2006 Nissan Armada
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Nissan › Armada › 2006
These records cover every 2006 Nissan Armada. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 2006 Nissan Armada. Newest first.
Nissan IS recalling certain model year 2004-2006 armada, titan, infiniti QX56 and model year 2005-2006 frontier, pathfinder and xterra vehicles. the intelligent power distribution module (ipdm) assembly contains an engine control module (ecm) relay that has a diode for electrical current noise reduction. The ecm relay may allow silicon vapor to form and…
Risk and remedy
Risk
This could cause engine stalling increasing the risk of a crash.
Remedy
Dealers will replace the ecm relay inside the ipdm assembly. This service will be performed free of charge. the safety recall began on december 6, 2010. owners may contact nissan at 1-800-647-7261.
Nissan IS recalling certain front and rear lower links, p/nos. 54501Zq00a, 54500zq00a, 551a1zq00a, 551a0zq00a , 54501ea00a, 54500ea00a, 551a1ea500, 551a0ea500, 54501zr00a, and 54500zr00a, sold between november 25, 2009 and may 14, 2010 as replacement parts for model year 2004 through 2010 titan, armada, and QX56, and model years 2005 through 2010 frontier…
Risk and remedy
Risk
If the collar weld separates, the vehicle handling will deteriorate, possibly resulting in a vehicle crash.
Remedy
Nissan will notify owners and dealers will replace any affected lower link free of charge. the safety recall began on july 12, 2010. owners may contact nissan at 1-800-647-7261.
Nissan IS recalling certain model year 2005-2009 titan, armada, and infiniti QX56 vehicles. the instrument panel fuel gauge may inaccurately display that the vehicle still has some fuel, typically about one quarter tank, when the fuel tank IS empty.
Risk and remedy
Risk
This could cause the vehicle to run out of gas and stall on the highway, which could cause a crash.
Remedy
Dealers will replace the fuel sender unit inside the fuel tank with a new improved sender card. this service will be performed free of charge. the safety recall began on march 22, 2010. owners may contact nissan at 1-800-647-7261.
Nissan IS recalling 180,664 my 2005-2006 titan, armada and infinity QX56 vehicles manufactured after march 17, 2005, that are equipped with a visteon air conditioning condenser fan motor. The fan motor may not be properly sealed allowing excessive water intrusion and inadequate drainage of moisture.
Risk and remedy
Risk
This could cause corrosion in the motor leading possibly to overheating and a fire.
Remedy
Dealers will install a 'thermal protector kit' and test the air conditioning condenser fan motor and replace it if necessary. the recall began on august 2, 2008. owners may contact nissan at 1-800-647-7261.
Certain hopkins aftermarket trailer brake control connection harnesses sold for use on certain models of nissan vehicles which are listed above. the internal part numbers within hopkins are: 1010476025, 1040376025, 1110476025, 1170376025, 1290376025, 1010476035, 1040376035, 1110476035, 1170376035, and 1290376035. a wire may have been placed in an…
Risk and remedy
Risk
This harness would result in power from the trailer brake controller going to the towing vehicle dash light circuit rather than the trailer brakes. this result would be the lack of trailer braking when the towing vehicle brakes were applied. it would also result in the towing vehicles dash lights being activated when the vehicle brakes were applied. the failure of the application of the trailer brake could result in reduced ability to stop and contribute to a possible crash.
Remedy
Hopkins will notify owners and replace the original harness with a revised harness free of charge. the recall began august 17, 2007. owners can contact hopkins at 800-835-0129.
Owner complaints
266 complaints14 involved a crash13 involved a fire12 injuries
What owners report most
Latest complaints
- Forward collision avoidance › Automatic emergency braking · Service brakes · Suspension
Breaks suddenly went out and I couldn't stop. I had our kids in the car.
- Service brakes
Earlier in the year the brake light (some times with slip and ABS) came on the dash and suddenly braking was diminished. There was a horrid grinding sound plus vibration under the pedal. I was on highway 17 (a dangerous mountain freeway in CA) going downhill and it was extremely scary as has a…
Earlier in the year the brake light (some times with slip and ABS) came on the dash and suddenly braking was diminished. There was a horrid grinding sound plus vibration under the pedal. I was on highway 17 (a dangerous mountain freeway in CA) going downhill and it was extremely scary as has a car full of friends kids and hardly any brakes. I braked as much as it would allow, down shifted and pulled to the side (which again if you google that highway people die all the time from idiot drivers/speeders/tight corners). I instinctively turned off the car and got out to check off something had gotten caught in my wheel but nothing. I turned the car on and the problem had gone so drove to the nearest garage but he couldn't find anything wrong. I called Nissan but they said they knew of no problems with breaking systems on the Armada and said to bring it in and pay for an expensive diagnosis. When I got home I googled it and found 100s of similar experiences with all sorts of repairs at Nissan that hadn't worked. Some say brake booster, others sensor, other reset or upgrade hardware. Not one actually fix so far but I did find a couple of lawsuits for the same reason so don't understand how this is not a recall. The second time I was in town so it wasn't too bad but hard to stop at the crossing for a pedestrian and today it went again going back up the mountain but luckily don't need to brake much going in that direction. If it can't be fixed and it involves brakes then surely this is a serious safety violation. I also noticed that others are having a similar problem with newer Armadas with a newly upgraded braking system from Nissan and another lawsuit is on file. How is this being ignored? My car is 20 and I was looking into another Nissan but if they don't stand by and honor their mistakes then I really have no faith in them
- Service brakes
Once in awhile when the brakes are applied there is a loud sound that sounds like ache large can being crushed, and the brakes don't work properly. The car sort of lurches to a stop rather than coming to a smooth stop. If the engine is shut off and turned back on nine times out of 10 the brakes…
Once in awhile when the brakes are applied there is a loud sound that sounds like ache large can being crushed, and the brakes don't work properly. The car sort of lurches to a stop rather than coming to a smooth stop. If the engine is shut off and turned back on nine times out of 10 the brakes will begin to work again but occasionally it takes a few times of restarting the vehicle. I contacted Nissan and they said that they would contact me back and they had a lawyer call me who really just wanted to interrogate me more than offer any kind of solutions or answers. I was able to look up online and see that there is or was a class action lawsuit and that it's a known problem with many Nissan armadas being the master solenoid. This seems to be a continuing safety issue and if someone were to have to come to a quick stop there's no warning that this is going to happen beforehand and would negate any kind of safety stop. This has been going on for many years and is extremely expensive to fix. Which puts it right out for most families to be able to afford fixing this and just having to lope along hoping that it isn't one of those times when the brakes are going to give out in an emergency. Given that Nissan contacted me with a lawyer shows me that they are afraid of what could happen but not yet concerned enough that enough people have died for it to be worth their while cost-wise.
- Air bags · Service brakes · Structure › Body
Brakes. Went out with no warning For second time
- Service brakes, hydraulic
The contact owns a 2006 Nissan Armada. The contact stated while driving at an undisclosed speed and attempting to slow the vehicle, the contact heard an abnormal sound emanating from the brake pads, requiring increased effort to slow the vehicle. The vehicle returned to normal functionality, but…
The contact owns a 2006 Nissan Armada. The contact stated while driving at an undisclosed speed and attempting to slow the vehicle, the contact heard an abnormal sound emanating from the brake pads, requiring increased effort to slow the vehicle. The vehicle returned to normal functionality, but the failure became a regular occurrence. The ABS warning light was illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was unknown.
- Electrical system
The contact owed a 2006 Nissan Armada. The contact stated that while driving at an undisclosed speed, the contact noticed fire and smoke coming from the front passenger side underneath the glove compartment area. The contact stopped and parked the vehicle. The contact exited the vehicle and noticed…
The contact owed a 2006 Nissan Armada. The contact stated that while driving at an undisclosed speed, the contact noticed fire and smoke coming from the front passenger side underneath the glove compartment area. The contact stopped and parked the vehicle. The contact exited the vehicle and noticed the vehicle was on fire. The fire department arrived on the scene and extinguished the fire. A fire report was filed. There were no injuries sustained. The vehicle was left on the shoulder of the road. The contact stated the local police authorities later placed a sticker on the disabled burned vehicle because it was left on the shoulder of the road and had to be removed. The contact stated that the vehicle was junked. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 200,100.
- Service brakes
While driving the brake light came on and when I attempted to stop pedal goes almost to the floor and loud grinding noise is heard. I was able to barely stop the vehicle, I then shut off the vehicle, checked around the vehicle as well as engine compartment not finding any noticeable issue.…
While driving the brake light came on and when I attempted to stop pedal goes almost to the floor and loud grinding noise is heard. I was able to barely stop the vehicle, I then shut off the vehicle, checked around the vehicle as well as engine compartment not finding any noticeable issue. Restarted the vehicle and brake light was off able to stop with no issue and no grinding noise was heard. Mentioned this to dealer when it was brought in for oil change and they indicated that there was no notice of a recall for this issue. They checked the vehicle and could not find any issues. This has happened several more times where brake light goes on, issue with trying to stop and loud grinding noise. The remedy seems to be to get the vehicle stopped, barely, shut off the vehicle, wait for a short moment and then restart the vehicle. This is very concerning if this happens when needing to make an immediate stop as it takes a bit to get the vehicle to stop when this occurs. Nothing in particular is being done while driving to cause this to happen and I have not been able to replicate.
- Service brakes
Several times when driving, my brake light will come on and when pressing the brake, it does not engage. When you press on the pedal you hear a loud grinding sound. It does not slow down the vehicle at all and the grinding is loud and seems to be damaging internal parts. When you turn the engine…
Several times when driving, my brake light will come on and when pressing the brake, it does not engage. When you press on the pedal you hear a loud grinding sound. It does not slow down the vehicle at all and the grinding is loud and seems to be damaging internal parts. When you turn the engine off, and restart it the problem goes away. I have read so many similar issues with 2006 nissan armada about the brake light. How is this not a safety recall especially when I’m on the freeway driving 65 MPH and all of a sudden brake light comes on! I have to pull over safely and hard to do especially when the brake does not engage at all when the light is on. This is a huge safety concern for me due to the fact that I never know when this is going to happen again. What if it happens while I need to come to a quick emergency stop?! This is a major safety concern that needs to be looked into!!
- Service brakes
I was driving on the road and my brake light came on and my brakes failed. As I tried to stop my brakes made a grinding spring noise. I turned the car off and after about 3 minutes I restarted and everything was fine. I continue to drive and less than 10 minutes later it did it again. I have went…
I was driving on the road and my brake light came on and my brakes failed. As I tried to stop my brakes made a grinding spring noise. I turned the car off and after about 3 minutes I restarted and everything was fine. I continue to drive and less than 10 minutes later it did it again. I have went online to look for information and I see that there was a lawsuit about the booster Delta sensor. I called Nissan and they denied this, and I went to the Nissan dealership and they will check it out because they have not seen any recalls on my vehicle for this problem yet online there's a whole lot of customer complaints about this model doing the exact same thing. Here is the Case# 46966578 Nissan gave me to document the call. https://www.google.com/url?sa=t&source=web&rct=j&url=https://m.carcomplaints.com/news/2014/nissan-delta-stroke-sensor-brake-lawsuit.shtml&ved=2ahUKEwiW_sjo1rn5AhXiIEQIHVLABjMQFnoECBsQAQ&usg=AOvVaw2DxxR2-Vd0tjpN2-V2JVBq
- Air bags · Power train · Service brakes
The airbag light has been on for a while indicating that there is a defect in the airbags . The brakes light comes on randomly and the car brakes on its own without me applying the brakes and that is very dangerous especially on the highway and the transmission light comes on showing the 4x4 light as on for no reason and I would have it on just the 2 wheels
- Engine and engine cooling · Equipment
The contact owned a 2006 Nissan Armada. The contact stated while driving approximately 20 MPH and approaching a stop sign, the contact became aware of smoke and then fire coming from underneath the hood. There was no warning light illuminated. The contact and passenger exited the vehicle safely.…
The contact owned a 2006 Nissan Armada. The contact stated while driving approximately 20 MPH and approaching a stop sign, the contact became aware of smoke and then fire coming from underneath the hood. There was no warning light illuminated. The contact and passenger exited the vehicle safely. The contact stated that she had minor hip pain but did not seek medical attention. The contact stated that the Fire Department arrived at the scene and extinguished the fire but not before the vehicle was destroyed. A police report was filed. The manufacturer was notified of the failure. The contact related the failure to NHTSA Campaign Number 10V517000 (Engine and Engine Cooling) and 08V284000 (Equipment) for which the VIN was included. The approximate failure mileage was 182,000.
- Service brakes
The contact owns a 2006 Nissan Armada. The contact stated while driving 40 MPH, the brakes warning light illuminated. The brake pedal was depressed and made an abnormal metal-on-metal sound. The contact slowed down, veered to the side of the road, and restarted the vehicle however, the failure…
The contact owns a 2006 Nissan Armada. The contact stated while driving 40 MPH, the brakes warning light illuminated. The brake pedal was depressed and made an abnormal metal-on-metal sound. The contact slowed down, veered to the side of the road, and restarted the vehicle however, the failure persisted. The vehicle was taken to an independent mechanic to be diagnosed. The mechanic retrieved a delta stroke error code however, the vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 230,815.
- Service brakes
I was traveling at low speed and step on the brakes and hear a terrible grinding sound coming from the brakes in addition to a spring like sound and a significant reduction in braking power. The brake lights came on. This continues until I pull off the road and shut off the engine and then start it…
I was traveling at low speed and step on the brakes and hear a terrible grinding sound coming from the brakes in addition to a spring like sound and a significant reduction in braking power. The brake lights came on. This continues until I pull off the road and shut off the engine and then start it back up and the brakes work fine. The next day, while exiting the highway...brake light came on, little or no braking power and a shudder in the breaks. And then it happened again as I pull up to the driveway to park my armada. This IS a safety issue and I really hope that nissan will take care of this issue.
- Service brakes
I have a recall on brake booster can you help me I take the truck to the dealer and they don't want to fix it what can I do this IS dangerous before something happened the light IS on the dash board please help me solve this problem thank you *tr
- Service brakes
The emergency and importance to recall my vehicle which IS a 06 nissan armada and I'm sure there IS plenty more out there. The issue IS that my brakes will not engage out of nowhere. They will stop working and it feels as if the brakes are locking and grinding . This happens when going down hill , the most dangerous times it has happened to me IS driving while in the freeway.
- Service brakes
I have a 06 armada my big concern it's the brake light comes on an the brakes don't respond correctly it's hard to stop it's been happening for a while I take my vehicle to the dealer and they said there IS no recall for it even the mechanic can't tell me nothing this IS a seriously safety problem for all the persons who drive this vehicles keep precaution
- Service brakes
TL* the contact owns a 2006 nissan armada. While decelerating from 70 mph, the brakes failed to engage. The contact continued to depress the brake pedal with force until the anti-lock braking system engaged. The contact veered to the shoulder of the road and turned off the vehicle. Once it was…
TL* the contact owns a 2006 nissan armada. While decelerating from 70 mph, the brakes failed to engage. The contact continued to depress the brake pedal with force until the anti-lock braking system engaged. The contact veered to the shoulder of the road and turned off the vehicle. Once it was restarted, the vehicle resumed normal operation. The failure was experienced several times. Banister nissan of chesapeake (930 n battlefield blvd, chesapeake, va 23320, (757) 214-6342) was contacted to schedule a diagnostic test. The vehicle was taken to an independent mechanic to be diagnosed, but a failure code could not be located. The manufacturer was made aware of the failure and did not assist. The vehicle was not repaired. The failure mileage was approximately 200,000.
- Service brakes
This IS the 5TH time this had happened in one year, my brake light would come on for no reason and I would have no brakes, I check my fluid and pad nothing was wrong please call a recall before someone dies
- Air bags · Service brakes · Unknown or other
For several month now off and on while I'm driving the truck makes a loud noise, steering wheel shakes then I heard a spring noise. It almost feels like the truck IS going to fall apart. Then the slip amd vdc off sensor comes on. Then it stops sensor lights go away. Then it happens again, it's been real frequent lately.
- Electrical system · Engine
Engine stalls. while driving, the vehicle stalls. this continues to occur when coasting, acellerating or braking and causes danger as I was unable to safely pull over from the left and middle lane of traffic, or on the freeway. occurs while driving straight. research shows a faulty ecm with…
Engine stalls. while driving, the vehicle stalls. this continues to occur when coasting, acellerating or braking and causes danger as I was unable to safely pull over from the left and middle lane of traffic, or on the freeway. occurs while driving straight. research shows a faulty ecm with silicone dioxide build up on the ecm sensor contact inside the ipdm. found : https://www.cars.com/recalls/nissan-armada-2006/ though no recall found on current search. recal 10v517000 but can no longer find it on nhtsa search site.
- Service brakes
Brakes failure ( suddenly brake light on ) "i was on my way home from work and a car cut me off,brake lights came on, I stepped on my brakes and the brakes went down to the floor and I heard and felt a grinding noise. I immediately drove out the way and thank god there was no vehicles parked in…
Brakes failure ( suddenly brake light on ) "i was on my way home from work and a car cut me off,brake lights came on, I stepped on my brakes and the brakes went down to the floor and I heard and felt a grinding noise. I immediately drove out the way and thank god there was no vehicles parked in the area I had turned into. Then after that I did turn off the vehicle then turn it on and everything wors good but anyway driving with a lot concerning that might be happen again. I did take it to the dealer but they said could not find anything wrong, anyway they charge me about $ 200 dollars for the test. Note; this already happened five times, three of them on just one day(02/15/2018) hope that nissan company understand that this defect/ failure IS very dangerous and needs to be attended very seriously. (xxxx) nissan armada 2006 (xxxx) parts of this document have been redacted to protect personally identifiable information pursuant to the freedom of information act (foia), 5 u.s.c. 552(B)(6).
- Unknown or other
My car died after came out from store the car crank but it won't start no engine light on new fuel pump new spark pug new fuel relay still a lot people say it may be I p d m
- Electrical system · Service brakes · Unknown or other
Adc slip light come on the car cut off and have no power motion and in park hightway and street
- Service brakes
The brakes fail when brake sensor turns on periodically while car IS in motion. This happens without warning. The only way to resolve this IS to turn off the car. I have been in many near accidents because of this manufacturing defect that many owners have complained about.
- Service brakes
This IS my second time with brake failure due to a faulty brake booster. The first time in 2011 and now in 2018. Brake light comes on and grinding noise with very little brake pressure. Taken to dealership brake booster replaced $982. my question IS did they replace defective parts with upgrade. It IS a well known issue that to me nissan IS ignoring till there IS a fatal accident. Dealer states delta sensor faulty.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Engine compartment fire
On may 30, 2008, the office of defects investigation (odi) opened a preliminary evaluation based on consumer complaints alleging that smoke and/or fire erupted in the engine compartment of model year (my) 2005-2006 nissan armada and titan vehicles.by letter dated june 24, 2008, nissan notified the national highway…
On may 30, 2008, the office of defects investigation (odi) opened a preliminary evaluation based on consumer complaints alleging that smoke and/or fire erupted in the engine compartment of model year (my) 2005-2006 nissan armada and titan vehicles.by letter dated june 24, 2008, nissan notified the national highway traffic safety administration (nhtsa) that it will conduct a safety recall (nhtsa #08v284) for my2005-2006 nissan titan, armada and infiniti QX56 vehicles manufactured from march 17, 2005 to august 21, 2006 that are equipped with a 90-watt air conditioning condenser fan.the recall involves approximately 180,664 vehicles.this also includes approximately 5,689 subject condenser fans, some of which may have been installed in my2004 and pre-march 17, 2005 my nissan titan, armada or infiniti QX56 vehicles as a service replacement part.nissan dealers will install a special thermal protector kit on existing fans that will eliminate the potential for a fire to occur.nissan north america, inc. (Nissan) informed odi that the 90-watt air conditioning condenser fan was manufactured out-of-specification allowing for excessive water intrusion and inadequate drainage of moisture that may accumulate in the motor as a result of water intrusion or condensation.if sufficient moisture accumulates in the motor without adequate drainage, corrosion may occur.the corrosion can cause an increase in internal friction and an increase in the electrical current draw, resulting in an increase in the temperature of the motor that could melt its wiring insulation and other plastic components and form a gas.if two wires without insulation touch each other and create a spark, this gas could ignite and result in a fire.the action taken by nissan IS sufficient to resolve the issue raised by this investigation.accordingly, this investigation IS closed.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11007000VOLUNTARY SAFETY RECALL CAMPAIGN 2004-2012 ARMADA, TITAN, AND 2004-2009 QUEST; DRIVER AIR BAG COVER CAMPAIGN ID #: PC944, PC946, PC947, PC949 APPLIED VEHICLES: 2004-2012 Armada (TA60) 2004-2009 Quest (V42) 2004-2012 Titan (A60) Check Service COMM or Dealer Business Systems (DBS) National Service History to confirm campaign eligibility. INTRODUCTION Nissan is conducting this voluntary safety recall campaign on certain specific model year 2004-2012 Armada, 2004-2012 Titan, and 2004-2009 Quest vehicles, to inspect and if necessary, replace the driver Air Bag Cover. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers PC944, PC946, PC947 and PC949 to this campaign. The vehicle specific number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealers responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealers inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11004962VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11004961CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11004960CAN COMMUNICATION CODES DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001201WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001194REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001191WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10243708DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10239062SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
- 1023906012 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
- 10235710INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
- 10235707VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10233896ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232658REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232657WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232656WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232652DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10208946CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10192821SERVICE INFORMATION Replacement 5-speed rear wheel drive Automatic Transmission (A/T) assemblies and replacement control valves (valve bodies) now come with blank Transmission Control Modules (TCMs). Blank TCMs come without software and must be programmed (not reprogrammed) and then configured after they are installed. When ordering a replacement A/T or control valve, use the Nissan electronic parts information systems to obtain the correct software program part number See this bulletin for further detail.
- 10192805IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
- 10192801SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
- 10192747IF YOU CONFRIM An oil leak at the right side block ball plug behind the alternator. ACTION Use a punch to seat the block ball plug in the hole (refer to the Service Procedure). NOTE - Do not replace the engine block for this incident if it should occur. See this bulletin for further detail.
- 10192727SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
- 10192679SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further details.
- 10192677SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
- 10192638SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
- 10192591SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
- 10192524SERVICE INFORMATION When diagnosing possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.
- 10192513SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
- 10192474SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
- 10192394SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
- 10192326SERVICE INFORMATION The specifications for the intake and exhaust valves and valve lifter service parts have been changed. * The valve stem length of both intake and exhaust valve has been increased (Figure 1) and are a direct replacement for the shorter style valve. * The related valve lifter cup has been shortened (Figure 2) and the point at which the valve lifter contacts the valve stem has been shortened (not shown). These service parts will require that the valve and valve lifter be replaced at the same time. See this bulletin for further details.
- 10192305SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
- 10192234Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
- 10192233Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
- 10192231SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
- 10192217If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
- 10192216SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
- 10192192As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
- 10192145SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
Every Nissan Armada model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.