2006 Chrysler Pacifica
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Chrysler › Pacifica › 2006
These records cover every 2006 Chrysler Pacifica. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
1 recall names the 2006 Chrysler Pacifica. Newest first.
On certain passenger vehicles, the fuel pump module and the power train control module (pcm) software may allow the engine to stall under certain operating conditions.
Risk and remedy
Risk
This could cause a crash to occur without prior warning.
Remedy
Dealers will reprogram the power train control module. The fuel pump module will also be replaced on vehicles built from august 1, 2004 through september 30, 2004. the recall began on november 21, 2006. owners may contact daimlerchrysler at 1-800-853-1403.
Owner complaints
726 complaints20 involved a crash7 involved a fire24 injuries10 deaths
What owners report most
Latest complaints
- Engine · Fuel system, gasoline · Power train
The contact owns a 2006 Chrysler Pacifica. The contact stated that while driving at various speeds, the vehicle turned off independently but was able to be restarted. Additionally, the vehicle was difficult to start. The vehicle was taken to an independent shop, where the PCM was reprogrammed and…
The contact owns a 2006 Chrysler Pacifica. The contact stated that while driving at various speeds, the vehicle turned off independently but was able to be restarted. Additionally, the vehicle was difficult to start. The vehicle was taken to an independent shop, where the PCM was reprogrammed and an unknown fuel injector repair was performed; however, the failure recurred. The contact stated that while at a complete stop, the vehicle shut off independently but was able to be restarted. The check engine warning light was illuminated. The contact stated that upon taking the vehicle to the dealer for the recall repair of NHTSA Campaign Number: 06V432000 (Power Train), the dealer informed the contact that the equipment and parts to do the recall repair were not available after the vehicle had remained at the dealer for two days. The contact stated that several other dealers were contacted and provided the same information. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 94,791.
- Seats
When struck from behind in an accident, the driver's front seat failed.
- Equipment adaptive/mobility › Vehicle controls › Speed control
The contact owned a 2006 Chrysler Pacifica. The contact stated that while driving at 35 MPH, she lost control of the vehicle as it went through a guardrail and crashed into a tree where it came to a stop. The contact stated that she lost consciousness as she could not remember went occurred in…
The contact owned a 2006 Chrysler Pacifica. The contact stated that while driving at 35 MPH, she lost control of the vehicle as it went through a guardrail and crashed into a tree where it came to a stop. The contact stated that she lost consciousness as she could not remember went occurred in detail. A professional removed her from the vehicle. The contact sustained head and neck injuries. The contact stated that she went to the hospital after the incident. The contact stated that a police report was filed. The vehicle was towed from the scene and later deemed a total loss. The failure cause was not diagnosed by an independent mechanic or dealer. The manufacturer was not contacted. The failure mileage was 102,000.
- Unknown or other
Bought this car 3 months ago from Ford dealership, took it to mechanic shop today for oil change and was told car is "unsafe to drive" from frame being so rusted
- Unknown or other
Bought car from a private seller and wasn't informed of MASSIVE and UNSAFE DAMAGE TO ENGINE CRADLE. The engine cradle is nearly completely rotted out. Don't know if rust has eroded other parts until a mechanic can look extensively at the engine cradle. I have been trying salvage yards and 9 out…
Bought car from a private seller and wasn't informed of MASSIVE and UNSAFE DAMAGE TO ENGINE CRADLE. The engine cradle is nearly completely rotted out. Don't know if rust has eroded other parts until a mechanic can look extensively at the engine cradle. I have been trying salvage yards and 9 out of the 10 Pacifica's I have inquired about the engine cradle is rotted beyond repair. It has to be replaced. The fee for replacing and labor is going to be anywhere from $400 to $2500. and the vehicle has only 153÷k on it. This is a huge and reoccurring issue with the Chrysler Pacifica after I did research.
- Power train
I got in the car started it as usual, shifted it in (D), pulled out of my church parking lot, got about 5 miles away from my church stopped at a red light. The light turned green I accelerated as usual. At this light is a slight incline about 15% ways up the incline it just stopped pulling. I…
I got in the car started it as usual, shifted it in (D), pulled out of my church parking lot, got about 5 miles away from my church stopped at a red light. The light turned green I accelerated as usual. At this light is a slight incline about 15% ways up the incline it just stopped pulling. I pressed the gas heat the engine Rev but no power to the wheels. So I shifted it in auto stick mode and it wouldn’t change out of second gear I left it on the highway for about 3 days.I went back trying to reset the trans by turning the switch on and holding the gas pedal for 30sec as seen in Chryslers forum and YouTube yet still no power had the car towed back to Alabama when I go to church in Tennessee which was about 50 miles away or so. Get it home after paying a huge towing bill. Because my insurance only covered like 15miles. I got it home try to shift it in R, D, and The Autostick. however, it finally started going back to 1st gear. Unfortunately it still wouldn’t pull. I’ve looked up the problem and there is a recall for this, However when I call Chrysler it doesn’t cover my vehicle
- Power train · Unknown or other
Vehicle shut off WHILE DRIVING ON THE ROAD out of nowhere after running perfectly fine and since this incident the car won't start at all. Had the car diagnosed and it said it's the "Transmission control module"
- Structure › Body
A few weeks ago we took our car to a mechanic to have the brakes worked on as a part of routine maintenance. When we picked it up, he noted that when he had it up on the lift, he saw that the engine cradle was very badly rusted. He said that we shouldn't drive it anymore because of the risks…
A few weeks ago we took our car to a mechanic to have the brakes worked on as a part of routine maintenance. When we picked it up, he noted that when he had it up on the lift, he saw that the engine cradle was very badly rusted. He said that we shouldn't drive it anymore because of the risks involved. I tried to crawl under the car when we got home (there isn't a ton of clearance) but I saw what he was talking about. At that point we looked online and found hundreds and hundreds of similar experiences and complaints. We were left dumbfounded at the risks this introduces...thinking about what would happen if this mechanic hadn't noticed the issue and we'd been driving down the interstate with our kids when the thing decided to give way. And the fact that the manufacturer knows of this issue and has done nothing is beyond disgusting. Fortunately we found out from the mechanic, not from the engine falling out. Even still, this means that we're left with a worthless car. While our car is abandoned in the driveway hoping for Chrysler to right their wrong, we still see lots of similar vehicles on the road. I'm guessing that their owners don't know that they're driving death traps either. We had a 2008 Tacoma with similar frame rust issues and Toyota recalled it almost a decade after it was manufactured, and replaced the entire frame. Chrysler should have to do the same to repair their shoddy and negligent design, or at least compensate us for the complete loss of value so that we can have some money to put towards its replacement. I also think that this issue needs to be publicly noted for all similar model years. We'd purchased this from a Chrysler dealership, and had checked the Carfax and Consumer Reports before purchasing this vehicle, and none of them noted these issues even though the vehicle was a few years old at the time. Vehicle has been repaired.*JB
- Electrical system · Fuel/propulsion system · Unknown or other
Key fob program
- Steering · Unknown or other · Wheels
I went on some errands before going out if town. I noticed I might need a wheel alignment soon and I parked the car in my garage to go out of town. When I returned to go have it checked out, I noticed my front driver side tire was flat and a closer inspection, it had a tear. Then I noticed my other…
I went on some errands before going out if town. I noticed I might need a wheel alignment soon and I parked the car in my garage to go out of town. When I returned to go have it checked out, I noticed my front driver side tire was flat and a closer inspection, it had a tear. Then I noticed my other front tire was flat as well. I had two people tell me my subframe was badly rusted. I found out this was a known problem with Chrysler Pacifica but no recalls. This could have been a horrible accident for my daughter and I. We had been on the highway! By the grace of GOD we made it home, but the car is not driveable. Then came COVID and here I am, still without a car. Chrysler said they don't do recalls. This should not happen. Unfortunately, I don't know how long this was going on, no one mentioned anything at oil changes or when I got 3 new tires, etc. I don't have photos and just lost and frustrated this happened.
- Engine · Unknown or other
My 2006 chrysler pacifica van has a corrosive chassis about break into, (meanimg) my engine is about to fall & hit the ground, this is my second chrysler, my first was a 2005 chrysler pacifica, when I bout the first one in 2014 they replace the chassis but I never thought to search Up under this…
My 2006 chrysler pacifica van has a corrosive chassis about break into, (meanimg) my engine is about to fall & hit the ground, this is my second chrysler, my first was a 2005 chrysler pacifica, when I bout the first one in 2014 they replace the chassis but I never thought to search Up under this one out of (well) even after I had taken them to a CHRYSLER DEALER no one ever told me at DEALERSHIP that I needed a chassis on either one or the 2005 nor the 2006 chrysler pacifica even when I took them in for services, I just don't understand now nor did I not get the kind of service then, I have put all kind of money in these cars mostly this one, window motor, #5fuel injector,electronic ignition,oil pump sensor,radiator,evac sensor, front struts, brakes,,,,now the chassis the gasket near the water pump ,2nd gas line which they say that I have to replace second fuel line cause it getting to much air which make my gas cap lite come on,,,,,how I mean why , I mean who can I turn to to fix or help me with these issues,
- Structure › Body · Suspension
Purchased this vehicle in 2013, inquired about defects and recalls but was told there was none. Vehicle had 46,000 miles on it at time of purchase 104K presently. Good running vehicle up to par on maintenance, which all goes to waste with a rotted subframe. Researched 100'S possibly 1000's of…
Purchased this vehicle in 2013, inquired about defects and recalls but was told there was none. Vehicle had 46,000 miles on it at time of purchase 104K presently. Good running vehicle up to par on maintenance, which all goes to waste with a rotted subframe. Researched 100'S possibly 1000's of complaints online with the same issue, where was mentioned nothing was done about it. Contacted chrysler myself to put in complaint and agent would not even forward it to the next level because the lack of recall or extended warranty. The cost for a new frame from a chrysler dealer IS over 2K and cost just as much to replace. But the part IS on back order for weeks. (Could this mean there are so many people in line waiting to order and needing this particular part?) cannot trust used parts because of many chrysler pacifica owners had to salvage their vehicle for the same reason. More of an investigation should be done into this. In the midst of a pandemic who can afford these outrageous, unexpected repair costs or even a new vehicle. My only option IS to salvage it for way less that it's worth, as I mentioned it drive great! I cannot sell it to anyone else knowing the safety hazard it has on it and I cannot afford a car payment. I am fearful of my engine falling out of the bottom if I drive it. Something has to be done, too many vehicles with the same issue. Force a recall on chrysler for their rotted subframes.
- Engine
I bought the car and 2 months later when I went to change the oil I noticed about hald my engine cradle gone due to rust
- Suspension
Noticed a lot of clunking coming from the front of our 2006 pacifica. Looked under vehicle and noticed rust and holes in the engine cradle. Took to my mechanic, he confirmed the engine cradle IS about to fail. I contacted burger chrysler in terre haute in. They stated vehicle IS not under any…
Noticed a lot of clunking coming from the front of our 2006 pacifica. Looked under vehicle and noticed rust and holes in the engine cradle. Took to my mechanic, he confirmed the engine cradle IS about to fail. I contacted burger chrysler in terre haute in. They stated vehicle IS not under any recall or safety notice. And fixing it would be out of my pocket. I researched the vehicle on the nhtsa web site. Need less to say I'm ashamed to own one. Chrysler will not stand behind what they mess up.
- Unknown or other
Transmission went out in 3 months
- Engine · Unknown or other
I bought this vehicle under the impression it needed a motor mount to find out that the sub frame IS rotten to the point it's a safety issue to drive. The rest of the details may not be of interest to you but I am the surviving spouse of a deceased veteran and mother of his two children. I've been…
I bought this vehicle under the impression it needed a motor mount to find out that the sub frame IS rotten to the point it's a safety issue to drive. The rest of the details may not be of interest to you but I am the surviving spouse of a deceased veteran and mother of his two children. I've been struggling to recuperate since their father's death and heaven unable to do to the pandemic that's what I was about to my daily drivers engine seized and I exhausted all my resources buying this vehicle that IS now deemed unsafe any help you can give me would be greatly appreciated
- Power train · Steering · Vehicle speed control
While drive turning left though a traffic light on pilot knob and 160th in farmington my car stalled wheel lock up paddle felt like it had gotten stuck for a second and there in the middle of the intersection my car had completely stalled out with my children in the vehicle to wear I had two…
While drive turning left though a traffic light on pilot knob and 160th in farmington my car stalled wheel lock up paddle felt like it had gotten stuck for a second and there in the middle of the intersection my car had completely stalled out with my children in the vehicle to wear I had two trucks pull over that had two stranger men that came over to push me out of the intersection out of danger when pulled off to the side of the road turn the car over and it did turn back on but because of the incident that I just happened I was not taking any chances of having it stalled going through a traffic intersection with my children in the car again so I had it towed home
- Unknown or other
I was drive my car and all of a sudden going through a street interaction on 170th street and pilot knob rd when it went dead on me the car wheel locked up and it stalled we're I almost could have got hit with my family in the car I and a few bypassers help me push it to the side of the road to…
I was drive my car and all of a sudden going through a street interaction on 170th street and pilot knob rd when it went dead on me the car wheel locked up and it stalled we're I almost could have got hit with my family in the car I and a few bypassers help me push it to the side of the road to we're I had aaa tow me me home because I felt it would be unsafe to drive in case it happen again and we get into a car accident so after I got the car home I was looking information up on why this could have happen on the chrysler dealership site to make a appt to have them find the problem when I came accross that there had been a recall on my car for what had happen for and there has been a few others that have had the same thing happen to them with the same car as me wrong IS the same thing that was recall that had been recall on my issued for my car so I need it to be fix before I put my family r me back in to drive as this IS a big safe issue it could happen again and next time who noise what could happen
- Structure › Body
I brought my car in for inspection. I also wanted them to check the muffler. I was contacted by the garage, they were not able to inspect the vehicle because the subframe under the engine IS completely rusted away. they said even if they could replace the muffler there would be nothing to attach…
I brought my car in for inspection. I also wanted them to check the muffler. I was contacted by the garage, they were not able to inspect the vehicle because the subframe under the engine IS completely rusted away. they said even if they could replace the muffler there would be nothing to attach it to. That's how deteriorated it IS. I would like to know if there IS any recourse I have ? I would like chrysler to be responsible for this defect. thank you, larry la bella
- Engine
I took my car in today to have shocks put on and was informed the engine cradle was so severely rusted the rack and pinion was about to drop out of the car along with the motor. I drive on the highway everyday and this would have broke in the next week or so and I would probably be severely injured or worse.
- Electrical system · Electronic stability control (esc) · Engine
Entered freeway battery light came on and lost power. Starting exiting freeway then car excelerating on its own. Engine was reving and humming so much I thought the engine would catch on fire. Car would not slow down. I had to put it in neutrual and hit the brakes as I exit the freeway to safely parked. Called tow truck for service.
- Suspension
The engine cradle on my 2006 chrysler pacifica touring IS almost completely rusted and cracked through. I took it to the mechanic because it was shaking and bucking and was told to stop driving it because one more bump could break the cradle causing my engine to drop. It will cost thousands of dollars to replace it. More than the car IS worth.
- Engine · Steering · Structure › Body
Bought car 2018 feb . No mention of whole under carriage rusted out - 2004-2008 chrysler forgot to spray for rust. When we go we bought it later in evening - was assured that car had been checked out and sound. We have done some repairs on other things - thermostat , radiator , tires ABS sensor…
Bought car 2018 feb . No mention of whole under carriage rusted out - 2004-2008 chrysler forgot to spray for rust. When we go we bought it later in evening - was assured that car had been checked out and sound. We have done some repairs on other things - thermostat , radiator , tires ABS sensor issue but there was no mention of underside being rusted from front to back - two years and the engine IS going to fall out and can no longer drive the car. This car was submerged in water somewhere before we received. This IS the shorter version of this situation. Alignment IS now way off , pulls to one side out of nowhere. Wearing on tires- just took it into heartland tire by house and told do not drive and that fixing it would be over 3500 or more.
- Suspension
TL* the contact owns a 2006 chrysler pacifica. The contact stated that upon taking her vehicle to an independent mechanic for service, she was informed that the engine cradle was extremely corroded. The contact's husband called ed martin chrysler dodge jeep RAM (2109 e 53RD st, anderson, in 46013)…
TL* the contact owns a 2006 chrysler pacifica. The contact stated that upon taking her vehicle to an independent mechanic for service, she was informed that the engine cradle was extremely corroded. The contact's husband called ed martin chrysler dodge jeep RAM (2109 e 53RD st, anderson, in 46013) and was informed that the vehicle was not subjected to a recall. The contact's husband was referred to the manufacturer for assistance. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was 190,000.
- Engine · Power train
TL* the contact owns a 2006 chrysler pacifica. The contact stated that while driving at various speeds, the vehicle stalled without warning. The contact and an independent mechanic replaced the fuel pump, the battery, alternator, throttle body and several other various parts however, the failure…
TL* the contact owns a 2006 chrysler pacifica. The contact stated that while driving at various speeds, the vehicle stalled without warning. The contact and an independent mechanic replaced the fuel pump, the battery, alternator, throttle body and several other various parts however, the failure persisted. The vehicle was taken to team hodges chrysler dodge RAM jeep (2265 M-76, west branch, mi 48661) and the contact was informed that the vehicle was not subjected to a recall. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 157,000.*dt*jb
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Fleet Vehicle Recall Completion Audit
On November 18, 2010, NHTSA's Recall Management Division (RMD) opened an audit query (AQ10-001) to investigate recall remedy completion by rental car companies on safety recall campaigns.It was expected to provide the agency an indication of how completely and how quickly rental car fleets perform necessary…
On November 18, 2010, NHTSA's Recall Management Division (RMD) opened an audit query (AQ10-001) to investigate recall remedy completion by rental car companies on safety recall campaigns.It was expected to provide the agency an indication of how completely and how quickly rental car fleets perform necessary recall-related remedies on the vehicles owned and then rented/leased for use on the roadways.RMD queried three (3) major motor vehicle manufacturers (Ford, Chrysler, and General Motors) and requested data regarding completion figures for fifteen (15) discreet safety recalls.Analysis of this data demonstrated that rental car recalls completion was neither complete nor consistent.The rental car companies representing the largest market share in the industry were then queried as to their respective policies for the rental, lease, and sale of vehicles with open recalls.The data and responses from the manufacturers and the rental car companies can be found in the document repository by accessing the ?Associated Documents link above.In December 2015, Congress enacted the Fixing America's Surface Transportation (FAST) Act.One section of the Act prohibits rental car companies from renting, leasing, or selling motor vehicles subject to open safety recalls.With the passage of the FAST Act and its prohibition, there is no continuing need for the agency to investigate rental car recall completions.Accordingly, this investigation is closed.The agency reserves the right to open any future investigations, including audits of individual recalls, or groups of recalls, or rental car companies, to examine more closely safety recalls performance and completion issues in this area.
- Engine stalling
In a november 8, 2006 letter, daimlerchrysler corporation (dcc) submitted a defect information report to nhtsa concerning two separate defect conditions that could result in engine stall while driving in model year (my) 2005-2006 chrysler pacifica vehicles (nhtsa recall no. 06V-432).my 2005 vehicles built in august…
In a november 8, 2006 letter, daimlerchrysler corporation (dcc) submitted a defect information report to nhtsa concerning two separate defect conditions that could result in engine stall while driving in model year (my) 2005-2006 chrysler pacifica vehicles (nhtsa recall no. 06V-432).my 2005 vehicles built in august and september of 2004 are being recalled to correct a defect in the secondary fuel pump modules, which may have an improper press fitting on the inlet that can become dislodged and shut-off fuel flow.all my 2005-2006 vehicles built between july 8, 2004 and november 11, 2005 are being recalled to correct a powertrain control module (pcm) software issue with the evaporative emissions system which can also cause stalling.for both conditions, engine stall incidents tend to occur during left turns. There were 17,375 vehicles built during august and september 2004 that were affected by both the fuel pump module and pcm software conditions.there were 30 voqs submitted to odi, 58 consumer complaints to dcc and 829 field reports relating to vehicles produced during this period.while these are mostly related to the fuel pump condition, some may have been caused by the software fault.the resulting stall while driving failure rate for this period IS 5,278 incidents per 100,000 vehicles.there were two crashes alleged to have resulted from these incidents.there were 1,021 warranty claims for fuel pump module replacement that appear related to engine stall (5.9% claim rate). The population for the remaining vehicles included in 06v-432 (i.e., those only affected by the software condition) IS 114,523.there were 97 voqs, 124 consumer complaints to dcc and 454 dcc field reports relating to these vehicles.the resulting stall while driving failure rate IS 589 per 100,000 vehicles.there were seven crashes alleged to have resulted from these incidents.there were 3,211 warranty claims for pcm reflash that appear related to engine stall in the total population of 131,898 vehicles (2.4% claim rate). All calculations are based on unique vins (multiple/repeat failures not included in these calculations) with no duplication across categories.dcc's recall will reprogram the pcm software and replace the fuel pump modules in all affected vehicles.this engineering analysis has been closed.
- Fuel tank punctures
Ea06-010 was opened based on information gathered in preliminary evaluation pe06-009.pe06-009 was opened based on information obtained in a peer information request as part of a preliminary evaluation (pe05-050) of fuel tank puncture in model year (my) 2003 through 2006 nissan murano vehicles.in january 2006, nissan…
Ea06-010 was opened based on information gathered in preliminary evaluation pe06-009.pe06-009 was opened based on information obtained in a peer information request as part of a preliminary evaluation (pe05-050) of fuel tank puncture in model year (my) 2003 through 2006 nissan murano vehicles.in january 2006, nissan submitted a defect information report to odi that identified a defect in the fuel tank shielding in approximately 209,000 my 2003 through 2006 nissan murano vehicles.to remedy the problem, nissan installed shields on the exposed front surfaces of the recalled vehicles.peer data collected for my 2004 through 2005 pacifica vehicles during pe05-050 included 120 field reports documenting tank replacements due to puncture or damage by road debris as part of a parts restriction program conducted at the request of the tank supplier (inergy). Analysis of the information provided by chrysler during pe05-050, pe06-009 and ea06-010 show that the front surface of the fuel tanks in the subject pacifica vehicles IS not completely protected fromroad debris by the floor pan or other body structure.the tanks were compared with peer vehicles, including several identified by chrysler as sharing similar design characteristics (unshielded high-density polyethylene plastic fuel tanks in a saddlebag configuration).some of the peer designs reviewed by odi packaged the tanks in recessed cavities in the floor pan or used shields to protect exposed surfaces on the front of the tank.in general, these tanks had the lowest complaint rates for tank puncture by road debris. However, other peer designs reviewed by odi had packaging similar to the subject vehicles and some of these also had some complaints of tank puncture.none of the peer vehicles analyzed by odi had tanks puncture data comparable to chrysler's field reports from its part restriction programs, so that data could not be used in peer comparisons. Analysis of the complaint data shows that the rate for the subject vehicles IS about half that observed in the recalled murano vehicles and not significantly higher than some of the peer vehicles analyzed with similar design characteristics.testing by the nhtsa vehicle research and testing center (vrtc) showed differences between the murano and pacifica fuel tank packaging and exposure to road debris thrown by the front tires.accordingly, this investigation IS closed.the closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist.the agency will continue to monitor complaints and other information relating to the alleged defect in the subject vehicles and take further action in the future if warranted.see document file for additional information regarding this resume.
- Engine stalling
On february 27, 2006 rq06-002 was opened in response to 60 complaints of engine stall, mostly during left-hand turns, in model year (my) 2004 to 2006 chrysler pacifica vehicles that were outside the scope of recall 04v-113.in march 2004, daimlerchrysler initiated recall 04v-113 on 34,561 my 2004 pacifica vehicles to…
On february 27, 2006 rq06-002 was opened in response to 60 complaints of engine stall, mostly during left-hand turns, in model year (my) 2004 to 2006 chrysler pacifica vehicles that were outside the scope of recall 04v-113.in march 2004, daimlerchrysler initiated recall 04v-113 on 34,561 my 2004 pacifica vehicles to correct a condition that could result in engine stall while making a left-hand turn after a cold-start.during rq06-002 it was determined that recall 04v-113 did correct the specific cause of the engine stalling condition for that specific population.however, two other conditions were identified that could also cause engine stalling during turning maneuvers:(1) an issue with misbuilt fuel pumps that primarily affected about 17,000 my 2005 pacifica vehicles built during august and september 2004; and (2) a software condition affecting vapor purge in about 131,000 my 2005-06 pacifica vehicles built from july 2004 through november 2005. An engineering analysis, ea06-013, has been opened to further examine the scope, frequency and safety consequences associated with each of these conditions in the subject vehicles.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10229256KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.
- 10229181Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10229178Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10223602Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223599Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10221686KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.
- 10221515Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10221512Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
- 10220489Valve Body. These may cause over drive cycling.
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10219706Magnesium Inner Liftgate Repair And Appearance Characteristics
- 1021645482212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
- 10209577Magnesium Inner Liftgate Repair And Appearance Characteristics
- 10191460Valve Body. These may cause over drive cycling.
- 10175743Disinfectant Solution Recommended for COVID-19
- 10175735Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
- 10169249Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10169247Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10169245Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10140239Magnesium Inner Liftgate Repair And Appearance Characteristics This bulletin involves discussing magnesium inner liftgate repair warnings and appearance characteristics.
- 10136932Part Description: Seat Belt - Retaining Button Kits. Issue Description: Do not replace the entire seat belt if the seat belt web stop button is missing or damaged.~Belt Web Button:~ 1D1 - Light Graystone - 05093280AB Belt Web Button~1D5 - Medium Slate Gray - 05093280AB Belt Web Button~1DA - Pastel Slate Gray - 05093280AB Belt Web Button~1J3 - Medium Khaki - 05093283AB Belt Web Button~ZJ3 - Medium Khaki - 05093283AB Belt Web Button~1L2 - Light Natural Beige - 05114207AA Belt Web Button~BD1 - Light Graystone - 05093280AB Belt Web Button~ BD5 - Medium Slate Grey - 05093280AB Belt Web Button~ BDA - Pastel Slate Gray - 05093280AB Belt Web Button~ ZP7 - Deep Seamist Green - 05093280AB Belt Web Button~ 5JB571D1A$, 5JB571D5A$, 5JB571J3A$, 5JX141D1A$, 5JX141D5A$, 5JX141DVA$, 5JX141J3A$, 5JX14ZJ3A$, 1EY841D1A$, 1EY841D5A$, 1EY841J3A$, 1EY851D1A$, EY851D5A$, 1EY851J3A$ use the following mini Belt Web Buttons:~1D1 - Light Graystone - 05093285AB Mini Belt Web Button~1D5 - Medium Slate Gray - 05093285AB Mini Belt Web Button~1DV - Slate Gray - 05093285AB Mini Belt Web Button~1J3 - Medium Khaki - 05093286AB Mini Belt Web Button~ZJ3 - Medium Khaki - 05093286AB Mini Belt Web Button~ Position the button as originally installed, or use the opposite side as reference.~ Web Button Location CS:~Front Driver O/B: 690 +/- 10 mm~Front Passenger O/B: 435 +/- 10 mm~Rear O/B: 435 +/- 10 mm~Rear Center: 290 +/- 10 mm~Rear Center Mini: 854 +/- 10 mm~ Web Button Location RG/RS SWB:~Front O/B: 550 +/- 6 mm~2nd Row O/B: 558 +/- 6 mm~ 3rd Row O/B: 584 +/- 6 mm~Web Button Location RG/RS LWB:~Front O/B: 550 +/- 6 mm~ 2nd Row O/B: 518 +/- 6 mm (Exception 52029368A$, 04680197A$: 690 +/- 6 mm)~ 3rd Row O/B: 585 +/- 6 mm (Exception 1CK35BD1A$, 1CK35BD5A$, 1CK35ZJ3A$, 52029369A$, 52029370A$: 434 +/-6 mm)~ Apply a small dot of Bond-All Gel, p/n 04467709, around the backside hole of the female button. Press the female button over the post of the male that is sticking through the rearwar
- 10130081Return: Wiring Assy - Engine You have been identified as either having stock, or have stock in transit to your dealership. Please return stock packaged before 2016/07/31 (31 July, 2016)of follow ing part numbers:68176457AF, 68176459AF. Please return suspect parts back to your facing depot using Return Code 02, before 13 September, 2016.
- 1013008005182535AD - Lamp Assy ?Tail Light LT You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05182535AD . See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
- 10130079Inspect and Return: Trim Cover Assy - A-Pillar Rt/Lt You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part numbers: 1ZA04DX9AE, 1ZA05DX9AE. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
- 10129047Warranty Operations Newsletter Updates from Warranty Operations
- 10129046Warranty Operations Newsletter Updates from Warranty Operations
- 10129045CBXDP361AA Return: Spacer Kit - Visor You have been identified as either having stock, or have stock in transit to your dealership. Please return stock of part number CBXDP361AA. Replacement part number is CBXDP361AB w hich is in stock and available for order. Please return suspect parts back to your facing depot using Return Code 02, before 16 September, 2016.
- 101290441NT30XDVAC - Inspect and Return: Panel - Instrument Panel You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 1N T30XDVAC. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
- 10129043Inspect and Return: Solenoid Module - Transmission You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of follow ing part numbers:52120000AA, 52119435AF, 05078709AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
- 10129042Return: Lamp Assy - CHMSL& Cargo Light You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of follow ing part numbers:55372082AE, 55372082AD, 55372082AC, 55372082AB, 55372082AA. Replacement part number is 55372082AF w hich is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
- 10129041P/N CBSZR068AA: Inspect & Return: Module Kit - Occupant Restraint You have been identified as either having stock, or have stock in transit to your dealership. Please return part number CBSZR068AA as per the QIR attached. Replacement part can be obtained by ordering the same part number (CBSZR068AA) Please return suspect parts back to your facing depot using Return Code 02, before 02 September, 2016.
- 1012900882212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
- 10121927NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
- 10121832Wiper If Mopar OE wipers are unavailable, the below alternatives can be offered instead. 05066964A$ = WBRW0011A$ 05066973A$ = WB000019A$ or WBF00019A$ 05096134A$ = WB000027A$ or WBF00028A$ 55154762A$ = WB000013A$ 68001330A$ = WB000019A$ or WBF00019A$ 05012611A$ = WB000021A$ or WBF00021A$ 05102881A$ = WBRW0011A$
- 10023351Exterior lamp - lens fogging.
- 10022179Wheel speed sensor service.
- 10021668Cleaning procedure for the mechanical throttle body.
Every Chrysler Pacifica model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.