1997 Chrysler Sebring Convertible
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Chrysler › Sebring Convertible › 1997
These records cover every 1997 Chrysler Sebring Convertible. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
3 recalls name the 1997 Chrysler Sebring Convertible. Newest first.
Federal-mogul IS recalling certain replacement control arm assemblies, part numbers k7425, 10945, fa4510x, k7427, 10946, and fa4611x, sold for use on various passenger vehicles listed above. the ball joint on the control arm assembly can fail causing the ball stud to wear through the control arm housing resulting in noise and/or separation of the ball stud…
Risk and remedy
Risk
If there IS a separation of the ball stud from the housing, the driver can loose steering control, possibly resulting in a vehicle crash.
Remedy
Federal-mogul will notify owners of record and replace the affected control arms free of charge. the safety recall began on january 28, 2011. owners may contact federal-mogul at 1-877-489-6659.
Qualis automotive IS recalling certain aftermarket ball joints sold for use on certain passenger vehicles. the socket may have been excessively hardened which could cause it to crack near the retaining ring groove allowing the ball stud to separate under impact load. the subject ball joints were sold as four part numbers, d10945, d10946, g10945, and…
Risk and remedy
Risk
Separation of the ball stud from the socket of the ball joint housing would allow the control arm to collapse and the wheel to fold in causing loss of steering control, possibly resulting in a crash.
Remedy
Qualis automotive will replace the ball joints free of charge. the safety recall began on november 9, 2009. owners may contact qualis automotive at 1-800-493-4128.
On certain passenger vehicles, the floor shifter ignition-park interlock may fail and allow the shifter to be moved out of the park position with the key removed. an inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position.
Risk and remedy
Risk
Either circumstance may result in the vehicle rolling away without warning.
Remedy
Dealers will install a new load-limiting push rod into the floor shifter lever of the affected vehicles. owner notification began on june 14, 2004. owners should contact daimlerchrysler at 1-800-853-1403.
Owner complaints
77 complaints8 involved a crash2 involved a fire12 injuries
What owners report most
Latest complaints
- Seat belts
Seat belts would not "pull out". At first it only happened sporadically and for short duration. Problem occurred more often until belts have not worked at all for past 2-3 weeks. *tr
- Suspension
TL* the contact owns a 1997 chrysler sebring convertible. the contact stated that the driver side ball joint detached from the socket while the contact was driving. the dealer diagnosed that the lower ball joint need to be replaced. the vehicle was included in the recall associated with nhtsa…
TL* the contact owns a 1997 chrysler sebring convertible. the contact stated that the driver side ball joint detached from the socket while the contact was driving. the dealer diagnosed that the lower ball joint need to be replaced. the vehicle was included in the recall associated with nhtsa campaign ID number: 09e056000 (suspension:front:control arm:lower ball joint), but the manufacturer refused to cover the repairs. The manufacturer proposed that the contact pay 50 percent of the cost of the repairs due to the age of the vehicle. The vehicle was not repaired. the failure and current mileage was 115,000.
- Seat belts
TL* the contact owns a 1997 chrysler sebring convertible. The contact stated that the driver side seat belt remained stuck in the retracted position and he was unable to use the seatbelt. the dealer informed the contact that there were no recalls and offered no further assistance. the…
TL* the contact owns a 1997 chrysler sebring convertible. The contact stated that the driver side seat belt remained stuck in the retracted position and he was unable to use the seatbelt. the dealer informed the contact that there were no recalls and offered no further assistance. the manufacturer had not been notified of the failure nor was the vehicle diagnosed or repaired. the current mileage was 111,320 and the approximate failure mileage was 111,300.
- Seat belts
I have a 1997 chrysler sebring jxi convertible, that the seatbelt are generally useless. both the passenger and driver seat belts lock and will not retrack, therefore you are not able to use them. this IS a safety hazard especially in a convertible. I live in a state where seatbelts are…
I have a 1997 chrysler sebring jxi convertible, that the seatbelt are generally useless. both the passenger and driver seat belts lock and will not retrack, therefore you are not able to use them. this IS a safety hazard especially in a convertible. I live in a state where seatbelts are requires, but when they are locked I can not use them. I have not found where the seatbelts have been recalled, shouldn't there be a lifetime guarantee on seatbelts since they are a safety device? I have owned the car for 3 years now and it IS an ongoing situation with the most recent being yesterday. *tr
- Suspension › Front
I was backing out of a friends driveway in my 1997 chrysler sebring convertible when all of a sudden there was a loud noise and a grinding sound. When I got out to look, it turns out that the front lower ball joint assembly broke in half by the front hub assembly. I then called a tow truck to have…
I was backing out of a friends driveway in my 1997 chrysler sebring convertible when all of a sudden there was a loud noise and a grinding sound. When I got out to look, it turns out that the front lower ball joint assembly broke in half by the front hub assembly. I then called a tow truck to have my vehicle towed and when the tow company came they informed me this was the 4TH chrysler convertible in two months that they have had to tow with the front lower ball joint breaking. I then decided to check for recalls and it turns out there are 2 recalls on this vehicle but when I contacted the loccal chrysler dealership they inform me that there IS no recall on my car. How can that be when you list the following recalls 04v021000, 09e056000 and 10e059000 on your website. I am just very thankful that I was not driving at a higher rate of speed when this happened or it could have been serious, like two of the other accidents that happened the tow truck driver shared with me. Two of the other vehicles he towed, the drivers were injured when the ball joint broke and they crashed.
- Electrical system
My 1997 sebring convertible oil light came on when I was driving in a heavy rain during rush hour. after stopping at a red light at a major highway intersection, my car died midway through the intersection. my oil pressure sensor wiring IS the cause for my fuel pump to cut off as a safety measure…
My 1997 sebring convertible oil light came on when I was driving in a heavy rain during rush hour. after stopping at a red light at a major highway intersection, my car died midway through the intersection. my oil pressure sensor wiring IS the cause for my fuel pump to cut off as a safety measure for the cars protection but almost cost me my life. after seeing the dealer and looking at online forums, I have found this IS common for the 2.7L engine in my car and many other autos made by damlier chrysler. if the 18 wheeler would have not changed lanes I would have died. I am waiting to replace the wiring because this IS several hundreds of dollars of work. *Tr
- Suspension › Front
While driving a1997 chrys. Sebring convertible across a bridge over a lake, the left front ball joint broke resulting in loss of control. I almost didn't stop before going in the water. Car blocked the highway and a patrolman stayed with me until wrecker arrived . It did major damage to front fender, plastic bumper brakes and wheel. *Tr
- Electrical system
Tl*the contact owns a 1997 chrysler sebring jxi. The contact stated that the odometer and gear lighting indicator failed. The vehicle was taken to an authorized dealership where the contact was informed that a loose electrical connection caused the odometer and gear light indicator to fail. The…
Tl*the contact owns a 1997 chrysler sebring jxi. The contact stated that the odometer and gear lighting indicator failed. The vehicle was taken to an authorized dealership where the contact was informed that a loose electrical connection caused the odometer and gear light indicator to fail. The vehicle had not been repaired because the contact stated that when she drove over a bump in the road, the odometer worked. The failure mileage was approximately 35,000. The current mileage was approximately 40,000.
- Electrical system
Electrical system failure. computer will no longer "go to sleep" and drains the battery. the car must now be jump started with a portable booser pack that I carry in the car. dealer claims the computer must be replaced at a cost of $1,000 plus to fix the problem. *tr
- Unknown or other
Tl*the contact owns a 1997 chrysler sebring convertible. while approaching a stop sign, a police officer informed the driver that the undercarriage of the vehicle was on fire. the driver exited the vehicle just as it became completely engulfed in flames. there were no injuries, but both a police and fire report were filed. the current and failure mileages were 91,000.
- Electrical system
Purchased 1997 chrysler sebring convertible. In 1998 the instrument cluster started to fail intermittently. the tachometer, and odometer fade in and out, out mostly. Cant see mileage, so cant sell car. dealer says cost IS about $600 to fix. And IS common problem. if its so common, it should be a recall!!! *tr
- Electrical system
Electronic odometer and tachometer display work intermittently. Dealer explains that it IS common with this car model. Difficult to track service on the vehicle. Also will be difficult to sell with out fix which will be over $500 for instrument cluster and could involve individual gauges which will cost around $380. Chrysler should recall and pay for this. *tr
- Structure › Body
Sebring convertible interior floods every time it rains the carpet becomes completely soaked and takes days to dry out in the mean time causing a concern about all electrical components under the seats. *tr
- Electrical system
Problem with dash cluster speedo and tach quit working dealer said they see it all the time on this car. *tr
- Seat belts
Occasionally, the seatbelt on on my 1997 chrysler sebring locks up. when it does, it cannot be extended/pulled out. this has happened numerous times. when it happens, both seatbelts freeze, leading to the conclusion that it IS an electrical problem. sometimes, after waiting a half hour or so…
Occasionally, the seatbelt on on my 1997 chrysler sebring locks up. when it does, it cannot be extended/pulled out. this has happened numerous times. when it happens, both seatbelts freeze, leading to the conclusion that it IS an electrical problem. sometimes, after waiting a half hour or so, the problem corrects itself. in the meantime, unless I have time to wait, I must drive without the safety of my seatbelt, which not only puts my life at risk, but makes me a lawbreaker and potentially liable for a ticket. I have called several chryler dealers, none of whom admits to having heard of the problem and all of whom want to run expensive tests to diagnose the problem. a quick google search shows that many many people have had the exact same problem. it IS a potentially life-threatening situation, and we need the government to step in an help us please! *tr
- Steering › Hydraulic power assist system
Tl*the contact owns a 1997 chrysler sebring convertible. he noticed a constant leak on the high pressure power steering hold. a mechanic diagnosed the failure. the failure mileage was 116,000 and the current mileage was 117,000.
- Suspension › Front › Control arm › Lower ball joint
Tl*the contact owns a 1997 chrysler sebring convertible. on july 9, 2007, while driving 10 mph, the control arm detached from the vehicle. the failure caused the axle to fall off the vehicle. there were no warning indicators prior to the failure. the control arm and axle were replaced on july…
Tl*the contact owns a 1997 chrysler sebring convertible. on july 9, 2007, while driving 10 mph, the control arm detached from the vehicle. the failure caused the axle to fall off the vehicle. there were no warning indicators prior to the failure. the control arm and axle were replaced on july 11, 2007 for $1,080. the dealer stated that her vin was excluded from recall # 00v421002 (suspension:front:control arm:lower ball joint). the current and failure mileages were 135,000.
- Air bags › Frontal
1997 sebring passenger side airbag exploded. *ts *jb
- Electrical system
Odometer functions intermittently. this IS a known, common problem, but chrysler has not recalled. it causes problems whenever you need to purchase anything for your vehicle (tires, oil change, parts etc). please recall and fix this issue! *nm
- Fuel system, gasoline › Delivery › Hoses, lines/piping, and fittings
Dt: the contact owns a 1997 chrysler sebring convertible. The fuel pipe was corroded and dripped gasoline, and was less that one foot from the muffler. When the contact went to purchase the part for car the salesman said he was about the 15 person to buy the part. The consumer called chrysler…
Dt: the contact owns a 1997 chrysler sebring convertible. The fuel pipe was corroded and dripped gasoline, and was less that one foot from the muffler. When the contact went to purchase the part for car the salesman said he was about the 15 person to buy the part. The consumer called chrysler, and they said there was not a problem. He was going to repair the problem. This was the contact daughter's car, and he was concerned for his daughter's safety and those of others. *Ak
- Engine and engine cooling › Engine
Known engine problems with chryslers 2.4L - 4 cylinder engines - defective head gaskets. We purchased a new 1997 chrysler sebring JX w/ 2.4L DOHC 4 cylinder engine in march of 1998. vehicle was purchased new and maintained by nalley chrysler in roswell. vehicle has a little over 19,000 actual…
Known engine problems with chryslers 2.4L - 4 cylinder engines - defective head gaskets. We purchased a new 1997 chrysler sebring JX w/ 2.4L DOHC 4 cylinder engine in march of 1998. vehicle was purchased new and maintained by nalley chrysler in roswell. vehicle has a little over 19,000 actual miles and should not have any engine problems with this low mileage or use. vehicle was inspected on several occasions for leaking coolant/oil mixture complained of leaks to service reps on several occasions, nothing found. at last recall - shifter linkage, asked service technician to check for coolant leaks was informed that 2.4L engine will need a new head gasket. internet searches show many occurrences of problems with this 2.4L engine as heads are made of different material than block and they cool and heat at differing rates causing excessive movement and failure of the head gasket. Chrysler has silently warranted many of these engines because of head gasket failures and known problems and defects. would request reimbursement or repair. Chrysler rep had denied repair. Class action status should be investigated for these known engine problems. *jb
- Electrical system › Wiring › Fuses and circuit breakers
1) the vehicle was parked outside securely (doors and windows closed properly, top closed properly, ignition locked and no keys in the car). 2) after a rain, I happened to walk by the car and heard it making loud strange noises that sounded like speaker amplified electrical arcing. the noise…
1) the vehicle was parked outside securely (doors and windows closed properly, top closed properly, ignition locked and no keys in the car). 2) after a rain, I happened to walk by the car and heard it making loud strange noises that sounded like speaker amplified electrical arcing. the noise seemed to be coming from everywhere in the vehicle (no apparent point source). suspecting some type of electrical problem I began pulling fuses with no effect on stopping the noise. I began smelling something burning and disconnected the car battery. the noises stopped immediately and the burning smell dissapated. 3) the dealer advises that there IS a drain in the right rear quarter panel of the car that IS not working and causes water to enter the passenger compartment. there IS an amplfier under the front passenger seat for the infinity sound system that water had entered into. dealer advises that the failed part must be returned to the manufacturer to get a replacement and that further damage cannot be determined until the replacement part IS installed. there are two design defects in this car, one of which IS a serious safety concern. the first defect IS the rear quarter panel drains that can stop working and flood the car resulting in significant damage.the owner IS not made aware of this defect or how to prevent the problem. the second design defect IS a safety concern. an amplifier under the passenger seat has no fuse protection whatsoever. if I had not happened by the car when I did, and had not disconnected the car battery, the car was beginning to catch fire (i smelled burning!). this amplifier can malfunction electrically and start an electrical fire in the vehicle without any electrical interupt protection available. had I not disconnected the battery when I did this car could have caught fire as a result of this lack of any short circuit protection.
- Air bags › Frontal · Power train › Axle assembly · Seat belts › Front
Dt: the contact received a recall letter on 3-15-05 concerning the trans axle floor shifter ignition/park interlock she called at the end of march or the beginning of april and made an appointment to have vehicle checked. On 5-7-05, before the scheduled appointment, the vehicle popped out of…
Dt: the contact received a recall letter on 3-15-05 concerning the trans axle floor shifter ignition/park interlock she called at the end of march or the beginning of april and made an appointment to have vehicle checked. On 5-7-05, before the scheduled appointment, the vehicle popped out of gear and hit a pole. And the estimated damage was $8,700. On 5-12-05 chrysler sent an investigator to check the vehicle . The consumer was not present at the inspection, but someone else who was at the inspection claimed that the investigator tried to start the car and it wouldn't start. he did not think the trans axle floor shifter ignition/park interlock had anything to do with the crash. The consumer did not agree, stating that the driver and the passenger were injured in the crash. Neither the seat belts nor the air bags worked in the crash.*ak
- Air bags · Seat belts · Vehicle speed control
Dt: consumer received recall 04v021000, on march 15, 2005. she had called dealer to arrange for repairs, but they told her to bring the vehicle in at her convenience. The recall work was never performed. on may 7, 2005 she was picking her daughter and while the vehicle was in park it went…
Dt: consumer received recall 04v021000, on march 15, 2005. she had called dealer to arrange for repairs, but they told her to bring the vehicle in at her convenience. The recall work was never performed. on may 7, 2005 she was picking her daughter and while the vehicle was in park it went down a small hill in a parking lot and traveled at least 200-300 feet. the vehicle was also turned off. this happened so fast she could not remember whether the brakes worked at that time. there was a telephone pole that stopped the vehicle. upon impact, the airbags did not deploy, and the seat belts did not restrain the passengers. the passengers head went through the windshield and her knees hit the dash board. the driver's right rotor cuff and neck were injured. there was $8700 worth of damage to the vehicle, and it was totaled. the manufacturer stated that they could not do anything about it. a inspector from daimler chrysler inspected vehicle on may 12, 2005 at 2 pm. he never spoke to the consumer, but the manufacturer sent a report.*ak
- Air bags · Power train › Automatic transmission › Lever and linkage › Floor shift · Seat belts
Dt: was driving at an unknown speed and pulled in front of a bowling alley to pick up another passenger. turned the engine off with key in ignition, within a matter of seconds the vehicle began to roll forward. the car gained speed and was too quick before the consumer could gain control. the…
Dt: was driving at an unknown speed and pulled in front of a bowling alley to pick up another passenger. turned the engine off with key in ignition, within a matter of seconds the vehicle began to roll forward. the car gained speed and was too quick before the consumer could gain control. the vehicle went down an incline and crashed into a parking lot pole. the air bags did not deploy. both passenger had seat belts on but passenger seat belt did not remain locked and passenger struck the windshield, this did not unlatch but a great deal slack came from that seat belt. had received a recall on the transaxles floor shift(no nhtsa recall camp ID# available) this recall had not been performed. a inspector from chrysler came out to impasses vehicle who later noted this incident was not due the recall but consumer does not know how he made this assumption because he just looked at vehicle-the vehicle was locked up at the time. no repairs have been made. dealer did make aware there was also a recall on throttle as well(no nhtsa recall ID at this time.) dealer and chrysler are unwilling to cover damages as well the recall repair.*ak
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Auto trans ignition-park interlock
The manufacturer reports above are based on daimlerchrysler?s (dc) analysis of model year (my) 1998 (population = 356,384) and 1999 (population = 486,948) ja, JX and lh family subject vehicle data (earlier mys excluded).the population number includes all mys.the precise number of duplicates between odi and dc reports…
The manufacturer reports above are based on daimlerchrysler?s (dc) analysis of model year (my) 1998 (population = 356,384) and 1999 (population = 486,948) ja, JX and lh family subject vehicle data (earlier mys excluded).the population number includes all mys.the precise number of duplicates between odi and dc reports cannot be determined due to missing or incomplete information.the fatality incident involved an elderly person who attempted to stop a roll away vehicle and received fatal injuries.odi also gathered information on my 1997-99 prowler vehicles in this investigation. The prowler vehicles were manufactured with a different design shifter mechanism (the shift lever IS shorter).there are no complaints of prowler interlock failure in odi?s database, and dc has received no reports either.the prowler IS excluded from the recall scope.the investigation involved a condition where the interlock system could fail (or be made inoperative by the operator) during vehicle use, possibly inadvertently.the interlock system IS required under fmvss 114.with the transmission in the park position and the ignition key off, the combined action of pressing the shift button and pulling the shift lever rearward may result in the operator overcoming the interlock system and cause the mechanical linkage of the system to disconnect.when this occurs, there IS no overt indication to an operator that the system IS defeated, and an increased risk of vehicle roll-away exists.under recall 04v021, dc will replace damaged shift mechanisms, and will install on all vehicles a device which inhibits the operator?s ability to overcome the interlock and defeat the system.beginning with my 2000, dc incorporated a brake and transmission shifter interlock (btsi) system into the subject vehicles.introduction of btsi involved design changes to the shift mechanism, one of which resulted in reduced mechanical advantage (rma) of the shift button.the rma shifter requires increased forces to overcome the interlock system, making the shifter less susceptible to damage.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10220489Valve Body. These may cause over drive cycling.
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 1021645482212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
- 10191460Valve Body. These may cause over drive cycling.
- 10175735Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
- 10169249Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10169247Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10169245Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10130081Return: Wiring Assy - Engine You have been identified as either having stock, or have stock in transit to your dealership. Please return stock packaged before 2016/07/31 (31 July, 2016)of follow ing part numbers:68176457AF, 68176459AF. Please return suspect parts back to your facing depot using Return Code 02, before 13 September, 2016.
- 1013008005182535AD - Lamp Assy ?Tail Light LT You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05182535AD . See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
- 10130079Inspect and Return: Trim Cover Assy - A-Pillar Rt/Lt You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part numbers: 1ZA04DX9AE, 1ZA05DX9AE. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
- 10129047Warranty Operations Newsletter Updates from Warranty Operations
- 10129046Warranty Operations Newsletter Updates from Warranty Operations
- 10129045CBXDP361AA Return: Spacer Kit - Visor You have been identified as either having stock, or have stock in transit to your dealership. Please return stock of part number CBXDP361AA. Replacement part number is CBXDP361AB w hich is in stock and available for order. Please return suspect parts back to your facing depot using Return Code 02, before 16 September, 2016.
- 101290441NT30XDVAC - Inspect and Return: Panel - Instrument Panel You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 1N T30XDVAC. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
- 10129043Inspect and Return: Solenoid Module - Transmission You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of follow ing part numbers:52120000AA, 52119435AF, 05078709AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
- 10129042Return: Lamp Assy - CHMSL& Cargo Light You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of follow ing part numbers:55372082AE, 55372082AD, 55372082AC, 55372082AB, 55372082AA. Replacement part number is 55372082AF w hich is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
- 10129041P/N CBSZR068AA: Inspect & Return: Module Kit - Occupant Restraint You have been identified as either having stock, or have stock in transit to your dealership. Please return part number CBSZR068AA as per the QIR attached. Replacement part can be obtained by ordering the same part number (CBSZR068AA) Please return suspect parts back to your facing depot using Return Code 02, before 02 September, 2016.
- 10001520Seat belt cinch bar service for various models including 2004 models.
- 6092304Subject regarding non-deployed airbag handling procedures.
- 6089800Daimlerchrysler corporation IS now offerinb airbag on / off switches for selected vehicles.
- 634272Flash programming failure recovery. *Slc
- 629129On some vehicles the rear window defogger IS inoperative and defogger grid terminal(s) IS separated from the rear window heating grid and/or may be broken.
- 621898Automatic transmission fluid usage ATF+4.
- 620066Subject regarding generic scan tool (gst), publication no. 81-170-00008 provided with this technical service bulletin to provide reference information when using generic scan tool on obdii vehicles.
- 620059Subject regarding airbag / clock spring service for various models including 2002 model year jeep liberty.
- 620058A condition may exist with the rear window defogger inoperative and defogger grid terminal(s) may separate from the rear window heating grid or be broken.
- 618049Subject regarding wire splice repairs.
- 612149Vehicles may experience clunking or rattle in steering wheel/steering column. *Mjs
- 610007Daimlerchrysler corporation IS now offering internal emergency trunk releases for selection vehicles.
- 609995This bulletin provides a revised wire splice procedure and related parts.
- 609988Subject regarding misdiagnosed leak detection pump systems with diagnostic trouble codes p1494, p0442 p0455, or p0456.
- 608371Daimler chrysler IS now offering internal emergency trunk releases for selected vehicles.
- 607916Technical service bulletin regarding multi-layer steel (mls) head gasket installation procedures.
- 607914Information regarding 2.5L V-6 head gasket application.
- 607298This bulletin explains the operation and application of the leak detection pump (ldp) monitor test.
- 605926Customer satisfaction notification regarding covertible top cover instruction label.
- 605014Conditions with intermittent loss of speed control.
Every Chrysler Sebring Convertible model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.