2020 Van Hool CX45

Recalls

2 recalls name the 2020 Van Hool CX45. Newest first.

• Visibility › Glass, side/rear

  Mar 26, 2026NHTSA 26V1910006,994 vehicles

  ABC BUS Inc is recalling certain 1999-2013 Van Hool C2045, 2004-2013 Van Hool T2145, 2013-2022 Van Hool TX45, 2013-2023 Van Hool CX45, and 2016-2022 Van Hool CX35 vehicles. The front entrance door may have the incorrect glaze on the lower curb view window. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard…

  Risk and remedy

  Risk

  The incorrect glaze may reduce the driver's visibility, increasing the risk of a crash.

  Remedy

  Dealers will inspect and install a nontransparent vinyl cover over the window as necessary, free of charge. Owner notification letters were mailed April 20, 2026. Owners may contact ABC Bus customer service at 1-877-427-7278. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning April 30, 2026.

  Full recall details →

• Fuel system, diesel › Fuel injection system › Fuel rail

  Dec 20, 2021NHTSA 21V995000139 vehicles

  Van Hool N.V. (Van Hool) is recalling certain 2020-2021 CX45, TX45, and 2021 TDX25 vehicles. The fuel tubes between the fuel rail and the injectors for cylinders four, five, and six may fatigue and crack, which can result in a high pressure fuel leak.

  Risk and remedy

  Risk

  A high pressure fuel leak in the presence of an ignition source can increase the risk of a fire.

  Remedy

  Cummins dealers will replace the fuel tubes, and install vibration isolators, free of charge. Interim owner notification letters were mailed January 28, 2022. Owner notification letters were mailed on March 11, 2022. Owners may contact Cummins customer service at 1-800-286-6467. Van Hool's number for this recall is P1556-SB2095.

  Full recall details →

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010424This service bulletin provides you with information about the location of emergency side window decals so that the vehicle meets the National Highway Traffic Safety Administrations (NHTSA) Federal Motor Vehicle Safety Standards (FMVSS) in the U.S and the Canadian Motor Vehicle Safety Standards (CMVSS) in Canada about this subject.
• 10250324an Hool feels very strongly about quality and constantly focuses on product improvement. This is why we would like to ask you to provide us with the correct information as quickly as possible when filing a warranty request. A fully documented diagnostic is key in this process. The more precise and complete the supplied information is, the quicker we can finalize your request, with financial compensation when applicable. For this reason, follow the procedure below as closely as possible
• 10248730This service bulletin provides you with information about the location of emergency side window decals so that the vehicle meets the National Highway Traffic Safety Administrations (NHTSA) Federal Motor Vehicle Safety Standards (FMVSS) in the U.S and the Canadian Motor Vehicle Safety Standards (CMVSS) in Canada about this subject.
• 10247503DESCRIPTION Van Hool has been informed about a harmless phenomenon regarding the front entrance door when the air suspension raising system is activated. Investigation has shown that when the raising system is activated, air is pulled out of the front passenger compressedair circuit causing the quick release valve in that circuit to a momentary switch. This can be noticed by a short soft sound of escaping air. This service bulletin gives step-by-step instructions how to install an additional singlecheck valve to prevent this phenomenon from happening.
• 10244199DESCRIPTION: Van Hool has determined that some of the seven fasteners securing the automatic belt tensioner base plate are subject to slackening. Tests have shown that these fasteners must be installed with Loctite 243 and tightened to a torque of 90 10 Nm (65 7 ft.lbf). To address this issue, Van Hool is conducting a field change program whereby the seven fasteners must be removed and checked one by one for length and thread pitch (1.75 mm). What to do next is explained in this service bulletin
• 10242220SUBJECT : Engine overheating due to an open or not properly closed access door with electric cooling fans CONDITIONS : This service bulletin does not entitle to any reimbursement. Your vehicle is equipped with electric cooling fans located at the inside of the access doors of the radiator and charge-air cooler compartment. To prevent personal injury due to running fans, a safety system with proximity switches prevents the cooling fans from running when the access door is open or not properly closed. The cooling system will in that case not operate causing possible overheating of the engine when this situation continues for a longer time. To prevent this from happening, it is important to follow the guideline below:
• 10237604Van Hool has introduced in production a lower value resistor in the defroster fan speed control circuit to improve windshield demisting. Customers who want to install this resistor can follow the step-by-step instructions mentioned in this service bulletin.
• 10235083Incorrect position of high-pressure switch and test connection on refrigerant compressor discharge service valve Van Hool has determined that the position of the high-pressure switch and the test connection on the refrigerant compressor discharge service valve has been incorrectly placed during the assembly process. The result is that the high-pressure protection system of the refrigerant circuit is not working when the discharge valve is in its normal running position (refer to figure 3 for service valve positions). To address this issue, Van Hool is conducting a field change program, the terms and conditions of which are explained further on under Warranty. Owners and operators of the affected units should first check the position of the high-pressure switch and, if necessary, modify the placement.
• 10233467Service Information: In its production process, Bock, manufacturer of refrigerant compressors, has switched to a new type of motor protection switch for the electric motor of the refrigerant compressor. As the MP10 motor protection switch (VH11472802) is no longer made available as a spare part, as of now you will receive the new INT69G motor protection switch (VH11691810) when ordering. The MP10 and the INT69G are interchangeable, but fastening and electric connection are different.
• 10219652Product Improvement: ALL VEHICLES WITH LIGHT-ALLOY WHEELS - Introduction of wheel-end monitoring system (WEM). Van Hool has released a wheel-end monitoring system (WEM) which can be installed on all vehicles equipped with light-alloy wheels. The WEM is installed at the outboard side of the wheel and monitors vibrations produced by the wheel bearing. It warns in case of bearing raceway spalling by flashing a red LED on the unit. The WEM is delivered with a magnet which is used to change from "transport" to "standstill" mode.
• 10210015Service Information: Removal and installation of Shaw DEF tank sensor unit The purpose of this service information bulletin is to inform you about the removal and installation of a Shaw DEF tank sensor unit.
• 10209999Product Improvement: Introduction of new mounting bracket for magnet on engine compartment rear door (starting inhibition system) Van Hool has released an improved mounting bracket for magnet of the starting inhibition system. The starting inhibition system prevents engine starting from the dashboard when the engine compartment rear door is not closed. Instead of the previous bracket, the new bracket is made of stainless steel, larger and thicker which makes it more reliable on the long run.
• 10209998Product Improvement: Introduction of new generation DEF tank sensor unit Some previous manufactured DEF tank sensor units are no longer available as spare part. This service bulletin gives you information about the visual points of difference between the generations and which one to order in case of replacement. Most of the replacements are direct fit, except for the sensor units with an asterisk in the table which must be secured with a split mounting ring consisting of two halves instead of the original closed mounting ring.
• 10209996Field Change Program: Check refrigerant compressor wiring A rubber protection will be added at the top of the plate that holds the connectors. Missing plug seals will be added to the back of the 4-pin connector and the missing connector socket to the open connector on the compressor as well. Check for corrosion, bad pins should be replaced.
• 10209994Service Information - Introduction of new 4/2 solenoid valve in compressed-air circuit Van Hool has switched over into production to a new type of 4/2 solenoid valve in the compressed-air system. As the previous Knorr-Bremse (Bosch) solenoid valve (VH11102170) is no longer made available as spare part, customers will receive a Wabco solenoid valve (VH660526759) when ordering. Both valves are interchangeable, but some differences must be considered. Consult the information in this service bulletin for a proper installation.
• 10209992Service Information - Maintenance operations related to refrigerant compressor oil This service information bulletin is a reminder/update about refrigerant compressor oil maintenance. To ensure a reliable system, it is important to perform the maintenance on a regular base as mentioned further on.
• 10209989Field Change Program: Optimization of driver's cab climate control system operation Van Hool is conducting a Field Change Program at which the original temperature sensor will be disconnected, and a new one will be installed.
• 10206913To change condenser fan relay 660752034 by relay 660762200.
• 10206912To check anchorage of passenger seats.
• 10201570SERVICE INFORMATION BULLETIN: Van Hool has switched over into production to a new type of 4/2 solenoid valve in the compressed-air system. As the previous Knorr-Bremse (Bosch) solenoid valve (VH11102170) is no longer made available as spare part, you will receive a Wabco solenoid valve (VH660526759) when ordering. Both valves are interchangeable, but some differences must be considered. Consult the information in this service bulletin for a proper installation.
• 10190134Service Information Bulletin: What to do in case of prolonged vehicle standstill. This service bulletin provides an overview of works to be performed during prolonged vehicle standstill.
• 10185031Product Improvement Bulletin: As from the following units onwards (CX35, MY2020:49983; CX45, MY2020: 81456; TX45, MY2020: 41718), vehicles are factory fitted with a FT6000SC circulating pump instead of the previously installed FT5000 circulating pump.
• 10185027Product Improvement Service Bulletin: To retrofit with Adaptive Cruise Control (ACC) and Collision Mitigation System (CMS) Van Hool has released ACC in combination with CMS as an option
• 10185026Work Procedure: To load new program and parameters into digital instrument panel (MVP) (Informative)
• 10185005Work Procedure: To retrofit with Collision Mitigation System (CMS) and Adaptive Cruise Control (ACC). ADDENDUM TO SERVICE BULLETIN SB1789: This work procedure should be read together with service bulletin SB1789.
• 10185002Work Procedure: To set odometer reading (Informative)
• 10183573Product Improvement Bulletin: As from the following units onwards (CX35, MY2020: 49983; CX45, MY2020: 81456; TX45, MY2020: 41718), vehicles are factory fitted with a FT6000SC circulating pump instead of the previously installed FT5000 circulating pump.
• 10182687Service information Bulletin: Stress-free installation of flex pipe This service bulletin gives step-by-step instructions on how to install the flex pipe properly. The flexible part of the flex pipe handles thermal expansion and engine vibration, and is prone to premature breakdown in case of incorrect installation.
• 10180761Van Hool has received some complaints about the temperature control in the drivers cab. Investigation has shown that these vehicles have left the factory with a drivers cab climate control unit outlet temperature sensor that is not compatible with the dash control unit. To address this issue, Van Hool is conducting a Field Change Program at which the original temperature sensor will be disconnected, and a new one will be installed.
• 10179511Van Hool N.V. and ABC Companies did not release any new service bulletins during the month of August 2020.
• 10176935Service Information Bulletin: The purpose of this bulletin is to inform you about how to align the cooling fan drive. This should be performed every time components of the fan drive have been removed, and when evidence of contact damage has been noticed on fan or shroud.
• 10174983Service Information: he purpose of this service bulletin is to inform you about the innocent traces of lubricant at the bottom of the transmission bell housing on new vehicles. They are caused by the protective anti-corrosion coating at the inside of the bell housing which becomes liquid at transmission operating temperature. This phenomenon is temporarily and no indication that there is a sealing problem! The lubricant can easily be removed with ordinary cleaning product.
• 10174982Service Information: This bulletin is being released as a reminder of the importance of wheel bearing preventive maintenance. Check the wheel bearing end-play every 50,000 miles*, and when having any work done on the brakes or any other component on the axle end.
• 10170879To replace alternators in CX45 and TX45 with Cummins X12 engine. This work procedure is applicable to vehicles with Cummins X12 engine.
• 10170878To replace windshield wiper motor. This work procedure gives step-by-step instructions about replacing the windshield wiper motor on CX45's.
• 10169675Introduction of a DEF tank filler cap unit with integrated de-aeration valve. Van Hool has switched over to a new type of DEF tank filler cap unit from MY2020 vehicles onwards. The new DEF tank filler cap unit is equipped with an integrated de-aeration valve and prevents tank ventilation problems in case the standard installed tank in-line de-aeration valve is clogged due to DEF crystallization. The new DEF tank filler cap unit fits earlier vehciles and will be supplied as kit 91082547.
• 10168609To modify electrical supply for regeneration buttons. Van Hool has been informed by ABC about a problem with the electrical supply of the regeneration buttons located on the control panel in the engine compartment. To address this issue, ABC Companies should modify the above mentioned vehicles before delivery according to the step-by-step instructions mentioned in this work procedure.
• 10168579Product Improvement. Introduction of new single check valves in cooling-circuits deaeration lines.Van Hool have recently switched over into production a new type of single check valve. Contrary to the previous type equipped with a plastic housing, the new type comprises an aluminium housing. Because of this, they are better suited to resist higher coolant temperatures. As the new type can also be used on previoulsy sold vehicles, only the new type will be available as a spare part. This service bulletin applies to All Van Hool Vehicles.
• 10166961Optimization of instrument panel wake-up circuit. Van Hool has found a problem in the wake-up process of the new digital instrument panel. To address this issue, ABC Companies should modify the above mentioned vehicles before delivery according to the step-by-step instructions in this work procedure.
• 10166960Replacement of pull-down resistors in interior lighting circuit. Van Hool has noticed a problem with the heat dissipation of the pull-down resistors used in the interior lighting electrical circuits. To address this issue, ABC Companies should modify the above mentioned vehicles before delivery according to the step-by-step instructions mentioned in this work procedure.

Every Van Hool CX45 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.