front doors (N69/1 and N69/2) A1679023816 for the door control units on the rear doors (N69/3 and N69/4)
- 11010435Complaint -Check engine light(MIL) is ON. -Current and stored fault code in DCCU and PTCU : P2E9873 The position sensor of the exterior socket flap of the vehicle socket (direct current) has an electrical fault. The actuator does not open. -Starting the vehicle or Charging the vehicle is normal without any issues. Cause Software in the "N116/5 - Direct current charge connection unit (DCCU)" control unit. Remedy SW remedy for N116/5(DC-Charging control unit box) is in progress. Once the software is available, update the software for N116/5 and perform SCN coding of N116/5 For this issue, the vehicle starting or charging functions are not typically affected. Do not replace any parts. Replacing parts will not bring a solution for this issue.
- 11009550Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : Remedy 1 (Only applies to vehicles produced during or prior to June 2023) 1. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 2. Clear picture of VIN on B-pillar. 3. Ensure that the rest of the AC system has been thoroughly checked for leaks before condemning the evaporator. Remedy 2 (Applies to all 167's produced after June 2023) 1. Do NOT remove the expansion valve from the evaporator prior to being advised to in a TIPS case. 2. Initial Quick Test 3. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 4. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 5. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 6. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 7. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 8. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 9. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments.
- 11009549Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 6/1/2023 - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 6/1/2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11009036Complaint "Active Emergency Stop Assist Currently Unavailable" and "Active Steering Assist Inoperative" instrument cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.
- 11008882Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : Remedy 1 (Only applies to vehicles produced during or prior to June 2023) 1. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 2. Clear picture of VIN on B-pillar. 3. Ensure that the rest of the AC system has been thoroughly checked for leaks before condemning the evaporator. Remedy 2 (Applies to all 167's produced after June 2023) 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. Please see the list of WIS documents for forming gas leak check and recharging of the system. All documents, with the exception of videos need to be uploaded for the warranty claim. Videos are only needed if a TIPS case is opened. Ensure that a full vacuum is pulled on the system for at least 30 minutes after replacement Condenser replacement is NOT authorized as a suitable repair in lieu of the dryer not being available.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008093Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008072Complaint White plastic insert present on microphone assembly. See figure A for example. Cause The insert (breathable filter) is designed to be inside for dust protection and air flow control. Remedy Do not remove the breathable filter from the microphone assembly. This part is designed to be in the microphone and should remain in the vehicle. Note: If TIPS support is required for microphone symptoms please open a TIPS case and reference this LI.
- 11008056Complaint Check engine light on. Fault code P207273 - "Throttle actuator valve is blocked due to ice" stored. Engine may crank and not start. Fault code P210185 may also be stored. Cause Moisture freezing on throttle actuator during extreme low ambient temperatures. Remedy Update software of engine control module. Software increases throttle valve flapping after engine turned off to prevent moisture buildup.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007972Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation.
- 11007969Complaint When using the offroad display in the MBUX, the "Transparent hood" function cannot be activated using the camera symbol. Cause MBUX FUP5 software: E504.3 (A 297 904 97 00) E504.4 (A 297 904 03 01) Remedy The remedy is currently being developed.
- 11007956Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2020-2023 CLS (257 platform), E-Class (213 and 238 platform), GLE (167 platform), and AMG GT 4-Door (290 platform) vehicles, the engine control unit software does not correspond to current production specifications. As a consequence, the functionality of the post-catalyst oxygen sensor may be impaired due to increased thermal loading. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software.
- 11007858Complaint The "Easy entry and exit feature" function deactivates itself after a brief period. Cause The cause is currently being investigated. Remedy A remedy is currently not available. A software update in the seat control unit does not solve the problem. The document will be updated once the reason has been analyzed and a remedy is available.
- 11007857Complaint Customer concern of Air Conditioning not cooling. Note: For vehicles produced during or prior to June 2023, a TIPS case is not necessary. However, parts from repairs on such vehicles may be requested back for analysis at the QEC. Therefore, please follow parts disposition in NetStar. Repairs where parts are not returned per parts disposition instructions, or parts found to be NTF (no trouble found) are subject to debit. ALL steps, with the exception of videos, should be documented and uploaded with the claim submission. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. "NO TIPS case needed on vehicles during or prior to June 2023"
- 11007796Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11007673Complaint Damage or discoloration to paint protection films on vehicle. Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.
- 11006700Complaint Once the head unit A26/17 is updated to the FUP4 software release E445.0, it may be the case that online connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.
- 11006695Complaint When using the offroad display in the MBUX, the "Transparent hood" function cannot be activated using the camera symbol. Cause MBUX FUP5 software: E504.3 (A 297 904 97 00) E504.4 (A 297 904 03 01) Remedy The remedy is currently being developed. Note: A remedy is not yet available. Replacing the hardware does not resolve the symptom. Do not replace the MBUX for this concern. The information will be updated accordingly as soon as a remedy is available.
- 11006678Complaint Head-up display permanently or sporadically unavailable - with warning message in driver display Head-up display permanently or sporadically unavailable - without warning message in driver display Display permanently or sporadically discolored and out of focus Cause Previous N133/1 - Instrument cluster (IC) control unit software. Remedy Update the N133/1 - Instrument cluster (IC) software.
- 11006550Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. If the vehicle is produced AFTER June 2023, a TIPS case is required for replacement. Please open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. 9. For vehicles produced during or prior to June 2023, a TIPS is not necessary. However, parts from repairs on such vehicles may be requested back for analysis at the QEC. Therefore, please follow parts disposition in NetStar. Repairs where parts are not returned per parts disposition instructions, or parts found to be NTF (no trouble found) are subject to debit. NOTE: Please see the list of WIS documents for forming gas leak check and recharging of the system. All documents, with the exception of videos need to be uploaded for the warranty claim. Videos are only needed if a TIPS case is opened. Ensure that a full vacuum is pulled on the system for at least 30 minutes after replacement Condenser replacement is NOT authorized as a suitable repair in lieu of the dryer not being available.
- 11005347Complaint Yellow coolant warning system message appears in instrument cluster. Fault code P048392 or P048397 present in N127 Powertrain Control Unit. Cause Faulty communication between fan and control unit N127-PTCU. Remedy If other fault codes related to engine fan are present, process these first. Replace engine fan with part as specified in XENTRY parts information. Group 50/015. Note: Do not install a lower wattage fan than what was originally installed in vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005334Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.
- 11005313Complaint Check engine light on and fault code P019185 current or stored in MED41 control unit. Adaptation and misfire faults may also be stored. Vehicle may enter limp home mode. Cause False detection of rail pressure sensor out of range. Remedy Update software of engine control module N3/10. Reset mixture adaptation and clear fault codes.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11003211Complaint The following event codes are logged in control unit IDC213 - N62/4 (Intelligent Drive control unit): U0401FC and U0401FD. Cause Under analysis. Remedy Neither of the two event codes is relevant for the functioning of control unit IDC213 - N62/4 (Intelligent Drive control unit) and can be ignored.
Every Mercedes-Benz GLE 350 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.