2015 RAM 3500
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2015 RAM 3500. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
16 recalls name the 2015 RAM 3500. Newest first.
Chrysler (FCA US, LLC) is recalling certain 2015-2020 Ram 1500 Classic, 2015-2016 Ram 3500, and Ram 2500 vehicles, and 2016 Ram 3500 Cab Chassis with a gross vehicle weight rating less than 10,000 lbs. The side air bag inflatable curtain (SABIC) inflator end cap may detach from the inflator, or the inflator sidewall may rupture.
Risk and remedy
Risk
A separated inflator end cap or inflator rupture can allow compressed gas to escape, resulting in the end cap or other components being propelled into the vehicle, increasing the risk of injury or crash.
Remedy
Dealers will inspect and replace as necessary, the SABIC assemblies, free of charge. Interim owner notification letters were mailed on October 4, 2021. Owner notification letters were mailed on May 26, 2022. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is Y55.
Chrysler (FCA US, LLC) is recalling certain 2012-2021 RAM 3500, 3500 Cab Chassis, 4500 Cab Chassis, and 5500 Cab Chassis vehicles. Incorrect information in the Service and Owner's Manuals may cause the flanged lug nuts to be over-tightened, which could result in a broken wheel stud and possible wheel separation.
Risk and remedy
Risk
Wheel separation can cause a vehicle crash.
Remedy
Dealers will update the torque specification in the owner's manual and other published service documents. Dealers will also inspect the vehicle's wheel studs, replacing them if necessary, free of charge. Owner notification letters were mailed on November 30, 2021. Campaign Y36 owner notification letters were mailed on November 30, 2021. Campaign Y26 owner notification letters were mailed on December 1, 2021. Owners may contact FCA US customer service at 1-800-853-1403. FCA US's numbers for this recall are Y26 and Y36.
Chrysler (FCA US LLC) is recalling certain 2015-2017 Ram 1500, 2500 and 3500 pickup trucks equipped with an 8 foot bed and a power locking tailgate. Chrysler is also recalling all 2013-2014 and 2018 Ram 1500, 2500 and 3500 pickup trucks built before April 1, 2018 with a 6 or 8 foot bed and a power locking tailgate. On August 29, 2019 Chrysler expanded the…
Risk and remedy
Risk
If the tailgate opens while the vehicle is being driven, cargo may fall out the vehicle and create a road hazard, increasing the risk of crash.
Remedy
Chrysler will notify owners, and dealers will repair the tailgate latch, free of charge. The recall began May 23, 2019. Chrysler is expected to notify owners of the expanded population on October 18, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA US's number for this recall is V44. Note: 2015-2017 MY Ram 1500 pickup trucks with truck beds other than 8 foot, are currently covered under NHTSA recall 18V-486 for this issue.
Chrysler (FCA US LLC) is recalling certain 2013-2018 Ram 3500 and 2014-2018 Ram 3500 Chassis Cab and Ram 2500 vehicles. The outboard steering linkage jam nut may loosen, allowing one end of the drag link to separate.
Risk and remedy
Risk
A drag link separation can cause a loss of steering control, increasing the risk of crash.
Remedy
Chrysler will notify owners, and dealers will check the steering linkage jam nut tightness, replacing the drag link assembly or welding the nut to the adjuster sleeve, free of charge. The recall began March 22, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V06.
Streetcar ORV LLC (Streetcar) is recalling certain American Expedition Vehicles (AEV) 3" Dualsport aftermarket suspension kits, part numbers N0436000 and N0436001, sold for installation on 2013-2018 RAM 2500 and 3500HD trucks. Improper installation and machining of the original equipment steering knuckle may weaken the joint between the steering drag link…
Risk and remedy
Risk
The weakened connection may result in a fractured steering drag link, causing a loss of steering and increasing the risk of a crash.
Remedy
Streetcar will notify owners and dealers will inspect and install a new steering knuckle, free of charge. The recall began December 3, 2018. Owners may contact AEV customer service at 1-248-926-0256, extension 500.
Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.
Risk and remedy
Risk
If the tailgate latch releases and the tailgate opens while driving, cargo may fall out, creating a road hazard and increasing the risk of a crash.
Remedy
Chrysler will notify owners, and dealers will repair the vehicle, free of charge. The recall began September 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U74.
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb)…
Risk and remedy
Risk
If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy
Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the extinguisher from…
Risk and remedy
Risk
If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.
Remedy
Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1-800-853-1403 or Kidde customer service service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.
Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the…
Risk and remedy
Risk
Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.
Remedy
Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T79.
Chrysler (FCA US LLC) is recalling certain 2013-2017 RAM 2500, 3500, 3500 Cab Chassis, 4500 Cab Chassis, and 5500 Cab Chassis vehicles, equipped with Cummins 6.7L Turbo Diesel engines that have Concentric-brand water pumps without a vent hole. These water pumps may leak coolant.
Risk and remedy
Risk
The leaking water pump can increase the risk of an engine compartment fire.
Remedy
Chrysler will notify owners, and dealers will replace the water pumps, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T51.
Streetcar ORV LLC, dba American Expedition Vehicles (AEV) is recalling certain 2013-2017 RAM 2500 and 3500 heavy duty trucks, modified by AEV to be equipped with cast aluminum Katla 8.5" road wheels. The outer surface of the wheel may fracture, resulting in rapid air loss.
Risk and remedy
Risk
If the wheel fractures, a loss of vehicle control can occur, increasing the risk of a crash.
Remedy
AEV will notify owners, and dealers will replace the wheels with wheels of similar value, free of charge. The recall began on August 30, 2017. Owners may contact AEV customer service at 1-248-926-0256 extension 500.
Chrysler (FCA US LLC) is recalling certain model year 2013-2016 Ram 1500, Ram 2500, and 2014-2016 Ram 3500 vehicles. Certain driving conditions, such as driving off-road or debris striking the vehicle may cause the roll rate sensor to trigger a fault within the Occupant Restraint Controller (ORC). If this fault occurs, the rollover side curtain air bag…
Risk and remedy
Risk
If the rollover side curtain air bags and seat belt pretensioners are disabled, there is an increased risk of injury to the vehicle occupants in the event of a crash that necessitates activation of these safety systems.
Remedy
Chrysler will notify owners, and dealers will update the ORC software, free of charge. The recall began June 26, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T25.
Chrysler (FCA US LLC) is recalling certain model year 2015 RAM 2500 trucks, and RAM 3500 trucks and cab chassis. The affected vehicles may have inadequate welds securing the front track bar frame brackets, possibly resulting in the bracket components separating from the frame.
Risk and remedy
Risk
If the bracket components separate from the frame, the vehicle may have a reduced response to steering input, increasing the risk of a crash.
Remedy
Chrysler will notify owners, and dealers will weld on a new track bar frame bracket or replace the frame of the vehicle, free of charge. The recall began on September 14, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S58.
Chrysler (FCA US LLC) is recalling aftermarket Mopar Canvas Seat Covers for certain 2012-2016 RAM 1500, 2500, and 3500 trucks. These Mopar canvas seat covers were sold through Chrysler dealerships beginning October 15, 2015. The seat covers can impede the deployment of the seat thorax airbags.
Risk and remedy
Risk
If the seat cover impedes the air bag deployment, the seat thorax air bags may not provide adequate protection in the event of a crash, increasing the risk of a injury.
Remedy
Chrysler will notify owners to remove the front seat covers and return them for a full refund. The recall began on July 1, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S30.
Chrysler (FCA US LLC) is recalling certain model year 2013-2015 Ram 1500, 2500, 3500, 4500, and 5500, 2015 Chrysler 200, Chrysler 300, Dodge Charger, and Dodge Challenger, 2014-2015 Jeep Grand Cherokee, Cherokee, and Dodge Durango, and 2013-2015 Dodge Viper vehicles. The affected vehicles are equipped with radios that have software vulnerabilities that can…
Risk and remedy
Risk
Exploitation of the software vulnerability may result in unauthorized remote modification and control of certain vehicle systems, increasing the risk of a crash.
Remedy
Chrysler will notify and mail affected owners a USB drive that includes a software update that eliminates the vulnerability, free of charge. Optionally, owners may download the update to their own USB drive from http://www.driveuconnect.com/software-update/ or take their vehicle to a Chrysler dealer for immediate installation. In an effort to mitigate the effects of this security vulnerability, Chrysler has had the wireless service provider close the open cellular connection to the vehicle that provided unauthorized access to the vehicle network. This measure may not have been implemented on all vehicles and does not address access by other means that will be remedied by the software update. The recall began on August 25, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R40.
Chrysler (FCA US LLC) is recalling certain model year 2013-2015 Ram 1500, 2500, and 3500 trucks manufactured June 20, 2012, to January 26, 2015. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt…
Risk and remedy
Risk
Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy
Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on September 8, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R23.
Owner complaints
137 complaints3 involved a crash5 involved a fire1 injuries
What owners report most
Latest complaints
- Engine · Steering · Suspension
I own a 2015 Ram 3500 equipped with the 6.7L Cummins diesel engine. An authorized Ram dealership diagnosed an engine oil leak originating from the timing gear housing-to-engine block/cylinder block gasket. The leak has progressed beyond minor seepage. Engine oil is traveling down onto the…
I own a 2015 Ram 3500 equipped with the 6.7L Cummins diesel engine. An authorized Ram dealership diagnosed an engine oil leak originating from the timing gear housing-to-engine block/cylinder block gasket. The leak has progressed beyond minor seepage. Engine oil is traveling down onto the chassis/track bar area and is leaving drops on the ground. The dealer estimated the repair at approximately $4,000 because of the extensive labor required to access and reseal the timing gear housing. My concern is that an engine oil leak from this sealed housing may worsen over time and could potentially result in significant oil loss, contamination of nearby chassis components, or oil reaching hot engine/exhaust components depending on the path and severity of the leak. FCA/Stellantis has previously issued technical communications concerning oil leakage from the timing gear housing gasket. STAR Online Case [XXX], titled “Oil Leak From The Front Timing Gear Housing Gasket,” instructed dealership technicians to document the leak location, photograph the condition, and measure the breakaway torque of the timing gear housing retaining bolts. FCA also issued later engineering communications involving the rear gear housing/timing case gasket on later Ram 6.7L diesel trucks, including requests to document loose housing bolts and retain removed bolts for engineering analysis. I am submitting this complaint because I believe this may represent a recurring engine oil leakage condition involving the timing gear housing on Ram heavy-duty trucks equipped with the 6.7L Cummins diesel engine. I am requesting that NHTSA review owner complaints and manufacturer technical communications to determine whether this condition presents a broader safety-related defect. Vehicle: 2015 Ram 3500 Laramie 4x4 Engine: 6.7L Cummins Turbo Diesel VIN: [XXX] Approximate repair estimate: $4,000 Dealer diagnosis: timing gear housing-to-engine block/cylinder block gasket oil leak INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(
- Steering
The contact owns a 2015 Ram 3500. While attempting to have an alignment performed, the contact was informed that the steering drag link and the tie rod were both cracked. The failure caused rapid, premature wear on the tire. The contact stated that the vehicle was previously repaired under NHTSA…
The contact owns a 2015 Ram 3500. While attempting to have an alignment performed, the contact was informed that the steering drag link and the tie rod were both cracked. The failure caused rapid, premature wear on the tire. The contact stated that the vehicle was previously repaired under NHTSA Campaign Number: 19V021000 (Steering); and believed that the welding that was performed in the recall repair had directly caused the current failure. The vehicle was taken to an authorized dealer, where the technicians diagnosed the vehicle and determined that the previous recall repair made it impossible to perform a proper wheel alignment. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 193,000.
- Service brakes
The output voltage to the Trailer Braking system is low, only 7.5 volts. Other owners have the same problem. From what I understand there is an issue with the computer that keeps the Original Equipment trailer brake controller from delivering full power at speeds below 30 MPH. This is a safety…
The output voltage to the Trailer Braking system is low, only 7.5 volts. Other owners have the same problem. From what I understand there is an issue with the computer that keeps the Original Equipment trailer brake controller from delivering full power at speeds below 30 MPH. This is a safety hazard in stop and go driving. There are many complaints about this same problem in the Ram Forumz. Ram should be able to do a software update to fix the problem. One of the posts in the forum stated that Ram has the software update available but will charge a lot of money for it. This is a safety issue and these trucks should be recalled to fix the problem.
- Service brakes · Steering
humming from the hydroboost pump, actual issue is the high pressure steering line has a nylon tube inside the hose that breaks apart and moves throughout the system. Dodge had one revision of the hose on the early model years but this issue has gone unresolved. I am afraid if i cant get it fixed it may possibly cause the brakes or steering assistance to fail.
- Electrical system
The contact owns a 2015 Ram 3500. The contact stated while driving approximately 70 MPH in the left lane, the check engine warning light illuminated, and the vehicle simultaneously went into LIMP Mode. The contact was able to pull over to the shoulder of the roadway. The contact was able to…
The contact owns a 2015 Ram 3500. The contact stated while driving approximately 70 MPH in the left lane, the check engine warning light illuminated, and the vehicle simultaneously went into LIMP Mode. The contact was able to pull over to the shoulder of the roadway. The contact was able to continue driving, but the vehicle failed to exceed 5 MPH. Upon arriving to the residence, the vehicle was scanned, and it was determined that the turbo charger actuator had failed and needed to be replaced. The contact purchased an aftermarket part and repaired the vehicle. The dealer was not contacted. The contact later became aware that the failure was related to Chrysler Extended Warranty Coverage Number: X99; however, the contact had not received a notification from the manufacturer. The contact requested reimbursement from the manufacturer; however, the reimbursement was denied because the vehicle was not repaired by a dealer. The failure mileage was approximately 50,000.
- Steering · Suspension
There was a recall forced by the NTSB for a condition where the track bar adjustment nut would come loose and the truck would lose steering. The recall on the track bar was rectified by the dealer by welding the nut on the track bar. Now that the nut has been welded a proper alignment can not…
There was a recall forced by the NTSB for a condition where the track bar adjustment nut would come loose and the truck would lose steering. The recall on the track bar was rectified by the dealer by welding the nut on the track bar. Now that the nut has been welded a proper alignment can not be preformed. There is no longer adjustment available due to the welded nut. The only way to properly fix this is to replace the track bar. I have had many communications with ram (stellantis) and they refuse to remedy this as they tell me they have complied with the NTSB’s resolution.
- Service brakes
At about 3,000 miles I noticed a periodical head light flicker and intermittent radio issues. Shortly after that the truck has presented with periodical brake issues. My front brakes parodically drag and get hot. Typically on one front side or the other. However on [XXX] my wife and I took the…
At about 3,000 miles I noticed a periodical head light flicker and intermittent radio issues. Shortly after that the truck has presented with periodical brake issues. My front brakes parodically drag and get hot. Typically on one front side or the other. However on [XXX] my wife and I took the truck out for a drive and both front brakes began dragging and heated up. I had to be towed 40+ miles back home. Two of my neighbors can verify I've had issues with the brakes on multiple occasions for several years now. I've had to limp the truck home on several occasions while in town and in Feb. 2025 it put my wife and I in what a consider a dangerous situation by stranding us on the side of the highway. I don't remember any warning lamps coming on but I did a scan after I got the truck back home. B170-15, B210A-16, B222C, B2861-15, P2509 & P2560 were present. I used my scanner to delete the codes and reset the EMC but am a bit hesitant to take the truck out on the road. Note: The truck has experienced a weird and harsh vibration on back of truck as well. I stop, shut engine off - do a walk around but haven't been able to pinpoint anything. Crank engine back up and problem has seemingly resolved itself. I think it's possibly a brake issue as well. At present this truck has less than 11,000 miles on it. Yes, LOL, less than 11,000 miles. Calipers and pads are in excellent functioning order. Fluid is easily pushed back into reservoir with no restrictions and no apparent degradation of flexible lines. I considered the brake fluid might have moisture built up in the system so I had a complete fluid replacement done but problem has persisted.I did read there's a recall on the the HCU/ABS unit and my truck seems to be in that category but haven't received anything from FCA. [XXX] Your attention and assistance would be greatly appreciated. Thank You. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Electrical system
the instrument panel dash cluster went black and now I have no information like tire pressure, mph, engine oil temp, coolant temp, cruise control,parking sensor alert, ect. I have tried everything to reboot or see if there is loose connections and have come up with nothing. this could be a hazard.
- Wheels › Lugs/nuts/bolts/studs
The contact owns a 2015 Ram 3500. The contact stated while driving 60 MPH, the steering started shuddering and the vehicle made an abnormal popping sound. The contact then noticed that the front driver's side wheel was wobbling. The contact pulled over to the side of the road and inspected the…
The contact owns a 2015 Ram 3500. The contact stated while driving 60 MPH, the steering started shuddering and the vehicle made an abnormal popping sound. The contact then noticed that the front driver's side wheel was wobbling. The contact pulled over to the side of the road and inspected the wheel. The contact noticed that two of the wheel studs of the front driver's side wheel had fractured. The contact stated that the vehicle was previously taken to the dealer to be repaired under NHTSA Campaign Number: 21V398000 (Wheels); however, the dealer informed the contact that the wheel studs did not need to be replaced. The dealer was notified of the failure and informed the contact that the VIN was no longer included in the recall because the recall had been marked completed. The vehicle was not repaired and remained on the side of the road. The manufacturer was not notified of the failure. The failure mileage was approximately 166,000.
- Engine · Unknown or other
I am filing this report to highlight ongoing safety and warranty issues with my 2015 Dodge Ram 3500, which is severely impacted by Recall 67A. This recall was intended to address emissions tampering, involving significant obligations for Stellantis/Cummins Inc. under the emissions extended…
I am filing this report to highlight ongoing safety and warranty issues with my 2015 Dodge Ram 3500, which is severely impacted by Recall 67A. This recall was intended to address emissions tampering, involving significant obligations for Stellantis/Cummins Inc. under the emissions extended warranty, termed the "Special Extended Warranty." Since the completion of the recall in January 2024, my vehicle has been inoperable for a total of 148 days due to significant defects. The vehicle has required six service visits to address these issues, with the most recent visit occurring on October 31, 2024, when it was towed back to the dealership. Throughout this process, I have encountered a lack of effective communication from both Cummins and FCA, and my attempts to resolve these issues were largely ignored until I escalated the matter to federal authorities, including Randall Stone from the U.S. DOJ. The ongoing failure to address these defects has not only violated warranty obligations but also poses a risk to safety, as the vehicle remains inoperable. Impact of the Problem: The inability to use my vehicle has caused considerable disruption to my daily life, preventing me from performing essential tasks, including towing a camper and transporting heavy items. This situation has also led to significant emotional distress, given the prolonged nature of the issues and the lack of adequate responses from the manufacturer. Action Requested: I seek the NHTSA's assistance in investigating these ongoing issues with my vehicle and holding the manufacturer accountable for their failure to uphold warranty obligations and address safety concerns related to emissions defects.
- Electrical system · Service brakes · Vehicle speed control
ABS and Traction control warning lights are on display. Cruise control and 4x4 will not engage due to this issue. Also causing malfunction while towing a trailer.
- Wheels
The contact owns a 2015 Ram 3500. The contact stated while driving 35-40 MPH, the vehicle started wiggling and wobbling abnormally. The contact was able to pull to the side of the road, where he noticed that the outer rear wheel had separated from the vehicle. Additionally, the contact noticed that…
The contact owns a 2015 Ram 3500. The contact stated while driving 35-40 MPH, the vehicle started wiggling and wobbling abnormally. The contact was able to pull to the side of the road, where he noticed that the outer rear wheel had separated from the vehicle. Additionally, the contact noticed that the inner rear wheel had separated and pinched the axle, causing the wheel to support the vehicle. The vehicle was towed to the dealer, where an assessment was made. The dealer determined that the wheel studs needed be replaced under NHTSA Campaign Number: 21V398000 (Wheels); however, the wheel replacement was not covered. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 183,901.
- Power train
The contact owns a 2015 Ram 3500. The contact received notification of NHTSA Campaign Number: 17V821000 (Power Train). The contact had experienced the failure and paid for the repair before receiving the recall notification. The contact stated he received the notification in January 2024 and took…
The contact owns a 2015 Ram 3500. The contact received notification of NHTSA Campaign Number: 17V821000 (Power Train). The contact had experienced the failure and paid for the repair before receiving the recall notification. The contact stated he received the notification in January 2024 and took the vehicle, the notification, and the receipt for the repair to the dealer to be reimbursed. The contact stated the manufacturer was made aware of the issue however, the contact was not reimbursed for the repair. The failure mileage was unknown.
- Trailer hitches
The contact owns a 2015 Ram 3500. The contact stated that the gooseneck ball hitch failed to remain secured. No warning light was illuminated. The vehicle was taken to dealer. The dealer confirmed the failure with the gooseneck ball hitch was related to the recall but did not replace the gooseneck…
The contact owns a 2015 Ram 3500. The contact stated that the gooseneck ball hitch failed to remain secured. No warning light was illuminated. The vehicle was taken to dealer. The dealer confirmed the failure with the gooseneck ball hitch was related to the recall but did not replace the gooseneck ball hitch. The contact referenced NHTSA Campaign Number: 18E028000 (Trailer Hitches) as a possible solution however, the VIN was not included in the recall. The manufacturer was notified of the failure. The failure mileage was approximately 37,000.
- Unknown or other
Backing up 11/20/23 in our driveway, the tailgate fell down, shut it and it occurred 2 more times before it could be re-parked.
- Service brakes
ABS Module / HCU (Hydraulic Control Unit Failure) causing abs MIL on. Fault code C0020
- Power train
The contact owns a 2015 Ram 3500. The contact stated that after his wife started the vehicle, the transmission failed to shift into the intended gear because the gear shifter was loose. The vehicle was towed to the dealer, where the gear shifter bolt was tightened; however, after the repair was…
The contact owns a 2015 Ram 3500. The contact stated that after his wife started the vehicle, the transmission failed to shift into the intended gear because the gear shifter was loose. The vehicle was towed to the dealer, where the gear shifter bolt was tightened; however, after the repair was performed, the gear shifter detached while the contact was shifting into gear. The vehicle was not repaired. The manufacturer was made aware of the failure. The contact stated that the vehicle was previously repaired under NHTSA Campaign Number: 17V821000 (Power Train); however, the failure occurred. The failure mileage was approximately 112,000.
- Wheels
The contact owns a 2015 Ram 3500. The contact stated while driving at approximately 30 MPH, the driver's front and driver's side rear wheels detached from the vehicle. The contact became aware of nine broken wheel studs. There was no warning light illuminated. The contact referenced the failure to…
The contact owns a 2015 Ram 3500. The contact stated while driving at approximately 30 MPH, the driver's front and driver's side rear wheels detached from the vehicle. The contact became aware of nine broken wheel studs. There was no warning light illuminated. The contact referenced the failure to NHTSA Campaign Number: 21V398000 (Wheels) however, the VIN was not included in the recall. The contact made a local dealer aware of the failure and confirmed that the VIN was not included in the recall. The vehicle was towed to an independent mechanic to be diagnosed. The contact was informed that the wheel studs and lug nuts needed to be replaced. The vehicle remained with the independent mechanic awaiting parts for the repair. The manufacturer was made aware of the failure. The approximate failure mileage was 110,000.
- Service brakes
ABS Module failed and is not reading rear wheel speed. Shop isolated issue to ABS module, and hydraulic control unit. Four safety components are no longer working as a result: ABS braking, traction control, 4wd, and rear back up sensors. This appears to be a common issue with Rams HD trucks as the parts are on back order causing me to drive my vehicle with no safety features.
- Air bags · Electrical system · Structure › Body
Driving down turnpike my truck went up in flames, mopar sent investigator to determine cause of fire at dealership never called me to give me a report they emailed me to badly burnt to determine cause of fire.
- Service brakes · Unknown or other
After I brought my truck in for recall Y26 they inspected the studs and said they were fine (not stretched which is what the recall is for). I took a trip and put 6,700 after the inspection and the dealer re-torqued the wheels. When I got back there seemed to be something wrong with the brakes…
After I brought my truck in for recall Y26 they inspected the studs and said they were fine (not stretched which is what the recall is for). I took a trip and put 6,700 after the inspection and the dealer re-torqued the wheels. When I got back there seemed to be something wrong with the brakes and so I brought it back to the same dealer that inspected it before and verified the studs were not stretched, now found that the pads and rotors were damaged and the studs were studs now stretched. No problem before the recall but after the recall and new torque for the wheels the studs are stretched. Dodge said they will pay for the studs to be replaced but not the brakes. The brakes were fine before. If it were just the pads I would understand that this could be normal wear but the rotors being destroyed only on the wheels that now had stretched studs does not make any sense and given that it was inspected beforehand and only after the new torque did the studs stretch and damage the rotors it seems like they may not be fixing the issue that the recall was originally issued for, in fact, they may have made the problem worse. The representative from Dodge said they have not had any other complaints so the brake damage must not have been caused by the stretched studs.
- Wheels › Lugs/nuts/bolts/studs
The contact owns a 2015 Ram 3500. The contact had initially received notification of NHTSA Campaign Number: 21V398000 (Wheels). The vehicle was then taken to a dealer where the recall repair was performed. The contact stated that approximately 6,600 miles after the recall repair was performed, the…
The contact owns a 2015 Ram 3500. The contact had initially received notification of NHTSA Campaign Number: 21V398000 (Wheels). The vehicle was then taken to a dealer where the recall repair was performed. The contact stated that approximately 6,600 miles after the recall repair was performed, the vehicle started vibrating while driving at various speeds. Additionally, the contact mentioned that the brake pedal was vibrating while depressed. There was no warning light illuminated. Upon inspection, the contact discovered that all the lug nuts on each wheel were not properly tightened. The dealer and the manufacturer were notified of the failure. The vehicle was not repaired. The failure mileage was approximately 131,000.
- Wheels
Informed on recall for a wheel stud possibly breaking sending wheel flying off vehicle. 7 months later and no fix!! This could be a deadly occurence if wheel comes off vehicle and hits another vehicle as well as loss of control of my vehicle. I also tow 16000lb trailers!
- Steering
Drag link was tack welded by dealer as a temporary fix but will not replace it with the upgrade. I cannot get a wheel alignment unless I purchase a new drag link for 450.00 dollars
- Steering · Suspension
I was towing my travel trailer and entered a slight left turn at approximately 50mph when my front driver side tire started to shake/wobble uncontrollably. I slowed down and it stopped. Dealership replaced both front hubs and bearings. When I hit a small bump while turning and not towing, it still…
I was towing my travel trailer and entered a slight left turn at approximately 50mph when my front driver side tire started to shake/wobble uncontrollably. I slowed down and it stopped. Dealership replaced both front hubs and bearings. When I hit a small bump while turning and not towing, it still shakes/wobbles uncontrollably. I notified dealership about it and they still failed to make the repair. The vehicle IS still under warranty.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Post Recall Remedy Brake Transmission Shift Interlock (BTSI) Failure
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models…
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V-821 or 18V-100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V-821 and 18V-100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
- Steering loss due to linkage separation
On December 17, 2018, NHTSA's Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18016 to investigate alleged drag link failures in the steering system on model year (MY) 2015 and 2016 Ram 2500 trucks manufactured by FCA US, LLC (FCA). The drag link failures were found to be due to a safety defect…
On December 17, 2018, NHTSA's Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18016 to investigate alleged drag link failures in the steering system on model year (MY) 2015 and 2016 Ram 2500 trucks manufactured by FCA US, LLC (FCA). The drag link failures were found to be due to a safety defect with the steering linkage where the drag link adjustable connector (used to adjust the steering system), held in position by two opposing jam nuts, can loosen. The loosening of this part can lead to wear and deterioration of the threads and eventual separation of the drag link, causing loss of steering. During the course of PE18016, it was found that two styles of drag link were used by FCA on the subject vehicles. The subject vehicles consist of two drivetrain types including four-wheel drive (4WD) and two-wheel drive (2WD). The 4WD and 2WD trucks used drag links of differing design but both incorporated the same threaded connector. In January 2019 FCA issued recall 19V-021 to address a potential loss of steering control in certain Model Year (MY) 2013-2018 4WD RAM 2500 and 3500 trucks. The trucks using the 2WD style drag link were not included in the scope of recall 19V-021. ODI upgraded PE18016 to an Engineering Analysis EA19004 on December 12, 2019. The purpose of EA19004 was to investigate if the root cause of the safety defect addressed by recall 19V-201 also affected the 2WD trucks and evaluate FCA’s rationale for not including them. ODI also monitored incoming consumer complaints regarding the remedy associated with 19V-021 and evaluated the suitability and long-term effectiveness of the prescribed repair. In the Defect Information Report submitted for recall 19V-021, FCA stated that the outboard jam nut could loosen and result in damage to the threading of the steering drag link connector. This could cause a separation in the drag link resulting in a loss of steering control. FCA determined that only the 4WD style drag link was affected and did not recall trucks with the 2WD style drag link due to design differences that made it unsusceptible to this failure mode. The repair remedy called for the steering coupler to be tightened to the proper torque prior to the jam nut being spot welded to the coupler body. If the coupler has already become detached or correct torque cannot be obtained, the drag link is to be replaced with an updated unit that went into production on the MY2019 RAM trucks.This updated unit uses a clamp to secure the coupler in place of the jam nuts used on original style components. In order to determine if the 2WD drag link was susceptible to the same defect found on the 4WD vehicles, ODI requested that our Vehicle Research and Test Center (VRTC) conduct testing on both RAM 2500 4WD and 2WD trucks. This testing was to determine operating conditions that might lead to loosened jam nuts of the recalled 4WD design and recreate these conditions on the 2WD vehicles to discover whether the 2WD design would also experience the loosening defect. Results from VRTC’s dynamic testing indicated that when the jam nuts are significantly under-torqued, they may loosen further from regular vehicle operation on the 4WD vehicles. Further, VRTC testing does not refute FCA’s assertion that the failure mechanism does not exist in the 2WD steering system. At the time of this closing resume, ODI has only received two allegations of drag link separation on 2WDvehicles.Neither could be validated as resulting from loose jam nuts. Since the release of recall 19V-021 ODI has received consumer complaints regarding the appearance of the spot weld applied to the defective drag link and the inability to have the steering properly aligned after welding of the jam nut. In September 2023, FCA provided owners with a supplemental Vehicle Alignment Clarification notification that provided information on an updated alignment procedure. Regarding the spot weld remedy used on the 4WD vehicles, ODI is concerned about the remedy in that during an alignment by a non-dealer repair facility, the spot weld might not be replaced after the alignment. To date there is no complaint trend of post alignment drag link separations, weld failures or other safety related incidents on remedied vehicles. This investigation is being closed with no further action. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances.
- Steering loss due to linkage separation
On December 17, 2018, NHTSA's Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 18-016 to investigate the steering system on model year (MY) 2015 and 2016 Ram 2500 manufactured by FCA US, LLC (FCA). Four complaints were received alleging separation of the drag link, a steering linkage that…
On December 17, 2018, NHTSA's Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 18-016 to investigate the steering system on model year (MY) 2015 and 2016 Ram 2500 manufactured by FCA US, LLC (FCA). Four complaints were received alleging separation of the drag link, a steering linkage that connects between the right front steering knuckle and the pitman arm on the steering box output shaft. The failures were found to be at a threaded coupler within the drag link used for adjusting the length of the linkage during routine maintenance (alignment) of the steering system.Once separation occurs, turning the steering wheel has no effect, and there is no way for the driver to control or maintain the direction of the vehicle. During the investigation, it was determined that the same threaded coupler was used on two different drag link designs FCA manufactured on MY 2013-2018 Ram 2500 and 3500 pickups. FCA refers to the designs as either 4x2 or 4x4 style. In both designs, the coupler is prevented from turning on the drag link via two jam nuts that are tightened against the coupler. In its response to NHTSA's March 15, 2019, Information Request (IR) letter, FCA identified 48 incidents alleging separation of the steering linkage at the coupler resulting in a loss of steering control. Of those, 13 involved a crash, one of which resulted in an injury. All of the separations involved the 4x4 style drag link. Additionally, FCA's IR response refers to over 300 4x4 style equipped vehicles that experienced, or may have experienced loosening of one or more coupler jam nuts. On January 25, 2019, FCA submitted a Defect Information Report (DIR) initiating NHTSA Recall No. 19V-021. In its DIR, FCA stated that the outboard jam nut in certain MY 2013-2018 Ram 2500 and 3500 could loosen potentially resulting in damage to the coupler and/or drag link threading allowing one end of the drag link to separate. The DIR notes that drag link separation results in loss of steering control, which in turn can cause a crash without warning. FCA's DIR did not identify a root cause for the defect, however it posits that an improperly torqued outboard jam nut could loosen, and with long-term vehicle use, cause damage to the outer link bar and/or coupler threads due to relative motion between the two components. The scope of Recall 19V-021 included vehicles with the 4x4 style drag link only. Also discussed in its IR response, FCA noted that the 4x2 style drag link contains a design difference (the outboard portion of the drag link is straight while the 4x4 style contains a bend) which it suggests may result in differences in the mechanical (bending) loads presented at the coupler and jam nut interface. Moreover, the DIR states that While root cause of the 4x4 style defect has not been established, FCA US believes that bending loads on the drag link is, at least, a causal contributing factor. FCA notes it did not identify any reports alleging 4x2 style separation as well as only three reports of loosening of jam nuts, two of which resulted in loosening that provided obvious warning to the vehicle operator, indicating a different failure mode.NHTSA is upgrading this investigation to Engineering Analysis (EA) 19-004 in order to continue to monitor the subject 4x2 style vehicles for evidence of field failures. Additionally, in conjunction with NHTSA's Vehicle Research and Test Center, ODI intends to more thoroughly study potential root cause(s) of the 4x4 style defect mechanism, and if identified, will seek to determine if the 4x2 drag link is susceptible to the same mechanism(s). NHTSA will also evaluate the long-term suitability of the recall
- Software security vulnerability
On July 23, 2015, Fiat Chrysler Automobiles (FCA) launched Safety Recall 15V-461 to remedy security vulnerabilities in approximately 1.4 million model year (MY) 2013 through 2015 vehicles equipped with Uconnect head units (HU) 8.4A (RA3 radio) and 8.4AN (RA4 radio) manufactured by Harman International.On July 24…
On July 23, 2015, Fiat Chrysler Automobiles (FCA) launched Safety Recall 15V-461 to remedy security vulnerabilities in approximately 1.4 million model year (MY) 2013 through 2015 vehicles equipped with Uconnect head units (HU) 8.4A (RA3 radio) and 8.4AN (RA4 radio) manufactured by Harman International.On July 24, 2015, the Office of Defects Investigation (ODI) opened Recall Query, RQ 15-004, to investigate HU security vulnerabilities and remedy effectiveness in the recalled population and to determine whether similar units have been supplied for use in other FCA vehicles.In an August 11, 2015 letter, FCA submitted a second Part 573 safety recall report expanding the scope of the Uconnect RA4 model radio to include additional 7,810 MY 2015 Jeep Renegade vehicles manufactured from September 18, 2014 through June 25, 2015 (Recall 15V-508).Scope analysis indicated that Uconnect radios installed in FCA vehicles not included in recalls 15V-461 or 15V-508 (subject recalls) are not equipped with built-in cellular access or short range wireless communication features and, thus, do not contain the security vulnerabilities addressed by the subject recalls. SUBJECT VEHICLES: MY2014 through 2015 Dodge Durango, Jeep Grand Cherokee and Jeep Cherokee sport utility vehicles; MY2013 through 2015 Ram 1500, 2500, 3500 and 4500/5500 pickup trucks; MY2013 through 2015 Dodge Viper vehicles; and MY2015 Chrysler 200, 300, Jeep Renegade, Dodge Charger and Challenger vehicles.According to FCA, long and short range wireless vulnerabilities identified in the recalled vehicles could allow unauthorized third-party access to, and manipulation of, networked vehicle control systems.Successful exploitation of the vulnerabilities, coupled with reverse engineering of networked microprocessor control modules, could result in unauthorized manipulation of vehicle control systems. This unauthorized manipulation of vehicle controls and systems could expose the driver, vehicle occupants or other highway users to an increased risk of injury.FCA and its network provider, Sprint, conducted a nationwide campaign to block access to a radio communications port that was unintentionally left open.On July 27, 2015, short range wireless vulnerabilities were also blocked.Finally, third party security evaluation and regression testing identified vulnerabilities that were either remedied by Sprint or through updates to the FCA Uconnect software.ODI identified a total of 30 complaints or field reports on unique vehicles submitted by FCA (29) or received by NHTSA (1) alleging incidents of theft from a vehicle or anomalous performance that the owner alleged were caused by, or may have been caused by, remote hacking.Twenty-six (87%) of these reports were submitted after a magazine article was published on July 21, 2015, describing the remote hacking of an FCA vehicle by researchers who were able to affect the operation of various vehicle control systems, including the service brakes, steering, throttle and ignition.Most of the complaints involved vehicle systems that were not safety critical (e.g., complaints related to radio, navigation system, or air-conditioning control) and did not affect vehicle control.Three complaints reported engine stalls.One owner reported sudden unintended acceleration allegedly related to hacking.None of the complaints or field reports reviewed involved the steering and braking vehicle control effects demonstrated by the research hackers prior to the recall.There were no confirmed incidents of hacking in any of the records reviewed by ODI.The remedies completed by Sprint and FCA appear to have eliminated vulnerabilities that mi
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010205Plate - Planetary
- 11002737Emission Recall 67A D Truck Engine Calibration
- 11002526EMISSION RECALL 67A D Truck Engine Calibration
- 11001134"6.7L Diesel Emissions Warranty Extension XQ1 Special Warranty Extension"
- 11001125"6.7L Diesel Emissions Warranty Extension XQ1 Special Warranty Extension"
- 11001049Warranty Bulletin D-24-10 (XQ1) Emission Control System Components Select 2013 - 2019 RAM 2500 Pickup (DJ) and 2013- 2019 RAM 3500 Pickup (D2)
- 11001020On Board Diagnosis (OBD) Monitor Readiness Information
- 10251812Emission Recall 67A D Truck Engine Calibration
- 10251783Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
- 10248914Emission Recall 67A - D Truck Engine Calibration
- 10248846Steering Drag Link If drag link had been welded due to V06 recall repair and there is an alignment concern, prior to drag link replacement ensure that the welded draglink toe setting procedure has been followed first. ~ ~ Service Library: 02 - Front Suspension / Wheel Alignment / Standard Procedure / TOE SETTING PROCEDURE FOR TRUCKS WITH DRAG LINK RECALL WELD ~
- 10248594Emissions Recall 06A - Vehicle Emission Control Information Label
- 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10244433Emissions Recall 06A - Vehicle Emission Control Information Label
- 10244356LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
- 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10243209FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
- 10243208Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
- 102427956.7L New Oil Usage Information Incorrect oil used. This bulletin provides information regarding the correct oil grade to use on the 6.7L Cummins used in the 2023 to 2013 HD Trucks. The following information is intended to eliminate confusion.
- 10242717Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
- 10239957Water Quality When Mixed With Engine Coolant
- 10236933wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
- 10234420Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
- 1023202166RFE Transmission Slip Under High Engine Load And Premature Wear
- 10231978Uconnect Access Buttons On The Rear View Mirror Are Inoperative
- 10231735Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
- 10231712Malfunction Indicator Lamp (MIL) Illumination. NOx Sensor Diagnostic Trouble Codes (DTCs) Diagnosis Information.
- 10230343Cummins 6.7L Turbocharger Actuator - X99 Warranty Extension This bulletin involves replacing the turbocharger actuator. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technicianmay find that one or more of the following DTCs have been set: U010C - Lost Communication With Turbocharger/Supercharger Control Module. P003A - Turbocharger Boost Control Module Position Exceeded Learning Limit. P00AF - Turbocharger Boost Control Module Performance. P0046 - Turbocharger Boost Control Circuit Performance.
- 10230189Left Hand Drivers Side Mirror Takes Longer to Defrost Or Clear Than Right Side Passenger
- 10230183No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
- 10230180Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
- 10229993NUT, Wheel Flange Wheel Nut Service Torque should be 175 N-M.
- 10229988NUT, Wheel Flange Wheel Nut Service Torque should be 190 N-M.
- 102299516.7L Diagnostic And System Improvements
- 10229920RA3 RA4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. Radio may display previous cameras image before displaying the current image.
- 10229890RA2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud (Grand Cherokee only). U0208-00 - Loss Communication With Heated Seat Control Module (Cherokee only).Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.
- 10229888RG2 Or RJ2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud. The radio does not allow selection of the Polish language. The radio fan continually runs at high speed. Customer perception may be the radio fan is too loud.Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.
- 10229572Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
- 10229454Cooler - egr
- 102293416.7L New Oil Usage Information This bulletin provides information regarding the correct oil grade to use on the 6.7L Cummins used in the 2019 and newer HD Trucks. The following information is intended to eliminate confusion.
Every RAM 3500 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.