2008 RAM 3500
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2008 RAM 3500. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
1 recall names the 2008 RAM 3500. Newest first.
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Charger Police vehicles, 2007-2013 RAM 3500 Cab Chassis, 2008-2013 RAM 4500 and 5500 Cab Chassis, and 2013 RAM 2500 and 3500 vehicles. The affected vehicles have a 220 amp alternator that may suddenly fail.
Risk and remedy
Risk
If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash. There is also the possibility that the alternator may short circuit, increasing the risk of a fire.
Remedy
Chrysler will notify owners, and dealers will replace the alternator with a revised alternator, free of charge. The recall began on December 23, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S68.
Owner complaints
4 complaints
What owners report most
Latest complaints
- Steering · Suspension
Vehicle experienced the "death wobble", replaced the steering gear box stabilizer/brace, did not fix the problem, this happens when going highway speeds and you encounter bumps, the vehicle shakes violently and you have to pull over and slow down to stop the shaking, the other fixes are very expensive, and should be a recall. Numerous other people have experienced the same issues with these vehicles.
- Steering
My complaint IS with the front end of my 2008 dodge RAM 3500 quad cab dually diesel. I have been getting the death wobble after replacing everything in the front end except the drag link steering link. I have the factory "y" type and was told dodge was replacing them with the "t"style. Please…
My complaint IS with the front end of my 2008 dodge RAM 3500 quad cab dually diesel. I have been getting the death wobble after replacing everything in the front end except the drag link steering link. I have the factory "y" type and was told dodge was replacing them with the "t"style. Please advise before I get killed in this thing. Highway between 40 and 65 I hit a bump andthe front end starts jumping all over the place uncontrollably until I come to an almost stop.
- Electrical system · Electronic stability control (esc) · Exterior lighting
The 4X4 actuator kept clicking in and out and damaged my transfer case where I had to pay for a new one, now it's starting to do it again. Also my heater blows cold on diver side and hot on passenger side. All services have been done but the light keeps coming on and off, saying I need to have it serviced. head lights and dash lights keep fluctuating in bright and deeming.
- Steering › Linkages › Tie rod assembly · Suspension
TL* the contact owns a 2008 RAM 3500. While driving, the tie rod fell off on the passenger side of the vehicle. The contact drove to fremont motor cody (3127 big horn ave, cody, wy 82414), but they could not repair the vehicle. The contact replaced the tie rod himself. The manufacturer was contacted and was unable to provide assistance. The approximate failure mileage was 120,000.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10229181Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223602Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223599Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
- 10220994Part Description: Insulator in Lever Assembly - Valve Body - Trans Issue Description: The manual valve insulator, attaching rivet and an instruction sheet are now available as a kit. If the insulator requires replacement please order 68253099AA. Note: Insulator color is not relevant for service
- 10220868Transfer Case Gear Motor/Actuator Installation Guidelines.
- 10220837GEAR MOTOR, Transfer Case The gear motor assembly is shipped in AWD/2WD position. The transfer case needs to be positioned in AWD/2WD position to properly assemble gear motor to T-Case. Please reference Star Online publication S2121000003 for further details. Do not have the transfer case in in another position other than AWD/2WD and rotate the motor to align the bolt holes as this could result in damage to the gear motor.
- 10220496PLATE - CLUTCH PRESSURE For 68RFE trans use selective fit pressure plates between the overdrive and reverse clutch packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$
- 10220470Noise coming from the rear HVAC blower due to interference.
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10218307Flash: UConnect and Voice Recognition Inoperative This bulletin involves replacing the Hands Free Module (HFM). The customer may describe the following conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality
- 10218178Part Description: Thermostat, Engine Issue Description: Important! There has been an application change to the Cummins turbo diesel thermostat. When replacing a thermostat confirm the correct replacement is choosen.~ 2010, 2011, and 2012 RAM Trucks 2500/3500/4500/5500 engine coolant operating temperature has been increased to 200 degrees requiring thermostat 68067109AA.~ 2009, 2013, and 2014 RAM Trucks 2500/3500/4500/5500 engine coolant operating temperature is 190 degrees requiring thermostat 68005464AA.~ These thermostats are not interchangeable and doing so will result in reduced engine performance.
- 1021641868069384A$, R8069384A$, 68086182A$, R8027067A$, RL002012A$ - Gasket, Cylinder Head Cover Before replacing injectors for Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.~
- 10216395Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10216348Heavy Duty Filtration MOPAR Retrofit or Add On Parts Available
- 10215990Cummins 6.7L Turbo Diesel Common Diagnostic Process New 6.7L CumminsTurbo Diesel Common Diagnostic Process is now available as part of the standard diagnostic process located in TechCONNECT>Service Info.
- 10215976MIL Illumination Due to P2000, P2A00 and/or P2A01 FRONT O2 sensor. Customer may experience MIL illumination. Further investigation by the technician may find one or more of the following DTC(s) present: P2000 - NOX Absorber Efficiency Below Threshold - Bank 1. P2A00 - O2 Sensor 1/1 Circuit Performance. P2A01 - O2 Sensor 1/2 Circuit Performance.
- 10215830CONVERTER KIT, Torque The torque converter does not include the driveplate to torque converter fasteners. Order six (6) new 06504383 bolts as they have patchlock.
- 10191460Valve Body. These may cause over drive cycling.
- 10190615Transfer Case Gear Motor/Actuator Installation Guidelines.
- 10190584GEAR MOTOR, Transfer Case The gear motor assembly is shipped in AWD/2WD position. The transfer case needs to be positioned in AWD/2WD position to properly assemble gear motor to T-Case. Please reference Star Online publication S2121000003 for further details. Do not have the transfer case in in another position other than AWD/2WD and rotate the motor to align the bolt holes as this could result in damage to the gear motor.
- 10189383MIL Illumination Due to P2000, P2A00 and/or P2A01 This bulletin involves verifying all service bulletins related to high sooting issues have been properly addressed, inspecting both Oxygen (O2) sensors and either cleaning the sensors or replacing sensors, and installing an O2 Sensor Shield on the exhaust pipe in the area of the FRONT O2 sensor. Customer may experience MIL illumination. Further investigation by the technician may find one or more of the following DTC(s) present: ? P2000 - NOX Absorber Efficiency Below Threshold - Bank 1. ? P2A00 - O2 Sensor 1/1 Circuit Performance. ? P2A01 - O2 Sensor 1/2 Circuit Performance.
- 10188685Cummins 6.7L Turbo Diesel Common Diagnostic Process New 6.7L CumminsTurbo Diesel Common Diagnostic Process is now available as part of the standard diagnostic process located in TechCONNECT>Service Info.
- 10188671MIL Illumination Due to P2000, P2A00 and/or P2A01 FRONT O2 sensor. Customer may experience MIL illumination. Further investigation by the technician may find one or more of the following DTC(s) present: P2000 - NOX Absorber Efficiency Below Threshold - Bank 1. P2A00 - O2 Sensor 1/1 Circuit Performance. P2A01 - O2 Sensor 1/2 Circuit Performance.
- 10188620PLATE - CLUTCH PRESSURE For 68RFE trans use selective fit pressure plates between the overdrive and reverse clutch packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$
- 10187009CONVERTER KIT, Torque The torque converter does not include the driveplate to torque converter fasteners. Order six (6) new 06504383 bolts as they have patchlock.
- 10175743Disinfectant Solution Recommended for COVID-19
- 10175735Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
- 10175677Valve Body Pressure Testing Plug Inspection
- 10169249Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10169247Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10169245Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10166537RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
- 10162521Safety Recall V47 / NHTSA 19V-325 Backlite Glass Parts Ordering Information
- 10162520Vehicles Eligible For CSN U07 And V08, V11 or V16 Important Update To U07 Dealer Instructions
- 10162513Warranty Operations Newsletter ? Volume 5, Issue 5
Every RAM 3500 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.