2007 Nissan Armada
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Nissan › Armada › 2007
These records cover every 2007 Nissan Armada. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
3 recalls name the 2007 Nissan Armada. Newest first.
Nissan IS recalling certain front and rear lower links, p/nos. 54501Zq00a, 54500zq00a, 551a1zq00a, 551a0zq00a , 54501ea00a, 54500ea00a, 551a1ea500, 551a0ea500, 54501zr00a, and 54500zr00a, sold between november 25, 2009 and may 14, 2010 as replacement parts for model year 2004 through 2010 titan, armada, and QX56, and model years 2005 through 2010 frontier…
Risk and remedy
Risk
If the collar weld separates, the vehicle handling will deteriorate, possibly resulting in a vehicle crash.
Remedy
Nissan will notify owners and dealers will replace any affected lower link free of charge. the safety recall began on july 12, 2010. owners may contact nissan at 1-800-647-7261.
Nissan IS recalling certain model year 2005-2009 titan, armada, and infiniti QX56 vehicles. the instrument panel fuel gauge may inaccurately display that the vehicle still has some fuel, typically about one quarter tank, when the fuel tank IS empty.
Risk and remedy
Risk
This could cause the vehicle to run out of gas and stall on the highway, which could cause a crash.
Remedy
Dealers will replace the fuel sender unit inside the fuel tank with a new improved sender card. this service will be performed free of charge. the safety recall began on march 22, 2010. owners may contact nissan at 1-800-647-7261.
Certain sport utility vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 210, 'seat belt assembly anchorages.' the driver's side third row seat belt upper anchor bracket may be cracked.
Risk and remedy
Risk
In the event of a crash, a seat occupant may not be properly restrained increasing the risk of personal injury.
Remedy
Dealers will replace the seat belt bracket free of charge. the recall began on november 1, 2007. owners may contact nissan at 1-800-647-7261.
Owner complaints
86 complaints
What owners report most
Latest complaints
- Air bags
I called the manufacturer, Nissan Consumer Affairs at [XXX] - After entering my VIN# the automated computer system stated there is no recalls for my vehicle, even though your NHTSA Vehicle Safety Website lists the following recall: February 09, 2023 Manufacturer Recall Number: PC947 NHTSA Recall…
I called the manufacturer, Nissan Consumer Affairs at [XXX] - After entering my VIN# the automated computer system stated there is no recalls for my vehicle, even though your NHTSA Vehicle Safety Website lists the following recall: February 09, 2023 Manufacturer Recall Number: PC947 NHTSA Recall Number: 23E-012 Recall Status: Recall Incomplete Please advise how to fix this recall. Thank you. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Service brakes
On a continuing basis, while vehicle is in motion, applying the brakes causes brake pedal to sink to the floorboard with loss of braking power and with loud grinding noise coming from front of vehicle. Turning vehicle off then back on temporarily fixes the issue.
- Air bags
The contact owns a 2007 Nissan Armada. The contact received notification of NHTSA Campaign Number: 23E012000 (Air Bags) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The…
The contact owns a 2007 Nissan Armada. The contact received notification of NHTSA Campaign Number: 23E012000 (Air Bags) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The vehicle was not taken to the dealer or an independent mechanic. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The air bag warning light was illuminated. The failure mileage was unknown. VIN tool confirms parts not available.
- Engine · Power train
The contact owns a 2007 Nissan Armada. The contact stated that while driving at an undisclosed speed, the vehicle lost motive power. An unknown message was displayed after the failure occurred. The vehicle was towed to the residence. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 130,000.
- Service brakes
I was driving in traffic and my breaks went out and I almost got in a collision. The breaks at first didn't work and then were bouncing and grinding to stop and the break warning light came on. I swerved and barely missed another car. I pulled over in a parking lot there was a burning smell and…
I was driving in traffic and my breaks went out and I almost got in a collision. The breaks at first didn't work and then were bouncing and grinding to stop and the break warning light came on. I swerved and barely missed another car. I pulled over in a parking lot there was a burning smell and let it sit for 4hr. I took it to get the breaks fixed an they couldn't find any issues with the breaking system except for the Delta Stroke Sensor Failure. I understand this has a been an ongoing issue with cars. One situation killed 3 people and Nissan lost a $25M lawsuit on this. I can't understand why this wouldn't be on a recall as issues with the breaking system is life threatening. My car is now at Nissan getting fixed, has been there for 2 weeks, they still can't figure out the issue with the Delta Sensor breaking system. This is very serious and no matter what age of the car, should be covered under a recall. You can find hundreds of articles online to understand how many cars are affected. Please look into this and issue a recall.
- Unknown or other
Second time that horn has failed and had to replace steering well assy. twice horn failed to work. all most had accident. and now the horn does not work again.
- Service brakes
I've had several near collisions because breaks slip as though the ABS system is engaged and the brake light comes on. I have to find an area to pull off to stop the car then restart it to get rid of the problem temporarily.
- Steering · Unknown or other
5 years ago another car jumped in front of SUV I went to use horn it did not work. I had it replaced at an expenseve price. And just the other day a little child ran out from IS yard I went to use horn and again it has stoped working
- Structure › Body
The paint on my hood and roof has discolored. It looks like the clear coat was defective. I've noticed it on many other nissan armadas and nissan titan pick up trucks. IS there a pattern on lousy paint coatings?
- Service brakes
ABS malfunction while driving ,it happens all the time it grinds and it will not stop right away im scared it will cause accident.the problem disappear when you turn off the engine.then it will happen again lights will come on brakes grind and you wont be able to stop the vehicle right away.i almost have a crash a lot of times when this problem happen.please investigate to all nissan armada owners.
- Air bags
Airbag light randomly began flashing. Code pulled as b1035 crash zone sensor. This vehicle has never been in any type of accident. upon researching vehicle and code it shows the same year and makes of vehicles having exact symptoms as well as code of b1035. Even on the nhtsa website regarding this…
Airbag light randomly began flashing. Code pulled as b1035 crash zone sensor. This vehicle has never been in any type of accident. upon researching vehicle and code it shows the same year and makes of vehicles having exact symptoms as well as code of b1035. Even on the nhtsa website regarding this recall- it does show a picture on the pdf file of a nissan armada image showing instructions on how to install the recalled sensor. This needs to be reviewed immediately and make corrections with adding the armada being part of the recall. It has same exact sensor part and I feel that this should not be held on the vehicle owners part as clearly it IS a defective part. there will be additional calls I will make if needed to the attorney general's office if this does not get resolved in a prompt manner and if an accident occurs and does not deploy airbags because of recalled part that was not appropriately added to a nhsta list, there will be legal advice sought regarding liability and injuries.
- Service brakes
While driving the car will slow down and I will notice the brake light IS on. Then I will hear like a grinding sound. As if im driving with emergency brakes on. The parking brakes engage while im driving. We took car to a nissan dealer for servicing but they could not detect any problem. There IS…
While driving the car will slow down and I will notice the brake light IS on. Then I will hear like a grinding sound. As if im driving with emergency brakes on. The parking brakes engage while im driving. We took car to a nissan dealer for servicing but they could not detect any problem. There IS certainly a problem with braking system. I am afraid this will cause an accident. It has happened about 7 times in the last 2 weeks. We just got new brakes on oct. 5 2019. This problem a few years ago and it will happen a few times a year but lately its happening more often. It staryed back on or about OCT.1, 2019.
- Air bags
Several weeks ago the airbag warning light on the dashboard began flashing and has continued to do so to this day. I am filing this report to confirm others who have reported the same experience.
- Air bags
My mechanic did a diagnostic and it showed driver side airbag module open my airbag light on dashboard has been flashing for months
- Electrical system
Driving one day on interstate way and city driving another car was drifting or attempted to cross into my lane, went to use horn and it failed. has not been working, have noticed that volume control and cruise control has stopped working. dealer ship stated that the spiral cable IS bad and have many of this assembly's available. *tr
- Electrical system · Electrical system › Horn
Driving need to use horn and it did not work checked all relays an fuse all good can not get it to work. *tr
- Engine and engine cooling › Exhaust system › Manifold/header/muffler/tail pipe
TL* the contact owns a 2007 nissan armada. While the vehicle was stationary, the exhaust manifold fractured without warning. Exhaust fumes entered into the cabin of the vehicle. The vehicle was not repaired. The manufacturer was made aware of the issue. The failure mileage was 120,000. The vin was not available. updated 10/18/16*lj *tr
- Service brakes
Brake light on my dash will come on and all of a sudden I hit the brake and a violent jerking and grinding sound on the brake. The brake feels like it would slip for little and but will still stop the vehicle. I turn the engine off and everything became normal again. I took it to the dealer to get…
Brake light on my dash will come on and all of a sudden I hit the brake and a violent jerking and grinding sound on the brake. The brake feels like it would slip for little and but will still stop the vehicle. I turn the engine off and everything became normal again. I took it to the dealer to get check and they said that the were not able to mirror the problem and send the vehicle back to me. Now it happen several times again and I would just turn the engine off and resolves the issue. This issue has a class action lawsuit and won. There had been plenty of complaint regarding this problem too from other owners. What I don't understand IS that why IS there no recall regarding this problem still.. Why am I being force to pay for this defect first and then get partially reimbursed
- Service brakes, hydraulic
TL* the contact owns a 2007 nissan armada. While driving 30 mph, the brake warning light illuminated. In addition, the brake pedal was depressed, but the vehicle began to vibrate and took a longer distance to stop the vehicle. The failure recurred on numerous occasions. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was 73,000. updated 09/06/16*lj
- Suspension
Control arm front and rear twice 2014 and 2015
- Service brakes
Brake light indicator came on. Brakes became unresponsive. When pushing the brake pedal, the brakes made a crunchy noise, like metal rubbing together. There was a lot of noise. It was difficult to stop the vehicle. I was in motion on a city street. When I turned the car off and back on, it went back to "normal" with no brake light indicator on.
- Service brakes
While driving approx. 30 mph down city street in morning traffic, the emergency brake light randomly comes on and when I try to brake the car make a grinding noise and I do not have full braking power. When you turn the car off it resets and the car resumes to functioning normally. Local mechanic…
While driving approx. 30 mph down city street in morning traffic, the emergency brake light randomly comes on and when I try to brake the car make a grinding noise and I do not have full braking power. When you turn the car off it resets and the car resumes to functioning normally. Local mechanic tested once, got no codes so replaced master cylinder. A week later it happens again; took it back and got a code c1179-brake booster....a $900+ job. Refuse to pay this kind of money when research show that this did not resolve the issue. Wrote to nissan but got no reply. Conducted a search and found that hundreds of people are having the same issue.
- Engine
When I start my vehicle a big white cloud of smoke come out the tailpipe.
- Service brakes
Randomly when applying brakes during normal travel ranging and speeds from 25 to 70 a loud grinding noise IS heard the brake light comes on in the vehicle IS extremely hard to stop. If the vehicle IS shut off the system will reset and it will be as if nothing happened. Took the vehicle to a local…
Randomly when applying brakes during normal travel ranging and speeds from 25 to 70 a loud grinding noise IS heard the brake light comes on in the vehicle IS extremely hard to stop. If the vehicle IS shut off the system will reset and it will be as if nothing happened. Took the vehicle to a local shop had the vehicle inspected with no discrepancies. It just happened again on 06 november. here IS a link of other people experiencing the same thing. http://m.carcomplaints.com/nissan/armada/2007/brakes/service_brakes.shtml
- Service brakes
TL* the contact owns a 2007 nissan armada. The contact stated that while driving at approximately 40 mph, the brake pedal was depressed as a loud noise emitted with the illumination of the brake warning indicator. After the engine was turned off and restarted, the vehicle resumed normally. The…
TL* the contact owns a 2007 nissan armada. The contact stated that while driving at approximately 40 mph, the brake pedal was depressed as a loud noise emitted with the illumination of the brake warning indicator. After the engine was turned off and restarted, the vehicle resumed normally. The failure became progressively worse over time. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The approximate failure mileage was 80,000.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11007000VOLUNTARY SAFETY RECALL CAMPAIGN 2004-2012 ARMADA, TITAN, AND 2004-2009 QUEST; DRIVER AIR BAG COVER CAMPAIGN ID #: PC944, PC946, PC947, PC949 APPLIED VEHICLES: 2004-2012 Armada (TA60) 2004-2009 Quest (V42) 2004-2012 Titan (A60) Check Service COMM or Dealer Business Systems (DBS) National Service History to confirm campaign eligibility. INTRODUCTION Nissan is conducting this voluntary safety recall campaign on certain specific model year 2004-2012 Armada, 2004-2012 Titan, and 2004-2009 Quest vehicles, to inspect and if necessary, replace the driver Air Bag Cover. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers PC944, PC946, PC947 and PC949 to this campaign. The vehicle specific number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealers responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealers inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11004962VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11004961CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11004960CAN COMMUNICATION CODES DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001201WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001194REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001191WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10243708DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10239062SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
- 1023906012 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
- 10235710INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
- 10235707VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10233896ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232658REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232657WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232656WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232652DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10208946CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10192821SERVICE INFORMATION Replacement 5-speed rear wheel drive Automatic Transmission (A/T) assemblies and replacement control valves (valve bodies) now come with blank Transmission Control Modules (TCMs). Blank TCMs come without software and must be programmed (not reprogrammed) and then configured after they are installed. When ordering a replacement A/T or control valve, use the Nissan electronic parts information systems to obtain the correct software program part number See this bulletin for further detail.
- 10192805IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
- 10192801SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
- 10192747IF YOU CONFRIM An oil leak at the right side block ball plug behind the alternator. ACTION Use a punch to seat the block ball plug in the hole (refer to the Service Procedure). NOTE - Do not replace the engine block for this incident if it should occur. See this bulletin for further detail.
- 10192727SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
- 10192679SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further details.
- 10192677SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
- 10192638SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
- 10192597SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
- 10192591SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
- 10192524SERVICE INFORMATION When diagnosing possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.
- 10192513SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
- 10192474SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
- 10192394SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
- 10192326SERVICE INFORMATION The specifications for the intake and exhaust valves and valve lifter service parts have been changed. * The valve stem length of both intake and exhaust valve has been increased (Figure 1) and are a direct replacement for the shorter style valve. * The related valve lifter cup has been shortened (Figure 2) and the point at which the valve lifter contacts the valve stem has been shortened (not shown). These service parts will require that the valve and valve lifter be replaced at the same time. See this bulletin for further details.
- 10192305SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
- 10192266SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Nissan vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >> EVAP SYSTEM CLOSE. NOTE: Use Essential Tool J-42909 or equivalent to pressurize the EVAP system. - With a "Smoke" leak detection machine. Refer to the machine's Operator's Manual for proper use. Make sure the customer is informed of the proper fuel filler cap installation.
- 10192234Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
- 10192233Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
- 10192231SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
- 10192217If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
- 10192216SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
Every Nissan Armada model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.